The color that is reflected when a red card is illuminated by red light is white.
The color an object is perceived to have, depends on the frequency of light it reflects.
If white light incidents on a red filter, red is transmitted while blue and green are absorbed.
Consequently, when a red card is illuminated by red light, the red card will reflect back almost all the incident light on it, causing it to appear brighter which creates an illusion of white color to the eyes.
Thus, we can conclude the color that is reflected when a red card is illuminated by red light is white.
Learn more here:https://brainly.com/question/3495999
Define the following, and give the letter which we will abbreviate them by:
Center of curvature:
Vertex:
Focal Point:
Radius of curvature:
Focal length:
Answer:
As in explanation.
Explanation:
A) Centre of Curvature: This is defined as the point in the center of the sphere from which the mirror was sliced. It is represented by the letter "C"
B) Vertex: It is defined as the point on the mirror's surface where the principal axis meets the mirror. It is represented by the letter A.
C) Focal Point: This is defined as the Midway point between the vertex and the center of curvature. It is represented by the letter "F"
D) Radius of Curvature: This is defined as the distance from the vertex to the center of curvature. It is represented by the letter "R"
E) Focal Length: This is defined as the distance from the mirror to the focal point. It's represented by the letter "f"
A positive point charge q is placed at the center of an uncharged metal sphere insulated from the ground. The outside of the sphere is then grounded as shown. Then the ground wire is removed. A is the inner surface and B is the outer surface. Which statement is correct
Explanation:
the missing figure in the Question has been put in the attachment.
Then from the figure we can observe that
the center of the sphere is positive, therefore, negative charge will be induced at A.
As B is grounded there will not be any charge on B
Hence the answer is A is negative and B is charge less.
A rock weighing 20 N (mass = 2 kg) is swung in a horizontal circle of radius 2 m at a constant speed of 6 m/s. What is the tension in the cord?
Answer:
The tension in the cord provides by centripetal force
T = Fc
= mv^2/r
= 2kg ( 6)^2/2
=36 N
One day, after pulling down your window shade, you notice that sunlight is passing through a pinhole in the shade and making a small patch of light on the far wall. Having recently studied optics in your physics class, you're not too surprised to see that the patch of light seems to be a circular diffraction pattern. It appears that the central maximum is about 1 cm across, and you estimate that the distance from the window shade to the wall is about 4 m.
Estimate:
a. The average wavelength of the sunlight (in nm)
b. The diameter of the pinhole (in mm).
Given that,
Central maximum = 1 cm
Distance from the window shade to the wall =4 m
We know that,
The visible range of the sun light is 400 nm to 700 nm.
(a). We need to calculate the average wavelength
Using formula of average wavelength
[tex]\lambda_{avg}=\dfrac{\lambda_{1}+\lambda_{2}}{2}[/tex]
Put the value into the formula
[tex]\lambda_{avg}=\dfrac{400+700}{2}[/tex]
[tex]\lambda_{avg}=550\ nm[/tex]
(b). We need to calculate the diameter of the pinhole
Using formula for diameter
[tex]w=\dfrac{2.44\lambda L}{D}[/tex]
[tex]D=\dfrac{2.44\lambda L}{w}[/tex]
Put the value into the formula
[tex]D=\dfrac{2.44\times550\times10^{-9}\times4}{1\times10^{-2}}[/tex]
[tex]D=0.537\ mm[/tex]
Hence, (a). The average wavelength 550 nm.
(b). The diameter of the pinhole is 0.537 mm.
1 of 3 : please help got an extra day for a test and i don’t get this (must show work) points and brainliest!
Answer:
y = 1/2at^2
we could also write it as-
y = (at^2)/2
2y = at^2
2y/a = t^2
√2y/a = t
hope it helps
how many stars are in our solar system?
Answer:
there are over 100 billion stars in our galaxy.
