The coefficient of kinetic friction between the box and the surface is 0.35.
To determine the coefficient of kinetic friction, we can use the equation:
fₐ= μk.N
where fₐ is the force of kinetic friction, ( μk ) is the coefficient of kinetic friction, and N is the normal force.
In this case, the normal force is equal to the weight of the box, since it is on a flat surface and there is no vertical acceleration. The weight can be calculated as:
N = m. g
where m is the mass of the box and g is the acceleration due to gravity.
Given that the force required to slide the box at a constant velocity is 185 N, the mass of the box is 50 kg, and the acceleration due to gravity is approximately, we can substitute these values into the equation to solve
185N= μ k ⋅(50kg⋅9.8m/s 2 )
Simplifying:
= 185N 50kg⋅9.8m/s2
=0.375 μ k
= 50kg⋅9.8m/s 2 185N
= 0.375
Therefore, the coefficient of kinetic friction between the box and the surface is approximately 0.375.
To learn more about friction click here brainly.com/question/13000653
#SPJ11
A m= 5,400 kg trailer with two axles separated by a distance L = 9.4 m has the center of gravity at d = 4.5 m from the front axle. How far from the rear axle should the center of gravity of a M = 2,000 kg load be placed so that the same normal force acts on the front and rear axles?
The center of gravity of the load should be placed at a distance of 5.8 m from the rear axle.
In the case of a vehicle with a trailer, the distribution of the load is critical for stability. In general, it is recommended that the heaviest items be placed in the center of the trailer, as this will help to maintain stability.The normal force is the weight force, which is represented by the force that the load applies to the axles, and is equal to the product of the mass and the acceleration due to gravity. Thus, to maintain stability, the center of gravity of the load must be placed at a certain distance from the rear axle.Let the distance from the rear axle to the center of gravity of the load be x. Then, the weight of the load will be given by:
Mg = F1 + F2
Here, F1 is the normal force acting on the front axle, and F2 is the normal force acting on the rear axle. Since the same normal force acts on both axles, F1 = F2.
Therefore, Mg = 2F1or F1 = Mg/2
Now, let us calculate the weight that acts on the front axle:
W1 = mF1g
where W1 is the weight of the trailer that acts on the front axle, and m is the mass of the trailer. Similarly, the weight that acts on the rear axle is:
W2 = mF2g = mF1g
Thus, to maintain balance, the center of gravity of the load must be placed at a distance of x from the rear axle, such that: W2x = W1(d - x)
where d is the distance between the axles. Substituting the values given, we get:
W2x = W1(d - x)2000*9.81*x
= (5400+2000)*9.81(9.4 - x + 4.5)x = 5.8 m
Therefore, the center of gravity of the load should be placed at a distance of 5.8 m from the rear axle.
To learn more about gravity visit;
https://brainly.com/question/31321801
#SPJ11
At a particular place on the surface of the Earth, the Earth's magnetic field has magnitude of 5.45 x 109T, and there is also a 121 V/m electric field perpendicular to the Earth's surface ) Compute the energy density of the electric field (Give your answer in l/m /m (b) Compute the energy density of the magnetic field. (Give your answer in wm. /m2
The energy density of the magnetic field is 2.5 x 10^4 J/m³.
(a) Energy density of electric field
The energy density of the electric field is given by the formula;
u = 1/2εE²
Where
u is the energy density of the electric field,
ε is the permittivity of the medium and
E is the electric field strength.
The energy density of electric field can be computed as follows;
Given:
Electric field strength, E = 121 V/m
The electric field strength is perpendicular to the Earth's surface, which means it is acting on a vacuum where the permittivity of free space is:
ε = 8.85 x 10^-12 F/m
Therefore;
u = 1/2εE²
u = 1/2(8.85 x 10^-12 F/m)(121 V/m)²
u = 7.91 x 10^-10 J/m³
Hence, the energy density of the electric field is 7.91 x 10^-10 J/m³.
(b) Energy density of magnetic field
The energy density of the magnetic field is given by the formula;
u = B²/2μ
Where
u is the energy density of the magnetic field,
B is the magnetic field strength and
μ is the permeability of the medium.
The energy density of magnetic field can be computed as follows;
Given:
Magnetic field strength, B = 5.45 x 10⁹ T
The magnetic field strength is perpendicular to the Earth's surface, which means it is acting on a vacuum where the permeability of free space is:
μ = 4π x 10^-7 H/m
Therefore;
u = B²/2μ
u = (5.45 x 10⁹ T)²/2(4π x 10^-7 H/m)
u = 2.5 x 10^4 J/m³
Hence, the energy density of the magnetic field is 2.5 x 10^4 J/m³.
Learn more about magnetic field from this link:
https://brainly.com/question/24761394
#SPJ11
As has focal length 44 cm Part A Find the height of the image produced when a 22 cas high obard is placed at stance +10 cm Express your answer in centimeters
The height of the image is 58.74 cm.
Given data:
Focal length = 44 cm
Height of object = 22 cm
Object distance (u) = -10 cm
Image distance (v) =?
Formula: Using the lens formula `1/f = 1/v - 1/u`,
Find the image distance (v).
Using the magnification formula m = -v/u`,
Find the magnification (m).
Using the magnification formula m = h₂/h₁`,
Find the height of the image (h₂).
As per the formula, `
1/f = 1/v - 1/u`
1/44 = 1/v - 1/(-10)
1/v =1/44 + 1/10
v = 26.7 cm.
The image distance (v) is 26.7 cm.
As per the formula, `m = -v/u`
m = -26.7/-10
m = 2.67.
The magnification is 2.67.
As per the formula, `m = h₂/h₁`
2.67 = h₂/22
h₂ = 58.74 cm.
Therefore The height of the image is 58.74 cm.
