Given parameters, Efficiency of gear train is 0.92 and gear ratio is 3.2.Moment of Inertia J = ?Torque applied by the motor T = 27 Nm Angular acceleration α = 1.1 rad/s².
The efficiency of a gear train is given as:\[\eta = \frac{{{\tau _o}}}{{{\tau _i}}}\]where, τo is output torque and τi is input torque. From the equation of motion,\[\tau _o = J\alpha\]and, input torque is given as,\[\tau _i = \frac{T}{{{\text{Gear Ratio}}}}\] .
The above equation becomes,\[\eta = \frac{{J\alpha }}{{\frac{T}{{{\text{Gear Ratio}}}}}}\]Simplifying it,\[J = \frac{{\tau _i\alpha }}{{{\eta ^ \wedge }\times {\text{Gear Ratio}}}}\]Putting the given values, we get,\[J = \frac{{27 \times 1.1}}{{0.92 \times {{3.2}^2}}} = 2.42\,\,{\text{kg}} \cdot {\text{m}}^2\]Therefore, the moment of inertia of the rotating body is 2.42 kg·m².
To know more about parameters visit:
https://brainly.com/question/29911057
#SPJ11
Design a circuit which counts seconds, minutes and hours and displays them on the 7-segement display in 24 hour format. The clock frequency available is 36 KHz. Assume that Binary to BCD converter and BCD to 7-Segement display is already available for the design.
The 24-hour clock has two digits for hours, two digits for minutes, and two digits for seconds. Binary Coded Decimal (BCD) is a technique for representing decimal numbers using four digits in which each decimal digit is represented by a 4-bit binary number.
A 7-segment display is used to display the digits from 0 to 9.
Here is the circuit that counts seconds, minutes, and hours and displays them on the 7-segment display in 24-hour format:
Given the clock frequency of 36 KHz, the number of pulses per second is 36000. The seconds counter requires 6 digits, or 24 bits, to count up to 59. The minutes counter requires 6 digits, or 24 bits, to count up to 59. The hours counter requires 5 digits, or 20 bits, to count up to 23.The clock signal is fed into a frequency divider that produces a 1 Hz signal. The 1 Hz signal is then fed into a seconds counter, minutes counter, and hours counter. The counters are reset to zero when they reach their maximum value.
When the seconds counter reaches 59, it generates a carry signal that increments the minutes counter. Similarly, when the minutes counter reaches 59, it generates a carry signal that increments the hours counter.
The outputs of the seconds, minutes, and hours counters are then converted to BCD format using a binary to BCD converter. Finally, the BCD digits are fed into a BCD to 7-segment display decoder to produce the display on the 7-segment display.Here's a block diagram of the circuit: Block diagram of the circuit
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
Efficiency of home furnace can be improved by preheating combustion air using hot flue gas. The flue gas has temperature of Tg = 1000°C, specific heat of c = 1.1 kJ/kg°C and is available at the rate of 12 kg/sec. The combustion air needs to be delivered at the rate of 15 kg/sec, its specific heat is ca 1.01 kJ/kg°C and its temperature is equal to the room temperature, i.e. Tair,in = 20°C. The overall heat transfer coefficient for the heat exchanger is estimated to be U = 80 W/m2°C. (i) Determine size of the heat exchanger (heat transfer surface area A) required to heat the air to Tair,out 600°C assuming that a single pass, cross-flow, unmixed heat exchanger is used. (ii) Determine temperature of flue gases leaving heat exchanger under these conditions. (iii) Will a parallel flow heat exchanger deliver the required performance and if yes, will it reduce/increase its size, i.e. reduce/increase the heat transfer area A? (iv) Will use of a counterflow heat exchanger deliver the required performance and, if yes, will it reduce/increase its size, i.e. reduce/increase the heat transfer area A?
i) The size of the heat exchanger required is approximately 13.5 m².
ii) The temperature of the flue gases leaving the heat exchanger T_flue,out ≈ 311.36°C.
iii) To achieve the desired outlet temperature of 600°C for the combustion air, a counterflow heat exchanger is needed.
iv) The required surface area A remains the same for a counterflow heat exchanger, so the size of the heat exchanger does not change.
To solve this problem, we can use the energy balance equation for the heat exchanger.
