Answer:
The peak output voltage of this generator is 314.2 V.
Explanation:
Given;
the number of turns of the coil, N = 1000 turns
area of the coil, A = 0.001 m²
angular frequency of the coil, f = 100 cycles/seconds
magnitude of the magnetic field, B = 0.5 T
The peak output voltage of this generator is given by;
E = NBAω
Where;
ω is the angular velocity = 2πf
E = NBA(2πf)
E = 1000 x 0.5 x 0.001(2 x π x 100)
E = 314.2 V
Therefore, the peak output voltage of this generator is 314.2 V.
We observe that a moving charged particle experiences no magnetic force. From this we can definitely conclude that:_______
a. no magnetic field exists in that region of space.
b. the particle must be moving parallel to the magnetic field.
c. the particle is moving at right angles to the magnetic field.
d. either no magnetic field exists or the particle is moving parallel to the magnetic field.
e. either no magnetic field exists or the particle is moving perpendicular to the magnetic field.
Answer:
b. the particle must be moving parallel to the magnetic field.
Explanation:
The magnetic force on a moving charged particle is given by;
F = qvBsinθ
where;
q is the charge of the particle
v is the velocity of the particle
B is the magnetic field
θ is the angle between the magnetic field and velocity of the moving particle.
When is the charge is stationary the magnetic force on the charge is zero.
Also when the charge is moving parallel to the magnetic field, the magnetic force is zero.
Therefore, when a moving charged particle experiences no magnetic force, we can definitely conclude that the particle must be moving parallel to the magnetic field.
b. the particle must be moving parallel to the magnetic field.
Did the kinetic frictional coefficient (for the wood/aluminum and felt/aluminum cases) vary with area of contact
Answer:
Explanation:
Friction is defined as a force which acts at the surface of separation between two objects in contact and tends to oppose motion of one over the other.
While kinetic friction is the force that must be overcome so that a body can move with uniform speed over another.
Hence let consider one of the laws of friction which states that: '' Frictional force is independent of the area of the surfaces in contact.''
The value did not vary with area. This is because when calculating the kinetic fiction, the total contact area is not relevant and only the total weight of the system as well of as the block is put into consideration.
A skull believed to belong to an ancient human being has a carbon-14 decay rate of 5.4 disintegrations per minute per gram of carbon (5.4 dis/min*gC). If living organisms have a decay rate of 15.3 dis/min*gC, how old is this skull
Answer:
9.43*10^3 year
Explanation:
For this question, we ought to remember, or know that the half life of carbon 14 is 5730, and that would be vital in completing the calculation
To start with, we use the formula
t(half) = In 2/k,
if we make k the subject of formula, we have
k = in 2/t(half), now we substitute for the values
k = in 2 / 5730
k = 1.21*10^-4 yr^-1
In(A/A•) = -kt, on rearranging, we find out that
t = -1/k * In(A/A•)
The next step is to substitite the values for each into the equation, giving us
t = -1/1.21*10^-4 * In(5.4/15.3)
t = -1/1.21*10^-4 * -1.1041
t = 0.943*10^4 year
PLEASE HELP FAST The object distance for a convex lens is 15.0 cm, and the image distance is 5.0 cm. The height of the object is 9.0 cm. What is the height of the image?
Answer:
The image height is 3.0 cm
Explanation:
Given;
object distance, [tex]d_o[/tex] = 15.0 cm
image distance, [tex]d_i[/tex] = 5.0 cm
height of the object, [tex]h_o[/tex] = 9.0 cm
height of the image, [tex]h_i[/tex] = ?
Apply lens equation;
[tex]\frac{h_i}{h_o} = -\frac{d_i}{d_o}\\\\ h_i = h_o(-\frac{d_i}{d_o})\\\\h_i = -9(\frac{5}{15} )\\\\h_i = -3 \ cm[/tex]
Therefore, the image height is 3.0 cm. The negative values for image height indicate that the image is an inverted image.
A small omnidirectional stereo speaker produces waves in all directions that have an intensity of 8.00 at a distance of 4.00 from the speaker.
At what rate does this speaker produce energy?
What is the intensity of this sound 9.50 from the speaker?
What is the total amount of energy received each second by the walls (including windows and doors) of the room in which this speaker is located?
