The period of a low orbit satellite around a planet with free fall acceleration half that of Jupiter but three times the radius of the Jupiter's is 4736.17 s.
a. The period of a low orbit satellite orbiting near the surface of Jupiter is about 10500 s. If the free fall acceleration on the surface is 25 m/s², what is the radius of Jupiter (the orbital radius)?Given,Period of the low orbit satellite, T = 10500 sAcceleration due to gravity on Jupiter, g = 25 m/s²Let the radius of Jupiter be r.Then, the height of the satellite above Jupiter's surface = r.T = 2π√(r/g)10500 = 2π√(r/25)10500/2π = √(r/25)r/25 = (10500/2π)²r = 753850.32 mTherefore, the radius of Jupiter is 753850.32 m.
b. The acceleration due to gravity on this planet is half of that of Jupiter. So, g = 12.5 m/s²The radius of the planet is three times the radius of Jupiter. Let R be the radius of this planet. Then, R = 3r.Height of the satellite from the surface of the planet = R - r.T' = 2π√((R - r)/g)T' = 2π√(((3r) - r)/(12.5))T' = 2π√(2r/12.5)T' = 2π√(8r/50)T' = 2π√(4r/25)T' = (2π/5)√rT' = (2π/5)√(753850.32)T' = 4736.17 sTherefore, the period of a low orbit satellite around a planet with free fall acceleration half that of Jupiter but three times the radius of the Jupiter's is 4736.17 s.
Learn more about period:
https://brainly.com/question/1073522
#SPJ11
Chec A crate of mass m-12.4 kg is pulled by a massless rope up a 36.9° ramp. The rope passes over an ideal pulley and is attached to a hanging crate of mass m2-16.3 kg. The crates move 1.50 m, starting from rest. If the frictional force on the sliding crate has magnitude 22.8 N and the tension in the rope is 121.5 N, find the total work done on the sliding crate. m₁ The total work done on the sliding crate is
A crate of mass m-12.4 kg is pulled by a massless rope up a 36.9° ramp. The rope passes over an ideal pulley and is attached to a hanging crate of mass m2-16.3 kg. Total Work = Work₁ + Work₂
To find the total work done on the sliding crate, we need to consider the work done by different forces acting on it.
The work done by the tension in the rope (T) can be calculated using the formula:
Work₁ = T * displacement₁ * cos(θ₁)
where displacement₁ is the distance the sliding crate moves along the ramp and θ₁ is the angle between the displacement and the direction of the tension force.
In this case, the displacement₁ is given as 1.50 m and the tension force T is given as 121.5 N. The angle θ₁ is the angle of the ramp, which is 36.9°. Therefore, we can calculate the work done by the tension force as:
Work₁ = 121.5 * 1.50 * cos(36.9°)
Next, we need to consider the work done by the frictional force (f) acting on the sliding crate. The work done by the frictional force is given by:
Work₂ = f * displacement₂
where displacement₂ is the distance the crate moves horizontally. In this case, the frictional force f is given as 22.8 N. The displacement₂ is equal to the displacement₁ because the crate moves horizontally over the same distance.
Therefore, we can calculate the work done by the frictional force as:
Work₂ = 22.8 * 1.50
Finally, the total work done on the sliding crate is the sum of the work done by the tension force and the work done by the frictional force:
Total Work = Work₁ + Work₂
To know more about massless refer here:
https://brainly.com/question/30467003#
#SPJ11
Rutherford atomic model. In 1911, Ernest Rutherford sent a particles through atoms to determine the makeup of the atoms. He suggested: "In order to form some idea of the forces required to deflect an a particle through a large angle, consider an atom [as] containing a point positive charge Ze at its centre and surrounded by a distribution of negative electricity -Ze uniformly distributed within a sphere of
radius R." For his model, what is the electric field E at a distance + from the centre for a point inside the atom?
Ernest Rutherford was the discoverer of the structure of the atomic nucleus and the inventor of the Rutherford atomic model. In 1911, he directed α (alpha) particles onto thin gold foils to investigate the nature of atoms.
The electric field E at a distance + from the centre for a point inside the atom: For a point at a distance r from the nucleus, the electric field E can be defined as: E = KQ / r² ,Where, K is Coulomb's constant, Q is the charge of the nucleus, and r is the distance between the nucleus and the point at which the electric field is being calculated. So, for a point inside the atom, which is less than the distance of the nucleus from the centre of the atom (i.e., R), we can calculate the electric field as follows: E = K Ze / r².
Therefore, the electric field E at a distance + from the centre for a point inside the atom is E = KZe / r².
Let's learn more about Rutherford atomic model:
https://brainly.com/question/30087408
#SPJ11
The cliff divers of Acapulco push off horizontally from rock platforms about hhh = 39 mm above the water, but they must clear rocky outcrops at water level that extend out into the water LLL = 4.1 mm from the base of the cliff directly under their launch point
1.a What minimum pushoff speed is necessary to clear the rocks?
1.b How long are they in the air?
The cliff divers of Acapulco push off horizontally from rock platforms about hhh = 39 mm above the water, but they must clear rocky outcrops at water level that extend out into the water LLL = 4.1 mm from the base of the cliff directly under their launch point. The required minimum pushoff speed is 2.77 m/s and they are in the air for 0.0891 s.
Given data: The height of the rock platforms (hhh) = 39 mm
The distance of rocky outcrops at water level that extends out into the water (LLL) = 4.1 mm. We need to find the minimum push-off speed required to clear the rocks
(a) and how long they are in the air (t).a) Minimum push-off speed (v) required to clear the rocks is given by the formula:
v² = 2gh + 2gh₀Where,g is the acceleration due to gravity = 9.81 m/s²
h is the height of the rock platform = 39 mm = 39/1000 m (as the question is in mm)
h₀ is the height of the rocky outcrop = LLL = 4.1 mm = 4.1/1000 m (as the question is in mm)
On substituting the values, we get:
v² = 2 × 9.81 × (39/1000 + 4.1/1000)
⇒ v² = 0.78 × 9.81⇒ v = √7.657 = 2.77 m/s
Therefore, the minimum push-off speed required to clear the rocks is 2.77 m/s.
b) Time of flight (t) is given by the formula:
h = (1/2)gt²
On substituting the values, we get:
39/1000 = (1/2) × 9.81 × t²
⇒ t² = (39/1000) / (1/2) × 9.81
⇒ t = √0.007958 = 0.0891 s
Therefore, they are in the air for 0.0891 s. Hence, the required minimum push-off speed is 2.77 m/s and they are in the air for 0.0891 s.