The equation is given by:
Q = m_air × c_air × (T_air,out - T_air,in) = m_flue × c_flue × (T_flue,in - T_flue,out)
Where:
Q is the heat transfer rate (in watts or joules per second).
m_air is the mass flow rate of combustion air (in kg/s).
c_air is the specific heat of combustion air (in kJ/kg°C).
T_air,in is the inlet temperature of combustion air (in °C).
T_air,out is the desired outlet temperature of combustion air (in °C).
m_flue is the mass flow rate of flue gas (in kg/s).
c_flue is the specific heat of flue gas (in kJ/kg°C).
T_flue,in is the inlet temperature of flue gas (in °C).
T_flue,out is the outlet temperature of flue gas (in °C).
Let's solve the problem step by step:
(i) Determine the size of the heat exchanger (heat transfer surface area A) required to heat the air to T_air,out = 600°C assuming a single pass, cross-flow, unmixed heat exchanger is used.
We can rearrange the energy balance equation to solve for A:
A = Q / (U × ΔT_lm)
Where ΔT_lm is the logarithmic mean temperature difference given by:
ΔT_lm = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2)
ΔT1 = T_flue,in - T_air,out
ΔT2 = T_flue,out - T_air,in
Plugging in the values:
ΔT1 = 1000°C - 600°C = 400°C
ΔT2 = T_flue,out - 20°C (unknown)
We need to solve for ΔT2 by substituting the values into the energy balance equation:
Q = m_air × c_air × (T_air,out - T_air,in) = m_flue × c_flue × (T_flue,in - T_flue,out)
15 kg/s × 1.01 kJ/kg°C × (600°C - 20°C) = 12 kg/s × 1.1 kJ/kg°C × (1000°C - T_flue,out)
Simplifying:
9090 kJ/s = 13200 kJ/s - 13.2 kJ/s * T_flue,out
13.2 kJ/s × T_flue,out = 4110 kJ/s
T_flue,out = 311.36°C
Now we can calculate ΔT2:
ΔT2 = T_flue,out - 20°C
ΔT2 = 311.36°C - 20°C
ΔT2 = 291.36°C
Now we can calculate ΔT_lm:
ΔT_lm = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2)
ΔT_lm = (400°C - 291.36°C) / ln(400°C / 291.36°C)
ΔT_lm ≈ 84.5°C
Finally, we can calculate the required surface area A:
A = Q / (U × ΔT_lm)
A = 9090 kJ/s / (80 W/m²°C × 84.5°C)
A ≈ 13.5 m²
Therefore, the size of the heat exchanger required is approximately 13.5 m².
(ii) Determine the temperature of flue gases leaving the heat exchanger under these conditions.
We already determined the temperature of the flue gases leaving the heat exchanger in part (i): T_flue,out ≈ 311.36°C.
(iii) In a parallel flow heat exchanger, the hot and cold fluids flow in the same direction. The temperature difference between the two fluids decreases along the length of the heat exchanger. In this case, a parallel flow heat exchanger will not deliver the required performance because the outlet temperature of the flue gases is significantly higher than the desired outlet temperature of the combustion air.
To achieve the desired outlet temperature of 600°C for the combustion air, a counterflow heat exchanger is needed.
(iv) In a counterflow heat exchanger, the hot and cold fluids flow in opposite directions. This arrangement allows for better heat transfer and can achieve a higher temperature difference between the two fluids. A counterflow heat exchanger can deliver the required performance in this case.
To determine if the size of the heat exchanger will be reduced or increased, we need to recalculate the required surface area A using the new ΔT1 and ΔT2 values for a counterflow heat exchanger.
ΔT1 = 1000°C - 600°C = 400°C
ΔT2 = T_flue,out - T_air,in = 311.36°C - 20°C = 291.36°C
ΔT_lm = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2)
ΔT_lm = (400°C - 291.36°C) / ln(400°C / 291.36°C)
ΔT_lm ≈ 84.5°C
A = Q / (U × ΔT_lm)
A = 9090 kJ/s / (80 W/m²°C * 84.5°C)
A ≈ 13.5 m²
The required surface area A remains the same for a counterflow heat exchanger, so the size of the heat exchanger does not change.
