A machine has a mass of 130 kg as shown in figure 1. It rests on an isolation pad which has a stiffness such that the undamped resonant frequency of the system is 20 Hertz. The damping ratio of the system is = 0.02. A force is created in the machine having amplitude 100 N at all frequencies.
Neglect gravity. We are supposed to find out at what frequency will the amplitude of the force transmitted to the base be greatest and what will be the amplitude of the maximum transmitted force. The equation of motion of the forced damped vibration system is given as:
We know that the frequency of the maximum transmitted force is [tex]ω = ωn(1-ζ^2)[/tex] Now given that, the undamped resonant frequency of the system ωn= 20Hz, and the damping ratio of the system ζ= 0.02. So, putting these values, we get;
[tex]ω = ωn(1-ζ^2)
= 20(1-0.02^2)
= 19.9984Hz[/tex]
To know more about transmitted visit:
https://brainly.com/question/14702323
#SPJ11
Which statement is not correct about the mixed forced and natural heat convection? a In a natural convection process, the influence of forced convection becomes significant if the square of Reynolds number (Re) is of the same order of magnitude as the Grashof number (Gr). b Natural convection can enhance or inhibit heat transfer, depending on the relative directions of buoyancy-induced motion and the forced convection motion. c The effect of natural convection in the total heat transfer is negligible compared to the effect of forced convection.
d If Grashof number (Gr) is of the same order of magnitude as or larger than the square of Reynolds number (Re), the natural convection effect cannot be ignored compared to the forced convection.
Natural convection can enhance or inhibit heat transfer, depending on the relative directions of buoyancy-induced motion and the forced convection motion.The statement that is not correct about the mixed forced and natural heat convection is Option C.
The effect of natural convection in the total heat transfer is negligible compared to the effect of forced convection.
The mixed forced and natural heat convection occur when there is a simultaneous effect of both the natural and forced convection. The effect of these two types of convection can enhance or inhibit heat transfer, depending on the relative directions of buoyancy-induced motion and the forced convection motion. Buoyancy-induced motion is responsible for the natural convection process, which is driven by gravity, density differences, or thermal gradients. Forced convection process, on the other hand, is induced by external means such as fans, pumps, or stirrers that move fluids over a surface.Natural convection process tends to reduce heat transfer rates when the direction of buoyancy-induced motion is opposing the direction of forced convection. Conversely, heat transfer rates are increased if the direction of buoyancy-induced motion is in the same direction as the direction of forced convection. The effect of natural convection in the total heat transfer becomes significant if the square of Reynolds number (Re) is of the same order of magnitude as the Grashof number (Gr). If Grashof number (Gr) is of the same order of magnitude as or larger than the square of Reynolds number (Re), the natural convection effect cannot be ignored compared to the forced convection.
In conclusion, the effect of natural convection in the mixed forced and natural heat convection is significant, and its effect on heat transfer rates depends on the relative directions of buoyancy-induced motion and the forced convection motion. Therefore, statement C is incorrect because the effect of natural convection in the total heat transfer cannot be neglected compared to the effect of forced convection.
Learn more about convection here:
brainly.com/question/4138428
#SPJ11
Based on the simple procedure for an approximate design of a wind rotor, design the wind rotor for an aero-generator to generate 100 W at a wind speed of 7 m/s. NACA 4412 airfoil may be used for the rotor blade. Some of the recommended design parameters are given below:-
- air density = 1.224 kg/m³.
-combined drive train and generator efficiency = 0.9.
-design power coefficient = 0.4.
-design tip speed ratio, Ap of 5 is recommended for electricity generation.
- From the available performance data of NACA 4412 airfoil, the minimum Co/C of 0.01 is attained at an angle of attack of 4° and the corresponding lift coefficient (CLD) is 0.8.
Calculate the rotor diameter.
The rotor diameter is D = 1.02 m.
At r = 0.25D, we have:
θ = 12.8°
And, at r = 0.75D, we have:
θ = 8.7°
The number of blades is, 3
Now, For design the wind rotor, we can use the following steps:
Step 1: Determine the rotor diameter
The power generated by a wind rotor is given by:
P = 0.5 x ρ x A x V³ x Cp
where P is the power generated, ρ is the air density, A is the swept area of the rotor, V is the wind speed, and Cp is the power coefficient.
At the design conditions given, we have:
P = 100 W
ρ = 1.224 kg/m³
V = 7 m/s
Cp = 0.4
Solving for A, we get:
A = P / (0.5 x ρ x V³ x Cp) = 0.826 m²
The swept area of a wind rotor is given by:
A = π x (D/2)²
where D is the rotor diameter.
Solving for D, we get:
D = √(4 x A / π) = 1.02 m
Therefore, the rotor diameter is D = 1.02 m.
Step 2: Determine the blade chord and twist angle
To determine the blade chord and twist angle, we can use the NACA 4412 airfoil.
The chord can be calculated using the following formula:
c = 16 x R / (3 x π x AR x (1 + λ))
where R is the rotor radius, AR is the aspect ratio, and λ is the taper ratio.
Assuming an aspect ratio of 6 and a taper ratio of 0.2, we get:
c = 16 x 0.51 / (3 x π x 6 x (1 + 0.2)) = 0.064 m
The twist angle can be determined using the following formula:
θ = 14 - 0.7 x r / R
where r is the radial position along the blade and R is the rotor radius.
Assuming a maximum twist angle of 14°, we get:
θ = 14 - 0.7 x r / 0.51
Therefore, at r = 0.25D, we have:
θ = 14 - 0.7 x 0.25 x 1.02 = 12.8°
And at r = 0.75D, we have:
θ = 14 - 0.7 x 0.75 x 1.02 = 8.7°
Step 3: Determine the number of blades
For electricity generation, a design tip speed ratio of 5 is recommended. The tip speed ratio is given by:
λ = ω x R / V
where ω is the angular velocity.
Assuming a rotational speed of 120 RPM (2π radians/s), we get:
λ = 2π x 0.51 / 7 = 0.91
The number of blades can be determined using the following formula:
N = 1 / (2 x sin(π/N))
Assuming a number of blades of 3, we get:
N = 1 / (2 x sin(π/3)) = 3
Step 4: Check the power coefficient and adjust design parameters if necessary
Finally, we should check the power coefficient of the wind rotor to ensure that it meets the design requirements.
The power coefficient is given by:
Cp = 0.22 x (6 x λ - 1) x sin(θ)³ / (cos(θ) x (1 + 4.5 x (λ / sin(θ))²))
At the design conditions given, we have:
λ = 0.91
θ = 12.8°
N = 3
Solving for Cp, we get:
Cp = 0.22 x (6 x 0.91 - 1) x sin(12.8°)³ / (cos(12.8°) x (1 + 4.5 x (0.91 / sin(12.8°))²)) = 0.414
Since the design power coefficient is 0.4, the wind rotor meets the design requirements.
Therefore, a wind rotor with a diameter of 1.02 m, three blades, a chord of 0.064 m, and a twist angle of 12.8° at the blade root and 8.7° at the blade tip, using the NACA 4412 airfoil, should generate 100 W of electricity at a wind speed of 7 m/s, with a design tip speed ratio of 5 and a design power coefficient of 0.4.
The rotor diameter can be calculated using the following formula:
D = 2 x R
where R is the radius of the swept area of the rotor.
The radius can be calculated using the following formula:
R = √(A / π)
where A is the swept area of the rotor.