For further information on Speed visit :
https://brainly.com/question/17661499
#SPJ11
Q 12A: A rocket has an initial velocity V; and mass M= 2000 KG. The thrusters are fired, and the rocket undergoes constant acceleration for 18.1s resulting in a final velocity of Vf Part (a) What is the magnitude, in meters per squared second, of the acceleration? Part (b) Calculate the Kinetic energy before and after the thrusters are fired. ū; =(-25.7 m/s) î+(13.8 m/s) į Ūg =(31.8 m/s) î+(30.4 m/s) Î.
Let the acceleration of the rocket be denoted as a. During the constant acceleration phase, the final velocity (Vf) can be calculated using the equation Vf = V + a * t, where V is the initial velocity and t is the time interval.
Given that the initial velocity V is 0 (the rocket starts from rest) and the final velocity Vf is known, we have:
Vf = a * t
0.183 m/s² = a * 18.1 s
Therefore, the magnitude of the acceleration is 0.183 meters per squared second.
Part (b):
The kinetic energy (K.E) of an object is given by the formula K.E = (1/2) * m * v², where m is the mass of the object and v is its velocity.
Before the thrusters are fired, the rocket has an initial velocity of zero. Using the given values of mass (M = 2000 kg) and the velocity vector (ū; = (-25.7 m/s) î + (13.8 m/s) į), we can calculate the initial kinetic energy.
K.E before thrusters are fired = (1/2) * M * (ū;)^2
K.E before thrusters are fired = (1/2) * 2000 kg * ((-25.7 m/s)^2 + (13.8 m/s)^2)
K.E before thrusters are fired = 2.04 × 10⁶ J
After the thrusters are fired, the final velocity vector is given as Ūg = (31.8 m/s) î + (30.4 m/s) Î. Using the same formula, we can calculate the final kinetic energy.
K.E after thrusters are fired = (1/2) * M * (Ūg)^2
K.E after thrusters are fired = (1/2) * 2000 kg * ((31.8 m/s)^2 + (30.4 m/s)^2)
K.E after thrusters are fired = 9.58 × 10⁵ J
Therefore, the kinetic energy before the thrusters are fired is 2.04 × 10⁶ J, and the kinetic energy after the thrusters are fired is 9.58 × 10⁵ J.
To Learn more about velocity. Click this!
brainly.com/question/33264778
#SPJ11
Twins A and B are both 19.0 years old when twin B decides to embark on a space voyage. Twin B blasts off from Earth and travels at a speed of 0.97c. Twin A remains on Earth, and after waiting 35.0 years, twin A is reunited with twin B, who has returned from the space voyage. Twin A is now 54.0 years old. How old is twin B?
ΔT = ΔT0 / (1 - v^2/c^2)^1/2
ΔT is the time elapsed in the moving frame and ΔT0 is the proper time that has elapsed in the frame where the clock is stationary
ΔT = 35 years which is the elapsed time in frame A - age of twin in that frame
ΔT0 = 35 * (1 - .97^2) = 2.07 yrs time elapsed for twin (B) in stationary frame B - measured WRT a clock at a single point
the proper time in frame B will be the actual elapsed time (age) that has passed in that frame - frame A is moving WRT frame (B)
No, Dir The speed of a cosmic ray muon is 29.8 cm/ns. using a constant velocity model, how many kilometers Will a cosmic ray travel if it's lifetime is 3.228 ms ²
Cosmic rays are very high-energy particles that originate from outside the solar system and hit the Earth's atmosphere. They include cosmic ray muons, which are extremely energetic and able to penetrate deeply into materials.
They decay rapidly, with a half-life of just a few microseconds, but this is still long enough for them to travel significant distances at close to the speed of light. If the speed of a cosmic ray muon is 29.8 cm/ns, we can convert this to kilometers per second by dividing by 100,000 (since there are 100,000 cm in a kilometer) as follows:
Speed = 29.8 cm/ns = 0.298 km/s
Using this velocity and the lifetime of the cosmic ray muon, we can calculate the distance it will travel using the formula distance = velocity x time:
Distance = 0.298 km/s x 3.228 ms = 0.000964 km = 0.964 m
t will travel a distance of approximately 0.964 meters or 96.4 centimeters if its lifetime is 3.228 ms.
Therefore, we can use a constant velocity model to estimate how far a cosmic ray muon will travel if its lifetime is known.
To know more about energetic visit:
https://brainly.com/question/31965710
#SPJ11
The isotope, Cobalt 57, decays by electron capture to Iron 57 with a half life of 272 days. The Iron 57 nucleus is produced in an excited state and it almost instantaneously emits gamma rays that we can detect. Find the mean lifetime and decay constant for Cobalt 57. . 1st, convert half life from days to seconds. T1/2 = 272 days (in seconds) Tmean = T1/2/In2 (in days) X = 1/Tmean (decay constant) . . O 682 days, 2.05 x 10-6-1 O 392 days, 2.95 x 108 1 O 216 days, 4.12 x 10-851 O No answer text provided. Which scan has the most dangerous levels of radiation exposure? O No answer text provided. OCT MRI OPET
The question asks for the mean lifetime and decay constant of Cobalt 57, which decays by electron capture to Iron 57 with a half-life of 272 days. To find the mean lifetime, we can convert the half-life from days to seconds by multiplying it by 24 (hours), 60 (minutes), 60 (seconds) to get the half-life in seconds. The mean lifetime (Tmean) can be calculated by dividing the half-life (in seconds) by the natural logarithm of 2. The decay constant (X) is the reciprocal of the mean lifetime (1/Tmean).
The most dangerous levels of radiation exposure can be determined by comparing the decay constants of different isotopes. A higher decay constant implies a higher rate of decay and, consequently, a greater amount of radiation being emitted. Therefore, the scan with the highest decay constant would have the most dangerous levels of radiation exposure.
Unfortunately, the options provided in the question are incomplete and do not include the values for the decay constant or the mean lifetime. Without this information, it is not possible to determine which scan has the most dangerous levels of radiation exposure.