Are Quantum Physics, Quantum mechanics,Quantum Engagement same?
or, Do they branch of each others
Answer:
The topic of quantum entanglement is at the heart of the disparity between classical and quantum physics: entanglement is a primary feature of quantum mechanics lacking in classical mechanics. ... In the case of entangled particles, such a measurement will affect the entangled system as a wholeExplanation:
Answer:
quantum entanglement is thought to be one of the trickiest concepts in science, but the core issues are simple. And once understood, entanglement opens up a richer understanding of concepts such as the “many worlds” of quantum theory.
Explanation:
What will be the nature of the image formed from both a convex lens and a concave
lens of 20 centimeter focus distance, when the object is placed at a distance of
10 centimeters?
Answer:
Explanation:
Using the lens formula
1//f = 1/u+1/v
f is the focal length of the lens
u is the object distance
v is the image distance
For convex lens
The focal length of a convex lens is positive and the image distance can either be negative or positive.
Given f = 20cm and u = 10cm
1/v = 1/f - 1/u
1/v = 1/20-1/10
1/v = (1-2)/20
1/V = -1/20
v = -20/1
v = -20 cm
Since the image distance is negative, this shows that the nature of the image formed by the convex lens is a virtual image
For concave lens
The focal length of a concave lens is negative and the image distance is negative.
Given f = -20cm and u = 10cm
1/v = 1/f - 1/u
1/v = -1/20-1/10
1/v = (-1-2)/20
1/V = -3/20
v = -20/3
v = -6.67 cm
Since the image distance is negative, this shows that the nature of the image formed by the concave lens is a virtual image
g Two point sources emit sound waves of 1.0-m wavelength. The source 1 is at x = 0 and source 2 is at x = 2.0 m along x-axis. The sources, 2.0 m apart, emit waves which are in phase with each other at the instant of emission. Where, along the line between the sources, are the waves out of phase with each other by π radians?
Answer:
constructive interferencia 0, 1 , 2 m
destructive inteferencia 1/4, 3/4. 5/4, 7/4 m
Explanation:
This exercise is equivalent to the double slit experiment, the two sources are in phase and separated by a distance, therefore the waves observed in the line between them have an optical path difference and a phase difference, given by the expression
Δr / λ = Φ / 2π
Δr = Φ/2π λ
let's apply this expression to our case
λ = 1 m
Δr = Φ 1 / 2π
We have constructive interference for angle of Φ = 0, 2π, ...
let's find the values where they occur
Φ Δr
0 0
2π 1
4π 2
Destructive interference occurs by Φ = π /2, 3π / 2, ...
Φ Δr
π/2 ¼ m
3π /2 ¾ m
5π /2 5/4 m
7π /2 7/4 m
a. The molecules of a magnet are independent...
Answer:
variable
Explanation:
As a skydiver falls, his potential energy ___ and his kinetic energy __
increases,increases
increases,decreases
decreases,increases
decreases, decreases
Answer:
Hey there!
PE=mgh, so as height decreases, so does the potential energy.
KE=mv^2, so as velocity increases, kinetic energy increases.
Thus, the correct answer would be Decreases, Increases.
Let me know if this helps :)
A particle undergoes damped harmonic motion. The spring constant is 100 N/m, the damping constant is 8.0 x 10-3 kg.m/s, and the mass is 0.050 kg. If the particle starts at its maximum displacement, x = 1.5 m, at time t = 0. What is the amplitude of the motion at t = 5.0 s?
Answer:
The amplitude [tex]A(5) = 1 \ m[/tex]
Explanation:
From the question we are told that
The spring constant is [tex]k = 100 \ N/m[/tex]
The damping constant is [tex]b = 8.0 *10^{-3} \ kg \cdot m/s[/tex]
The mass is [tex]m = 0.050 \ kg[/tex]
The maximum displacement is [tex]A_o = 1.5 \ m \ at t = 0[/tex]
The time considered is t = 5.0 s
Generally the displacement(Amplitude) of damped harmonic motion is mathematically represented as
[tex]A(t) = A_o * e ^{ - \frac{b * t}{2 * m} }[/tex]
substituting values
[tex]A(5) = 1.5 * e ^{ - \frac{ 8.0 *10^{-3} * 5}{2 * 0.050} }[/tex]
[tex]A(5) = 1 \ m[/tex]
13. A sinusoidal wave of frequency f is traveling along a stretched string. The string is brought to rest, and a second traveling wave of frequency 2f is established on the string. What is the wavelength of the second wave?