Answer:
A. We have that radius r = 4.00m intensity I = 8.00 W/m^
total power = power/ Area ( 4πr2)= 8.00 w/m^2( 4π ( 4.00 m)2=1607.68 W
b) I = total power/ 4πr2= 8.00 W/m2 ( 4.00 m/ 9.5 m)2= 1.418 W/m2
c) E = total power x time= 1607 . 68 W x 1s= 1607.68 J
Under normal circumstances: _________
a. Fetal Hb binds to oxygen more tightly than Mb binds.
b. Fetal Hb binds oxygen more tightly in the absence of 2,3-BPG.
c. Fetal Hb does not bind to oxygen.
d. Adult Hb has the lowest affinity for oxygen of the 3.
e. More than one of these statements is correct.
Answer:
Fetal Hb binds oxygen more tightly than adult Hb (not option a)
The cylinder is displaced 0.17 m downward from its equilibrium position and is released at time t = 0. Determine the displacement y and the velocity v when t = 3.1 s. The displacement and velocity are positive if downward, negative if upward. What is the magnitude of the maximum acceleration?
Complete Question
The image of this question is shown on the first uploaded image
Answer:
a
[tex]d =0.161 \ m[/tex]
b
[tex]v = - 0.054 \ m/s[/tex]
c
[tex]a = 6.12 \ m/s^2[/tex]
Explanation:
From the question we are told that
The maximum displacement is A = 0.17 m
The time considered is [tex]t = 3.1 \ s[/tex]
The spring constant is [tex]k = 137 \ N \cdot m[/tex]
The mass is [tex]m = 3.8 \ kg[/tex]
Generally given that the motion which the cylinder is undergoing is a simple harmonic motion , then the displacement is mathematically represented as
[tex]d = A cos (w t )[/tex]
Where [tex]w[/tex] is the angular frequency which is mathematically evaluated as
[tex]w = \sqrt{\frac{k}{m} }[/tex]
substituting values
[tex]w = \sqrt{\frac{137}{ 3.8} }[/tex]
[tex]w =6[/tex]
So the displacement is at t
[tex]d = 0.17 cos (6 * 3.1 )[/tex]
[tex]d =0.161 \ m[/tex]
Generally the velocity of a SHM(simple harmonic motion) is mathematically represented as
[tex]v = - Asin (wt)[/tex]
substituting values
[tex]v = - 0.17 sin ( 6 * 3.1 )[/tex]
[tex]v = - 0.054 \ m/s[/tex]
Generally the maximum acceleration is mathematically represented as
[tex]a = w^2 * A[/tex]
substituting values
[tex]a_{max} = 6^2 * (0.17)[/tex]
substituting values
[tex]a = 6^2 * (0.17)[/tex]
[tex]a = 6.12 \ m/s^2[/tex]
Five wheels are connected as shown in the figure. Find the velocity of the block “Q”, if it is known that: RA= 5 [m], RB= 10 [m], RD= 6 [m], RE=12 [m].
Answer:
-5 m/s
Explanation:
The linear velocity of B is equal and opposite the linear velocity of E.
vB = -vE
vB = -ωE rE
10 m/s = -ωE (12 m)
ωE = -0.833 rad/s
The angular velocity of E is the same as the angular velocity of D.
ωE = ωD
ωD = -0.833 rad/s
The linear velocity of Q is the same as the linear velocity of D.
vQ = vD
vQ = ωD rD
vQ = (-0.833 rad/s) (6 m)
vQ = -5 m/s
please help !!!!! please note that two images are there................ i am urgently needs this question
Answer:
can you tell me about this property
the rate of cooling determines ....... and ......
Answer:
freezing point and melting point
if C is The vector sum of A and B C = A + B What must be true about The directions and magnitudes of A and B if C=A+B? What must be tre about the directions and magnitudes of A and B if C=0?
Check attached photo
Check attached photo
A block weighing 400 kg rest on a horizontal surface and supports on top of it another block of weight 100 kg placed on the top of it as shown. The block W2 is attached to a vertical wall by a string 6 m long. Ifthe coefficient of friction between all surfaces is 0.25 and the system is in equilibrium find the magnitude of the horizontal force P applied to the lower block.