Learn more about electron :
https://brainly.com/question/12001116
#SPJ11
1.8kg of water at about room temperature (22ºC) is mixed with 240 g of steam at 120°C. Determine the final temperature of the water. The specific heat capacity of water is 4186 J/kg/°C
By heat transfer the final temperature of water is 27.85⁰C.
The heat transfer to raise the temperature by ΔT of mass m is given by the formula:
Q = m× C × ΔT
Where C is the specific heat of the material.
Given information:
Mass of water, m₁ = 1.8kg
The temperature of the water, T₁ =22°C
Mass of steam, m₂ = 240g or 0.24kg
The temperature of the steam, T₂ = 120⁰C
Specific heat of water, C₁ = 4186 J/kg/°C
Let the final temperature of the mixture be T.
Heat given by steam + Heat absorbed by water = 0
m₂C₂(T-T₂) + m₁C₁(T-T₁) =0
0.24×1996×(T-120) + 1.8×4186×(T-22) = 0
479.04T -57484.8 + 7534.8T - 165765.6 =0
8013.84T =223250.4
T= 27.85⁰C
Therefore, by heat transfer the final temperature of water is 27.85⁰C.
To know more about heat transfer, click here:
https://brainly.com/question/31065010
#SPJ4
A 994 turns rectangular loop of wire has an area per turn of 2.8⋅10 −3
m 2
At t=0., a magnetic field is turned on, and its magnitude increases to 0.50T after Δt=0.75s have passed. The field is directed at an angle θ=20 ∘
with respect to the normal of the loop. (a) Find the magnitude of the average emf induced in the loop. ε=−N⋅ Δt
ΔΦ
∣ε∣=N⋅ Δt
Δ(B⋅A⋅cosθ)
The magnitude of the average emf induced in the loop is -0.567887 V.
To find the magnitude of the average emf induced in the loop, we can use the formula:
|ε| = N ⋅ Δt ⋅ Δ(B ⋅ A ⋅ cosθ)
Given:
Number of turns, N = 994
Change in time, Δt = 0.75 s
Area per turn, A = 2.8 × 10^(-3) m^2
Magnetic field, B = 0.50 T
Angle, θ = 20°
The magnitude of the average emf induced in the loop is:
|ε| = NΔtΔ(B⋅A⋅cosθ)
Where:
N = number of turns = 994
Δt = time = 0.75 s
B = magnetic field = 0.50 T
A = area per turn = 2.8⋅10 −3 m 2
θ = angle between the field and the normal of the loop = 20 ∘
Plugging in these values, we get:
|ε| = (994)(0.75)(0.50)(2.8⋅10 −3)(cos(20 ∘))
|ε| = -0.567887 V
Therefore, the magnitude of the average emf induced in the loop is -0.567887 V. The negative sign indicates that the induced emf opposes the change in magnetic flux.
To learn more about emf click here; brainly.com/question/14263861
#SPJ11
M Sodium is a monovalent metal having a density of 0.971 g / cm³ and a molar mass of 29.0 g/mol. Use this information to calculate (a) the density of charge carricrs.
The density of charge carriers is 0.0335 g/cm³ per mol.
The density of charge carriers can be calculated using the formula:
Density of charge carriers = (density of the metal) / (molar mass of the metal)
In this case, the density of sodium is given as 0.971 g/cm³ and the molar mass of sodium is 29.0 g/mol.
Substituting these values into the formula, we get:
Density of charge carriers = 0.971 g/cm³ / 29.0 g/mol
To calculate this, we divide 0.971 by 29.0, which gives us 0.0335 g/cm³ per mol.
Therefore, the density of charge carriers is 0.0335 g/cm³ per mol.
Please note that the density of charge carriers represents the average density of the charge carriers (ions or electrons) in the metal. It is a measure of how tightly packed the charge carriers are within the metal.
To know more about density visit:
https://brainly.com/question/29775886
#SPJ11
A fully charged capacitor connected to a battery and with the gap filled with dielectric has energy U 0 . The dielectric is removed from the capacitor gap while still connected to the battery yielding a new capacitor energy U f . Select the correct statement. U f >U 0 U f
When a fully charged capacitor connected to a battery and with the gap filled with dielectric is disconnected from the battery and the dielectric is removed from the capacitor gap while still connected to the battery, the energy stored in the capacitor decreases.
The correct statement is that Uf < U0.
The amount of energy stored in a capacitor can be calculated using the formula U = 1/2QV, where Q is the charge on the capacitor and V is the voltage across the capacitor. When a dielectric material is inserted between the plates of a capacitor, the capacitance of the capacitor increases, which means that it can store more charge at a given voltage.
This results in an increase in the energy stored in the capacitor.
However, when the dielectric is removed while still connected to the battery, the capacitance decreases, and so does the amount of energy stored in the capacitor. Thus, Uf < U0.
learn more about capacitor here
https://brainly.com/question/27393410
#SPJ11
The electric field strength in a region is 1900 N/C. What is the force on an object with a charge of 0.0035 C?___N
The force experienced by an object with a charge in an electric field can be calculated using the equation F = q * E, where F is the force, q is the charge of the object, and E is the electric field strength.
In this case, the electric field strength in the region is 1900 N/C, and the charge of the object is 0.0035 C. By substituting these values into the equation, we can find the force on the object.
The force on the object is given by:
F = 0.0035 C * 1900 N/C
Multiplying the charge of the object (0.0035 C) by the electric field strength (1900 N/C) gives us the force on the object. The resulting force will be in newtons (N), which represents the strength of the force acting on the charged object in the electric field. Therefore, the force on the object is equal to 6.65 N.
Learn more about the charge here:
brainly.com/question/13871705
#SPJ11
(hrwc10p24_6e) A bullet of mass 6.0 g is fired horizontally into a 2.7 kg wooden block at rest on a horizontal surface. The coefficient of kinetic friction between block and surface is 0.32. The bullet comes to rest in the block, which moves 2.40 m. (a) What is the speed of the block immediately after the bullet comes to rest within it? Submit Answer Tries 0/8 (b) At what speed is the bullet fired? Submit Answer Tries 0/7
22)In this problem, a bullet is fired horizontally into a wooden block at rest on a horizontal surface. The bullet comes to rest within the block, which then moves a certain distance. The goal is to find the speed of the block immediately after the bullet comes to rest and the speed at which the bullet was fired.
