Answer:
a. Workdone = 44100 Joules
b. Power = 8820 Watts.
Explanation:
Given the following data:
Mass = 225kg
Distance = 20m
Time = 5 seconds
To find the workdone;
Workdone = force * distance
But force = mg
We know that acceleration due to gravity is equal to 9.8m/s²
Force = 225*9.8 = 2205N
Substituting the values into the equation, we have;
Workdone = 2205 * 20
Workdone = 44100 Joules
b. To find the power;
Power = workdone/time
Power = 44100/5
Power = 8820 Watts.
We assume the foam plate has a positive charge when rubbed with paper towels.
Lift the pan away from the charged plate using the styrofoam cup. Briefly touch the rim of the pan to neutralize it. Place the neutralized pan on the plate and observe the tape rise. When the pan is on the plate, the rim of the plate has a _____________. This means that the pan base is ________________ charged because the net charge on the pan is __________. You know that this must be the case because as you lift the pan with the cup away from the plate, the tape on the rim goes down.
Answer:
POSITIVE CHARGE, NEGATIVE CHARGE, ZERO
Explanation:
To solve this completion exercise, we must remember that charges of the same sign repel each other and in a metallic object (frying pan) the charge is mobile.
Let's analyze the situation when we touch the pan, the charges are neutralized, therefore when we bring the pan to the plate that has a positive charge, it attracts the mobile negative charges in the pan, until it is neutralized, therefore on the opposite side of the pan. pan (edge with a glued tape) is left with a positive charge; therefore the edge and the tape, which is very light, have positive charges and repel each other.
We must assume that the frying pan is insulated so that the net charge is zero, since the induction process.
Consequently the words to complete the sentence are
When the pan is on the plate, the edge of the plate has a _POSITIVE CHARGE_____.
This means that the base of the container is loaded NEGATIVE CHARGE_____ because the net charge of the container is ___ZERO_
1.A boy runs at a speed of 3.3 m/s straight off the end of a diving board that is 3 meters above the water
2.What is the horizontal distance the boy in # 1 travels while in the air ?
If a boy runs at a speed of 3.3 m/s straight off the end of a diving board that is 3 meters above the water, then the horizontal distance traveled by the boy would be 2.58 meters.
What are the three equations of motion?There are three equations of motion given by Newton,
v = u + at
S = ut + 1/2 × a × t²
v² - u² = 2 × a × s
As given in the problem if a boy runs at a speed of 3.3 m/s straight off the end of a diving board that is 3 meters above the water,
3 = ut + 1/2 × a × t²
3 = 0 + 0.5 × 9.8 × t²
t = 3 / 4.9
t = 0.7824
The horizontal distance traveled by the boy = 3.3 × 0.7824
= 2.58 meters
Thus, the horizontal distance traveled by the boy would be 2.58 meters.
To learn more about equations of motion here, refer to the link;
brainly.com/question/5955789
#SPJ2
A bowling ball and a small marble will fall downward to the surface of the Moon at the same rate because ____________.a. the force of gravity is the same for each object.
b. the force of gravity on an object in a vacuum is zero.
c. the ratio of the force of gravity exerted on an object to the object's mass is the same.
Answer:
The answer is C
Explanation:
If the diameter of a moose eye is 40 mm, what is the total refractive power of the anterior portion of the eye?
Answer:
-the ratio of the speed of light
in air to the speed of light in the substance.
-speed of light in air 300,000 km/sec, which decreases when it passes through a transparent substance.
-e.g.. speed of light in substance = 200,000 km/sec, R.I. = 300,000/200,000 = 1.5
Explanation:
A spring is stretched 5 mm by a force of 125 N. How much will the spring stretch
when 250 N force is applied?
Answer:
10 mm
Explanation:
We'll begin by calculating the spring constant of the spring. This can be obtained as follow:
Extention (e) = 5 mm
Force (F) = 125 N
Spring constant (K) =?