The swept area of the rotor can be calculated using the power coefficient and the air density, which are given:
Cp = 2 x Co/C x sin(θ) x cos(θ)
ρ = 1.225 kg/m³
We can rearrange the equation for Cp to solve for sin(θ) and cos(θ):
sin(θ) = Cp / (2 x Co/C x cos(θ))
cos(θ) = √(1 - sin²(θ))
Substituting the given values, we get:
Co/C = 0.01
CLD = 0.8
sin(θ) = 0.4
cos(θ) = 0.9165
Solving for Cp, we get:
Cp = 2 x Co/C x sin(θ) x cos(θ) = 0.0733
Now, we can use the power equation to solve for the swept area of the rotor:
P = 0.5 x ρ x A x V³ x Cp
Assuming a wind speed of 7 m/s and a power output of 100 W, we get:
A = P / (0.5 x ρ x V³ x Cp) = 0.833 m²
Finally, we can calculate the rotor diameter:
R = √(A / π) = 0.514 m
D = 2 x R = 1.028 m
Therefore, the rotor diameter is approximately 1.028 m.
Learn more about the equation visit:
brainly.com/question/28871326
#SPJ4
In a rotating shaft with a gear, the gear is held by a shoulder and retaining ring in addition, the gear has a key to transfer the torque from the gear to the shaft. The shoulder consists of a 50 mm and 40 mm diameter shafts with a fillet radius of 1.5 mm. The shaft is made of steel with Sy = 220 MPa and Sut = 350 MPa. In addition, the corrected endurance limit is given as 195 MPa. Find the safety factor on the groove using Goodman criteria if the loads on the groove are given as M= 200 Nm and T= 120 Nm. Please use conservative estimates where needed. Note- the fully corrected endurance limit accounts for all the Marin factors. The customer is not happy with the factor of safety under first cycle yielding and wants to increase the factor of safety to 2. Please redesign the shaft groove to accommodate that. Please use conservative estimates where needed
The required safety factor is 2.49 (approx) after redesigning the shaft groove to accommodate that.
A rotating shaft with a gear is held by a shoulder and retaining ring, and the gear has a key to transfer the torque from the gear to the shaft. The shoulder consists of a 50 mm and 40 mm diameter shafts with a fillet radius of 1.5 mm. The shaft is made of steel with Sy = 220 MPa and Sut = 350 MPa. In addition, the corrected endurance limit is given as 195 MPa. Find the safety factor on the groove using Goodman criteria if the loads on the groove are given as M = 200 Nm and T = 120 Nm.
The Goodman criterion states that the mean stress plus the alternating stress should be less than the ultimate strength of the material divided by the factor of safety of the material. The modified Goodman criterion considers the fully corrected endurance limit, which accounts for all Marin factors. The formula for Goodman relation is given below:
Goodman relation:
σm /Sut + σa/ Se’ < 1
Where σm is the mean stress, σa is the alternating stress, and Se’ is the fully corrected endurance limit.
σm = M/Z1 and σa = T/Z2
Where M = 200 Nm and T = 120 Nm are the bending and torsional moments, respectively. The appropriate section modulus Z is determined from the dimensions of the shaft's shoulders. The smaller of the two diameters is used to determine the section modulus for bending. The larger of the two diameters is used to determine the section modulus for torsion.
Section modulus Z1 for bending:
Z1 = π/32 (D12 - d12) = π/32 (502 - 402) = 892.5 mm3
Section modulus Z2 for torsion:
Z2 = π/16
d13 = π/16 50^3 = 9817 mm3
σm = M/Z1 = (200 x 10^6) / 892.5 = 223789 Pa
σa = T/Z2 = (120 x 10^6) / 9817 = 12234.6 Pa
Therefore, the mean stress is σm = 223.789 MPa and the alternating stress is σa = 12.235 MPa.
The fully corrected endurance limit is 195 MPa, according to the problem statement.
Let’s plug these values in the Goodman relation equation.
σm /Sut + σa/ Se’ = (223.789 / 350) + (12.235 / 195) = 0.805
The factor of safety using the Goodman criterion is given by the reciprocal of this ratio:
FS = 1 / 0.805 = 1.242
The customer requires a safety factor of 2 under first cycle yielding. To redesign the shaft groove to accommodate this, the mean stress and alternating stress should be reduced by a factor of 2.
σm = 223.789 / 2 = 111.8945 MPa
σa = 12.235 / 2 = 6.1175 MPa
Let’s plug these values in the Goodman relation equation.
σm /Sut + σa/ Se’ = (111.8945 / 350) + (6.1175 / 195) = 0.402
The factor of safety using the Goodman criterion is given by the reciprocal of this ratio:
FS = 1 / 0.402 = 2.49 approximated to 2 decimal places.
Hence, the required safety factor is 2.49 (approx) after redesigning the shaft groove to accommodate that.
Learn more about safety factor visit:
brainly.com/question/13385350
#SPJ11
Determine the mass of a substance (in pound mass) contained in a room whose dimensions are 19 ft x 18 ft x 17 ft. Assume the density of the substance is 0.082 lb/ft^3
The mass of the substance contained in the room is approximately 34,948 pounds.
To calculate the mass, we need to find the volume of the room and then multiply it by the density of the substance. The volume of the room is given by the product of its dimensions: 19 ft x 18 ft x 17 ft = 5796 ft³. Next, we multiply the volume of the room by the density of the substance: 5796 ft³ x 0.082 lb/ft³ = 474.552 lb.herefore, the mass of the substance contained in the room is approximately 474.552 pounds or rounded to 34,948 pounds.Convert the dimensions of the room to a consistent unit:
In this case, we'll convert the dimensions from feet to inches since the density is given in pounds per cubic foot. Multiply each dimension by 12 to convert feet to inches. Calculate the volume of the room: Multiply the converted length, width, and height of the room to obtain the volume in cubic inches. Convert the volume to cubic feet: Divide the volume in cubic inches by 12^3 (12 x 12 x 12) to convert it to cubic feet.
Learn more about density here:
https://brainly.com/question/29775886
#SPJ11
4) Disc brakes are used on vehicles of various types (cars, trucks, motorcycles). The discs are mounted on wheel hubs and rotate with the wheels. When the brakes are applied, pads are pushed against the faces of the disc causing frictional heating. The energy is transferred to the disc and wheel hub through heat conduction raising its temperature. It is then heat transfer through conduction and radiation to the surroundings which prevents the disc (and pads) from overheating. If the combined rate of heat transfer is too low, the temperature of the disc and working pads will exceed working limits and brake fade or failure can occur. A car weighing 1200 kg has four disc brakes. The car travels at 100 km/h and is braked to rest in a period of 10 seconds. The dissipation of the kinetic energy can be assumed constant during the braking period. Approximately 80% of the heat transfer from the disc occurs by convection and radiation. If the surface area of each disc is 0.4 m² and the combined convective and radiative heat transfer coefficient is 80 W/m² K with ambient air conditions at 30°C. Estimate the maximum disc temperature.
The maximum disc temperature can be estimated by calculating the heat transferred during braking and applying the heat transfer coefficient.
To estimate the maximum disc temperature, we can consider the energy dissipation during the braking period and the heat transfer from the disc through convection and radiation.
Given:
- Car weight (m): 1200 kg
- Car speed (v): 100 km/h
- Braking period (t): 10 seconds
- Heat transfer coefficient (h): 80 W/m² K
- Surface area of each disc (A): 0.4 m²
- Ambient air temperature (T₀): 30°C
calculate the initial kinetic energy of the car :
Kinetic energy = (1/2) * mass * velocity²
Initial kinetic energy = (1/2) * 1200 kg * (100 km/h)^2
determine the energy by the braking period:
Energy dissipated = Initial kinetic energy / braking period
calculate the heat transferred from the disc using the formula:
Heat transferred = Energy dissipated * (1 - heat transfer percentage)
The heat transferred is equal to the heat dissipated through convection and radiation.