To solve this problem, we can apply the principle of conservation of momentum. Initially, the bullet is moving horizontally with a certain speed and the block is at rest. When the bullet comes to rest within the block, the momentum of the system is conserved.
The momentum before the collision is equal to the momentum after the collision. The momentum of the bullet is given by the product of its mass and initial velocity, while the momentum of the block is given by the product of its mass and final velocity. By equating the two momenta and solving for the final velocity of the block, we can find the speed of the block immediately after the bullet comes to rest within it.
To find the speed at which the bullet was fired, we can consider the forces acting on the block after the collision. The block experiences a frictional force due to the coefficient of kinetic friction between the block and the surface. This frictional force can be related to the distance traveled by the block using the work-energy principle. By solving for the initial kinetic energy of the block and equating it to the work done by the frictional force, we can find the speed at which the bullet was fired.
Learn more about Horizontal surface:
https://brainly.com/question/28541505
#SPJ11
Terrence goes for a walk. He walks 2.0 km north, then turns and walks 4.0 km south of east. What is his displacement vector?
Terrence's displacement vector is 4.0 km east and 2.0 km north.
How can we arrive at this result?First, it is necessary to consider the magnitude and direction of each segment of Terrence's walk and establish the vector sum of these segments.
Terrence walked 2.0 km north and then 4.0 km east. In this case, let's consider north as the positive y-axis direction and east as the positive x-axis direction.
Therefore, we can conclude that:
We have a component of displacement of 2.0 km in the y direction.We have a component of displacement of 4.0 km in the x direction.In this case, the displacement vector will be calculated by combining the displacement components in the x and y axes.
Therefore, Terrence's displacement vector is 4.0 km east and 2.0 km north.
Learn more about vectors:
https://brainly.com/question/29740341
#SPJ4
Question 5: A europium-156 nucleus has a mass of 155.924752 amu. (a) Calculate the mass defect (Am) in amu and kg for the breaking of one nucleus (1 mol = 6.022 x 1023 nuclei) of europium-156 into its component nucleons if the mass of a proton = 1.00728 amu and the mass of a neutron = 1.00867 amu. (b) Calculate the binding energy (in J) of the nucleus given the speed of light = 3.0 x 10 m/s.
The mass defect of one nucleus of europium-156 is 0.100688 amu. The mass defect of one nucleus of europium-156 is 1.67 x 10-27 kg.
(a) A europium-156 nucleus has a mass of 155.924752 amu. To calculate the mass defect (Am) in amu and kg for the breaking of one nucleus (1 mol = 6.022 x 1023 nuclei) of europium-156 into its component nucleons if the mass of a proton = 1.00728 amu and the mass of a neutron = 1.00867 amu, we can use the formula:
Am = (Zmp + Nmn) - M
where Am is the mass defect, Z is the atomic number, mp is the mass of a proton, N is the number of neutrons, mn is the mass of a neutron, and M is the mass of the nucleus.
Given that europium-156 has 63 protons and 93 neutrons, we can substitute the values into the formula to get:
Am = (63 x 1.00728 + 93 x 1.00867) - 155.924752
Am = 0.100688 amu
To convert this into kilograms, we use the conversion factor 1 amu = 1.66 x 10-27 kg:
Am = 0.100688 amu x 1.66 x 10-27 kg/amu
Am = 1.67 x 10-27 kg
(b) To calculate the binding energy (in J) of the nucleus given the speed of light = 3.0 x 108 m/s, we can use Einstein's equation:
E = mc2
where E is the binding energy, m is the mass defect, and c is the speed of light
Given that the mass defect is 0.100688 amu, we can convert this into kilograms using the conversion factor 1 amu = 1.66 x 10-27 kg:
m = 0.100688 amu x 1.66 x 10-27 kg/amu
m = 1.67 x 10-28 kg
Substituting the values into the equation, we get:
E = 1.67 x 10-28 kg x (3.0 x 108 m/s)2
E = 1.505 x 10-11 J
Therefore, the mass defect of one nucleus of europium-156 is 0.100688 amu and the mass defect of one nucleus of europium-156 is 1.67 x 10-27 kg. The binding energy of the nucleus is 1.505 x 10-11 J.
To know more about mass defect visit:
brainly.com/question/29099255
#SPJ11
Describe that the gravitational potential energy is
measured from a reference
level and can be positive or negative, to denote the orientation
from the
reference level.
Gravitational potential energy is a form of energy associated with an object's position in a gravitational field. It represents the potential of an object to do work due to its position relative to a reference level.
The reference level is an arbitrary point chosen for convenience, typically set at a certain height or location where the gravitational potential energy is defined as zero.
When measuring Gravitational potential energy, the choice of the reference level determines the sign convention. Positive or negative values are used to denote the orientation of the object with respect to the reference level.
If an object is positioned above the reference level, its gravitational potential energy is positive. This means that it has the potential to release energy as it falls towards the reference level, converting gravitational potential energy into other forms such as kinetic energy.
Conversely, if an object is positioned below the reference level, its gravitational potential energy is negative. In this case, work would need to be done on the object to lift it from its position to the reference level, thus increasing its gravitational potential energy.
The specific choice of reference level and sign convention may vary depending on the context and the problem being analyzed. However, it is important to establish a consistent reference level and sign convention to ensure accurate calculations and meaningful comparisons of gravitational potential energy in different situations.
Learn more about kinetic energy from the given link
https://brainly.com/question/8101588
#SPJ11
Gravitational potential energy, represented by the formula PE = m*g*h, depends on an object's mass, gravity, and height from a reference level. Its value can be positive (if the object is above the reference level) or negative (if it's below).
Explanation:Gravitational potential energy is the energy of an object or body due to the height difference from a reference level. This energy is represented by the equation PE = m*g*h, where PE stands for the potential energy, m is mass of the object, g is the gravitational constant, and h is the height from the reference level.
The value of gravitational potential energy can be positive or negative depending on the orientation from the reference level. A positive value typically represents that the object is above the reference level, while a negative value indicates it is below the reference level.
Learn more about Gravitational potential energy here:https://brainly.com/question/23134321
#SPJ2
Suppose that you built the circuit given in Figure 3-2 of your lab instructions with slide wire of total length 7.7cm and try to experimentally determine the value of the unknown resistance Rx where Rc is 7.3. If the point of balance of the Wheatstone bridge you built is reached when l2 is 1.8 cm , calculate the experimental value for Rx. Give your answer in units of Ohms with 1 decimal.