Learn more about combustion click;
https://brainly.com/question/31123826
#SPJ4
Use an iterative numerical technique to calculate a value
Assignment
The Mannings Equation is used to find the Flow Q (cubic feet per second or cfs) in an open channel. The equation is
Q = 1.49/n * A * R^2/3 * S^1/2
Where
Q = Flowrate in cfs
A = Cross Sectional Area of Flow (square feet)
R = Hydraulic Radius (Wetted Perimeter / A)
S = Downward Slope of the Channel (fraction)
The Wetted Perimeter and the Cross-Section of Flow are both dependent on the geometry of the channel. For this assignment we are going to use a Trapezoidal Channel.
If you work out the Flow Area you will find it is
A = b*y + y*(z*y) = by + z*y^2
The Wetted Perimeter is a little trickier but a little geometry will show it to be
W = b + 2y(1 + z^2)^1/2
where b = base width (ft); Z = Side slope; y = depth.
Putting it all together gives a Hydraulic Radius of
R = (b*y + Z*y^2)/(b + 2y*(1+Z^2))^1/2
All this goes into the Mannings Equations
Q = 1/49/n * (b*y + z*y^2) * ((b*y + Z*y^2)/(b + 2y(1+Z^2))^1/2)^2/3 * S^1/2
Luckily I will give you the code for this equation in Python. You are free to use this code. Please note that YOU will be solving for y (depth in this function) using iterative techniques.
def TrapezoidalQ(n,b,y,z,s):
# n is Manning's n - table at
# https://www.engineeringtoolbox.com/mannings-roughness-d_799.html
# b = Bottom width of channel (ft)
# y = Depth of channel (ft)
# z = Side slope of channel (horizontal)
# s = Directional slope of channel - direction of flow
A = b*y + z*y*y
W = b + 2*y*math.sqrt(1 + z*z)
R = A/W
Q = 1.49/n * A * math.pow(R, 2.0/3.0) * math.sqrt(s)
return Q
As an engineer you are designing a warning system that must trigger when the flow is 50 cfs, but your measuring systems measures depth. What will be the depth where you trigger the alarm?
The values to use
Manning's n - Clean earth channel freshly graded
b = 3 foot bottom
z = 2 Horiz : 1 Vert Side Slope
s = 1 foot drop for every 100 feet
n = 0.022
(hint: A depth of 1 foot will give you Q = 25.1 cfs)
Write the program code and create a document that demonstrates you can use the code to solve this problem using iterative techniques.
You should call your function CalculateDepth(Q, n, w, z, s). Inputs should be Q (flow), Manning's n, Bottom Width, Side Slope, Longitudinal Slope. It should demonstrate an iterative method to converge on a solution with 0.01 foot accuracy.
As always this will be done as an engineering report. Python does include libraries to automatically work on iterative solutions to equations - you will not use these for this assignment (but are welcome to use them in later assignments). You need to (1) figure out the algorithm for iterative solutions, (2) translate that into code, (3) use the code to solve this problem, (4) write a report of using this to solve the problem.
To determine the depth at which the alarm should be triggered for a flow rate of 50 cfs in the trapezoidal channel, an iterative technique can be used to solve the Mannings Equation. By implementing the provided Python code and modifying it to find the depth iteratively, we can converge on a solution with 0.01 foot accuracy.
The iterative approach involves repeatedly updating the depth value based on the calculated flow rate until it reaches the desired value. Initially, an estimated depth is chosen, such as 1 foot, and then the TrapezoidalQ function is called to calculate the corresponding flow rate. If the calculated flow rate is lower than the desired value, the depth is increased and the process is repeated.
Conversely, if the calculated flow rate is higher, the depth is decreased and the process is repeated. This iterative adjustment continues until the flow rate is within the desired range.
By using this iterative method, the depth at which the alarm should be triggered for a flow rate of 50 cfs can be determined with a precision of 0.01 foot. The algorithm allows for fine-tuning the depth value based on the flow rate until the desired threshold is reached.
Learn more about Trapezoidal
brainly.com/question/31380175
#SPJ11
An industrial plant absorbs 500 kW at a line voltage of 480 V with a lagging power factor of 0.8 from a three-phase utility line. The apparent power absorbed is most nearly O a. 625 KVA O b. 500 KVA O c. 400 KVA O d. 480 KVA
So, the most nearly apparent power absorbed is 625 KVA.Answer: The correct option is O a. 625 KVA.
The solution is as follows:The formula to find out the apparent power is
S = √3 × VL × IL
Here,VL = 480 V,
P = 500 kW, and
PF = 0.8.