Learn more about height and Focal length https://brainly.com/question/28039799
#SPJ11
Louis de Broglie's bold hypothesis assumes that it is possible to assign a wavelength λ to every particle possessing some momentum p by the relationship λ=ph, where h is Planck's constant (h=6.626×10−34 J⋅S). To help you develop some number sense for what this relationship means, try below calculations. You may find these two constants useful: Planck's constant h=6.626×10−34 J⋅s and electron mass 9.109×10−31 kg. a. The de Broglie wavelength of an electron moving at speed 4870 m/s is nm. (This speed corresponds to thermal speed of an electron that has been cooled down to about 1 kelvin.) b. The de Broglie wavelength of an electron moving at speed 610000 m/s is nm. (This speed corresponds to the speed of an electron with kinetic energy of about 1eV.) c. The de Broglie wavelength of an electron moving at speed 17000000 m/s is nm. (At speeds higher than this, we will need to start accounting for effects of specialurelativity to avoid significant (greater than a few percents) errors in calculation.) Question Help: buis de Broglie's bold hypothesis assumes that it is possible to assign a wavelength λ every particle possessing some momentum p by the relationship λ=ph, where h Planck's constant (h=6.626×1034 J⋅s). This applies not only to subatomic articles like electrons, but every particle and object that has a momentum. To help ou develop some number sense for de Broglie wavelengths of common, everyday bjects, try below calculations. Use Planck's constant h=6.626×10−34 J⋅s; other necessary constants will be given below. To enter answers in scientific notation below, use the exponential notation. For example, 3.14×10−14 would be entered as "3.14E-14". a. Air molecules (mostly oxygen and nitrogen) move at speeds of about 270 m/s. If mass of air molecules are about 5×10−26 kg, their de Broglie wavelength is m. b. Consider a baseball thrown at speed 50 m/s. If mass of the baseball is 0.14 kg, its de Broglie wavelength is c. The Earth orbits the Sun at a speed of 29800 m/s. Given that the mass of the Earth is about 6.0×1024 kg, its de Broglie wavelength is Yes, many of these numbers are absurdly small, which is why I think you should enter the powers of 10. Question Help: □ Message instructor
a. The de Broglie wavelength of an electron moving at a speed of 4870 m/s is approximately 2.72 nanometers (2.72 nm).
b. The de Broglie wavelength of an electron moving at a speed of 610,000 m/s is approximately 0.022 nanometers (0.022 nm).
c. The de Broglie wavelength of an electron moving at a speed of 17,000,000 m/s is approximately 0.00077 nanometers (0.00077 nm).
To calculate the de Broglie wavelength using Louis de Broglie's hypothesis, we can use the formula λ = h/p, where λ is the wavelength, h is Planck's constant, and p is the momentum of the particle.
a. For an electron moving at a speed of 4870 m/s:
Given:
Speed of the electron (v) = 4870 m/s
To find the momentum (p) of the electron:
Momentum (p) = mass (m) * velocity (v)
Given:
Mass of the electron (m) = 9.109×10^−31 kg
Substituting the values:
p = (9.109×10^−31 kg) * (4870 m/s)
Using the de Broglie wavelength formula:
λ = h/p
Substituting the values:
λ = (6.626×10^−34 J·s) / [(9.109×10^−31 kg) * (4870 m/s)]
Calculating the de Broglie wavelength:
λ ≈ 2.72 × 10^−9 m ≈ 2.72 nm
b. For an electron moving at a speed of 610,000 m/s:
Given:
Speed of the electron (v) = 610,000 m/s
To find the momentum (p) of the electron:
Momentum (p) = mass (m) * velocity (v)
Given:
Mass of the electron (m) = 9.109×10^−31 kg
Substituting the values:
p = (9.109×10^−31 kg) * (610,000 m/s)
Using the de Broglie wavelength formula:
λ = h/p
Substituting the values:
λ = (6.626×10^−34 J·s) / [(9.109×10^−31 kg) * (610,000 m/s)]
Calculating the de Broglie wavelength:
λ ≈ 2.2 × 10^−11 m ≈ 0.022 nm
c. For an electron moving at a speed of 17,000,000 m/s:
Given:
Speed of the electron (v) = 17,000,000 m/s
To find the momentum (p) of the electron:
Momentum (p) = mass (m) * velocity (v)
Mass of the electron (m) = 9.109×10^−31 kg
Substituting the values:
p = (9.109×10^−31 kg) * (17,000,000 m/s)
Using the de Broglie wavelength formula:
λ = h/p
Substituting the values:
λ = (6.626×10^−34 J·s) / [(9.109×10^−31 kg) * (17,000,000 m/s)]
Calculating the de Broglie wavelength:
λ ≈ 7.7 × 10^−13 m ≈ 0.00077 nm
The de Broglie wavelength of an electron moving at
To know more about de Broglie wavelength ,visit:
https://brainly.com/question/30404168
#SPJ11
Comparing the radiation power loss for electron ( Pe )
with radiation power loss for the proton ( Pp ) in the synchrotron,
one gets :
1- Pe = Pp = 0
2- Pe << Pp
3- Pe >> Pp
4- Pe ≈ Pp
When comparing the radiation power loss for electrons (Pe) and protons (Pp) in a synchrotron, the correct answer is 2- Pe << Pp. This means that the radiation power loss for electrons is much smaller than that for protons.
The radiation power loss in a synchrotron occurs due to the acceleration of charged particles. It depends on the mass and charge of the particles involved.
Electrons have a much smaller mass compared to protons but carry the same charge. Since the radiation power loss is proportional to the square of the charge and inversely proportional to the square of the mass, the power loss for electrons is significantly smaller than that for protons.
Therefore, option 2- Pe << Pp is the correct choice, indicating that the radiation power loss for electrons is much smaller compared to that for protons in a synchrotron.
Learn more about synchrotron here:
brainly.com/question/31070723
#SPJ11
5.0-C charge experiences a 0.58-N force in the positive y rection Part A If this charge is replaced with a -2.7μC charge, what is the magnitude of the force will it experience? Express your answer u
If the charge is replaced , it will experience a force in the negative y-direction. The magnitude of the force can be calculated using Coulomb's Law.
Coulomb's Law states that the force between two charges is given by the equation:
F = k * |q1 * q2| / r^2where F is the force, k is the electrostatic constant, q1 and q2 are the charges, and r is the distance between the charges.
Given:
q1 = 0 C (initial charge)
F1 = 0.58 N (force experienced by the initial charge)
To find the magnitude of the force when the charge is replaced with -2.7 μC, we can use the ratio of the charges to calculate the new force:F2 = (q2 / q1) * F1
Converting -2.7 μC to coulombs:
q2 = -2.7 μC * (10^-6 C/1 μC)
q2 = -2.7 * 10^-6 C
Substituting the values into the equation:
F2 = (-2.7 * 10^-6 C / 0 C) * 0.58 N
Calculating the magnitude of the force:
F2 ≈ -1.566 * 10^-6 N
Therefore, if the charge is replaced with a -2.7 μC charge, it will experience a force of approximately 1.566 * 10^-6 N in the negative y-direction.