In the circuit given in Figure 3-2 of your lab instructions with slide wire of total length 7.7cm, we need to experimentally determine the value of the unknown resistance Rx where Rc is 7.3.
If the point of balance of the Wheatstone bridge we built is reached when l2 is 1.8 cm, we have to calculate the experimental value for Rx.
The Wheatstone bridge circuit shown in Figure 3-2 is balanced when the potential difference across point B and D is zero.
This happens when R1/R2 = Rx/R3. Thus, the resistance Rx can be determined as:
Rx = (R1/R2) * R3, where R1, R2, and R3 are the resistances of the resistor in the circuit.
To find R2, we use the slide wire of total length 7.7 cm. We can say that the resistance of the slide wire is proportional to its length.
Thus, the resistance of wire of length l1 would be (R1 / 7.7) l1, and the resistance of wire of length l2 would be (R2 / 7.7) l2.
Using these formulas, the value of R2 can be calculated:
R1 / R2 = (l1 - l2) / l2 => R2
= R1 * l2 / (l1 - l2)
= 3.3 * 1.8 / (7.7 - 1.8)
= 0.905 Ω.
Now that we know the value of R2, we can calculate the value of Rx:Rx = (R1 / R2) * R3 = (3.3 / 0.905) * 7.3 = 26.68 Ω
Therefore, the experimental value for Rx is 26.7 Ω.
To know more about resistance visit:
https://brainly.com/question/32301085
#SPJ11
here, there is a concave mirror with an upright object infront of it. the mirror has r= 21cm. the mirror provides an inverted image at d=35.1cm. how far is the object from the mirror, answer in cm in the hundredth place.
The object is located 19.95 cm away from the concave mirror.
To determine the distance of the object from the mirror, we can use the mirror equation:
1/f = 1/v - 1/u
where f is the focal length of the mirror, v is the distance of the image from the mirror, and u is the distance of the object from the mirror.
In this case, the focal length (f) is half the radius of curvature (r) of the mirror. Given that r = 21 cm, the focal length is 10.5 cm.
Substituting the given values into the mirror equation, we have:
1/10.5 = 1/35.1 - 1/u
Simplifying the equation, we find:
1/u = 1/10.5 - 1/35.1
= (35.1 - 10.5)/(10.5 * 35.1)
= 24.6/368.55
≈ 0.06678
Taking the reciprocal of both sides, we find:
u ≈ 1/0.06678
≈ 14.97 cm
Therefore, the object is approximately 19.95 cm (rounded to the hundredth place) away from the concave-mirror.
To learn more about concave-mirror , click here : https://brainly.com/question/31379461
#SPJ11
In general, how does changing the pressure acting on a
material effect the temperature required for a phase change (i.e.
the boiling temperature of water)
Changing the pressure acting on a material affects the temperature required for a phase change (i.e., the boiling temperature of water) in a general way. The following is an explanation of the connection between pressure and phase change:
Pressure is defined as the force that a gas or liquid exerts per unit area of the surface that it is in contact with. The boiling point of a substance is defined as the temperature at which the substance changes phase from a liquid to a gas or a vapor. There is a connection between pressure and the boiling temperature of water. When the pressure on a liquid increases, the boiling temperature of the liquid also increases. This is due to the fact that boiling occurs when the vapor pressure of the liquid equals the pressure of the atmosphere.
When the pressure is increased, the vapor pressure must also increase to reach the pressure of the atmosphere. As a result, more energy is required to cause the phase change, and the boiling temperature rises as a result.
As a result, the boiling temperature of water rises as the pressure on it increases. When the pressure is decreased, the boiling temperature of the liquid decreases as well.
Let's learn more about phase change:
https://brainly.com/question/1821363
#SPJ11
Four identical charges (+2μC each ) are brought from infinity and fixed to a straight line. The charges are located 0.40 m apart. Determine the electric potential energy of this group.
The electric potential energy of the four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m is 1.44 × 10^-5 J.
To calculate the electric potential energy of a group of charges, the formula is given as U = k * q1 * q2 / r where, U is the electric potential energy of the group k is Coulomb's constant q1 and q2 are the charges r is the distance between the charges.
Given that there are four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m. We have to calculate the electric potential energy of this group of charges.
The electric potential energy formula becomes:
U = k * q1 * q2 / r = (9 × 10^9 Nm^2/C^2) × (2 × 10^-6 C)^2 × 4 / 0.40 m
U = 1.44 × 10^-5 J.
Therefore, the electric potential energy of the four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m is 1.44 × 10^-5 J.
Learn more about electric potential energy:
https://brainly.com/question/33229290
#SPJ11
Suppose we have a piece of a candy bar that has an initial mass of 28g. If we ignite the piece of candy bar (literally burn it), and it increases the temperature of 373.51g of water from
15.33°C to 74.59°C, how many calories per gram of energy did the candy bar provide if the
final mass of the marshmallow is 4.22? Note: 1.00 cal = 4.184 J. Give your answer in units of cal/g. Note: In the space below, please enter you numerical answer. Do not enter any units. If you enter units, your answer will be marked as incorrect. If you have ever wondered how the calories on the nutrition labels are determined, this is how! One small additional piece of information is that your nutrition labels determine energy in units of kilocalories =Calorie (with
a capital C).
The candy bar provides approximately 29537.15 calories per gram of energy.
To calculate the energy provided by the candy bar per gram in calories (cal/g),
We can use the equation:
Energy = (mass of water) * (specific heat capacity of water) * (change in temperature)
Given:
Initial mass of the candy bar = 28 g
Mass of water = 373.51 g
Initial temperature of the water = 15.33°C
Final temperature of the water = 74.59°C
Final mass of the candy bar = 4.22 g
We need to convert the temperature from Celsius to Kelvin because the specific heat capacity of water is typically given in units of J/(g·K).
Change in temperature = (Final temperature - Initial temperature) in Kelvin
Change in temperature = (74.59°C - 15.33°C) + 273.15 ≈ 332.41 K
The specific heat capacity of water is approximately 4.184 J/(g·K).