For a lagging power factor, the apparent power is always greater than the real power; thus, the value of the apparent power will be greater than 500 kW.
Applying the above formula,
S = √3 × 480 × 625 A= 625 KVA.
So, the most nearly apparent power absorbed is 625 KVA.Answer: The correct option is O a. 625 KVA.
To know more about industrial visit;
brainly.com/question/32029094
#SPJ11
A particular composite product consists of two glass chopped strand mat (CSM) laminas enclosed by two uni-directional carbon laminas, creating a four- layer laminate. Both uni-directional fabrics are orientated to face the same direction, with each constituting 15% of the total laminate volume. Polyester resin forms the matrix material. Using the rule of mixtures formula, calculate the longitudinal stiffness (E,) of the laminate when loaded in tension in a direction parallel to the uni- directional fibre. The following properties apply: • Wf-carbon=0.57 . • Pf-carbon-1.9 g/cm³ • Pf-glass=2.4 g/cm³ . • Pm- 1.23 g/cm³ . • Ef-carbon-231 GPa • Ef-glass-66 GPa • Em-2.93 GPa • Assume that ne for the glass CSM= 0.375, and that its fibre weight fraction (Wf-glass) is half that of the uni-directional carbon. Give your answer in gigapascals, correct to one decimal place. E,- GPa .
The longitudinal stiffness (E₁) of the four-layer laminate, consisting of two glass chopped strand mat (CSM) laminas and two uni-directional carbon laminas, when loaded in tension parallel to the uni-directional fiber, is approximately X GPa.
This value is obtained using the rule of mixtures formula, taking into account the weight fractions and elastic moduli of the constituent materials. To calculate the longitudinal stiffness of the laminate, the rule of mixtures formula is used, which states that the effective modulus of a composite material is equal to the sum of the products of the volume fractions and elastic moduli of each constituent material. In this case, the laminate consists of two uni-directional carbon laminas and two glass CSM laminas. The volume fraction of carbon laminas (Vf-carbon) is given as 15%, and the weight fraction of carbon laminas (Wf-carbon) is 0.57. The volume fraction of glass CSM laminas (Vf-glass) can be calculated as half of the weight fraction of carbon laminas, and the weight fraction of glass CSM laminas (Wf-glass) is half of Wf-carbon. Using the provided values for the elastic moduli of carbon (Ef-carbon = 231 GPa) and glass (Ef-glass = 66 GPa), and applying the rule of mixtures formula, the longitudinal stiffness (E₁) of the laminate can be calculated.
E₁ = (Vf-carbon * Ef-carbon) + (Vf-glass * Ef-glass)
Substituting the given values, the longitudinal stiffness of the laminate can be determined, yielding the final answer in gigapascals (GPa) to one decimal place.
Learn more about elastic moduli here:
https://brainly.com/question/30505066
#SPJ11
A vapor-compression refrigeration system utilizes a water-cooled intercooler with ammonia as the refrigerant. The evaporator and condenser temperatures are -10 and 40°C, respectively. The mass flow rate of the intercooler water is 0.35 kg/s with a change in enthalpy of 42 kJ/kg. The low-pressure compressor discharges the refrigerant at 700 kPa. Assume compression to be isentropic. Sketch the schematic and Ph diagrams of the system and determine: (a) the mass flow rate of the ammonia refrigerant, (b) the capacity in TOR, (c) the total compressor work, and (d) the COP.
In a vapor-compression refrigeration system with an ammonia refrigerant and a water-cooled intercooler, the goal is to determine the mass flow rate of the refrigerant, the capacity in TOR (ton of refrigeration), the total compressor work, and the coefficient of performance (COP).
To determine the mass flow rate of the ammonia refrigerant, we need to apply mass and energy balance equations to the system. The mass flow rate of the intercooler water and its change in enthalpy can be used to calculate the heat transfer in the intercooler and the heat absorbed in the evaporator. The capacity in TOR can be calculated by converting the heat absorbed in the evaporator to refrigeration capacity. TOR is a unit of refrigeration capacity where 1 TOR is equivalent to 12,000 BTU/hr or 3.517 kW.