To know more about Coulomb's Law click here.
brainly.com/question/506926
#SPJ11
A solenoid of radius 2.60 cm has 490 turns and a length of 17.0 cm.
(a) Find its inductance.
(b) Find the rate at which current must change through it to produce an emf of 55.0 mV.
The inductance of the solenoid is approximately 0.376 H. This value is obtained using the formula L = (μ₀ * N² * A) / l, where μ₀ is the permeability of free space, N is the number of turns, A is the cross-sectional area, and l is the length of the solenoid.
To produce an emf of 55.0 mV, the current through the solenoid must change at a rate of approximately 146.3 A/s. This rate is determined by the formula ε = -L * (dI/dt), where ε is the induced emf and dI/dt is the rate of change of current with respect to time. The negative sign indicates a decrease in current.
Learn more about solenoid
https://brainly.com/question/21842920
#SPJ11
972 Two bodies of masses ma and my undergo a perfectly elastic collision that is central (head-on). Both are moving in opposite directions along the same straight line before collision with velocities vai and VBI. (Call all v's +) (a) Find the velocity of each body after the collision, in terms of the masses and the velocities given. (b) For the special case in which B is at rest before collision, find the ratio kinetic energy of_B_after_collision K= , in terms of (m/m). kinetic_energy_of_A_before_collision (c) Letr stand for the ratio (m/m). Find the value of that's makes K(r) a maximum. What does me have to be in terms of mx) for the maximum transfer of kinetic energy in the collision? (Would you have guessed this without working it out?). Notice why much more energy is transferred when an electron collides with another electron than when an electron collides with an atom ("Interacts" would be a little more accurate than "collides.") Can you see what a graph of K(T) vs. r looks like?
(a) The velocity of each body after the collision can be calculated using the conservation of momentum and kinetic energy.
ma * vai + mb * vbi = ma * vaf + mb * vbf
(1/2) * ma * (vai)^2 + (1/2) * mb * (vbi)^2 = (1/2) * ma * (vaf)^2 + (1/2) * mb * (vbf)^2
(b) For the special case where B is at rest before the collision (vbi = 0), we can simplify the expressions:
vaf = vai * (mb / (ma + mb))
vbf = vai * (ma / (ma + mb))
K = (1/2) * mb * (vbf)^2 / ((1/2) * ma * (vai)^2)
K = (mb^2 / (ma + mb)^2) * (ma / ma)
K = mb^2 / (ma + mb)^2
(c) To find the value of r that maximizes K, we need to differentiate K with respect to r and set it to zero:
dK/dr = 0
K = mb^2 / (ma + mb)^2 with respect to r:
dK/dr = -2 * mb^2 / (ma + mb)^3 + 2 * mb^2 * ma / (ma + mb)^4
dK/dr to zero and solving for r:
-2 * mb^2 / (ma + mb)^3 + 2 * mb^2 * ma / (ma + mb)^4 = 0
Therefore, for the maximum transfer of kinetic energy in the collision, the mass of A (me) needs to be equal to the mass of B (mx).
Learn more about momentum here : brainly.com/question/30677308
#SPJ11
In a hydrogen atom, a given electron has l=7. So just how many
values can the magnetic quantum number have?
(please type the answer, Thank you)
The magnetic quantum number (ml) can have 15 values in the given condition where a given electron in a hydrogen atom has l = 7
The magnetic quantum number (ml) determines the direction of the angular momentum vector. It indicates the orientation of the orbital in space.
Magnetic quantum number has the following values for a given electron in a hydrogen atom:
ml = - l, - l + 1, - l + 2,...., 0,....l - 2, l - 1, l
The range of magnetic quantum number (ml) is from –l to +l. As given, l = 7
Therefore,
ml = -7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
In this case, the magnetic quantum number (ml) can have 15 values.
Learn more about magnetic quantum number: https://brainly.com/question/21760208
#SPJ11
25. What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2,165-kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.2cm diameter and the slave has a 27-cm diameter.
To support the weight of a 2,165-kg car on the slave cylinder of a hydraulic lift, a force of approximately 15,674.55 N must be exerted on the master cylinder.
This can be calculated using Pascal's law and the principle of hydraulic pressure, considering the ratio of the areas of the master and slave cylinders.
According to Pascal's law, pressure exerted on a fluid is transmitted uniformly in all directions. In a hydraulic system, the pressure applied to the master cylinder is transmitted to the slave cylinder, allowing for a mechanical advantage.
To find the force required on the master cylinder, we need to compare the areas of the master and slave cylinders. The area of a cylinder is given by A = πr^2, where r is the radius of the cylinder.
Given the diameter of the master cylinder as 2.2 cm, the radius is 1.1 cm (0.011 m), and the area is approximately 0.000379 m^2. Similarly, the diameter of the slave cylinder is 27 cm, giving a radius of 13.5 cm (0.135 m) and an area of approximately 0.057 m^2.
Since pressure is the force per unit area, we can calculate the force on the master cylinder by multiplying the area ratio by the weight of the car. The area ratio is the slave cylinder area divided by the master cylinder area.
Therefore, the force on the master cylinder is approximately 0.057 m^2 / 0.000379 m^2 * 2,165 kg * 9.8 m/s^2 = 15,674.55 N. This force must be exerted on the master cylinder to support the weight of the car on the hydraulic lift
To learn more about, force:-
brainly.com/question/30507236
#SPJ11
In an electric shaver, the blade moves back and forth over a distance of 2.0 mm in simple harmonic motion, with frequency 100Hz. Find 1.The amplitude 2.The maximum blade speed 3. The magnitude of the maximum blade acceleration
The amplitude of the blade's simple harmonic motion is 1.0 mm (0.001 m). The maximum blade speed is approximately 0.628 m/s. The magnitude of the maximum blade acceleration is approximately 1256.64 m/s².
The amplitude, maximum blade speed, and magnitude of maximum blade acceleration in the electric shaver:
1. Amplitude (A): The amplitude of simple harmonic motion is equal to half of the total distance covered by the blade. In this case, the blade moves back and forth over a distance of 2.0 mm, so the amplitude is 1.0 mm (or 0.001 m).
2. Maximum blade speed (V_max): The maximum blade speed occurs at the equilibrium position, where the displacement is zero. The maximum speed is given by the product of the amplitude and the angular frequency (ω).