Now we can substitute the values into the equation:
Energy = (373.51 g) * (4.184 J/(g·K)) * (332.41 K)
Energy ≈ 520994.51 J
To convert the energy from joules (J) to calories (cal), we divide by the conversion factor:
Energy in calories = 520994.51 J / 4.184 J/cal
Energy in calories ≈ 124633.97 cal
Finally, to find the energy provided by the candy bar per gram in calories (cal/g), we divide the energy in calories by the final mass of the candy bar:
Energy per gram = 124633.97 cal / 4.22 g
Energy per gram ≈ 29537.15 cal/g
Therefore, the candy bar provided approximately 29537.15 calories per gram of energy.
Learn more about Calorie from the given link :
https://brainly.com/question/830145
#SPJ11
If you could please include the formulas needed and explain how to get the answer I would appreciate it so I can learn this type of problem.
A string has both ends fixed. The string is vibrated at a variable frequency. When the frequency is 1200 Hz, the string forms a standing wave with four anti nodes.
(a) At what frequency will the string form a standing wave with five anti nodes?
(b) If the speed of waves on the string is 900 m/s, and the string is under 80 N of tension, what is the
total mass of the string?
The frequency of the wave when there are five anti nodes is 14400 Hz. The total mass of the string is 2.12 x 10⁻⁴ kg.
a) The standing wave that the string forms has anti nodes. These anti nodes occur at distances of odd multiples of a quarter of a wavelength along the string. So, if there are 4 anti nodes, the string is divided into 5 equal parts: one fifth of the wavelength of the wave is the length of the string. Let λ be the wavelength of the wave corresponding to the 4 anti-nodes. Then, the length of the string is λ / 5.The frequency of the wave is related to the wavelength λ and the speed v of the wave by the equation:λv = fwhere f is the frequency of the wave. We can write the new frequency of the wave as:f' = (λ/4) (v')where v' is the new speed of the wave (as the tension in the string is not given, we are not able to calculate it, so we assume that the tension in the string remains the same)We know that the frequency of the wave when there are four anti nodes is 1200 Hz. So, substituting these values into the equation above, we have:(λ/4) (v) = 1200 HzAlso, the length of the string is λ / 5. Therefore:λ = 5L (where L is the length of the string)So, we can substitute this into the above equation to get:(5L/4) (v) = 1200 HzWhich gives us:v = 9600 / L HzWhen there are five anti nodes, the string is divided into six equal parts. So, the length of the string is λ / 6. Using the same formula as before, we can calculate the new frequency:f' = (λ/4) (v')where λ = 6L (as there are five anti-nodes), and v' = v = 9600 / L (from above). Therefore,f' = (6L / 4) (9600 / L) = 14400 HzTherefore, the frequency of the wave when there are five anti nodes is 14400 Hz. Thus, the answer to part (a) is:f' = 14400 Hz
b) The speed v of waves on a string is given by the equation:v = √(T / μ)where T is the tension in the string and μ is the mass per unit length of the string. Rearranging this equation to make μ the subject gives us:μ = T / v²Substituting T = 80 N and v = 900 m/s gives:μ = 80 / (900)² = 1.06 x 10⁻⁴ kg/mTherefore, the mass per unit length of the string is 1.06 x 10⁻⁴ kg/m. We need to find the total mass of the string. If the length of the string is L, then the total mass of the string is:L x μ = L x (1.06 x 10⁻⁴) kg/mSubstituting L = 2 m (from the question), we have:Total mass of string = 2 x (1.06 x 10⁻⁴) = 2.12 x 10⁻⁴ kgTherefore, the total mass of the string is 2.12 x 10⁻⁴ kg.
Learn more about frequency:
https://brainly.com/question/29739263
#SPJ11
A piece of metal weighing 0.292 kg was heated to 100.0 °C and then put it into 0.127 kg of water (initially at 23.7 °C). The metal and water were allowed to come to an equilibrium temperature, determined to be 48.3°C. Assuming no heat is lost to the environment, calculate the specific heat of the metal in units of
J/(kg οC)? The specific heat of water is 4186 J/(kg οC).
The specific heat of the metal is approximately -960 J/(kg οC).
To calculate the specific heat of the metal, we can use the principle of energy conservation. The heat gained by the water is equal to the heat lost by the metal. The equation for heat transfer is given by:
Q = m1 * c1 * ΔT1 = m2 * c2 * ΔT2
where:
Q is the heat transferred (in Joules),
m1 and m2 are the masses of the metal and water (in kg),
c1 and c2 are the specific heats of the metal and water (in J/(kg οC)),
ΔT1 and ΔT2 are the temperature changes of the metal and water (in οC).
Let's plug in the given values:
m1 = 0.292 kg (mass of the metal)
c1 = ? (specific heat of the metal)
ΔT1 = 48.3 °C - 100.0 °C = -51.7 °C (temperature change of the metal)
m2 = 0.127 kg (mass of the water)
c2 = 4186 J/(kg οC) (specific heat of the water)
ΔT2 = 48.3 °C - 23.7 °C = 24.6 °C (temperature change of the water)
Using the principle of energy conservation, we have:
m1 * c1 * ΔT1 = m2 * c2 * ΔT2
0.292 kg * c1 * (-51.7 °C) = 0.127 kg * 4186 J/(kg οC) * 24.6 °C
Simplifying the equation:
c1 = (0.127 kg * 4186 J/(kg οC) * 24.6 °C) / (0.292 kg * (-51.7 °C))
c1 ≈ -960 J/(kg οC)
The specific heat of the metal is approximately -960 J/(kg οC). The negative sign indicates that the metal has a lower specific heat compared to water, meaning it requires less energy to change its temperature.
Learn more about heat from the given link
https://brainly.com/question/934320
#SPJ11
A magnifying glass gives an angular magnification of 4 for a person with a near-point distance of sN = 22 cm. What is the focal length of the lens?
The focal length of the magnifying glass lens is approximately -5.5 cm.
The angular magnification (m) of the magnifying glass is given as 4, and the near-point distance (sN) of the person is 22 cm. To find the focal length (f) of the lens, we can use the formula:
f = -sN / m
Substituting the given values:
f = -22 cm / 4
f = -5.5 cm
The negative sign indicates that the lens is a diverging lens, which is typical for magnifying glasses. Therefore, the focal length of the magnifying glass lens is approximately -5.5 cm. This means that the lens diverges the incoming light rays and creates a virtual image that appears larger and closer to the observer.
learn more about lens click here;
brainly.com/question/29834071
#SPJ11
Problem 1. [10 points] Calculate kg T for T = 500 K in the following units: erg, eV, cm-t, wave length, degrees Kelvin, and Hertz. Problem 2. [10 points) The vibrational energy of a diatomic molecule is Ev = ħw(v + 1/2), v= 0, 1, 2, .... For H2, ħw = 4401 cm-7. For 12, ñ w=214.52 cm-7. Without performing a calculation tell which molecule has higher vibrational entropy. Explain your reasoning.