The horizontal force applied to the lower block is approximately 1,420.85 Newtons
The known parameters are;
The mass of the block, m₁ = 400 kg, weight, W₁ = 3,924 N
The mass of the block resting on the first block, m₂ = 100 kg, weight, W₂ = 981 N
The length of the string attached to the block, W₂, l = 6 m
The horizontal distance from the point of attachment of the second block to the block W₂, x = 5 m
The coefficient of friction between the surfaces, μ = 0.25
Let T represent the tension in the string
The upward force on W₂ due to the string = T × sin(θ)
The normal force of W₁ on W₂, N₂ = W₂ - T × sin(θ)
The tension in the string, T = N₂ × μ × cos(θ)
∴ T = (W₂ - T × sin(θ)) × μ × cos(θ)
sin(θ) = √(6² - 5²)/6
cos(θ) = 5/6
∴ T = (981 - T × √(6² - 5²)/6) × 0.25 × 5/6
Solving, we get;
T ≈ 183.27 N
The normal reaction on W₂, N₂ = T/(μ × cos(θ))
∴ N₂ = 183.27/(0.25 × 5/6) = 879.7
N₂ ≈ 879.7 N
The friction force, [tex]F_{f2}[/tex] = N₂ × μ
∴ [tex]F_{f2}[/tex] = 879.7 N × 0.25 = 219.925 N
The total normal reaction on the ground, [tex]\mathbf{N_T}[/tex] = W₁ + N₂
[tex]N_T[/tex] = 3,924 N + 879.7 N = 4,803.7 N
The friction force, on the ground [tex]\mathbf{F_T}[/tex] = [tex]\mathbf{N_T}[/tex] × μ
∴ [tex]F_T[/tex] = 4,803.7 N × 0.25 = 1,200.925 N
The horizontal force applied to the lower block, P = [tex]\mathbf{F_T}[/tex] + [tex]\mathbf{F_{f2}}[/tex]
Therefore;
P = 1,200.925 N + 219.925 N = 1,420.85 N
The horizontal force applied to the lower block, P ≈ 1,420.85 N
Select the correct answer.
What is abstraction?
OA. the concept that software architecture can be separated into modules and that each module can be examined independently
OB. the process of containing information within a module, preventing any crossover or access to Irrelevant information
OC. the process of splitting a program both horizontally and vertically
OD. the process of cutting down irrelevant information so only the information that is useful for a particular purpose remains
Reset
Next
2021 Edmentum. All rights reserved.
O
Sign out
4:
Answer:
OD. The process of cutting down irrelevant information so only the information that is useful for particular purpose remains
Abstraction is the process of cutting down irrelevant information so only the information that is useful for a particular purpose remains.
What is abstraction?Abstraction is the practice of removing anything from a set of core features by eliminating or deleting attributes.
One of the three core ideas of object-oriented programming is abstraction order to decrease complexity and maximize efficiency, a programmer uses abstraction to conceal all but the important facts about an object.
Abstraction is the process of cutting down irrelevant information so only the information that is useful for a particular purpose remains.
Hence option D is correct.
To learn more about the abstraction refer to the link;
https://brainly.com/question/13072603
A rock has mass 1.80 kg. When the rock is suspended from the lower end of a string and totally immersed in water, the tension in the string is 10.8 N . What is the smallest density of a liquid in which the rock will float?
Answer:
The density is [tex]\rho_z = 2544 \ kg /m^3[/tex]
Explanation:
From the question we are told that
The mass of the rock is [tex]m_r = 1.80 \ kg[/tex]
The tension on the string is [tex]T = 10.8 \ N[/tex]
Generally the weight of the rock is
[tex]W = m * g[/tex]
=> [tex]W = 1.80 * 9.8[/tex]
=> [tex]W = 17.64 \ N[/tex]
Now the upward force(buoyant force) acting on the rock is mathematically evaluated as
[tex]F_f = W - T[/tex]
substituting values
[tex]F_f = 17.64 - 10.8[/tex]
[tex]F_f = 6.84 \ N[/tex]
This buoyant force is mathematically represented as
[tex]F_f = \rho * g * V[/tex]
Here [tex]\rho[/tex] is the density of water and it value is [tex]\rho = 1000\ kg/m^3[/tex]
So
[tex]V = \frac{F_f}{ \rho * g }[/tex]
[tex]V = \frac{6.84}{ 1000 * 9.8 }[/tex]
[tex]V = 0.000698 \ m^3[/tex]
Now for this rock to flow the upward force (buoyant force) must be equal to the length
[tex]F_f = W[/tex]
[tex]\rho_z * g * V = W[/tex]
Here z is smallest density of a liquid in which the rock will float
=> [tex]\rho_z = \frac{W}{ g * V}[/tex]
=> [tex]\rho_z = \frac{17.64}{ 0.000698 * 9.8}[/tex]
=> [tex]\rho_z = 2544 \ kg /m^3[/tex]
Air is compressed polytropically from 150 kPa, 5 meter cube to 800 kPa. The polytropic exponent for the process is 1.28. Determine the work per unit mass of air required for the process in kilojoules
a) 1184
b) -1184
c) 678
d) -678
Answer:
wegkwe fhkrbhefdb
Explanation:B
Helium-neon laser light (λ = 6.33 × 10−7 m) is sent through a 0.30 mm-wide single slit. What is the width of the central maximum on a screen 1.0 m from the slit?