V_max = A * ω
The angular frequency (ω) can be calculated using the formula ω = 2πf, where f is the frequency. In this case, the frequency is 100 Hz.
ω = 2π * 100 rad/s = 200π rad/s
V_max = (0.001 m) * (200π rad/s) ≈ 0.628 m/s
3. Magnitude of maximum blade acceleration (a_max): The maximum acceleration occurs at the extreme positions of the motion, where the displacement is maximum. The magnitude of maximum acceleration is given by the product of the square of the angular frequency (ω^2) and the amplitude (A).
a_max = ω² * A
a_max = (200π rad/s)² * 0.001 m ≈ 1256.64 m/s²
Learn more about ”harmonic motion” here:
brainly.com/question/26114128
#SPJ11
3. What would happen if you put an object at the focal point of the lens? 4. What would happen if you put an object at the focal point of the mirror? 5. What would happen if you put an object between the focal point and the lens? 6. What would happen if you put an object between the focal point and the mirror?
The specific placement of an object relative to the focal point of a lens or mirror determines the characteristics of the resulting image, such as its nature (real or virtual), size, and orientation.
Let's provide a more detailed explanation for each scenario:
3. Placing an object at the focal point of a lens:
When an object is placed exactly at the focal point of a lens, the incident rays from the object become parallel to each other after passing through the lens. This occurs because the lens refracts (bends) the incoming rays in such a way that they converge at the focal point on the opposite side. However, when the object is positioned precisely at the focal point, the refracted rays become parallel and do not converge to form a real image. Therefore, in this case, no real image is formed on the other side of the lens.
4. Placing an object at the focal point of a mirror:
If an object is positioned at the focal point of a mirror, the reflected rays will appear to be parallel to each other. This happens because the light rays striking the mirror surface are reflected in a way that they diverge as if they were coming from the focal point behind the mirror. Due to this divergence, the rays never converge to form a real image. Instead, the reflected rays appear to originate from a virtual image located at infinity. Consequently, no real image can be projected onto a screen or surface.
5. Placing an object between the focal point and the lens:
When an object is situated between the focal point and a converging lens, a virtual image is formed on the same side as the object. The image appears magnified and upright. The lens refracts the incoming rays in such a way that they diverge after passing through the lens. The diverging rays extend backward to intersect at a point where the virtual image is formed. This image is virtual because the rays do not actually converge at that point. The virtual image is larger in size than the object, making it appear magnified.
6. Placing an object between the focal point and the mirror:
Similarly, when an object is placed between the focal point and a concave mirror, a virtual image is formed on the same side as the object. The virtual image is magnified and upright. The mirror reflects the incoming rays in such a way that they diverge after reflection. The diverging rays appear to originate from a point behind the mirror, where the virtual image is formed. Again, the virtual image is larger than the object and is not a real convergence point of light rays.
In summary, the placement of an object relative to the focal point of a lens or mirror determines the behavior of the light rays and the characteristics of the resulting image. These characteristics include the nature of the image (real or virtual), its size, and its orientation (upright or inverted).
Note: In both cases (5 and 6), the images formed are virtual because the light rays do not actually converge or intersect at a point.
To learn more about focal point, Visit:
https://brainly.com/question/30761313
#SPJ11
A 220-g ball moving at 7.5 m/s collides elastically with a second ball.
initially at rest. Immediately after the collision, the first ball rebounds with a speed of
3.8m/s Determine the speed and mass of the second ball.
The speed and mass of the second ball after the collision are 5.65 m/s and 0.88 kg respectively.
The speed and mass of the second ball after the collision can be determined using the principles of conservation of momentum and conservation of kinetic energy. The formula for the conservation of momentum is given as:
m₁v₁ + m₂v₂ = m₁u₁ + m₂u₂
where, m₁ and m₂ are the masses of the two balls respectively, v₁ and v₂ are the initial velocities of the balls, and u₁ and u₂ are the velocities of the balls after the collision.
The formula for conservation of kinetic energy is given as:0.5m₁v₁² + 0.5m₂v₂² = 0.5m₁u₁² + 0.5m₂u₂²
where, m₁ and m₂ are the masses of the two balls respectively, v₁ and v₂ are the initial velocities of the balls, and u₁ and u₂ are the velocities of the balls after the collision.
Given,
m₁ = 220 g
m = 0.22 kg
v₁ = 7.5 m/s
u₁ = -3.8 m/s (rebounding)
m₂ = ?
v₂ = 0 (initially at rest)
u₂ = ?
The conservation of momentum equation can be written as:
m₁v₁ + m₂v₂ = m₁u₁ + m₂u₂
=> 0.22 × 7.5 + 0 × m₂ = 0.22 × (-3.8) + m₂u₂
=> 1.65 - 0.22u₂ = -0.836 + u₂
=> 0.22u₂ + u₂ = 2.486
=> u₂ = 2.486/0.44= 5.65 m/s
Conservation of kinetic energy equation can be written as:
0.5m₁v₁² + 0.5m₂v₂² = 0.5m₁u₁² + 0.5m₂u₂²
=> 0.5 × 0.22 × 7.5² + 0.5 × 0 × v₂² = 0.5 × 0.22 × (-3.8)² + 0.5 × m₂ × 5.65²
=> 2.475 + 0 = 0.7388 + 1.64m₂
=> m₂ = (2.475 - 0.7388)/1.64= 0.88 kg
Learn more about conservation of kinetic energy: https://brainly.com/question/24301052
#SPJ11
The position of a 51 gg oscillating mass is given by
x(t)=(1.5cm)cos11t, where t is in seconds. Determine the
amplitude.
The given position equation is x(t) = (1.5 cm)cos(11t). In this equation, the coefficient of the cosine function represents the amplitude of the oscillation.
To determine the amplitude of the oscillating mass, we can observe that the equation for position, x(t), is given by:
x(t) = (1.5 cm) * cos(11t)
The amplitude of an oscillating mass is the maximum displacement from the equilibrium position. In this case, the maximum displacement is the maximum value of the cosine function.
The maximum value of the cosine function is 1, so the amplitude of the oscillating mass is equal to the coefficient in front of the cosine function, which is 1.5 cm.
Therefore, the amplitude of the oscillating mass is 1.5 cm.