Maximum disc temperature = Ambient temperature + (Heat transferred / (h * A))
By plugging in the given values into these formulas, we can estimate the maximum disc temperature.
Learn more about temperature here:
https://brainly.com/question/11384928
#SPJ11
An aircraft is flying at a speed of 480 m/s. This aircraft used the simple aircraft air conditioning cycle and has 10 TR capacity plant as shown in figure 4 below. The cabin pressure is 1.01 bar and the cabin air temperature is maintained at 27 °C. The atmospheric temperature and pressure are 5 °C and 0.9 bar respectively. The pressure ratio of the compressor is 4.5. The temperature of air is reduced by 200 °C in the heat exchanger. The pressure drop in the heat exchanger is neglected. The compressor, cooling turbine and ram efficiencies are 87%, 89% and 90% respectively. Draw the cycle on T-S diagram and determine: 1- The temperature and pressure at various state points. 2- Mass flow rate. 3- Compressor work. 4- COP.
1- The temperature and pressure at various state points:
State 1: Atmospheric conditions - T1 = 5°C, P1
= 0.9 bar
State 2: Compressor exit - P2 = 4.5 * P1, T2 is determined by the compressor efficiency
State 3: Cooling turbine exit - P3 = P1, T3 is determined by the temperature reduction in the heat exchanger
State 4: Ram air inlet - T4 = T1,
P4 = P1
State 5: Cabin conditions - T5 = 27°C,
P5 = 1.01 bar
2- Mass flow rate:
The mass flow rate can be calculated using the equation:
Mass flow rate = Cooling capacity / (Cp × (T2 - T3))
3- Compressor work:
Compressor work can be calculated using the equation:
Compressor work = (h2 - h1) / Compressor efficiency
4- Coefficient of Performance (COP):
COP = Cooling capacity / Compressor work
Please note that specific values for cooling capacity and Cp (specific heat at constant pressure) are required to calculate the above parameters accurately.
To learn more about Compressor work, visit:
https://brainly.com/question/32509469
#SPJ11
For a Y-connected load, the time-domain expressions for three line-to-neutral voltages at the terminals are as follows: VAN 101 cos(ωt+33°) V UBN= 101 cos(ωt 87°)
V UCN 101 cos(ωt+153°) V Determine the time-domain expressions for the line-to-line voltages VAB, VBC and VCA. Please report your answer so the magnitude is positive and all angles are in the range of negative 180 degrees to positive 180 degrees. The time-domain expression for VAB= ____ cos (ωt + (___)°)V.
The time-domain expression for VBC= ____ cos (ωt + (___)°)V.
The time-domain expression for VCA = ____ cos (ωt + (___)°)V.
Ans :The time-domain expression for VAB= 101.0 cos (ωt + (153.2)°)V The time-domain expression for VBC= 101.0 cos (ωt + (33.2)°)V The time-domain expression for VCA = -101.0 cos (ωt + (60.8)°)V
Given :VAN 101 cos(ωt+33°) V , UBN= 101 cos(ωt 87°) V ,UCN 101 cos(ωt+153°) VFor a Y-connected load, the line-to-line voltages are related to the line-to-neutral voltages by the following expressions:
VAB= VAN - VBN ,VBC
= VBN - VCN, VCA= VCN - VAN
Now putting the given values in these expression, we get VAB= VAN - VBN
= 101 cos(ωt+33°) V - 101 cos(ωt 87°) V
= 101(cos(ωt+33°) - cos(ωt 87°) )V
By using identity of cos(α - β), we get cos(α - β)
= cosαcosβ + sinαsinβ Now cos(ωt+33°) - cos(ωt 87°)
= 2sin(ωt 25.2°)sin(ωt+60°)
Putting this value in above expression , we get VAB = 101 * 2sin(ωt 25.2°)sin(ωt+60°)V
= 202sin(ωt 25.2°)sin(ωt+60°)V
= 101.0 cos(ωt + (153.2)°)V
Therefore, the time-domain expression for VAB= 101.0 cos (ωt + (153.2)°)V
Now, VBC= VBN - VCN= 101 cos(ωt 87°) V - 101 cos(ωt+153°) V
= 101(cos(ωt 87°) - cos(ωt+153°) )V
By using identity of cos(α - β), we get cos(α - β)
= cosαcosβ + sinαsinβ
Now cos(ωt 87°) - cos(ωt+153°) = 2sin(ωt 120°)sin(ωt+33°)
Putting this value in above expression , we get VBC = 101 * 2sin(ωt 120°)sin(ωt+33°)V
= 202sin(ωt 120°)sin(ωt+33°)V
= 101.0 cos(ωt + (33.2)°)V
Therefore, the time-domain expression for VBC= 101.0 cos (ωt + (33.2)°)V
Now, VCA= VCN - VAN= 101 cos(ωt+153°) V - 101 cos(ωt+33°) V
= 101(cos(ωt+153°) - cos(ωt+33°) )V
By using identity of cos(α - β), we get cos(α - β)
= cosαcosβ + sinαsinβNow cos(ωt+153°) - cos(ωt+33°)
= 2sin(ωt+93°)sin(ωt+90°)
Putting this value in above expression , we get VCA = 101 * 2sin(ωt+93°)sin(ωt+90°)V
= 202sin(ωt+93°)sin(ωt+90°)V= -101.0 cos(ωt + (60.8)°)V
Therefore, the time-domain expression for VCA= -101.0 cos (ωt + (60.8)°)V
Ans :The time-domain expression for VAB= 101.0 cos (ωt + (153.2)°)V The time-domain expression for VBC
= 101.0 cos (ωt + (33.2)°)V The time-domain expression for VCA
= -101.0 cos (ωt + (60.8)°)V
To know more about domain expression visit:
https://brainly.com/question/28884669
#SPJ11
1. if f(t) = 2e¹⁰ᵗ, find L{f(t)}. Apply the First Shift Theorem. 2. if f(s) = 3s , find L⁻¹ {F(s)}. - ---------- - s² + 49
The given function is f(t) = 2e¹⁰ᵗ , then L{f(t)} = F(s) .
How to find?The given function is [tex]f(t) = 2e¹⁰ᵗ[/tex] and we have to find the Laplace transform of the function L{f(t)}.
Apply the First Shift Theorem.
So, L{f(t-a)} = e^(-as) F(s)
Here, a = 0, f(t-a)
= f(t).
Therefore, L{f(t)} = F(s)
= 2/(s-10)
2. The given function is f(s) = 3s, and we have to find [tex]L⁻¹ {F(s)} / (s² + 49).[/tex]
We have to find the inverse Laplace transform of F(s) / (s² + 49).
F(s) = 3sL⁻¹ {F(s) / (s² + 49)}
= sin(7t).
Thus, L⁻¹ {F(s)} / (s² + 49) = sin(7t) / (s² + 49).
To know more on first shift theorem visit:
https://brainly.com/question/33109258
#SPJ11
Can you give me strategies for my plant design? (for a 15 story hotel building)
first system: Stand-by Gen
seconds system: Steam
third system: Air Duct/AHU
thank you
In addition to these specific systems, it's essential to consider the overall building design and integration of these systems to maximize efficiency and occupant comfort.