Answer:
The width is [tex]w_c = 0.00422 \ m[/tex]
Explanation:
From the question we are told that
The wavelength is [tex]\lambda = 6.33*10^{-7} \ m[/tex]
The width of the slit is [tex]d = 0.3\ mm = 0.3 *10^{-3} \ m[/tex]
The distance of the screen is [tex]D = 1.0 \ m[/tex]
Generally the central maximum is mathematically represented as
[tex]w_c = 2 * y[/tex]
Here y is the width of the first order maxima which is mathematically represented as
[tex]y = \frac{\lambda * D}{d}[/tex]
substituting values
[tex]y = \frac{6.33*10^{-7} * 1.0}{ 0.30}[/tex]
[tex]y = 0.00211 \ m[/tex]
So
[tex]w_c = 2 *0.00211[/tex]
[tex]w_c = 0.00422 \ m[/tex]
PLEASEEEEEEEE HELP WILL MARK BRAINLYIST
5. Theories are models that explain but laws __________.
Answer:
Theories are models that explain but laws just describes an action under certain circumstances
Explanation:
Evolution is a law that does not explain how and why
But evolution by natural selection is a theory because it explain how it happens
A 1.8-mole sample of an ideal gas is allowed to expand at a constant temperature of 250 K. The initial volume is 34 L and the final volume is 80 L. How much work does the gas perform on its container? Let the ideal-gas constant R = 8.314 J/(mol • K).
Answer:
3201.304 J
Explanation:
Use ideal gas equation to initial stage:
PV=nRT
P * 0.034 = 1.8 * 8.314 * 250
P = 110038.2353 Pa
Use ideal gas equation to final stage:
PV=nRT
P * 0.08 = 1.8 * 8.314 * 250
P = 46766.25 Pa
Process is isothermal (constant temperature )
Therefore,
Work= C ln (V2/V1)
(P1V1=P2V2=C)
(Above equation is taken by integration of P.dv)
Work = P1V1 ln (V2/V1) = P2V2 ln (V2/V1)
By substituting above data to the equation:
Work = (110038.2353 * 0.034) * ln (0.08/0.034)
Work = 3201.304 J
A massage technique that consists of applying pressure to specific points of the face and body to release muscle tension, stimulate and restore balance (chi) is known as
Answer:Acupressure
.
.
..
But why post this question in Physics
A 180-km-long high-voltage transmission line 2.00 cm in diameter carries a steady current of 1,050 A. If the conductor is copper with a free charge density of 8.50 1028 electrons per cubic meter, how many years does it take one electron to travel the full length of the cable
Answer:
27yrs
Explanation:
h= difference in height between the initial position and the bottom position
We are told that the rope is L = 2.30 m long and inclined at 45.0° from the vertical
h=L-Lcos(x)= L(1-cosx)=2.30(1-cos45)
=0.674m
Potential Energy = 28× 9.8×0.674
=184.9J
B)we can see that at the bottom of the motion, all the initial potential energy of the child has been converted into kinetic energy:
E= 0.5mv^2
What is Matter? write its types
According to definition of general chemistry matter is any substance which has atleast a mass and occupies a volume.
Matter is of three types
SolidLiquidGasAir flows through a converging-diverging nozzle/diffuser. A normal shock stands in the diverging section of the nozzle. Assuming isentropic flow, air as an ideal gas, and constant specific heats determine the state at several locations in the system. Solve using equations rather than with the tables.