Learn more about Amplitude here:
brainly.com/question/9525052
#SPJ11
If 3.04 m 3 of a gas initially at STP is placed under a pressure of 2.68 atm, the temperature of the gas rises to 33.3 ∘ C. Part A What is the volume?
The volume of the gas at the given condition is 6.5 m³ given that 3.04 m 3 of a gas initially at STP is placed under a pressure of 2.68 atm and the temperature of the gas rises to 33.3° C.
Given: Initial volume of gas = 3.04 m³
Pressure of the gas = 2.68 ATM
Temperature of the gas = 33.3°C= 33.3 + 273= 306.3 K
As per Gay Lussac's law: Pressure of a gas is directly proportional to its temperature, if the volume remains constant. At constant volume, P ∝ T ⟹ P1/T1 = P2/T2 [Where P1, T1 are initial pressure and temperature, P2, T2 are final pressure and temperature]
At STP, pressure = 1 atm and temperature = 273 K
So, P1 = 1 atm and T1 = 273 K
Now, P2 = 2.68 atm and T2 = 306.3 K
V1 = V2 [Volume remains constant]1 atm/273 K = 2.68 atm/306.3 K
V2 = V1 × (P2/P1) × (T1/T2)
V2 = 3.04 m³ × (2.68 atm/1 atm) × (273 K/306.3 K)
V2 = 6.5 m³
Therefore, the volume of the gas at the given condition is 6.5 m³.
More on gas volume: https://brainly.com/question/22960215
#SPJ11
Using the planet masses and equitorial diameter, determine the
ratio of acceleartion due to gravity on Mars to acceleartion due to
gravity on Venus (to 3 significant figures)?
The planet masses and equatorial diameter, the ratio of acceleration due to gravity on Mars to acceleration due to gravity on Venus is 0.420
To determine the ratio of acceleration due to gravity on Mars to acceleration due to gravity on Venus, we need to compare the gravitational forces experienced on each planet using the following equation:
g = G × (M / r^2)
where:
g is the acceleration due to gravity,
G is the gravitational constant (approximately 6.67430 × 10^-11 m^3/kg/s^2),
M is the mass of the planet, and
r is the radius of the planet.
Given the planet masses and equatorial diameters, we can calculate the acceleration due to gravity on each planet.
For Mars:
Mass of Mars (M_Mars) = 6.39 × 10^23 kg
Equatorial diameter of Mars (d_Mars) = 6792 km = 6792000 m
Radius of Mars (r_Mars) = d_Mars / 2
For Venus:
Mass of Venus (M_Venus) = 4.87 × 10^24 kg
Equatorial diameter of Venus (d_Venus) = 12,104 km = 12104000 m
Radius of Venus (r_Venus) = d_Venus / 2
Now, let's calculate the acceleration due to gravity on each planet:
g_Mars = G × (M_Mars / r_Mars^2)
g_Venus = G × (M_Venus / r_Venus^2)
Finally, we can calculate the ratio of acceleration due to gravity on Mars to acceleration due to gravity on Venus:
Ratio = g_Mars / g_Venus
Now let's calculate these values:
Mass of Mars (M_Mars) = 6.39 × 10^23 kg
Equatorial diameter of Mars (d_Mars) = 6792 km = 6792000 m
Radius of Mars (r_Mars) = 6792000 m / 2 = 3396000 m
Mass of Venus (M_Venus) = 4.87 × 10^24 kg
Equatorial diameter of Venus (d_Venus) = 12,104 km = 12104000 m
Radius of Venus (r_Venus) = 12104000 m / 2 = 6052000 m
Gravitational constant (G) = 6.67430 × 10^-11 m^3/kg/s^2
g_Mars = (6.67430 × 10^-11 m^3/kg/s^2) × (6.39 × 10^23 kg / (3396000 m)^2)
≈ 3.727 m/s^2
g_Venus = (6.67430 × 10^-11 m^3/kg/s^2) × (4.87 × 10^24 kg / (6052000 m)^2)
≈ 8.871 m/s^2
Ratio = g_Mars / g_Venus
≈ 0.420
Therefore, the ratio of acceleration due to gravity on Mars to acceleration due to gravity on Venus is approximately 0.420 (to 3 significant figures).
To learn more about gravitational forces visit: https://brainly.com/question/24783651
#SPJ11
At what temperature will both the reading in Celsius and Fahrenheit read the same value? Show your calculations.
The temperature at which both the Celsius and Fahrenheit scales read the same value is -40 °C/°F.
The Celsius temperature scale is used by most of the world, while the Fahrenheit scale is used primarily in the United States. The formula to convert Fahrenheit to Celsius is C = (5/9)(F - 32), and the formula to convert Celsius to Fahrenheit is F = (9/5)C + 32.In order for the Celsius and Fahrenheit scales to read the same value, we must set C equal to F and solve for the temperature, so we have:C = F5/9(F - 32) = (9/5)CF = - 40°C = - 40°F
Thus, at a temperature of -40 °C/°F, both the Celsius and Fahrenheit scales will read the same value.Calculations:As per the formula,F = (9/5)C + 32Putting C = F, we get;C = (9/5)C + 32C - (9/5)C = 32-4/5C = 32C = - 40Therefore, both the Celsius and Fahrenheit scales read the same value at -40 °C/°F.
To know more about temperature visit:
https://brainly.com/question/15809796
#SPJ11
Burl and Paul have a total weight of 688 N. The tensions in the ropes that support the scaffold they stand on add to 1448 N. Determine the weight of the scaffold (N). (Note: Be sure to report answer with the abbreviated form of the unit.)
The weight of the scaffold is 1208 N.
Given Data: Burl and Paul have a total weight of 688 N.
Tensions in the ropes that support the scaffold they stand on add to 1448 N.
Formula Used: The weight of the scaffold can be calculated by using the formula given below:
Weight of the Scaffold = Tension on Left + Tension on Right - Total Weight of Burl and Paul
Weight of the Scaffold = Tension L + Tension R - (Burl + Paul)
So the weight of the scaffold is 1208 N. (Note: Be sure to report answer with the abbreviated form of the unit.)