Answer:
It will be half that if the first wave
Explanation:
Because the wave speed remains the same, the result of doubling the frequency is that the wavelength is half as large as it
Explain why water, with its high specific heat capacity, is utilized for heating systems such as hot-water radiators.
Answer:
Answer in explanation
Explanation:
Water is mainly used as coolant in heating systems like hot-water radiators. The main function of water in such systems, is to absorb as much heat as possible, in order to decrease the temperature of the system and as a result cool it.
The specific heat capacity is the measure of heat energy that is required to raise the temperature of unit mass of a substance through 1 °C. In other words, specific heat capacity quantifies the amount of heat that can be stored by a unit mass of a substance having a degree rise in temperature.
Thus, the more specific heat a substance has, the more heat it can absorb from the hot system. Hence, the specific heat capacity of a coolant must be high.
This is the reason why water, with its high specific heat capacity, is utilized for heating systems, such as radiators.
Light with an intensity of 1 kW/m2 falls normally on a surface and is completely absorbed. The radiation pressure is
Answer:
The radiation pressure of the light is 3.33 x 10⁻⁶ Pa.
Explanation:
Given;
intensity of light, I = 1 kW/m²
The radiation pressure of light is given as;
[tex]Radiation \ Pressure = \frac{Flux \ density}{Speed \ of \ light}[/tex]
I kW = 1000 J/s
The energy flux density = 1000 J/m².s
The speed of light = 3 x 10⁸ m/s
Thus, the radiation pressure of the light is calculated as;
[tex]Radiation \ pressure = \frac{1000}{3*10^{8}} \\\\Radiation \ pressure =3.33*10^{-6} \ Pa[/tex]
Therefore, the radiation pressure of the light is 3.33 x 10⁻⁶ Pa.
An electric device delivers a current of 5.0 A to a circuit. How many electrons flow through this circuit in 5 s?
Answer:
1.6×10²⁰
Explanation:
An ampere is a Coulomb per second.
1 A = 1 C / s
The amount of charge after 5 seconds is:
5.0 A × 5 s = 25 C
The number of electrons is:
25 C × (1 electron / 1.6×10⁻¹⁹ C) = 1.6×10²⁰ electrons
Design a voltage divider to provide the following approximate voltages with respect to ground using a 30 V source: 8.18 V, 14.7 V, and 24.6 V. The current drain on the source must be limited to no more than 1 mA. The number of resistors, their values, and their wattage ratings must be specified. A schematic showing the circuit arrangement and resistor placement must be provided
Answer:
R₁ = 14.7 10³ Ω , R₂ = 8.18 10³ Ω , R₃ = 1.72 10³ Ω , R₄ = 5.4 10³ Ω 1/8 W resistor
Explanation:
For this exercise we must use a series circuit since the sum of the voltage on each resin is equal to the source voltage (V = 30 V)
Therefore we build a circuit with 4 resistors in series, in such a way that
V = i R
let the voltage
1st resistance
V = i R
R₁ = V / i
R₁ = 14.7 / 1 10⁻³
R₁ = 14.7 10³ Ω
power is
P = V i
P = 14.7 1 10⁻³
P = 14.7 10⁻³ W = 0.0147 W
a resistance of ⅛ W is indicated
2nd resistance
R₂ = 8.18 / 1 10⁻³
R₂ = 8.18 10³ Ω
Power
P = 8.18 1 10⁻³
P = 0.00818W
a 1/8 W resistor
3rd resistance
this resistance is calculated in such a way that
V₁ + V₂ + V₃ = 24.6
V₃ = 24.6 - V₁ -V₂