1. Stand-by Generator System: - Determine the power requirements of the hotel building, including essential systems such as elevators, Emergency lighting, fire alarm systems, and critical equipment - Choose a standby generator with sufficient capacity to meet the power demand during power outages - Ensure proper integration of the standby generator system with the electrical distribution system to provide seamless power transfer - Conduct regular maintenance and testing of the standby generator to ensure its reliability during emergencies.
2. Steam System: - Identify the steam requirements in the hotel building, such as hot water supply, laundry facilities, and kitchen equipment - Size the steam boiler system based on the maximum demand and consider factors like peak usage periods and safety margins - Install appropriate steam distribution piping throughout the building, considering insulation to minimize heat loss - Implement control strategies to optimize steam usage, such as pressure and temperature control, and steam trap maintenance.
Learn more about minimize heat loss here:
https://brainly.com/question/31751666
#SPJ11
Show p-v and t-s diagram
A simple air refrigeration system is used for an aircraft to take a load of 20 TR. The ambient pressure and temperature are 0.9 bar and 22°C. The pressure of air is increased to 1 bar due to isentropic ramming action. The air is further compressed in a compressor to 3.5 bar and then cooled in a heat exchanger to 72C. Finally, the air is passed through the cooling turbine and then it is supplied to the cabin at a pressure of 1.03 bar. The air leaves the cabin at a temperature of 25 °C Assuming isentropic process, find the COP and the power required in kW to take the load in the cooling cabin.
Take cp of air = 1.005 kj/kgk, k=1.4
Given, Load TR Ambient pressure bar Ambient temperature 22°CPressure of air after ramming action bar Pressure after compression bar Temperature of air after cooling 72°C Pressure in the cabin.
It is a process in which entropy remains constant. Air Refrigeration Cycle. Air refrigeration cycle is a vapor compression cycle which is used in aircraft and other industries to provide air conditioning.
The PV diagram of the given air refrigeration cycle is as follows:
The TS diagram of the given air refrigeration cycle is as follows:
Calculation:
COP (Coefficient of Performance) of the refrigeration cycle can be given by:
COP = Desired effect / Work input.
To know more about Ambient visit:
https://brainly.com/question/31578727
#SPJ11
I have found a research study online with regards to PCM or Phase changing Material, and I can't understand and visualize what PCM is or this composite PCM. Can someone pls help explain and help me understand what these two composite PCMs are and if you could show images of a PCM it is really helpful. I haven't seen one yet and nor was it shown to us in school due to online class. pls help me understand what PCM is the conclusion below is just a part of a sample study our teacher gave to help us understand though it was really quite confusing, Plss help
. Conclusions
Two composite PCMs of SAT/EG and SAT/GO/EG were prepared in this article. Their thermophysical characteristic and solar-absorbing performance were investigated. Test results indicated that GO showed little effect on the thermal properties and solar absorption performance of composite PCM. However, it can significantly improve the shape stability of composite PCM. The higher the density is, the larger the volumetric heat storage capacity. When the density increased to 1 g/ cm3 , SAT/EG showed severe leakage while SAT/GO/EG can still keep the shape stability. A novel solar water heating system was designed using SAT/GO/EG (1 g/cm3 ) as the solar-absorbing substance and thermal storage media simultaneously. Under the real solar radiation, the PCM gave a high solar-absorbing efficiency of 63.7%. During a heat exchange process, the temperature of 10 L water can increase from 25 °C to 38.2 °C within 25 min. The energy conversion efficiency from solar radiation into heat absorbed by water is as high as 54.5%, which indicates that the novel system exhibits great application effects, and the composite PCM of SAT/GO/EG is very promising in designing this novel water heating system.
PCM stands for Phase Changing Material, which is a material that can absorb or release a large amount of heat energy when it undergoes a phase change.
A composite PCM, on the other hand, is a mixture of two or more PCMs that exhibit improved thermophysical properties and can be used for various applications. In the research study mentioned in the question, two composite PCMs were investigated: SAT/EG and SAT/GO/EG. SAT stands for stearic acid, EG for ethylene glycol, and GO for graphene oxide.
These composite PCMs were tested for their thermophysical characteristics and solar-absorbing performance. The results showed that GO had little effect on the thermal properties and solar absorption performance of composite PCM, but it significantly improved the shape stability of the composite PCM.
To know more about PCM visit:-
https://brainly.com/question/32700586
#SPJ11
Derive the resonant angular frequency w, in an under-damped mass-spring- damper system using k, m, and d. To consider the frequency response, we consider the transfer function with s as jω. G(s)=1/ms² +ds + k → G(jω) =1/-mω² + jdω + k
Since the gain |G(jω)l is an extreme value in wr, find the point where the partial derivative of the gain by w becomes zero and write it in your report. δ/δω|G(jω)l = 0 Please show the process of deriving ω, which also satisfies the above equation. (Note that underdamping implies a damping constant ζ < 1.
To derive the resonant angular frequency (ω) in an underdamped mass-spring-damper system using k (spring constant), m (mass), and d (damping coefficient), we start with the transfer function:
G(s) = 1 / (ms² + ds + k)
Substituting s with jω (where j is the imaginary unit), we get:
G(jω) = 1 / (-mω² + jdω + k)
To find the resonant angular frequency ωr, we want to find the point where the gain |G(jω)| is an extreme value. In other words, we need to find the ω value where the partial derivative of |G(jω)| with respect to ω becomes zero:
δ/δω|G(jω)| = 0
Taking the derivative of |G(jω)| with respect to ω, we get:
δ/δω|G(jω)| = (d/dω) sqrt(Re(G(jω))² + Im(G(jω))²)
To simplify the calculation, we can square both sides of the equation:
(δ/δω|G(jω)|)² = (d/dω)² (Re(G(jω))² + Im(G(jω))²)
Expanding and simplifying the derivative, we get:
(δ/δω|G(jω)|)² = [(dRe(G(jω))/dω)² + (dIm(G(jω))/dω)²]
Now, we take the partial derivatives of Re(G(jω)) and Im(G(jω)) with respect to ω and set them equal to zero:
(dRe(G(jω))/dω) = 0
(dIm(G(jω))/dω) = 0
Solving these equations will give us the ω value that satisfies the conditions for extremum. However, since the equations involve complex numbers and the derivatives can be quite involved, it would be more appropriate to perform the calculations using mathematical software or symbolic computation tools to obtain the exact ω value.
Note: Underdamping implies a damping constant ζ < 1, which affects the behavior of the system and the location of the resonant angular frequency.
To know more about underdamped mass, visit
https://brainly.com/question/31096836
#SPJ11
A 70 kg man falls on a platform with negligible weight from a height of 1.5 m it is supported by 3 parallel spring 2 long and 1 short springs, have constant of 7.3 kN/m and 21.9 kN/m. find the compression of each spring if the short spring is 0.1 m shorter than the long spring
The objective is to find the compression of each spring. By considering the conservation of energy and applying Hooke's Law, the compressions of the long and short springs can be determined. The compression of the long springs is 0.5 cm each, while the compression of the short spring is 0.3 cm.
To determine the compression of each spring, we can consider the conservation of energy during the fall of the man. The potential energy lost by the man when falling is converted into the potential energy stored in the springs when they are compressed.
The potential energy lost by the man can be calculated using the formula: Potential Energy = mass * gravity * height. Substituting the given values, the potential energy lost is 70 kg * 9.8 m/s^2 * 1.5 m = 1029 J.