F = Ke
125 = K × 5
Divide both side by 5
K = 125 / 5
K = 25 N/mm
Finally, we shall determine how much the spring will stretch when a 250 N force is applied. This can be obtained as follow:
Force (F) = 250 N
Spring constant (K) = 25 N/mm
Extention (e) =?
F = Ke
250 = 25 × e
Divide both side by 25
e = 250 / 25
e = 10 mm
Thus, the spring will stretch 10 mm when a 250 N force is applied.
A liquid fueled rocket is red on a test stand. The rocket nozzle has an exit diameter of 30 cm and the combustion gases leave the nozzle at a velocity of 3800 m/s and a pressure of 100 kPa, which is the same as the ambient pressure. The temperature of the gases in the combustion area is 2400 C. Find (a) the temperature of the gases at the nozzle exit plane, (b) the pressure in the combustion area, and (c) the thrust developed. Assume that the gases have a speci c heat ratio of 1.3, and a molar mass of 9. Assume that the ow in the nozzle is isentropic.
Answer:
1. Temperature= 869.35 K
2. Pressure of combustion = 12994.043 kpa
3. Thrust = 127x10⁶N
Explanation:
this problem has been fully explained in the attachment. please use it to get a clearer explanation of the answer.
1.
The temperature = (273+2400k) - (3800)²/2(4003)
= 2673 - 14440000/8006
= 2673 - 1803.65
= 869.35 K
Approximately 869.4K
2. We first get mach number
= 3800/√1.3(923.8)(869.35)
= 3800/1021.78
= 3.719
Pressure = 100kpa[1+2.07464415]^1.3/0.3
= 12995.043kpa
C. Thrust
Pi/4(3800)²(0.3)²(100x10³)/(923.8)(869.4)
= 12678.621
= 126.781 kN
Thrust is approximately 127kN = 127x10⁶N
List down the types of centripetal force?
Answer: Just a few examples are the tension in the rope on a tether ball, the force of Earth's gravity on the Moon, friction between roller skates and a rink floor, a banked roadway's force on a car, and forces on the tube of a spinning centrifuge. Any net force causing uniform circular motion is called a centripetal force.
Answer:
roller skates and a rink floor, a banked roadway's force on a car, and forces on the tube of a spinning centrifuge
Explanation:
QUCIK!! SOMEONE PLEASE HELP! I’LL MARK BRAINLIEST!!
Answer:
A. v = √2gh
B. No! The final velocity does not depend on the mass of the car.
C. Yes! the final velocity depends on the steepness of the hill
D. 3.28 m/s
Explanation:
A. Determination of the final velocity.
½mv² = mgh
Cancel out m
½v² = gh
Cross multiply
v² = 2gh
Take the square root of both side
v = √2gh
B. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is no mass (m) in the formula.
Thus, the final velocity does not depend on the mass of the car.
C. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is height (h) in the formula.
Thus, the final velocity depends on the steepness of the hill
D. Determination of the final velocity.
Height (h) = 0.55 m
Acceleration due to gravity (g) = 9.8 m/s²
Velocity (v) =?
v = √2gh
v = √(2 × 9.8 × 0.55)
v = √10.78
v = 3.28 m/s
A 50kg mass is sitting on a frictionless surface. An unknown constant force pushes the mass for 2 seconds until the mass reaches a velocity of 3m/s. What was the force acting on the mass?
Answer:
75N
Explanation:
a = v/t = 3/2
F = ma = 50(3/2) = 75
Standing at a crosswalk, you hear a frequency of 530 Hz from the siren of an approaching ambulance. After the ambulance passes, the observed frequency of the siren is 424 Hz. Determine the ambulance's speed from these observations.