Answer:
HELLO your question has some missing parts below are the missing parts
note: The specific heat ratio and gas constant for air are given as k=1.4 and R=0.287 kJ/kg-K respectively.
--Given Values--
Inlet Temperature: T1 (K) = 325
Inlet pressure: P1 (kPa) = 560
Inlet Velocity: V1 (m/s) = 97
Throat Area: A (cm^2) = 5.3
Pressure upstream of (before) shock: Px (kPa) = 207.2
Mach number at exit: M = 0.1
Answer: A) match number at inlet = 0.2683
B) stagnation temperature at inlet = 329.68 k
C) stagnation pressure = 588.73 kPa
D) ) Throat temperature = 274.73 k
Explanation:
Determining states at several locations in the system
A) match number at inlet
= V1 / C1 = 97/ 261.427 = 0.2683
C1 = sound velocity at inlet = [tex]\sqrt{K*R*T}[/tex] = [tex]\sqrt{1.4 *0.287*10^3}[/tex] = 361.427 m/s
v1 = inlet velocity = 97
B) stagnation temperature at inlet
= T1 + [tex]\frac{V1 ^2}{2Cp}[/tex] = 325 + [tex]\frac{97^2}{2 * 1.005*10^{-3} }[/tex]
stagnation temperature = 329.68 k
C) stagnation pressure
= [tex]p1 ( 1 + 0.2Ma^2 )^{3.5}[/tex]
Ma = match number at inlet = 0.2683
p1 = inlet pressure = 560
hence stagnation pressure = 588.73 kPa
D) Throat temperature
= [tex]\frac{Th}{T} = \frac{2}{k+1}[/tex]
Th = throat temperature
T = stagnation temp at inlet = 329.68 k
k = 1.4
make Th subject of the relation
Th = 329.68 * (2 / 2.4 ) = 274.73 k
can you guys pls also solve for average speed.
Answer:
d_t = 3.05km
v_a = 4.3km/h
Explanation:
42mins*(2/3) = 28mins
42mins-28mins = 14mins
d = v*t
d_1 = (4km/h)*(1h/60mins)*(28mins)
d_1 = 1.87km
d_2 = (5km/h)*(1h/60mins)*(14mins)
d_2 = 1.17km
d_t = d_1+d_2
d_t = 1.87km+1.17km
d_t = 3.05km
v_a = (v_1+v_2)/2
v_a = [(2*4km/h)+5km/h)]/3
v_a = 4.3km/h
A viewing screen is separated from a double slit by 5.20 m. The distance between the two slits is 0.0300 mm. Monochromatic light is directed toward the double slit and forms an interference pattern on the screen. The first dark fringe is 3.70 cm from the center line on the screen.
Required:
a. Determine the wavelength of light.
b. Calculate the distance between the adjacent bright fringes.
Answer:
The wavelength of this light is approximately [tex]427\; \rm nm[/tex] ([tex]4.27\times 10^{-7}\; \rm m[/tex].)The distance between the first and central maxima is approximately [tex]7.40\; \rm cm[/tex] (about twice the distance between the first dark fringe and the central maximum.)Explanation:
WavelengthConvert all lengths to meters:
Separation of the two slits: [tex]0.0300\; \rm mm = 3.00\times 10^{-5}\; \rm m[/tex].Distance between the first dark fringe and the center of the screen: [tex]3.70\; \rm cm = 3.70\times 10^{-2}\; \rm m[/tex].Refer to the diagram attached (not to scale.) Assuming that the screen is parallel to the line joining the two slits. The following two angles are alternate interior angles and should be equal to each other:
The angle between the filter and the beam of light from the lower slit, andThe angle between the screen and that same beam of light.These two angles are marked with two grey sectors on the attached diagram. Let the value of these two angles be [tex]\theta[/tex].
The path difference between the two beams is approximately equal to the length of the segment highlighted in green. In order to produce the first dark fringe from the center of the screen (the first minimum,) the length of that segment should be [tex]\lambda / 2[/tex] (one-half the wavelength of the light.)
Therefore:
[tex]\displaystyle \cos \theta \approx \frac{\text{Path difference}}{\text{Slit separation}} = \frac{\lambda / 2}{3.00\times 10^{-5}\; \rm m}[/tex].