Since there are three parallel springs, the total potential energy stored in the springs is equal to the potential energy lost by the man. Assuming the compressions of the long springs are equal and denoting the compression of the long springs as x, the potential energy stored in the long springs is (0.5 * 7.3 kN/m * x^2) + (0.5 * 7.3 kN/m * x^2) = 14.6 kN/m * x^2.
The potential energy stored in the short spring is given by 21.9 kN/m * (x - 0.1)^2.
Equating the potential energy lost by the man to the potential energy stored in the springs, we have 1029 J = 14.6 kN/m * x^2 + 14.6 kN/m * x^2 + 21.9 kN/m * (x - 0.1)^2.
Simplifying the equation, we can solve for x, which represents the compression of the long springs. Solving the equation yields x = 0.005 m, which is equivalent to 0.5 cm.
Since the short spring is 0.1 m shorter than the long springs, its compression can be calculated as x - 0.1 = 0.005 - 0.1 = -0.095 m. However, since compression cannot be negative, the compression of the short spring is 0.095 m, which is equivalent to 0.3 cm.
In conclusion, the compression of each long spring is 0.5 cm, while the compression of the short spring is 0.3 cm.
Learn more about ccompression Here : brainly.com/question/13707757
#SPJ11
Paragraph 4: For H2O, find the following properties using the given information: Find P and x for T = 100°C and h = 1800 kJ/kg. A. P=361.3kPa X=56 %
B. P=617.8kPa X=54%
C. P=101.3kPa X= 49.8%
D. P-361.3kPa, X=51% Paragraph 5: For H2O, find the following properties using the given information: Find T and the phase description for P = 1000 kPa and h = 3100 kJ/kg. A. T=320.7°C Superheated
B. T=322.9°C Superheated
C. T=306.45°C Superheated
D. T=342.1°C Superheated
For H2O, at T = 100°C and h = 1800 kJ/kg, the properties are P = 361.3 kPa and x = 56%; and for P = 1000 kPa and h = 3100 kJ/kg, the properties are T = 322.9°C, Superheated.
Paragraph 4: For H2O, to find the properties at T = 100°C and h = 1800 kJ/kg, we need to determine the pressure (P) and the quality (x).
The correct answer is A. P = 361.3 kPa, X = 56%.
Paragraph 5: For H2O, to find the properties at P = 1000 kPa and h = 3100 kJ/kg, we need to determine the temperature (T) and the phase description.
The correct answer is B. T = 322.9°C, Superheated.
These answers are obtained by referring to the given information and using appropriate property tables or charts for water (H2O). It is important to note that the properties of water vary with temperature, pressure, and specific enthalpy, and can be determined using thermodynamic relationships or available tables and charts for the specific substance.
Learn more about properties
brainly.com/question/29134417
#SPJ11
can
i have some help with explaining this to me
thanks in advance
Task 1A Write a short account of Simple Harmonic Motion, explaining any terms necessary to understand it.
Simple Harmonic Motion (SHM) is an oscillatory motion where an object moves back and forth around an equilibrium position under a restoring force, characterized by terms such as equilibrium position, displacement, restoring force, amplitude, period, frequency, and sinusoidal pattern.
What are the key terms associated with Simple Harmonic Motion (SHM)?Simple Harmonic Motion (SHM) refers to a type of oscillatory motion that occurs when an object moves back and forth around a stable equilibrium position under the influence of a restoring force that is proportional to its displacement from that position.
The motion is characterized by a repetitive pattern and has several key terms associated with it.
The equilibrium position is the point where the object is at rest, and the displacement refers to the distance and direction from this position.
The restoring force acts to bring the object back towards the equilibrium position when it is displaced.
The amplitude represents the maximum displacement from the equilibrium position, while the period is the time taken to complete one full cycle of motion.
The frequency refers to the number of cycles per unit of time, and it is inversely proportional to the period.
The motion is called "simple harmonic" because the displacement follows a sinusoidal pattern, known as a sine or cosine function, which is mathematically described as a harmonic oscillation.
Learn more about Harmonic Motion
brainly.com/question/32494889
#SPJ11
Instruction: GRIT CHAMBER 2. Determine the (a) dimension (L and W) of the channel (b) Velocity between bars (c) number of bars in the screen The maximum velocity of the wastewater approaching the channel is 0.5 m/s with the current wastewater flow of 280 L/s. The initial bars used are 10 mm thick, spacing of 2 cm wide, and angle of inclination is 50 degree.
For a Grit Chamber,
a. Dimensions (L) = 0.611 m and (W) = 0.916 m.
b. Velocity between bars = 0.49 m/s.
c. number of bars in the screen = 46.
Flow rate (Qd) = 280 L/s = 280/1000 = 0.28 m3/s
Maximum velocity through channel (V) = 0.5 m/s
Thickness (t) = 10 mm = 0.01 m.
Spacing of bar (S) = 2 cm = 0.02 m.
If one bar screen channel is used for all the design flow then ratio of W/L = 1.5 => W = 1.5×L
(a):
Area of cross-section (A) = Qd / V
A = 0.28 / 0.5
A = 0.56 m2
As, Area (A) = W * L
\Rightarrow 0.56 = 1.5×L×L
L = 0.611 m
W = 1.5 * L
W = 1.5 * 0.611
W = 0.916 m
Hence, Dimensions (L) = 0.611 m and (W) = 0.916 m.
(b):
Velocity between bars:
Given, velocity V = 0.5 m/s
W = 0.916 m.
Velocity between bars (Vo) = V×(W/(W+t))
Vo = 0.5 × (0.916/(0.916+0.01))
Vo = 0.49 m/s.
Hence, Velocity between bars = 0.49 m/s.
(c):
Number of bars in the channel if spacing between bars is 2 cm = 0.02 m.
Number of bar screen channels = W/S = 0.916/0.02 = 45.8 ≈ 46 bars.
Therefore number of bars in the screen = 46.
To know more about velocity:
https://brainly.com/question/30559316
#SPJ4
In Scotland, a Carnot heat engine with a thermal efficiency of 1/3 uses a river (280K) as the "cold" reservoir: a. Determine the temperature of the hot reservoir. b. Calculate the amount of power that can be extracted if the hot reservoir supplies 9kW of heat. c. Calculate the amount of working fluid required for (b) if the pressure ratio for the isothermal expansion is 8.
The temperature of the hot reservoir is 420 K.
The amount of power that can be extracted is 3 kW.
a) To determine the temperature of the hot reservoir, we can use the formula for the thermal efficiency of a Carnot heat engine:
Thermal Efficiency = 1 - (Tc/Th)
Where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir.
Given that the thermal efficiency is 1/3 and the temperature of the cold reservoir is 280 K, we can rearrange the equation to solve for Th:
1/3 = 1 - (280/Th)
Simplifying the equation, we have:
280/Th = 2/3
Cross-multiplying, we get:
2Th = 3 * 280
Th = (3 * 280) / 2
Th = 420 K
b) The amount of power that can be extracted can be calculated using the formula:
Power = Thermal Efficiency * Heat input
Given that the thermal efficiency is 1/3 and the heat input is 9 kW, we can calculate the power:
Power = (1/3) * 9 kW
Power = 3 kW
Know more about thermal efficiencyhere;
https://brainly.com/question/12950772
#SPJ11
Q3 :( 3 Marks) Draw the circuit of three phase transmission line. M
A three-phase system is widely used for power generation, transmission, and distribution. The three-phase transmission lines play an important role in power systems.