Answer:
_s = 37.77 m / s
Explanation:
This is an exercise of the Doppler effect that the change in the frequency of the sound due to the relative speed of the source and the observer, in this case the observer is still and the source is the one that moves closer to the observer, for which relation that describes the process is
f ’= f₀ [tex]\frac{v}{v - v_s}[/tex]
where d ’= 530 Make
when the ambulance passes away from the observer the relationship is
f ’’ = f₀ [tex]\frac{v}{v + v_s}[/tex]
where d ’’ = 424 beam
let's write the two expressions
f ’ (v-v_s) = fo v
f ’’ (v + v_s) = fo v
let's solve the system, subtract the two equations
v (f ’- f’ ’) - v_s (f’ + f ’’) = 0
v_s = v [tex]\frac{ f' - f''}{ f' + f''}[/tex]
the speed of sound is v = 340 m / s
let's calculate
v_s = 340 [tex](\frac{ 530 -424}{530+424} )[/tex]
v_s = 340 [tex](\frac{106}{954}[/tex])
v_s = 37.77 m / s
1. A block with mass 20 kg is
sliding up a plane (Ukinetic=0.3,
inclined at 10°) at a speed of
2 m/s to the right (positive
X-direction). How far does it
go up along the plane before
it comes to rest momentarily?
Answer: 0.435 m
Explanation:
Given
mass m=20 kg
initial speed u=2 m/s
coefficient of kinetic friction [tex]\mu_k=0.3[/tex]
deceleration which opposes the motion is given by
[tex]\Rightarrow a=g\sin \theta+\mu_kg\cos \theta\\\Rightarrow a=g(\sin \theta +\mu_k\cos \theta)[/tex]
[tex]\Rightarrow a=9.8(\sin 10^{\circ}+0.3\times \cos 10^{\circ})\\\Rightarrow a=4.59\ m/s^2[/tex]
using [tex]v^2-u^2=2as[/tex]
[tex]\Rightarrow s=\dfrac{2^2}{2\times 4.59}=0.435\ m[/tex]
39. What is the change in momentum for a 5,000 kg ship in
outer space that experiences no net force over a 1 hr
period?
Answer:
Change in momentum is zero.
Explanation:
The following data were obtained from the question:
Mass (m) = 5000 kg
Time (t) = 1 h
Net force (F) = 0
Change in momentum =?
Force = Rate of change of momentum
0 = change in momentum
Change in momentum = 0
We can see from the above illustration that the net force is zero. Thus, the change in momentum is also zero.
what is the effect of divorce on females?
Answer:
Numerous studies have shown that the economic costs of divorce fall more heavily on women. After separation, women experience a sharper decline in household income and a greater poverty risk (Smock 1994; Smock and Manning
Answer:
sadness and stress...................
A bicyclist rides 5.0 km due east, while the resistive forcefrom the air has a magnitude of 3.0 N and points due west. Therider then turns around and rides 5.0 km due west, back to herstarting point. The resistive force from the air on the return triphas a magnitude of 3.0 N and points due east.
a) Find the work done by the resistive force during the roundtrip.
Based on answer in part A.
b) Is the resistive force a conservative force? explain.
Answer:
a) Find the work done by the resistive force during the roundtrip.
W=-30kJ
b) Is the resistive force a conservative force? explain.
The resistive force is not a conservative force since the work done during the round trip is not zero
Explanation:
The worf done on object y a constant force F is given by:
W= (F cos ∅)S
Where S is the displacement and ∅ is the angle between the force and the displacement.
The displacement of the bicycle during each part of the trip is s=5000m and teh magnitude of teh resistance force is F=3.0N
∅1=180° he angle between the displacement and the force
W1=W2
W1 = (3.0 cos180) 5000m
W1=-15.O kJ
W=W1+W2
W=-30kJ
The resistive force is not a conservative force since the work done during the round trip is not zero
(a) The work done by the resistive force is 15,000 J
(b) The work done the resistive force is non-conservative since the resultant resistive force in not zero.
Work doneWork is said to be when an applied force displaces an object from its initial position.
Work done by resistive forceThe work done by the resistive force is calculated as follows;
W = FΔr
W = 3 x (5,000 - 0)
W = 15,000 J
Thus, the work done the resistive force is non-conservative since the resultant resistive force in not zero.