Learn more about Weight
https://brainly.com/question/31659519
#SPJ11
(a) For an object distance of 49.5 cm, determine the following. What are the image distance and image location with respect to the lens? (Give the magnitude of the distance in cm.) image distance cm image location in front of the lens Is the image real or virtual? virtual What is the magnification? Is the image upright or inverted? upright (b) For an object distance of P2 = 14.9 cm, determine the following. What are the image distance and image location with respect to the lens? (Give the magnitude of the distance in cm.) image distance image location in front of the lens cm Is the image real or virtual? virtual What is the magnification? Is the image upright or inverted? upright (C) For an object distance of P3 = 29.7 cm, determine the following. What are the image distance and image location with respect to the lens? (Give the magnitude of the distance in cm.) image distance cm image location in front of the lens Is the image real or virtual? virtual What is the magnification?
An object distance of 49.5 cm creates a virtual image located 1 cm in front of the lens, with a magnification of -1.An object distance of 14.9 cm creates a virtual image located 7.45 cm in front of the lens, with a magnification of -1.5.An object distance of 29.7 cm creates a virtual image located 1 cm in front of the lens, with a magnification of -1.
For an object distance of 49.5 cm, Image distance = -49.5 cm, image location = 1 cm in front of the lens, magnification = -1.The negative sign indicates that the image is virtual, upright, and diminished. When the image distance is negative, it is virtual, and when it is positive, it is real.
When the magnification is negative, the image is inverted, and when it is positive, it is upright.
An object distance of 49.5 cm creates a virtual image located 1 cm in front of the lens, with a magnification of -1.
For an object distance of P2 = 14.9 cm, tImage distance = -22.35 cm, image location = 7.45 cm in front of the lens, magnification = -1.5.
The negative sign indicates that the image is virtual, upright, and magnified. When the image distance is negative, it is virtual, and when it is positive, it is real. When the magnification is negative, the image is inverted, and when it is positive, it is upright.
An object distance of 14.9 cm creates a virtual image located 7.45 cm in front of the lens, with a magnification of -1.5.
For an object distance of P3 = 29.7 cm, Image distance = -29.7 cm, image location = 1 cm in front of the lens, magnification = -1.
The negative sign indicates that the image is virtual, upright, and of the same size as the object. When the image distance is negative, it is virtual, and when it is positive, it is real. When the magnification is negative, the image is inverted, and when it is positive, it is upright.
An object distance of 29.7 cm creates a virtual image located 1 cm in front of the lens, with a magnification of -1.
To know more about magnification visit:
brainly.com/question/21370207
#SPJ11
Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 19 minutes. The density of air is 1.20 kg/m 3
. Determine the drag force on the runner during the race. Suppose that the runner has the cross section area of 0.72 m 2 and the drag coefficient of 1.2. Express your answer with the appropriate units. What is this force as a fraction of the runner's weight? Express your answer numerically.
The drag force on the runner during the race is determined to be a certain value, and its relationship to the runner's weight is calculated as a fraction.
The drag force experienced by the runner can be calculated using the formula:
F = (1/2) * ρ * A * Cd * v^2
Where F is the drag force, ρ is the density of air, A is the cross-sectional area of the runner, Cd is the drag coefficient, and v is the velocity of the runner.
Given the values: ρ = 1.20 kg/m^3, A = 0.72 m^2, Cd = 1.2, and the runner's velocity can be determined from the race distance and time. The velocity is calculated by dividing the distance by the time:
v = distance / time = 5.0 km / 19 minutes
Once the velocity is known, it can be substituted into the drag force formula to calculate the value of the drag force.To determine the drag force as a fraction of the runner's weight, we can divide the drag force by the weight of the runner. The weight of the runner can be calculated as the mass of the runner multiplied by the acceleration due to gravity (g = 9.8 m/s^2).
Finally, the calculated drag force as a fraction of the runner's weight can be expressed numerically.
Therefore, the drag force on the runner during the race can be determined, and its relationship to the runner's weight can be expressed as a fraction numerically.
Learn more about drag force here:
https://brainly.com/question/14748915
#SPJ11
(A=4, C=2) \) Use the principle of superposition to determine the resulting waveform when the waves in figure interfere with each other."
The resulting waveform will have a displacement equal to the sum of their individual displacements at each point.
When waves interfere with each other,
The principle of superposition states that the displacement of the resulting waveform at any point is equal to the algebraic sum of the individual displacements caused by each wave at that point.
In this case, we have two waves, one represented by Figure A and the other by Figure C.
Assuming these waves are traveling in the same medium and have the same frequency, we can determine the resulting waveform by adding the individual displacements at each point.
Let's consider a point in space and time where both waves overlap.
If the amplitude of the wave in Figure A is 4 and the amplitude of the wave in Figure C is 2,
The resulting waveform at that point will have a displacement equal to the sum of the individual displacements, which is
4 + 2 = 6.
The resulting waveform will have a shape and wavelength determined by the characteristics of the individual waves.
The exact form of the resulting waveform will depend on the phase relationship between the waves, which is not specified in the given information.
When the waves in Figure A and Figure C interfere, the resulting waveform will have a displacement equal to the sum of their individual displacements at each point.
The specific shape and wavelength of the resulting waveform will depend on the characteristics and phase relationship of the individual waves.
Learn more about Superposition from the given link :
https://brainly.com/question/29518396
#SPJ11
A wire has a resistivitiy of 3.00×10 −8
Ωm with a diameter of 600 mm and length of 20,0 m. A) What is the resistance of the wire B) With a 12.0 V battery connected across the ends of the wire, find the current in the wire? c) What is the power loss in the wire?
The resistance of the wire is 6.33 Ω.The current in the wire when a 12.0 V battery is 1.90A..the power loss in the wire is 22.9 W.
The resistance of the wire The resistance of the wire is given by:
R = ρL/A where;ρ is the resistivity of the wire, A is the cross-sectional area of the wire and L is the length of the wire. Substituting the given values,
R = ([tex]3.00 \times 10^{-8}[/tex] Ωm × 20.0 m) / [(π / 4) × (0.6 m)²],
R = 6.33 Ω.
The current in the wire when a 12.0 V battery is connected is given by:I = V/R where;V is the voltage across the wire and R is the resistance of the wire.
Substituting the given values,
I = 12 V / 6.33 Ω.
I = 1.90 A.
Power loss in the wireWhen current flows through a wire, energy is dissipated in the form of heat due to the resistance of the wire. The power loss in the wire is given by:P = I²R where;I is the current through the wire and R is the resistance of the wire.Substituting the given values, P = (1.90 A)² × 6.33 Ω = 22.9 W,
A wire with a resistivity of [tex]3.00 \times 10^{-8}[/tex] Ωm, a diameter of 600 mm and a length of 20.0 m has a resistance of 6.33 Ω. When a 12.0 V battery is connected across the ends of the wire, the current in the wire is 1.90 A. The power loss in the wire is 22.9 W.