V₃ = 24.6 - 14.7 - 8.18
V₃ = 1.72 V
R₃ = 1.72 / 1 10⁻³
R₃ = 1.72 10³ Ω
power
P = Vi
P = 1.72 10⁻³
P = 0.00172 W
a resistance of ⅛ W
To obtain the voltage of 24.6 we use this three resistors together
4th resistance
The value of this resistance is calculated so that the sum of all the voltages reaches the source voltage
30 = V₁ + V₂ + V₃ + V₄
V₄ = 30 - V₁ -V₂ -V₃
V₄ = 30 -14.7 - 8.18 - 1.72
V₄ = 5.4 V
R₄ = 5.4 / 1 10⁻³
R₄ = 5.4 10³ Ω
Power
P = V i
P = 5.4 10⁻³
P = 0.0054 W
⅛ W resistance
The values of these resistance are commercially
Let's check the consumption of the circuit
R_total = R₁ + R₂ + R₃ + R₄
R_total = (14.7 + 8.18 + 1.72 + 5.4) 10³
R_total = 30 10³
the current circulating in the circuit is
i = V / R_total
i = 30/30 10³
i = 1 10⁻³ A
therefore it is within the order requirement.
for connections see attached diagram
A lamp in a child's Halloween costume flashes based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.220 s, during which it produces an average 0.520 W from an average 3.00 V.
A. How much charge moves through the lamp (C)?
B. Find the capacitance (F).
C. What is the resitance of the lamo?
Answer:
A. 0.0374C
B. 0.012F
C. 18 ohms
Explanation:
See attached file
6. You push an object, initially at rest, across a frictionless floor with a constant force for a time interval t, resulting in a final speed of v for the object. You then repeat the experiment, but with a force that is twice as large. What time interval is now required to reach the same final speed v?
Answer:
t = t₀ / 2
Explanation:
In this exercise we must use Newton's second law
F = m a
a = F / m
now we can use kinematics
as in object part of rest (v₀ = 0)
v =a t₀
t₀ = v / a
these results are with the first experiment
now repeat the experiment, but F = 2F₀
a = 2F₀ / m = 2 a₀
v = 2 a₀ t
t = v / 2a₀
t = t₀ / 2
The time interval that is required to reach the same final speed (V) is equal to [tex]t=\frac{\Delta t}{2}[/tex].
Given the following data:
Initial speed = 0 m/s (since the object is at rest)Final speed = VTime = [tex]\Delta t[/tex]Speed = VTo find the time interval that is now required to reach the same final speed (V), we would apply Newton's Second Law of Motion:
Mathematically, Newton's Second Law of Motion is given by this formula;
[tex]F = \frac{M(V-U)}{t}[/tex]
Where:
F is the force.V is the final velocity.U is the initial velocity.t is the time.Substituting the given parameters into the formula, we have;
[tex]F = \frac{M(V-0)}{\Delta t}\\\\F = \frac{MV}{\Delta t}[/tex]
When the experiment is repeated, the magnitude of the force is doubled:
[tex]F = 2F[/tex]
Now, we can find the time interval that is required to reach the same final speed (V):
[tex]F = \frac{M(V-0)}{t}\\\\t=\frac{MV}{F}[/tex]
Substituting the value of F, we have:
[tex]t=\frac{MV}{2F} \\\\t=\frac{MV}{\frac{2MV}{\Delta t}} \\\\t=MV \times \frac{\Delta t}{2MV} \\\\t=\frac{\Delta t}{2}[/tex]
Read more here: https://brainly.com/question/24029674
Light of wavelength 519 nm passes through two slits. In the interference pattern on a screen 4.6 m away, adjacent bright fringes are separated by 5.2 mm in the general vicinity of the center of the pattern. What is the separation of the two slits?
Answer:
The separation of the two slits is 0.456 mm.