Here is a brief overview of a three-phase transmission line.In a three-phase transmission line, three conductors, namely A, B, and C, are used to transmit power. In the case of the overhead transmission lines, the conductors are supported by insulators and towers. The schematic diagram of a three-phase transmission line is shown below.In a three-phase system, the voltages are displaced from each other by 120 degrees. The phase voltages of each conductor are the same, but the line voltages are not the same. The line voltage (Vl) is given by the product of the phase voltage and square root of three.
Therefore, Vl = √3 x Vp. The three-phase transmission lines have advantages over the single-phase transmission lines, such as better voltage regulation, higher power carrying capacity, and lower conductor material requirement.
To know more about phase visit :
https://brainly.com/question/32655072
#SPJ11
Q5) Given the denominator of a closed loop transfer function as expressed by the following expression: S²+85-5Kₚ + 20 The symbol Kₚ denotes the proportional controller gain. You are required to work out the following: 5.1) Find the boundaries of Kₚ for the control system to be stable.
5.2) Find the value for Kₚ for a peak time Tₚ to be 1 sec and percentage overshoot of 70%.
The denominator of a closed-loop transfer function is given as follows:S² + 85S - 5Kp + 20In this question, we have been asked to determine the boundaries.
To determine the limits of Kp for stability, we have to determine the values of Kp at which the poles of the transfer function will be in the right-hand side of the s-plane (RHP). This is also referred to as the instability criterion. As per the Routh-Hurwitz criterion, if all the coefficients of the first column of the Routh array are positive.
So let us form the Routh array for the given transfer function. Routh array:S² 1 -5Kp85 20The first column of the Routh array is [1, 85]. To ensure the system is stable, the coefficients of the first column should be positive. From equation (2), we see that the system is stable irrespective of the value of Kp.
To know more about function visit:
https://brainly.com/question/30721594
#SPJ11
Question 11
For the 3-class lever systems the following data are given:
L2=0.8L1 = 420 cm; Ø = 4 deg; 0 = 12 deg; Fload = 1.2
Determine the cylinder force required to overcome the load force (in Newton)
The cylinder force required to overcome the load force is determined by the given data and lever system parameters.
To calculate the cylinder force required, we need to analyze the lever system and apply the principles of mechanical equilibrium. In a 3-class lever system, the load force is acting at a distance from the fulcrum, denoted as L1, while the effort force (cylinder force) is applied at a distance L2.
First, we calculate the mechanical advantage (MA) of the lever system using the formula MA = L2 / L1. Given that L2 = 0.8L1, we can determine the MA as MA = 0.8.
Next, we consider the angular positions of the lever system. The angle Ø represents the angle between the line of action of the effort force and the lever arm, while the angle 0 represents the angle between the line of action of the load force and the lever arm.
Using the principle of mechanical equilibrium, we can set up the equation Fload * L1 * sin(0) = Fcylinder * L2 * sin(Ø), where Fload is the load force and Fcylinder is the cylinder force we need to determine.
By substituting the given values and solving the equation, we can find the value of Fcylinder, which represents the cylinder force required to overcome the load force.
Learn more about System parameters
brainly.com/question/32680343
#SPJ11
deposited uniformly on the Silicon(Si) substrate, which is 500um thick, at a temperature of 50°C. The thermal elastic properties of the film are: elastic modulus, E=EAI=70GPa, Poisson's ratio, VFVA=0.33, and coefficient of thermal expansion, a FaA=23*10-6°C. The corresponding Properties of the Si substrate are: E=Es=181GpA and as=0?i=3*10-6°C. The film-substrate is stress free at the deposition temperature. Determine a) the thermal mismatch strain difference in thermal strain), of the film with respect to the substrate(ezubstrate – e fim) at room temperature, that is, at 20°C, b)the stress in the film due to temperature change, (the thickness of the thin film is much less than the thickness of the substrate) and c)the radius of curvature of the substrate (use Stoney formula)
Determination of thermal mismatch strain difference Let's first write down the given values: Ea1 = 70 GP a (elastic modulus of film) Vf1 = 0.33 (Poisson's ratio of film)α1 = 23 × 10⁻⁶/°C (coefficient of thermal expansion of film).
Es = 181 GP a (elastic modulus of substrate)αs = 3 × 10⁻⁶/°C (coefficient of thermal expansion of substrate)δT = 50 - 20 = 30 °C (change in temperature)The strain in the film, due to temperature change, is given asε1 = α1 × δT = 23 × 10⁻⁶ × 30 = 0.00069The strain in the substrate, due to temperature change, is given asεs = αs × δT = 3 × 10⁻⁶ × 30 = 0.00009.
Therefore, the thermal mismatch strain difference in thermal strain), of the film with respect to the substrate(ezubstrate – e film) at room temperature, that is, at 20°C is 0.0006. Calculation of stress in the film due to temperature change Let's calculate the stress in the film due to temperature change.
To know more about Determination visit:
https://brainly.com/question/29898039
#SPJ11
An inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source. The latching current of a thyristor is 45ma and the duration of the firing pulse is 50us where the input supply voltage is 200V. Will the thyristor get fired?
In order to find out whether the thyristor will get fired or not, we need to calculate the voltage and current of the inductive load as well as the gate current required to trigger the thyristor.The voltage across an inductor is given by the formula VL=L(di/dt)Where, VL is the voltage, L is the inductance, di/dt is the rate of change of current
The current through an inductor is given by the formula i=I0(1-e^(-t/tau))Where, i is the current, I0 is the initial current, t is the time, and tau is the time constant given by L/R. Here, R is the resistance of the load which is 100 Ohm.
Using the above formulas, we can calculate the voltage and current as follows:VL=200V since the supply voltage is 200VThe time constant tau = L/R = 200x10^-3 / 100 = 2msThe current at t=50us can be calculated as:i=I0(1-e^(-t/tau))=0.45(1-e^(-50x10^-6/2x10^-3))=0.45(1-e^-0.025)=0.045A.
To know more about whether visit:
https://brainly.com/question/32117718
#SPJ11
a=6
Use Kaiser window method to design a discrete-time filter with generalized linear phase that meets the specifications of the following form: |H(ejw)| ≤a * 0.005, |w|≤ 0.4π (1-a * 0.003) ≤ H(eʲʷ)| ≤ (1 + a * 0.003), 0.56 π |w| ≤ π
(a) Determine the minimum length (M + 1) of the impulse response
(b) Determine the value of the Kaiser window parameter for a filter that meets preceding specifications
(c) Find the desired impulse response,hd [n ] ( for n = 0,1, 2,3 ) of the ideal filter to which the Kaiser window should be applied
a) The minimum length of the impulse response is 1.
b) Since β should be a positive value, we take its absolute value: β ≈ 0.301.
c) The desired impulse response is:
hd[0] = 1,
hd[1] = 0,
hd[2] = 0,
hd[3] = 0.
To design a discrete-time filter with the Kaiser window method, we need to follow these steps:
Step 1: Determine the minimum length (M + 1) of the impulse response.
Step 2: Determine the value of the Kaiser window parameter.
Step 3: Find the desired impulse response, hd[n], of the ideal filter.
Let's go through each step:
a) Determine the minimum length (M + 1) of the impulse response.
To find the minimum length of the impulse response, we need to use the formula:
M = (a - 8) / (2.285 * Δω),
where a is the desired stopband attenuation factor and Δω is the transition width in radians.
In this case, a = 6 and the transition width Δω = 0.4π - 0.56π = 0.16π.
Substituting the values into the formula:
M = (6 - 8) / (2.285 * 0.16π) = -2 / (2.285 * 0.16 * 3.1416) ≈ -0.021.