Learn more about conservative force here: https://brainly.com/question/15357875
The sides of a right triangle that has any given vector for the hypotenuse are called _____
A. Scalar
B. Component
C. Resultant
D. Vector
Answer:
They are the resultant vector.
A particle move in the xy plane so that its position vector r=bcosQi +bsinQj+ ctk, where b, Q and c are constants. show that the partial move with constant speed.
Answer:
The speed of this particle is constantly [tex]c[/tex].
Explanation:
Position vector of this particle at time [tex]t[/tex]:
[tex]\displaystyle \mathbf{r}(t) = b\, \cos(Q)\, \mathbf{i} + b\, \sin(Q) \, \mathbf{j} + c\, t\, \mathbf{k}[/tex].
Write [tex]\mathbf{r}(t)[/tex] as a column vector to distinguish between the components:
[tex]\mathbf{r}(t) = \begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}[/tex].
Both [tex]b[/tex] and [tex]Q[/tex] are constants. Therefore, [tex]b\, \cos(Q)[/tex] and [tex]b \sin (Q)[/tex] would also be constants with respect to [tex]t[/tex]. Hence, [tex]\displaystyle \frac{d}{dt}[b\, \cos(Q)] = 0[/tex] and [tex]\displaystyle \frac{d}{dt}[b\, \sin(Q)] = 0[/tex].
Differentiate [tex]\mathbf{r}(t)[/tex] (component-wise) with respect to time [tex]t[/tex] to find the velocity vector of this particle at time [tex]t\![/tex]:
[tex]\begin{aligned}\mathbf{v}(t) &= \frac{\rm d}{{\rm d} t} [\mathbf{r}(t)] \\ &=\frac{\rm d}{{\rm d} t} \left(\begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}\right) \\ &= \begin{bmatrix}\displaystyle \frac{d}{dt}[b\, \cos(Q)] \\[0.5em] \displaystyle \frac{d}{dt}[b\, \sin(Q)]\\[0.5em]\displaystyle \frac{d}{dt}[c \cdot t]\end{bmatrix} = \begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\end{aligned}[/tex].
The speed [tex]v[/tex] (a scalar) of a particle is the magnitude of its velocity :
[tex]\begin{aligned}v(t) &= \| \mathbf{v}(t) \| \\ &= \left\|\begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\right\| \\ &= \sqrt{0^2 + 0^2 + c^2} = c\end{aligned}[/tex].
Therefore, the speed of this particle is constantly [tex]c[/tex] (a constant.)
A skater with an initial speed of 5.90 m/s stops propelling himself and begins to coast across the ice, eventually coming to rest. Air resistance is negligible. (a) The coefficient of kinetic friction between the ice and the skate blades is 0.0500. Find the deceleration caused by kinetic friction. (b) How far will the skater travel before coming to rest
Answer:a) - 0.4905 m/s² b) distance = 35.48 m
Explanation:
Given that
The initial velocity of the skater = 5.90 m/s
kinetic friction coefficient = 0.0500
final velocity = 0 m/s(since it comes to rest)
deceleration cause by the kinetic friction = ?
we know that
F = μN
and N= mg
Therefore;
F = μ m g....................(1)
also that
F = m a........................(2)
with our common Force, F, equating (1) and (2), we have that
m a = - μ m g
a = - μ g
a = - 0.05 × 9.81
a = - 0.4905 m/s²
The deceleration cause by the kinetic friction is a = - 0.4905 m/s²
b)
The distance the skater travels before stopping
is given as
Vf² = v₀² - 2 a x
final velocity = 0 m/s(since it comes to rest)
Therefore We have that
0 = v₀² - 2 a x
x = - v₀² / 2 a
x = 5.90² / (2 x 0.4905 )
34.81/0.981
x = 35.48 m
Or
using
v²-u² = 2aS final velocity = 0 m/s(since it comes to rest)
0²-5.90² = -2×0.4905×S
34.81=0.981S
S= 34.81/0.981
S=35.48m
What is a black hole's escape velocity?