Explanation:
Given the wavelength of light = 519 nm
The indifference pattern = 4.6 m
Adjacent bright fringes = 5.2 mm
In the interference, the equation required is Y = mLR/d
Here, d sin theta = mL
L = wavelgnth
For bright bands, m is the order = 1,2,3,4
For dark bands, m = 1.5, 2.5, 3.5, 4.5
R = Distance from slit to screen (The indifference pattern)
Y = Distance from central spot to the nth order fringe or fringe width
Thus, here d = mLR/Y
d = 1× 519nm × 4.6 / 5.2mm
d = 0.459 mm
A uniform meter stick is hung at its center from a thin wire. It is twisted and oscillates with a period of 5 s. The meter stick is then sawed off to a length of 0.76 m, rebalanced at its center, and set into oscillation. With what period does it now oscillate?
Answer:
The new time period is [tex]T_2 = 3.8 \ s[/tex]
Explanation:
From the question we are told that
The period of oscillation is [tex]T = 5 \ s[/tex]
The new length is [tex]l_2 = 0.76 \ m[/tex]
Let assume the original length was [tex]l_1 = 1 m[/tex]
Generally the time period is mathematically represented as
[tex]T = 2 \pi \sqrt{ \frac{ I }{ mgh } }[/tex]
Now I is the moment of inertia of the stick which is mathematically represented as
[tex]I = \frac{m * l^2 }{12 }[/tex]
So
[tex]T = 2 \pi \sqrt{ \frac{ m * l^2 }{12 * mgh } }[/tex]
Looking at the above equation we see that
[tex]T \ \ \ \alpha \ \ \ l[/tex]
=> [tex]\frac{ T_2 }{T_1} = \frac{l_2}{l_1}[/tex]
=> [tex]\frac{ T_2}{5} = \frac{0.76}{1}[/tex]
=> [tex]T_2 = 3.8 \ s[/tex]
Consider a series RLC circuit where R=25.0 Ω, C=35.5 μF, and L=0.0940 H, that is driven at a frequency of 70.0 Hz. Determine the phase angle ϕ of the circuit in degrees.
Answer:
137.69°Explanation:
The phase angle of an RLC circuit ϕ is expressed as shoen below;
ϕ = [tex]tan^{-1} \dfrac{X_l-X_c}{R}[/tex]
Xc is the capacitive reactance = 1/2πfC
Xl is the inductive reactance = 2πfL
R is the resistance = 25.0Ω
Given C = 35.5 μF, L = 0.0940 H, and frequency f = 70.0Hz
Xl = 2π * 70*0.0940
Xl = 41.32Ω
For the capacitive reactance;
Xc = 1/2π * 70*35.5*10⁻⁶
Xc = 1/0.0156058
Xc = 64.08Ω
Phase angle ϕ = [tex]tan^{-1} \frac{41.32-64.08}{25} \\\\[/tex]
ϕ = [tex]tan^{-1} \frac{-22.76}{25} \\\\\\\\[/tex]
[tex]\phi = tan^{-1} -0.9104\\\\\phi = -42.31^0[/tex]
Since tan is negative in the 2nd quadrant;
[tex]\phi = 180-42.31^0\\\\\phi = 137.69^0[/tex]
Hence the phase angle ϕ of the circuit in degrees is 137.69°
The phase angle ϕ of the series RLC circuit that is driven at a frequency of 70.0 Hz is ϕ = 137.69°
Phase angle:Given that:
capacitance C = 35.5 μF,
Inductance L = 0.0940 H,
The resistance R = 25.0Ω
and frequency f = 70.0Hz
The capacitive reactance is given by:
Xc = 1/2πfC
Xc = 1/2π × 70 × 35.5× 10⁻⁶
Xc = 1/0.0156058
Xc = 64.08Ω
The inductive reactance is given by:
Xl = 2πfL
Xl = 2π × 70 × 0.0940
Xl = 41.32Ω
The phase angle of an RLC circuit ϕ is given by:
[tex]\phi=tan^{-1}\frac{X_l-X_c}{R}\\\\\phi=tan^{-1}\frac{41.32-64.08}{25}[/tex]
Ф = -42.31°
Since tan is negative in the 2nd quadrant, thus:
ϕ = 180° - 42.31°
ϕ = 137.69°
Learn more about RLC circuit:
https://brainly.com/question/372577?referrer=searchResults
A force of 16.88 N is applied tangentially to a wheel of radius 0.340 m and gives rise to an angular acceleration of 1.20rad / (s ^ 2) . Calculate the rotational inertia of the wheel. A. 2.77 kg - m ^ 2 B. 0.73 kg - m ^ 2 C. 4.41 kg - m ^ 2 O. 4.78 kg - m ^ 2
Given.