The power loss in a wire can be calculated using the formula P = I²R where P is the power loss, I is the current flowing through the wire and R is the resistance of the wire. Alternatively, the power loss can be calculated using the formula P = V²/R where V is the voltage across the wire.
This formula is obtained by substituting Ohm's law V = IR into the formula P = I²R. The power loss in a wire can also be calculated using Joule's law, which states that the power loss is proportional to the square of the current flowing through the wire.
Thus, the power loss in the wire is 22.9 W.
To know more about resistance visit:
brainly.com/question/33728800
#SPJ11
Remaining Time: 24 minutes, 43 seconds. Question Completion Status: Question 2 0.5 points Save Answe A battery of 8-13 V is connected to a load resistor R-60. If the terminal voltage across the batter
Answer:
The terminal voltage across the battery is 7-13 V.
Explanation:
The terminal voltage of a battery is the voltage measured across its terminals when it is connected to a load. In this case, the battery has a voltage of 8-13 V, and it is connected to a load resistor of 60 Ω.
The terminal voltage of a battery can be affected by various factors, including the internal resistance of the battery and the current flowing through the load. When a load is connected to the battery, the internal resistance of the battery can cause a voltage drop, reducing the terminal voltage.
In this scenario, the terminal voltage across the battery is given as 8-13 V. This range indicates that the terminal voltage can vary between 8 V and 13 V depending on the specific conditions and the load connected to the battery.
To determine the exact terminal voltage across the battery, more information is needed, such as the current flowing through the load or the internal resistance of the battery. Without this additional information, we can only conclude that the terminal voltage across the battery is within the range of 8-13 V.
In summary, the terminal voltage across the battery connected to a load resistor of 60 Ω is 8-13 V. This range indicates the potential voltage values that can be measured across the battery terminals, depending on the specific conditions and factors such as the internal resistance and the current flowing through the load.
Learn more about voltages:
brainly.com/question/14218449
#SPJ11
1027 kg) 16. A proton has a total energy of 2.5 x 100 J. How fast is it moving? (M = 1.67 x V (A) 0.90 16 m2 (R B) € 0,0 (B) 0.80 c (C) 0.70 € (D) 0.60 C (E) 0.40c
The speed of the proton is estimated to be [tex]3.00 * 10^8 m/s[/tex] the speed of light
Option B is correct
How do we calculate?The equation is :
E = γmc²
where E = total energy,
γ = Lorentz factor
m = rest mass of the proton,
and c = speed of light.
Total energy (E) =[tex]2.5 * 10^8 J[/tex]
Rest mass of the proton (m) = [tex]1.67 * 10^-^2^7 kg[/tex]
Speed of light (c) = [tex]3.00 * 10^8 m/s[/tex]
γ = E / (mc²)
γ = (2.5 x 10^8 J) / ((1.67 x 10^-27 kg) x (3.00 x 10^8 m/s)²)
γ = 4.45 x 10^8
β = √(1 - (1 / γ²))
β = √(1 - (1 / (4.45 x 10^8)²))
β ≈ 0.99999999999999999999999999438279
The speed of the proton is:
v = βc
v = (0.99999999999999999999999999438279) x ([tex]3.00 * 10^8 m/s[/tex])
v = 2.99999999999999999999999988274837 x [tex]10^8 m/s[/tex]
Learn more about Lorentz factor at:
https://brainly.com/question/24568887
#SPJ4
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) De
The force exerted by the mover must balance the forces of gravity and friction.
The work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
The piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
(a) To determine the force exerted by the mover, we need to consider the forces acting on the piano. These forces include the force of gravity, the normal force, the force exerted by the mover, and the frictional force. By analyzing the forces, we can find the force exerted by the mover parallel to the incline.
The force exerted by the mover must balance the forces of gravity and friction, as well as provide the necessary force to push the piano up the incline at a constant speed.
(b) The work done by the mover is calculated using the formula
W = F * d, where
W is the work done,
F is the force exerted by the mover
d is the distance moved.
In this case, the work done by the mover would be the force exerted by the mover multiplied by the distance the piano is pushed up the incline.
(c) The work done by the force of gravity can be calculated as the product of the force of gravity and the distance moved vertically. Since the piano is being pushed at a constant speed and there is no change in vertical position, the work done by the force of gravity is zero.
By considering the forces, work formulas, and the given values, we can determine the force exerted by the mover, the work done by the mover, and the work done by the force of gravity in pushing the piano up the incline.
Complete Question-
A 380 kg piano is pushed at constant speed a distance of 3.9 m up a 27° incline by a mover who is pushing parallel to the incline. The coefficient of friction between the piano & ramp is 0.45. (a) Determine the force exerted by the man (include an FBD for the piano): (b) Determine the work done by the man: (c) Determine the work done by the force of gravity
To know more about gravity , click here-
brainly.com/question/31321801
#SPJ11
A binocular consists of two lenses. The closest to the eye (eyepiece) is a diverging lens that is at a distance of 10 cm (when you want to see a distant object) from the other lens (objective), which is converging (focal length 15 cm). Find the focal length of the lens of the eye. Show all calculations
The question wants us to find the focal length of the eye lens. The diverging lens (eyepiece) is at a distance of 10 cm from the other lens (objective), which is converging (focal length 15 cm).
Let's calculate the focal length of the objective lens using the lens formula:1/f = 1/v - 1/uHere,u = -10 cmv = ∞ (as we can assume that the final image formed by the lens is at infinity)1/15 = 1/∞ + 1/-10=> 1/15 + 1/10 = 1/-f=> f = 30 cmNow, we know the focal length of the objective lens.
Let's calculate the focal length of the eyepiece lens. We know that the eyepiece is a diverging lens. Therefore, the focal length of the eyepiece lens is negative.Let the focal length of the eyepiece lens be f'.Using the lens formula,1/f' = 1/v - 1/uWe know that the final image is formed at infinity.
To know more about focal length visit:
https://brainly.com/question/31018369
#SPJ11
Question 16 An element, X has an atomic number 45 and a atomic mass of 133.559 u. This element is unstable and decays by decay, with a half life of 68d. The beta particle is emitted with a kinetic energy of 11.71 MeV. Initially there are 9.41×10¹² atoms present in a sample. Determine the activity of the sample after 107 days (in μCi). 1 pts
The activity of the sample after 107 days is 0.2777 μCi.