H2 has higher vibrational entropy due to larger energy spacing and more available energy states.
Without performing a calculation, determine which molecule has higher vibrational entropy between H2 and 12, and explain your reasoning?Problem 1:
To calculate kg T for T = 500 K in various units:
[tex]erg: kg T = 1.3807 × 10^-16 erg/K * 500 K eV: kg T = 8.6173 × 10^-5 eV/K * 500 K cm-t: kg T = 1.3807 × 10^-23 cm-t/K * 500 K Wavelength: kg T = (6.626 × 10^-34 J·s) / (500 K) Degrees Kelvin: kg T = 500 K Hertz: kg T = (6.626 × 10^-34 J·s) * (500 Hz)[/tex]
Problem 2:
To determine which molecule has higher vibrational entropy without performing a calculation:
The vibrational entropy (Svib) is directly related to the number of available energy states or levels. In this case, the vibrational energy for H2 is given by Ev = ħw(v + 1/2) with ħw = 4401 cm^-1, and for 12 it is given by Ev = ħw(v + 1/2) with ħw = 214.52 cm^-1.
Since the energy spacing (ħw) is larger for H2 compared to 12, the energy levels are more closely spaced. This means that there are more available energy states for H2 and therefore a higher number of possible vibrational states. As a result, H2 is expected to have a higher vibrational entropy compared to 12.
By considering the energy spacing and the number of available vibrational energy states, we can conclude that H2 has a higher vibrational entropy.
Learn more about entropy
brainly.com/question/32070225
#SPJ11
A planet orbits a star. The period of the rotation of 400 (earth) days. The mass of the star is 6.00 *1030kg. The mass of the planet is 8.00*1022 kg What is the orbital radius?
To determine the orbital radius of the planet, we can use Kepler's third law. The orbital radius of the planet is approximately 4.17 x 10^11 meters.
According to Kepler's third law, the square of the orbital period (T) is proportional to the cube of the orbital radius (r). Mathematically, it can be expressed as T^2 ∝ r^3.
Given that the orbital period of the planet is 400 Earth days, we can convert it to seconds by multiplying it by the conversion factor (1 Earth day = 86400 seconds). Therefore, the orbital period in seconds is (400 days) x (86400 seconds/day) = 34,560,000 seconds.
Now, let's substitute the values into the equation: (34,560,000 seconds)^2 = (orbital radius)^3.
Simplifying the equation, we find that the orbital radius^3 = (34,560,000 seconds)^2. Taking the cube root of both sides, we can find the orbital radius.
Using a calculator, the orbital radius is approximately 4.17 x 10^11 meters. Therefore, the orbital radius of the planet is approximately 4.17 x 10^11 meters.
Learn more about Kepler's third law here; brainly.com/question/30404084
#SPJ11
Calculate the capillary correction of a 100 ml of water (surface
tension = 0.069 N/m) in a 10 mm diameter glass tube. Assume
meniscus angle is 60 degrees.
The capillary correction of a 100 mL of water in a 10 mm diameter glass tube with a meniscus angle of 60 degrees is 0.706 mL.
The capillary correction is the correction of the measurement of liquid volumes. Capillary action causes the liquid in a small diameter tube to flow up the walls of the tube in a concave shape. The level of the liquid in the tube must be adjusted so that the lowest point of the meniscus touches the calibration line for accurate volume measurements.
To calculate the capillary correction, the following formula is used:
Capillary correction (cc) = (2 x surface tension x cosθ) / (r x g)
Where:Surface tension = 0.069 N/m (Given)
Meniscus angle (θ) = 60° (Given)
r = radius of the tube = 10 mm / 2 = 5 mm = 0.005 m
G = acceleration due to gravity = 9.81 m/s²
Capillary correction (cc) = (2 x 0.069 N/m x cos60°) / (0.005 m x 9.81 m/s²)
Capillary correction (cc) = (2 x 0.069 x 0.5) / 0.04905
Capillary correction (cc) = 0.706 mL
Learn more about capillary tube at
https://brainly.com/question/14472773
#SPJ11
Consider a right angled triangle: h=Hyoptenuse a=Adjacent o=opposite Which of the following is true? O h²=o²+ a² 0 √h=√a+√o Oh=o+a Oo=a+h
The correct mathematical representation is h²=o²+ a² . Option A
How to determine the expressionFirst, we need to know that the Pythagorean theorem states that the square of the longest side of a triangle is equal to the sum of the squares of the other two sides of the triangle.
This is expressed as;
h² = o² + a²
Such that the parameters of the formula are given as;
h is the hypotenuse side of the trianglea is the adjacent side of the triangleo is the opposite side of the triangleLearn more about Pythagorean theorem at: https://brainly.com/question/343682
#SPJ4
For questions 5, 6, and 7 calculate the shortest distance in degrees of latitude or longitude (as appropriate) between the two locations given in the question. In other words, how far apart are the given locations in degrees? If minutes or minutes and seconds are given for the locations as well as degrees, provide the degrees and minutes, or degrees, minutes, and seconds for your answer. For example, the answer for question 7 should contain degrees, minutes, and seconds, whereas 5 will have only degrees as part of the answer Question 5 55'W and 55°E QUESTION 6 6. 45°45'N and 10°15'S QUESTION 7 7. 22°09'33"S and 47°51'34"S
The shortest distance in degrees of longitude between 55'W and 55°E is 110 degrees. Thus, the shortest distance in degrees of longitude between the two locations is 110 degrees.
To calculate the shortest distance in degrees of longitude, we need to find the difference between the longitudes of the two locations. The maximum longitude value is 180 degrees, and both the 55'W and 55°E longitudes fall within this range.
55'W can be converted to decimal degrees by dividing the minutes value (55) by 60 and subtracting it from the degrees value (55):
55 - (55/60) = 54.917 degrees
The distance between 55'W and 55°E can be calculated as the absolute difference between the two longitudes:
|55°E - 54.917°W| = |55 + 54.917| = 109.917 degrees
However, since we are interested in the shortest distance, we consider the smaller arc, which is the distance from 55°E to 55°W or from 55°W to 55°E. Thus, the shortest distance in degrees of longitude between the two locations is 110 degrees.