force = 16.88 N is
radius = 0.340m
an angular acceleration = 1.20rad/s^2
the formula for torque is
F*r = I*a
where I is moment of inertia
16.88*.34 = I*1.2
I = 4.78Kg-m^2
so rotational inertia I = 4.78Kg-m^2
Without actually calculating any logarithms, determine which of the following intervals the sound intensity level of a sound with intensity 3.66×10^−4W/m^2 falls within?
a. 30 and 40
b. 40 and 50
c. 50 and 60
d. 60 and 70
e. 70 and 80
f. 80 and 90
g. 90 and 100
Answer:
f. 80 and 90
Explanation:
1 x 10⁻¹² W/m² sound intensity falls within 0 sound level
1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level
1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level
1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level
1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level
1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level
1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level
1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level
1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level
1 x 10⁻³ W/m² sound intensity falls within 90 sound level
Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.
f. 80 and 90
Calculate the answers to the appropriate number of significant
12.21 x 9.19 =
a radio antenna emits electromagnetic waves at a frequency of 100 mhz and intensity of what is the photon density
Answer:
photon density = 1.0 × [tex]10^{16}[/tex] photon/m³
Explanation:
given data
frequency f = 100 mhz = 100 × [tex]10^{6}[/tex] Hz
we consider here intensity I = 0.2 W/m²
solution
we take here plank constant is h i.e = 6.626 × [tex]10^{-34}[/tex] s
and take energy density is E
so here
E × C = I
E = [tex]\frac{I}{C}[/tex] ................1
here C = 3 × [tex]10^{8}[/tex] m/s
so photon density is
photon density = [tex]\frac{I}{C} \times \frac{1}{f \times h}[/tex] ...............2
photon density = [tex]\frac{0.2}{3 \times 10^8} \times \frac{1}{100 \times 10^6 \times 6.626 \times 10^{-34} }[/tex]
photon density = 1.0 × [tex]10^{16}[/tex] photon/m³
Two long parallel wires are a center-to-center distance of 1.30 cm apart and carry equal anti-parallel currents of 2.40 A. Find the magnitude of the magnetic field at the point P which is equidistant from the wires. (R = 5.00 cm).
Image is missing, so i have attached it
Answer:
19.04 × 10⁻⁴ T in the +x direction
Explanation:
We are told that the point P which is equidistant from the wires. (R = 5.00 cm). Thus distance from each wire to O is R.
Hence, the magnetic field at P from each wire would be; B = μ₀I/(2πR)
We are given;
I = 2.4 A
R = 5 cm = 0.05 m
μ₀ is a constant = 4π × 10⁻⁷ H/m
B = (4π × 10⁻⁷ × 2.4)/(2π × 0.05)
B = 9.6 × 10⁻⁴ T
To get the direction of the field from each wire, we will use Flemings right hand rule.
From the diagram attached:
We can say the field at P from the top wire will point up/right
Also, the field at P from the bottom wire will point down/right
Thus, by symmetry, the y components will cancel out leaving the two equal x components to act to the right.
If the mid-point between the wires is M, the the angle this mid point line to P makes with either A or B should be same since P is equidistant from both wires.