On the other hand:
[tex]\begin{aligned} \cot \theta &\approx \frac{\text{Distance between central peak and first minimum}}{\text{Distance between the screen and the slits}} \\ &= \frac{3.70\times 10^{-2}\; \rm m}{5.20\; \rm m} \approx 0.00711538\end{aligned}[/tex].
Because the cotangent of [tex]\theta[/tex] is very close to zero,
[tex]\cos \theta \approx \cot \theta \approx 0.00711538[/tex].
[tex]\displaystyle \frac{\lambda /2}{3.00\times 10^{-5}\; \rm m} \approx \cos\theta\approx 0.00711538[/tex].
[tex]\begin{aligned}\lambda &\approx 2\times 0.00711538 \times \left(3.00\times 10^{-5}\; \rm m\right) \\ &\approx 4.26 \times 10^{-7}\; \rm m = 426\; \rm nm\end{aligned}[/tex].
Distance between two adjacent maximaIf the path difference is increased by one wavelength, then the intersection of the two beams would move from one bright fringe to the next one.
The path difference required for the central maximum is [tex]0[/tex].The path difference required for the first maximum is [tex]\lambda[/tex].The path difference required for the second maximum is [tex]2\,\lambda[/tex].On the other hand, if the distance between the maximum and the center of the screen is much smaller than the distance between the screen and the filter, then:
[tex]\begin{aligned}&\frac{\text{Distance between image and center of screen}}{\text{Distance between the screen and the slits}} \\ &\approx \cot \theta \\ &\approx \cos \theta \\ &\approx \frac{\text{Path difference}}{\text{Slit separation}}\end{aligned}[/tex].
Under that assumption, the distance between the maximum and the center of the screen is approximately proportional to the path difference. The distance between the image (the first minimum) and the center of the screen is [tex]3.70\; \rm cm[/tex] when the path difference is [tex]\lambda / 2[/tex]. The path difference required for the first maximum is twice as much as that. Therefore, the distance between the first maximum and the center of the screen would be twice the difference between the first minimum and the center of the screen: [tex]2 \times 3.70\; \rm cm = 7.40\; \rm cm[/tex].
when 999mm is added to 100m ______ is the result
Answer:
what, 100.999m
Explanation:
convert 999 mm into meters, which is 0.999m and add that to a 100 m and that will make the total 100.999 m
The result of the addition of the two values is equal to 100.999 meters.
Given the following data:
Value 1 = 999 millimetersValue 2 = 100 metersTo determine the result of the addition of the two values:
First of all, we would convert the value in millimeter (mm) to meter (m) as follows:
Conversion:
1 millimeter = 0.001 meter
999 millimeter = X meter
Cross-multiplying, we have:
[tex]X = 0.001 \times 999[/tex]
X = 0.999 meter.
For the result:
[tex]Result = 0.999 +100[/tex]
Result = 100.999 meters.
Read more on measurements here: https://brainly.com/question/24842282
A plastic box with objects has a mass of 4 kg and is on a shelf at a height of 2.4 m. What will it's potential gravitational energy?
Answer:
potential energy=mgh
4×9.8×2.4
Explanation:
may be hope this will help you
Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/2 its former radius. a. What are the pressure and velocity of the water after the contraction
Answer:
Explanation:
Using the Continuity equation
v X A = v' xA'
so if A is 1/2of A' then A velocity must be 2 times the A'
after-contraction v = 2 x 5.0m/s = 10m/s
Using the Bernoulli equation
p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂
, the "h" terms cancel
3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²
p₂ = 342500pa
One solenoid is centered inside another. The outer one has a length of 54.0 cm and contains 6750 coils, while the coaxial inner solenoid is 4.00 cm long and 0.170 cm in diameter and contains 21.0 coils. The current in the outer solenoid is changing at 35.0 A/s .What is the mutual inductance of the solenoids?Find the emf induced in the inner solenoid.