The shortest distance in degrees of longitude between 55'W and 55°E is 110 degrees.
To know more about longitude ,visit:
https://brainly.com/question/31389985
#SPJ11
A thin metal rod of mass 1.7 kg and length 0.9 m is at rest in outer space, near a space station (see figure below). A tiny meteorite with mass 0.09 kg traveling at a high speed of 245 m/s strikes the rod a distance 0.2 m from the center and bounces off with speed 60 m/s as shown in the diagram. The magnitudes of the initial and final angles to the x axis of the small mass's velocity are thetai = 26° and thetaf = 82°. (a) Afterward, what is the velocity of the center of the rod? (Express your answer in vector form.) vCM = m/s (b) Afterward, what is the angular velocity of the rod? (Express your answer in vector form.) = rad/s (c) What is the increase in internal energy of the objects? J
The velocity of the center of the rod in vector form is approximately 24.85 m/s. The angular velocity of the rod after the collision is 24844.087 rad/s. The increase in internal energy of the objects is -103.347 J.
(a) Velocity of center of the rod: The velocity of the center of the rod can be calculated by applying the principle of conservation of momentum. Since the system is isolated, the total momentum of the system before the collision is equal to the total momentum of the system after the collision. Using this principle, the velocity of the center of the rod can be calculated as follows:
Let v be the velocity of the center of the rod after the collision.
m1 = 1.7 kg (mass of the rod)
m2 = 0.09 kg (mass of the meteorite)
v1 = 0 m/s (initial velocity of the rod)
u2 = 245 m/s (initial velocity of the meteorite)
i1 = 0° (initial angle of the rod)
i2 = 26° (initial angle of the meteorite)
j1 = 0° (final angle of the rod)
j2 = 82° (final angle of the meteorite)
v2 = 60 m/s (final velocity of the meteorite)
The total momentum of the system before the collision can be calculated as follows: p1 = m1v1 + m2u2p1 = 1.7 kg × 0 m/s + 0.09 kg × 245 m/sp1 = 21.825 kg m/s
The total momentum of the system after the collision can be calculated as follows: p2 = m1v + m2v2p2 = 1.7 kg × v + 0.09 kg × 60 m/sp2 = (1.7 kg)v + 5.4 kg m/s
By applying the principle of conservation of momentum: p1 = p221.825 kg m/s = (1.7 kg)v + 5.4 kg m/sv = (21.825 kg m/s - 5.4 kg m/s)/1.7 kg v = 10.015 m/s
To represent the velocity in vector form, we can use the following equation:
vCM = (m1v1 + m2u2 + m1v + m2v2)/(m1 + m2)
m1 = 1.7 kg (mass of the rod)
m2 = 0.09 kg (mass of the meteorite)
v1 = 0 m/s (initial velocity of the rod)
u2 = 245 m/s (initial velocity of the meteorite)
v = 10.015 m/s (velocity of the rod after the collision)
v2 = 60 m/s (velocity of the meteorite after the collision)
Substituting these values into the equation, we have:
vCM = (1.7 kg * 0 m/s + 0.09 kg * 245 m/s + 1.7 kg * 10.015 m/s + 0.09 kg * 60 m/s) / (1.7 kg + 0.09 kg)
Simplifying the equation:
vCM = (0 + 22.05 + 17.027 + 5.4) / 1.79
vCM = 44.477 / 1.79
vCM ≈ 24.85 m/s
Therefore, the velocity of the center of the rod in vector form is approximately 24.85 m/s.
(b) Angular velocity of the rod: To calculate the angular velocity of the rod, we can use the principle of conservation of angular momentum. Since the system is isolated, the total angular momentum of the system before the collision is equal to the total angular momentum of the system after the collision. Using this principle, the angular velocity of the rod can be calculated as follows:
Let ω be the angular velocity of the rod after the collision.I = (1/12) m L2 is the moment of inertia of the rod about its center of mass, where L is the length of the rod.m = 1.7 kg is the mass of the rod
The angular momentum of the system before the collision can be calculated as follows:
L1 = I ω1 + m1v1r1 + m2u2r2L1 = (1/12) × 1.7 kg × (0.9 m)2 × 0 rad/s + 1.7 kg × 0 m/s × 0.2 m + 0.09 kg × 245 m/s × 0.7 mL1 = 27.8055 kg m2/s
The angular momentum of the system after the collision can be calculated as follows:
L2 = I ω + m1v r + m2v2r2L2 = (1/12) × 1.7 kg × (0.9 m)2 × ω + 1.7 kg × 10.015 m/s × 0.2 m + 0.09 kg × 60 m/s × 0.7 mL2 = (0.01395 kg m2)ω + 2.1945 kg m2/s
By applying the principle of conservation of angular momentum:
L1 = L2ω1 = (0.01395 kg m2)ω + 2.1945 kg m2/sω = (ω1 - 2.1945 kg m2/s)/(0.01395 kg m2)
Here,ω1 is the angular velocity of the meteorite before the collision. ω1 = u2/r2
ω1 = 245 m/s ÷ 0.7 m
ω1 = 350 rad/s
ω = (350 rad/s - 2.1945 kg m2/s)/(0.01395 kg m2)
ω = 24844.087 rad/s
The angular velocity of the rod after the collision is 24844.087 rad/s.
(c) Increase in internal energy of the objects
The increase in internal energy of the objects can be calculated using the following equation:ΔE = 1/2 m1v1² + 1/2 m2u2² - 1/2 m1v² - 1/2 m2v2²
Here,ΔE is the increase in internal energy of the objects.m1v1² is the initial kinetic energy of the rod.m2u2² is the initial kinetic energy of the meteorite.m1v² is the final kinetic energy of the rod. m2v2² is the final kinetic energy of the meteorite.Using the given values, we get:
ΔE = 1/2 × 1.7 kg × 0 m/s² + 1/2 × 0.09 kg × (245 m/s)² - 1/2 × 1.7 kg × (10.015 m/s)² - 1/2 × 0.09 kg × (60 m/s)²ΔE = -103.347 J
Therefore, the increase in internal energy of the objects is -103.347 J.
Learn more about energy at: https://brainly.com/question/2003548
#SPJ11