The simplest definition of a black hole is an object that is so dense that not even light can escape its surface. If we squished the Earth's mass into a sphere with a radius of 9 mm, the escape velocity would be the speed of light. Just a wee-bit smaller, and the escape velocity is greater than the speed of light.
HopeItHelps!
what are the types of energy sources based on
time of replacement ? write down their names
Answer:
solar energy
wind power
geothermal energy
hydraulic power
biomass energy
energy storage
(That's all I know).
what is the average velocity of a van that moves from 0 to 60 m east and 20 seconds
Explanation:
I have a lot to say it was very nice to meet my parents are u doing well I dont want too its been so much I love you so I was like u know I am not a man but you are the auditions I have been in a long long long life is a triangle and a chair for me and my parents think about the way I
1. With the exception to water, matter (expands, contracts) when it gets
hotter. *
A)Expands
B)Contracts
Which statement best compares potential and kinetic energy?
O Objects always have more potentiał energy than kinetic energy.
O Kinetic energy increases and potential energy decreases when the velocity of an object increases
O Only potential energy decreases when an object's height increases.
O Objects always have more kinetic energy than potential energy.
Answer:
Kinetic energy increases and potential energy decrease when velocity of an object increase.
You are standing on the bottom of a lake with your torso above water. Which statement is correct?
a. You feel a buoyant force only when you momentarily jump up from the bottom of the lake.
b. There is a buoyant force that is proportional to the weight of your body below the water level.
c. There is a buoyant force that is proportional to the volume of your body that is below the level of the water.
d. There is no buoyant force on you since you are supported by the lake bottom.
Answer:
c. There is a buoyant force that is proportional to the volume of your body that is below the level of the water.
Explanation:
Buoyancy can be defined as a force which is created by the water displaced by an object.
Simply stated, buoyancy is directly proportional to the amount of water that is being displaced by an object.
Hence, the greater the amount of water an object displaces; the greater is the force of buoyancy pushing the object up.
The buoyancy of an object is given by the formula;
[tex] Fb = pgV [/tex]
[tex] But, \; V = Ah [/tex]
[tex] Hence, \; Fb = pgAh [/tex]
Where;
Fb = buoyant force of a liquid acting on an object.
g = acceleration due to gravity.
p = density of the liquid.
v = volume of the liquid displaced.
h = height of liquid (water) displaced by an object.
A = surface area of the floating object.
The unit of measurement for buoyancy is Newton (N).
In this scenario, you are standing on the bottom of a lake with your torso above water. Thus, there is a buoyant force that is proportional to the volume of your body that is below the level of the water.
Identical balls are dropped from the same initial height and bounce back to half the initial height. In Case 1, the ball bounces off a cement floor, and in Case 2, the ball bounces off a piece of stretchy rubber. Two cases of a ball dropping and bouncing off of a surface. In case one, the ball approaches a cement floor, comes in contact, momentarily comes to rest, and then bounces off with a velocity smaller than the approach velocity. In case 2, the ball approaches a piece of stretchy rubber. When the ball comes in contact with the rubber, it deforms the rubber and comes momentarily to rest. The ball bounces off again with a velocity smaller than the approach velocity, and the rubber regains its original shape. In both cases, the balls are dropped from the same initial height and reach the same final height. In which case is the magnitude of the ball's change in momentum the greatest
Answer:
the impulse must be the same in these two cases F t = m ([tex]\sqrt{2g h_f } - \sqrt{2g h_o}[/tex])
Explanation:
For this exercise we use the relationship between momentum and momentum
I = Δp
F t = m v_f - m v₀
To know the speed we use the conservation of energy
starting point. Highest point
Em₀ = U = m g h
fincla point. Just before the crash
Em_f = K = ½ m v²
energy is conserved
Em₀ = Em_f
m g h = ½ m v²
v = [tex]\sqrt{2gh}[/tex]
we substitute in the impulse relation
F t = m ([tex]\sqrt{2g h_f } - \sqrt{2g h_o}[/tex])
therefore we can see that as in case the initial and final heights are equal, the impulse must be the same in these two cases
Cameron is standing on the edge of a 60 m high cliff. He horizontally throws a football
with an initial velocity of 10 m/s. How long does it take for the football to hit the
ground?