Let the angle be θ
Thus;
sin(θ) = (1.3/2)/5
θ = sin⁻¹(0.13) = 7.47⁰
The x component of each field would be:
9.6 × 10⁻⁴cos(7.47) = 9.52 × 10⁻⁴ T
Thus, total field = 2 × 9.52 × 10⁻⁴ = 19.04 × 10⁻⁴ T in the +x direction
The magnitude of the magnetic field at the point P will be "9.6 × 10⁻⁴ T".
Magnetic fieldThe region of the environment close to something like a magnetic entity or a current-carrying body wherein this same magnetic forces caused by the body as well as a current might well be sensed.
According to the question,
Current, I = 2.4 A
Radius, R = 5 cm or,
= 0.05 m
Constant, μ₀ = 4π × 10⁻⁷ H/m
We know the relation,
The magnetic field, B = [tex]\frac{\mu_0 I}{2 \pi R}[/tex]
By substituting the values in the above relation, we get
= [tex]\frac{4 \pi\times 10^{-7}\times 2.4}{2 \pi\times 0.05}[/tex]
= 9.6 × 10⁻⁴ T
Thus the above answer is appropriate.
Find out more information about magnetic field here:
https://brainly.com/question/14411049
please i dont understand
A Galilean telescope adjusted for a relaxed eye is 36.2 cm long. If the objective lens has a focal length of 39.5 cm , what is the magnification
Answer:
The magnification is [tex]m = 12[/tex]
Explanation:
From the question we are told that
The object distance is [tex]u = 36.2 \ cm[/tex]
The focal length is [tex]v = 39.5 \ cm[/tex]
From the lens equation we have that
[tex]\frac{1}{f} = \frac{1}{u} + \frac{1}{v}[/tex]
=> [tex]\frac{1}{v} = \frac{1}{f} - \frac{1}{u}[/tex]
substituting values
[tex]\frac{1}{v} = \frac{1}{39.5} - \frac{1}{36.2}[/tex]
[tex]\frac{1}{v} = -0.0023[/tex]
=> [tex]v = \frac{1}{0.0023}[/tex]
=> [tex]v =-433.3 \ cm[/tex]
The magnification is mathematically represented as
[tex]m =- \frac{v}{u}[/tex]
substituting values
[tex]m =- \frac{-433.3}{36.2}[/tex]
[tex]m = 12[/tex]
Two long, parallel wires are separated by a distance of 2.60 cm. The force per unit length that each wire exerts on the other is 4.30×10^−5 N/m, and the wires repel each other. The current in one wire is 0.520 A.Required:a. What is the current in the second wire? b. Are the two currents in the same direction or in opposite directions?
Answer:
10.75 A
The current is in opposite direction since it causes a repulsion force between the wires
Explanation:
Force per unit length on the wires = 4.30×10^−5 N/m
distance between wires = 2.6 cm = 0.026 m
current through one wire = 0.52 A
current on the other wire = ?
Recall that the force per unit length of two wires conducting and lying parallel and close to each other is given as
[tex]F/l[/tex] = [tex]\frac{u_{0}I_{1} I_{2} }{2\pi r }[/tex]
where [tex]F/l[/tex] is the force per unit length on the wires
[tex]u_{0}[/tex] = permeability of vacuum = 4π × 10^−7 T-m/A
[tex]I_{1}[/tex] = current on the first wire = 0.520 A
[tex]I_{2}[/tex] = current on the other wire = ?
r = the distance between the two wire = 0.026 m
substituting the value into the equation, we have
4.30×10^−5 = [tex]\frac{4\pi *10^{-7}*0.520*I_{2} }{2\pi *0.026}[/tex] = [tex]\frac{ 2*10^{-7}*0.520*I_{2} }{0.026}[/tex]
4.30×10^−5 = 4 x 10^-6 [tex]I_{2}[/tex]
[tex]I_{2}[/tex] = (4.30×10^-5)/(4 x 10^-6) = 10.75 A
The current is in opposite direction since it causes a repulsion force between the wires.