Atomic number of an element, X = 45
Atomic mass of an element, X = 133.559 u
Half-life = 68 d
Initial number of atoms in the sample = 9.41 x 10¹²
Beta particle emitted with kinetic energy = 11.71 MeV
To determine the activity of the sample after 107 days (in μCi), we use the formula given below:
Activity = λN
Where,
λ is the decay constant
N is the number of radioactive nuclei.
We know that the decay constant (λ) of an element is related to the half-life (t1/2) of an element as follows:
λ = 0.693/t1/2
Hence, the decay constant (λ) of the element can be calculated as follows:
λ = 0.693/68 = 0.01019 per day
Thus, the activity of the sample can be calculated using the formula as shown below:
Activity = λN = (0.01019 per day) x (9.41 x 10¹² atoms) = 9.604 x 10¹⁰ decays per day
Now, the activity is calculated for one day. To find the activity for 107 days, we multiply it by 107.
Activity after 107 days = 9.604 x 10¹⁰ decays/day x 107 days = 1.0275 x 10¹³ decays
Thus, the activity of the sample after 107 days is 1.0275 x 10¹³ decays.
The activity is measured in Becquerel (Bq) and microcurie (μCi) units.
1 Bq = 27 nCi (nano Curies)
1 μCi = 37 MBq
Hence, the activity of the sample after 107 days (in μCi) is calculated as shown below:
Activity in μCi = 1.0275 x 10¹³ decays x (1 Bq/decays) x (27 nCi/1 Bq) x (1 μCi/10⁶ nCi) = 0.2777 μCi
Therefore, the activity of the sample after 107 days is 0.2777 μCi (rounded to four significant figures).
To learn more about sample, refer below:
https://brainly.com/question/32907665
#SPJ11
In the partial wave analysis of low-energy scattering, we often find that S-wave scattering phase shift is all we need. Why do the higher partial waves tend not to contribute to scattering at this limit?
In partial wave analysis, the S-wave scattering phase shift is all we need to analyze low-energy scattering. At low energies, the wavelength is large, which makes the effect of higher partial waves to be minimal.
In partial wave analysis, the S-wave scattering phase shift is all we need to analyze low-energy scattering. The reason why the higher partial waves tend not to contribute to scattering at this limit is due to the following reasons:
The partial wave expansion of a scattering wavefunction involves the summation of different angular momentum components. In scattering problems, the energy is proportional to the inverse square of the wavelength of the incoming particles.
Hence, at low energies, the wavelength is large, which makes the effect of higher partial waves to be minimal. Moreover, when the incident particle is scattered through small angles, the dominant contribution to the cross-section comes from the S-wave. This is because the higher partial waves are increasingly suppressed by the centrifugal barrier, which is proportional to the square of the distance from the nucleus.
In summary, the contribution of higher partial waves tends to be negligible in the analysis of low-energy scattering. In such cases, we can get an accurate description of the scattering process by just considering the S-wave phase shift. This reduces the complexity of the analysis and simplifies the interpretation of the results.
This phase shift contains all the relevant information about the interaction potential and the scattering properties. The phase shift can be obtained by solving the Schrödinger equation for the potential and extracting the S-matrix element. The S-matrix element relates the incident and scattered waves and encodes all the scattering information. A simple way to extract the phase shift is to analyze the behavior of the wavefunction as it approaches the interaction region.
Learn more About S-wave from the given link
https://brainly.com/question/30540515
#SPJ11
12. (6 pts) In the picture below, rank particles A,B and C, which are moving in the directions shown by the arrows through a magnetic field pointing out of the page, in the order of increasing speed. Which particles are positive? Which are negative?
The particles moving in the direction opposite to the arrows (against the increasing speed) are positive, while the particles moving in the direction of the arrows (with the increasing speed) are negative.
In order to determine the polarity of the charged particles, we need to consider the interaction between the magnetic field and the motion of the particles. According to the right-hand rule for charged particles, when a charged particle moves in a magnetic field, the direction of the force experienced by the particle is perpendicular to both the velocity of the particle and the magnetic field direction.
Given that the magnetic field is pointing out of the page, we can apply the right-hand rule. When the velocity vector is in the direction of the arrow and the force is out of the page, the charge on the particles must be negative. Conversely, when the velocity vector is in the opposite direction to the arrow and the force is into the page, the charge on the particles must be positive.
Therefore, the particles moving in the direction opposite to the arrows (against the increasing speed) are positive, while the particles moving in the direction of the arrows (with the increasing speed) are negative.
To know more about right-hand rule, here
brainly.com/question/30641867
#SPJ4
--The complete Question is, A beam of charged particles is moving in the directions shown by the arrows through a magnetic field pointing out of the page, in the order of increasing speed. Which particles are positive? Which are negative? --
A ball of mass m= 75.0 grams is dropped from a height of 2.00 m. The ball stays in contact with the ground 25.0 ms. How high did it bounce back up if the ground exerts a force of 30.0 N on it
The ball of mass m=75.0 g is dropped from a height of 2.00 m. It bounces back with a height of 0.5 m.
To determine the height to which the ball bounced back up, use the conservation of energy principle. The total mechanical energy of a system remains constant if no non-conservative forces do any work on the system. The kinetic energy and the potential energy of the ball at the top and bottom of the bounce need to be calculated. The force of the ground is considered a non-conservative force, and it does work on the ball during the impact. Therefore, its work is equal to the loss of mechanical energy of the ball.
The potential energy of the ball before the impact is equal to its kinetic energy after the impact because the ball comes to a halt at the top of its trajectory.
Hence, mgh = 1/2mv²v = sqrt(2gh) v = sqrt(2 x 9.81 m/s² x 2.00 m) v = 6.26 m/s.
The force applied by the ground on the ball is given by the equation
F = m x a where F = 30 N and m = 75.0 g = 0.075 kg.
So, a = F/m a = 30 N / 0.075 kg a = 400 m/s²
Finally, h = v²/2a h = (6.26 m/s)² / (2 x 400 m/s²) h = 0.5 m.
Thus, the ball bounced back to a height of 0.5 meters.
Learn more about potential energy:
https://brainly.com/question/9349250
#SPJ11