Answer:34.6 m/s
Explanation: It is asking how long meaning the answer is in time
help please i will mark brainlist!!!
Answer:
.50 M
Explanation:
5*.50=2.5 + 2*.25=.5 = 3n
6*.50= 3N
Final answer is .50M
A spring with a constant of 76 N/m is extended by 0.9 m. How much energy is stored in the extended spring?
Answer:
[tex]E=30.78\ J[/tex]
Explanation:
The force constant of the spring, k = 76 N/m
The extension in the spring, x = 0.9 m
We need to find the energy is stored in the extended spring. The energy stored in the spring is given by :
[tex]E=\dfrac{1}{2}kx^2\\\\E=\dfrac{1}{2}\times 76\times (0.9)^2\\\\E=30.78\ J[/tex]
So, 30.78 J of energy is stored in the spring.
4. Which of these is exerted by an engine?
(1 Point)
Thrust
Water resistance
Friction
Air resistance
Air resistance is exerted by an engine
Albert Bandura emphasized the idea of __________, which is the belief one has in one’s own ability to succeed. A. operant conditioning B. determinism C. self-efficacy D. self-worth
Answer:
C
Explanation:
Albert Bandura emphasized the idea of Self efficacy which is the belief one has in one’s own ability to succeed.
What is Self efficacy?
A person's self-efficacy relates to their confidence in their ability to carry out the behaviors required to achieve particular performance goals (Bandura, 1977, 1986, 1997).
The belief in one's capacity to exercise control over one's own motivation, behavior, and social environment is known as self-efficacy. The goals for which people strive, the amount of effort put out to obtain goals, and the possibility of achieving particular levels of behavioral performance are all influenced by these cognitive self-evaluations.
Self-efficacy beliefs, unlike conventional psychological notions, are anticipated to change according to the operating domain and the environment in which an action occurs.
Therefore, Albert Bandura emphasized the idea of Self efficacy which is the belief one has in one’s own ability to succeed.
To learn more about Self efficacy, refer to the link:
https://brainly.com/question/28215515
#SPJ6
Two charged point-like objects are located on the x-axis. The point-like object with charge q1 = 4.60 µC is located at x1 = 1.25 cm and the point-like object with charge q2 = −2.14 µC is located at x2 = −1.80 cm.
A) Determine the total electric potential (in V) at the origin.
B) Determine the total electric potential (in V) at the point with coordinates (0, 1.50 cm).
Answer:
a) the total electric potential is 2282000 V
b) the total electric potential (in V) at the point with coordinates (0, 1.50 cm) is 1330769.23 V
Explanation:
Given the data in the question and as illustrated in the image below;
a) Determine the total electric potential (in V) at the origin.
We know that; electric potential due to multiple charges is equal to sum of electric potentials due to individual charges
so
Electric potential at p in the diagram 1 below is;
Vp = V1 + V2
Vp = kq1/r1 + kq2/r2
we know that; Coulomb constant, k = 9 × 10⁹ C
q1 = 4.60 uC = 4.60 × 10⁻⁶ C
r1 = 1.25 cm = 0.0125 m
q2 = -2.06 uC = -2.06 × 10⁻⁶ C
location x2 = −1.80 cm; so r2 = 1.80 cm = 0.018 m
so we substitute
Vp = ( 9 × 10⁹ × 4.60 × 10⁻⁶/ 0.0125 ) + ( 9 × 10⁹ × -2.06 × 10⁻⁶ / 0.018 )
Vp = (3312000) + ( -1030000 )
Vp = 3312000 -1030000
Vp = 2282000 V
Therefore, the total electric potential is 2282000 V
b)
the total electric potential (in V) at the point with coordinates (0, 1.50 cm).