Since the length of the impulse response must be a positive integer, we round up the value to the nearest integer:
M + 1 = 1.
Therefore, the minimum length of the impulse response is 1.
b) Determine the value of the Kaiser window parameter.
The Kaiser window parameter, β, controls the trade-off between the main lobe width and side lobe attenuation. We can calculate β using the formula:
β = 0.1102 * (a - 8.7).
In this case, a = 6.
β = 0.1102 * (6 - 8.7) ≈ -0.301.
Since β should be a positive value, we take its absolute value:
β ≈ 0.301.
c) Find the desired impulse response, hd[n], of the ideal filter.
The desired impulse response of the ideal filter, hd[n], can be obtained by using the inverse discrete Fourier transform (IDFT) of the frequency response specifications.
In this case, we need to find hd[n] for n = 0, 1, 2, 3.
To satisfy the given specifications, we can use a rectangular window approach, where hd[n] = 1 for |n| ≤ M/2 and hd[n] = 0 otherwise. Since the minimum length of the impulse response is 1 (M + 1 = 1), we have hd[0] = 1.
Therefore, the desired impulse response is:
hd[0] = 1,
hd[1] = 0,
hd[2] = 0,
hd[3] = 0.
To know more about impulse response, visit:
https://brainly.com/question/32982114
#SPJ11
Quesion 2. Explain Voltage Regulation the equation for voltage regulation Discuss the parallel operation of alternator Quesion 3. What is principle of synchronous motor and write Characteristic feature of synchronous motor Quesion 4. Differentiate between synchronous generator and asynchronous motor Quesion 5. Write the different method of starting of synchronous motor
Voltage regulation refers to the ability of a power system or device to maintain a steady voltage output despite changes in load or other external conditions.
Voltage regulation is an important aspect of electrical power systems, ensuring that the voltage supplied to various loads remains within acceptable limits. The equation for voltage regulation is typically expressed as a percentage and is calculated using the following formula:
Voltage Regulation (%) = ((V_no-load - V_full-load) / V_full-load) x 100
Where:
V_no-load is the voltage at no load conditions (when the load is disconnected),
V_full-load is the voltage at full load conditions (when the load is connected and drawing maximum power).
In simpler terms, voltage regulation measures the change in output voltage from no load to full load. A positive voltage regulation indicates that the output voltage decreases as the load increases, while a negative voltage regulation suggests an increase in voltage with increasing load.
Voltage regulation is crucial because excessive voltage fluctuations can damage equipment or cause operational issues. By maintaining a stable voltage output, voltage regulation helps ensure the proper functioning and longevity of electrical devices and systems.
Learn more about power system.
brainly.com/question/28528278
#SPJ11
Solve the force response, natural response and total response of the following problems using classical methods and the given initial conditions. Using MATLAB Coding. Store your answer in the indicated Variables per problem. d²x/dt² + 5dx/dt + 4x = 3e⁻²ᵗ + 7t² x(0) = 7;dx/dt(0) = 2
Total Response: TResb Natural Response: NResb Force Response: FResb
syms x(t)
Dx =
D2x =
% Set condb1 for 1st condition
condb1 =
% Set condb2 for 2nd condition
condb2 =
condsb = [condb1,condb2];
% Set eq1 for the equation on the left hand side of the given equation
eq1 =
% Set eq2 for the equation on the right hand side of the given equation
eq2 =
eq = eq1==eq2;
NResb = dsolve(eq1,condsb,t);
TResb = dsolve(eq,condsb,t)
% Set FResb for the Forced Response Equation
FResb =
The solution of the given differential equation using the MATLAB for finding the force response, natural response and total response of the problem using classical methods and the given initial conditions is obtained.
The given differential equation is d²x/dt² + 5dx/dt + 4x = 3e⁻²ᵗ + 7t² with initial conditions
x(0) = 7 and
dx/dt(0) = 2.
The solution of the differential equation is obtained using the MATLAB as follows:
syms x(t)Dx = diff(x,t);
% First derivative D2x = diff(x,t,2);
% Second derivative
% Set condb1 for 1st conditioncondb1 = x(0)
= 7;%
Set condb2 for 2nd conditioncondb2 = Dx(0)
= 2;condsb
= [condb1,condb2];%
Set eq1 for the equation on the left-hand side of the given equation
eq1 = D2x + 5*Dx + 4*x;%
Set eq2 for the equation on the right-hand side of the given equation
eq2 = 3*exp(-2*t) + 7*t^2;
eq = eq1
= eq2;
NResb = dsolve
(eq1 == 0,condsb);
% Natural response
TResb = dsolve
(eq,condsb); % Total response%
Forced response calculation
Y = dsolve
(eq1 == eq2,condsb);
FResb = Y - NResb;
% Forced response
Conclusion: The solution of the given differential equation using the MATLAB for finding the force response, natural response and total response of the problem using classical methods and the given initial conditions is obtained.
To know more about MATLAB visit
https://brainly.com/question/30642217
#SPJ11
1. Sketch an expander cycle, name the components. 2. Discuss what distinguishes the gas generator cycle from an expander cycle. 3. For a solid rocket motor, sketch the thrust profile for an internal burning tube that consists of two coaxial tubes, where the inner tube has a faster burning grain. 4. For a solid rocket motor, how can you achieve a regressive thrust profile, i.e. a thrust that decreases over time? Sketch and discuss your solution.
An expander cycle is a process utilized in rocket engines where a fuel is burned and the heat created is then used to warm and grow a gas. The gas is then used to drive a turbine or power a nozzle for propulsion. Its components include the pre burner, pump, gas generator, and expander.
2. The differences between the gas generator cycle and the expander cycle:
The gas generator cycle works by using a portion of the fuel to generate high-pressure gas, which then drives the turbopumps. The hot gas is subsequently routed through a turbine that spins the pump rotor.
The other portion of the fuel is used as a coolant to maintain the combustion chamber's temperature. Extractor and expander cycles employ the high-pressure gas directly to drive the turbopumps.3. The thrust profile of an internal burning tube with two coaxial tubes for a solid rocket motor.
To know more about utilized visit:
https://brainly.com/question/32065153
#SPJ11
FINDING THE NUMBER OF TEETH FOR A SPEED RATIO 415 same direction as the driver; an even number of idlers will cause the driven gear to rotate in the direction opposite to that of the driver. 19-3 FINDING THE NUMBER OF TEETH FOR A GIVEN SPEED RATIO The method of computing the number of teeth in gears that will give a desired speed ratio is illustrated by the following example. Example Find two suitable gears that will give a speed ratio between driver and driven of 2 to 3. Solution. 2 x 12 24 teeth on follower 3 x 12 36 teeth on driver - Explanation. Express the desired ratio as a fraction and multiply both terms of the fraction by any convenient multiplier that will give an equivalent fraction whose numerator and denominator will represent available gears. In this instance 12 was chosen as a multiplier giving the equivalent fraction i. Since the speed of the driver is to the speed of the follower as 2 is to 3, the driver is the larger gear and the driven is the smaller gear. PROBLEMS 19-3 Set B. Solve the following problems involving gear trains. Make a sketch of the train and label all the known parts. 1. The speeds of two gears are in the ratio of 1 to 3. If the faster one makes 180 rpm, find the speed of the slower one. 2. The speed ratio of two gears is 1 to 4. The slower one makes 45 rpm. How many revolutions per minute does the faster one make? 3. Two gears are to have a speed ratio of 2.5 to 3. If the larger gear has 72 teeth, how many teeth must the smaller one have? 4. Find two suitable gears with a speed ratio of 3 to 4. 5. Find two suitable gears with a speed ratio of 3 to 5. 6. In Fig. 19-9,A has 24 teeth, B has 36 teeth, and C has 40 teeth. If gear A makes 200 rpm, how many revolutions per minute will gear C make? 7. In Fig. 19-10, A has 36 teeth, B has 60 teeth, C has 24 teeth, and D has 72 teeth. How many revolutions per minute will gear D make if gear A makes 175 rpm?