Answer:
M₁₂ = 1.01 10⁻⁴ H , Fem = 3.54 10⁻³ V
Explanation:
The mutual inductance between two systems is
M₁₂ = N₂ Ф₁₂ / I₁
where N₂ is the number of turns of the inner solenoid N₂ = 21.0, i₁ the current that flows through the outer solenoid I₁ = 35.0 A / s and fi is the flux of the field of coil1 that passes through coil 2
the magnetic field of the coil1 is
B = μ₀ n I₁ = μ₀ N₁/l I₁
the flow is
Φ = B A₂
the area of the second coil is
A₂ = π d₂ / 4
Φ = μ₀ N₁ I₁ / L π d² / 4
we substitute in the first expression
M₁₂ = N₂ μ₀ N₁ / L π d² / 4
M₁₂ = μ₀ N₁ N₂ π d² / 4L
d = 0.170 cm = 0.00170 m
L = 4.00 cm = 0.00400 m
let's calculate
M₁₂ = 4π 10⁻⁷ 6750 21 π 0.0017²/ (4 0.004)
M₁₂ = π² 0.40966 10⁻⁷ / 0.004
M₁₂ = 1.01 10⁻⁴ H
The electromotive force is
Fem = - M dI₁ / dt
Fem = - 1.01 10⁻⁴ 35.0
Fem = 3.54 10⁻³ V
A hammer is used to hit a nail into a board. Which statement is correct about the forces at play between the nail and the hammer?
O The nail exerts a much smaller force on the hammer in the opposite direction
O The nail exerts a much smaller force on the hammer in the same direction.
The nail exerts an equal force on the hammer in the same direction.
O The nail exerts an equal force on the hammer in the opposite direction.
Answer:
reviewing the final statements, the correct one is the quarter
The nail exerts an equal force on the hammer in the opposite direction.
Explanation:
This is an action-reaction problem or Newton's third law, which states that forces in naturals occur in pairs.
This is the foregoing, the hammer exerts a force on the nail of magnitude F and it will direct downwards, if we call this action and the nail exerts a force on the hammer of equal magnitude but opposite direction bone directed upwards, each force is applied in one of the bodies.
The difference in result that each force is that the force between the nail exerts a very high pressure (relation between the force between the nail area), instead the area of the hammer is much greater, therefore the pressure is small.
When reviewing the final statements, the correct one is the quarter
The nail exerts an equal force on the hammer in the opposite direction.
Find the current through a person and identify the likely effect on her if she touches a 120 V AC source in the following circumstances. (Note that currents above 10 mA lead to involuntarily muscle contraction.)
(a) if she is standing on a rubber mat and offers a total resistance of 300kΩ
(b) if she is standing barefoot on wet grass and has a resistance of only 4000kΩ
Answer:
A) 0.4 mA
B) 0.03 mA
Explanation:
Given that
voltage source, V = 120 V
to solve this question, we would be using the very basic Ohms Law, that voltage is proportional to the current and the resistance passing through the circuit, if temperature is constant.
mathematically, Ohms Law, V = IR
V = Voltage
I = Current
R = Resistance
from question a, we were given 300kΩ, substituting this value of resistance in the equation, we have
120 = I * 300*10^3 Ω
making I the subject of the formula,
I = 120 / 300000
I = 0.0004 A
I = 0.4 mA
Question said, currents above 10 mA causes involuntary muscle contraction, this current is way below 10 mA, so nothing happens.
B, we have Resistance, R = 4000kΩ
Substituting like in part A, we have
120 = I * 4000*10^3 Ω
I = 120 / 4000000
I = 0.00003 A
I = 0.03 mA
This also means nothing happens, because 0.03 mA is very much lesser compared to in the 10 mA
The current through a person will be:
a) 0.4 mA
b) 0.03 mA
Given:
Voltage, V = 120 V
Ohm's Law:It states that the voltage or potential difference between two points is directly proportional to the current or electricity passing through the resistance, and directly proportional to the resistance of the circuit.
Ohms Law, V = I*R
where,
V = Voltage
I = Current
R = Resistance
a)
Given: Resistance= 300kΩ
[tex]120 = I * 300*10^3 ohm\\\\I = 120 / 300000\\\\I = 0.0004 A[/tex]
Thus, current will be, I = 0.4 mA
b)
Given: R = 4000kΩ
[tex]120 = I * 4000*10^3 ohm\\\\I = 120 / 4000000\\\\I = 0.00003 A[/tex]
Thus, current will be, I = 0.03 mA
From calculations, we observe that nothing happens, because 0.03 mA is very much lesser compared to in the 10 mA.
Find more information about Current here:
brainly.com/question/24858512