As illustrated in the second image;
r1² = 0.015² + 0.0125²
r1 = √[ 0.015² + 0.0125² ]
r1 = √0.00038125
r1 = 0.0195
Also
r2² = 0.015² + 0.018²
r2 = √[ 0.015² + 0.018² ]
r2 = √0.000549
r2 = 0.0234
Now, Electric Potential at P in the second image below will be;
Vp = V1 + V2
Vp = kq1/r1 + kq2/r2
we substitute
Vp = ( 9 × 10⁹ × 4.60 × 10⁻⁶/ 0.0195 ) + ( 9 × 10⁹ × -2.06 × 10⁻⁶ / 0.0234 )
Vp = 2123076.923 + ( -762962.962 )
Vp = 2123076.923 -792307.692
Vp = 1330769.23 V
Therefore, the total electric potential (in V) at the point with coordinates (0, 1.50 cm) is 1330769.23 V
a) The total electric potential is 2282000 V
b) The total electric potential (in V) at the point with coordinates (0, 1.50 cm) is 1330769.23 V
What is electric potential?The electric potential is defined as the amount of work energy needed to move a unit of electric charge from a reference point to a specific point in an electric field.
Given the data in the question and as illustrated in the image below;
a) Determine the total electric potential (in V) at the origin.
We know that; electric potential due to multiple charges is equal to sum of electric potentials due to individual charges
Electric potential at p in diagram 1 below is;
[tex]V_P=V_1+V_2[/tex]
[tex]Vp = \dfrac{kq_1}{r_1} + \dfrac{kq_2}{r_2}[/tex]
we know that; the Coulomb constant, k = 9 × 10⁹ C
q1 = 4.60 uC = 4.60 × 10⁻⁶ C
r1 = 1.25 cm = 0.0125 m
q2 = -2.06 uC = -2.06 × 10⁻⁶ C
location x2 = −1.80 cm; so r2 = 1.80 cm = 0.018 m
so we substitute
Vp = ( 9 × 10⁹ × 4.60 × 10⁻⁶/ 0.0125 ) + ( 9 × 10⁹ × -2.06 × 10⁻⁶ / 0.018 )
Vp = (3312000) + ( -1030000 )
Vp = 3312000 -1030000
Vp = 2282000 V
Therefore, the total electric potential is 2282000 V
b)The total electric potential (in V) at the point with coordinates (0, 1.50 cm).
As illustrated in the second image;
[tex]r_1^2=0.015^2+0.0125^2[/tex]
[tex]r_1 = \sqrt{[ 0.015^2 + 0.0125^2 ][/tex]
[tex]r_1 = \sqrt{0.00038125}[/tex]
[tex]r_1 = 0.0195[/tex]
Also
[tex]r_2^2 = 0.015^2 + 0.018^2[/tex]
[tex]r_2 = \sqrt{0.015^2 + 0.018^2}[/tex]
[tex]r_2 = \sqrt{0.000549[/tex]
[tex]r_2 = 0.0234[/tex]
Now, Electric Potential at P in the second image below will be;
Vp = V1 + V2
[tex]Vp = \dfrac{kq_1}{r_1} + \dfrac{kq_2}{r_2}[/tex]
we substitute
Vp = ( 9 × 10⁹ × 4.60 × 10⁻⁶/ 0.0195 ) + ( 9 × 10⁹ × -2.06 × 10⁻⁶ / 0.0234 )
Vp = 2123076.923 + ( -762962.962 )
Vp = 2123076.923 -792307.692
Vp = 1330769.23 V
Therefore, the total electric potential (in V) at the point with coordinates (0, 1.50 cm) is 1330769.23 V
To know more about electric potential follow
https://brainly.com/question/25923373