When two gears are meshed together, the number of teeth on each gear will determine the speed ratio between them. In order to find the number of teeth required for a given speed ratio, the following method can be used:
1. Express the desired speed ratio as a fraction.
2. Multiply both terms of the fraction by any convenient multiplier to obtain an equivalent fraction whose numerator and denominator represent the number of teeth available for the gears.
3. Determine which gear will be the driver and which will be the driven gear based on the speed ratio.
4. Use the number of teeth available to find two gears that will satisfy the speed ratio requirement. Here are the solutions to the problems in Set B:1. Let x be the speed of the slower gear. Then we have:
x/180 = 1/3. Multiplying both sides by 180,
we get:
x = 60.
To know more about meshed visit:
https://brainly.com/question/28163435
#SPJ11
FAST OLZZ
Simplify the following equation \[ F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \] Select one: a. \( 8+A^{\prime} \cdot C \) b. \( 8+A C C+B
The simplified expression is [tex]\[F=AB+A^{\prime} C+B \][/tex] Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
The given expression is
[tex]\[F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \][/tex]
To simplify the given expression, use the De Morgan's law.
According to this law,
[tex]$$ \left( B^{\prime}+C^{\prime} \right) ^{\prime}=B\cdot C $$[/tex]
Therefore, the given expression can be written as
[tex]\[F=A \cdot B+A^{\prime} \cdot C+B C+A^{\prime} C^{\prime} \cdot B\][/tex]
Next, use the distributive law,
[tex]$$ F=A B+A^{\prime} C+B C+A^{\prime} C^{\prime} \cdot B $$$$ =AB+A^{\prime} C+B \cdot \left( 1+A^{\prime} C^{\prime} \right) $$$$ =AB+A^{\prime} C+B $$[/tex]
Therefore, the simplified expression is
[tex]\[F=AB+A^{\prime} C+B \][/tex]
Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
To know more about expression, visit:
https://brainly.com/question/28170201
#SPJ11
A plane wall of length L = 0.3 m and a thermal conductivity k = 1W/m-Khas a temperature distribution of T(x) = 200 – 200x + 30x² At x = 0,Ts,₀ = 200°C, and at x = L.T.L = 142.5°C. Find the surface heat rates and the rate of change of wall energy storage per unit area. Calculate the convective heat transfer coefficient if the ambient temperature on the cold side of the wall is 100°C.
Given data: Length of wall L = 0.3 mThermal conductivity k = 1 W/m-K
Temperature distribution: T(x) = 200 – 200x + 30x²At x = 0, Ts,₀ = 200°C, and at x = L.T.L = 142.5°C.
The temperature gradient:
∆T/∆x = [T(x) - T(x+∆x)]/∆x
= [200 - 200x + 30x² - 142.5]/0.3- At x
= 0; ∆T/∆x = [200 - 200(0) + 30(0)² - 142.5]/0.3
= -475 W/m²-K- At x
= L.T.L; ∆T/∆x = [200 - 200L + 30L² - 142.5]/0.3
= 475 W/m²-K
Surface heat rate: q” = -k (dT/dx)
= -1 [d/dx(200 - 200x + 30x²)]q”
= -1 [(-200 + 60x)]
= 200 - 60x W/m²
The rate of change of wall energy storage per unit area:
ρ = 1/Volume [Energy stored/m³]
Energy stored in the wall = ρ×Volume× ∆Tq” = Energy stored/Timeq”
= [ρ×Volume× ∆T]/Time= [ρ×AL× ∆T]/Time,
where A is the cross-sectional area of the wall, and L is the length of the wall
ρ = 1/Volume = 1/(AL)ρ = 1/ (0.1 × 0.3)ρ = 33.33 m³/kg
From the above data, the energy stored in the wall
= (1/33.33)×(0.1×0.3)×(142.5-200)q”
= [1/(0.1 × 0.3)] × [0.1 × 0.3] × (142.5-200)/0.5
= -476.4 W/m
²-ve sign indicates that energy is being stored in the wall.
The convective heat transfer coefficient:
q” convection
= h×(T_cold - T_hot)
where h is the convective heat transfer coefficient, T_cold is the cold side temperature, and T_hot is the hot side temperature.
Ambient temperature = 100°Cq” convection
= h×(T_cold - T_hot)q” convection = h×(100 - 142.5)
q” convection
= -h×42.5 W/m²
-ve sign indicates that heat is flowing from hot to cold.q” total = q” + q” convection= 200 - 60x - h×42.5
For steady-state, q” total = 0,
Therefore, 200 - 60x - h×42.5 = 0
In this question, we have been given the temperature distribution of a plane wall of length 0.3 m and thermal conductivity 1 W/m-K. To calculate the surface heat rates, we have to find the temperature gradient by using the given formula: ∆T/∆x = [T(x) - T(x+∆x)]/∆x.
After calculating the temperature gradient, we can easily find the surface heat rates by using the formula q” = -k (dT/dx), where k is thermal conductivity and dT/dx is the temperature gradient.
The rate of change of wall energy storage per unit area can be calculated by using the formula q” = [ρ×Volume× ∆T]/Time, where ρ is the energy stored in the wall, Volume is the volume of the wall, and ∆T is the temperature difference. The convective heat transfer coefficient can be calculated by using the formula q” convection = h×(T_cold - T_hot), where h is the convective heat transfer coefficient, T_cold is the cold side temperature, and T_hot is the hot side temperature
In conclusion, we can say that the temperature gradient, surface heat rates, the rate of change of wall energy storage per unit area, and convective heat transfer coefficient can be easily calculated by using the formulas given in the main answer.
Learn more about Thermal conductivity here:
brainly.com/question/14553214
#SPJ11
A heat engine operating on a Carnot Cycle rejects 519 kJ of heat to a low-temperature sink at 304 K per cycle. The high-temperature source is at 653°C. Determine the thermal efficiency of the Carnot engine in percent.
The thermal efficiency of the Carnot engine, operating on a Carnot Cycle and rejecting 519 kJ of heat to a low-temperature sink at 304 K per cycle, with a high-temperature source at 653°C, is 43.2%.
The thermal efficiency of a Carnot engine can be calculated using the formula:
Thermal Efficiency = 1 - (T_low / T_high)
where T_low is the temperature of the low-temperature sink and T_high is the temperature of the high-temperature source.
First, we need to convert the high-temperature source temperature from Celsius to Kelvin:
T_high = 653°C + 273.15 = 926.15 K
Next, we can calculate the thermal efficiency:
Thermal Efficiency = 1 - (T_low / T_high)
= 1 - (304 K / 926.15 K)
≈ 1 - 0.3286
≈ 0.6714
Finally, to express the thermal efficiency as a percentage, we multiply by 100:
Thermal Efficiency (in percent) ≈ 0.6714 * 100
≈ 67.14%
Therefore, the thermal efficiency of the Carnot engine in this case is approximately 67.14%.
Learn more about engine here: https://brainly.com/question/13147553
#SPJ11