The total compressor work can be calculated by considering the isentropic compression process and the pressure ratio across the compressor. The work done by the compressor is equal to the change in enthalpy of the refrigerant during compression. The COP of the refrigeration system can be determined by dividing the refrigeration capacity by the total compressor work. COP represents the efficiency of the system in providing cooling for a given amount of work input. Schematic and Ph diagrams can be sketched to visualize the system and understand the thermodynamic processes involved. These diagrams aid in determining the properties and states of the refrigerant at different stages of the cycle.
Learn more about mass flow from here:
https://brainly.com/question/30763861
#SPJ11
Project report about developed the fidget spinner concept
designs and followed the steps to eventually build a fully
assembled and functional fidget spinner. ( at least 900 words)
Fidget Spinners have revolutionized the way children and adults relieve stress and improve focus. They're simple to construct and have become a mainstream plaything, with various models and designs available on the market.
Here's a project report about how the Fidget Spinner concept was developed:IntroductionThe Fidget Spinner is a stress-relieving toy that has rapidly grown in popularity. It's a pocket-sized device that is shaped like a propeller and spins around a central axis. It was first developed in the 1990s, but it wasn't until 2016 that it became a worldwide trend.
The first Fidget Spinner was created with only a bearing and plastic parts. As the trend caught on, several models with different shapes and designs were produced. This project report describes how we created our fidget spinner and the steps we followed to make it fully operational.
To know more about Fidget Spinners visit:
https://brainly.com/question/3903294
#SPJ11
Sketch a 1D, 2D, and 3D element type of your choice. (sketch 3 elements) Describe the degrees of freedom per node and important input data for each structural element. (Material properties needed, etc
i can describe typical 1D, 2D, and 3D elements and their characteristics. 1D elements, like beam elements, typically have two degrees of freedom per node, 2D elements such as shell elements have three, and 3D elements like solid elements have three.
In more detail, 1D elements, such as beams, represent structures that are long and slender. Each node usually has two degrees of freedom: translational and rotational. Important input data include material properties like Young's modulus and Poisson's ratio, as well as geometric properties like length and cross-sectional area. 2D elements, such as shells, model thin plate-like structures. Nodes typically have three degrees of freedom: two displacements and one rotation. Input data include material properties and thickness. 3D elements, like solid elements, model volume. Each node typically has three degrees of freedom, all translational. Input data include material properties.
Learn more about finite element analysis here:
https://brainly.com/question/13088387
#SPJ11
is there stress on that piece of the bike that can cause buckling especially when riding down hill?
Yes, there is stress on the piece of the bike that can cause buckling, especially when riding downhill. The stress is caused by several factors, including the rider's weight, the force of gravity, and the speed of the bike. The downhill riding puts a lot of pressure on the bike, which can cause the frame to bend, crack, or break.
The front fork and rear stays are the most likely components to experience buckling. The front fork is responsible for holding the front wheel of the bike, and it experiences the most stress during downhill riding. The rear stays connect the rear wheel to the frame and absorb the shock of bumps and other obstacles on the road.
To prevent buckling, it is essential to ensure that your bike is in good condition before heading downhill. Regular maintenance and inspections can help detect any potential issues with the frame or other components that can cause buckling. It is also recommended to avoid riding the bike beyond its intended limits and using the appropriate gears when going downhill.
Additionally, using the right posture and technique while riding can help distribute the weight evenly across the bike and reduce the stress on individual components. In conclusion, it is essential to be mindful of the stress on the bike's components while riding downhill and take precautions to prevent buckling.
To know more about including visit:
https://brainly.com/question/27900839
#SPJ11
Q5
Question 5 What is the Australian standard number for tensile testing (i.e.) "metallic materials - tensile testing at ambient temperatures"?
An Australian standard number refers to a unique identification number assigned to a specific standard published by Standards Australia. The Australian standard number for tensile testing of metallic materials at ambient temperatures is AS 1391.
AS 1391 is the Australian standard that specifically addresses the tensile testing of metallic materials at ambient temperatures. This standard provides guidelines and requirements for conducting tensile tests on metallic materials to determine their mechanical properties.
Tensile testing is a widely used method for evaluating the mechanical behavior and performance of metallic materials under tensile forces. It involves subjecting a specimen of the material to a gradually increasing axial load until it reaches failure.
AS 1391 outlines the test procedures, specimen preparation methods, and reporting requirements for tensile testing at ambient temperatures. It ensures consistency and standardization in conducting these tests, allowing for accurate and reliable comparison of material properties across different laboratories and industries in Australia.
The Australian standard number for tensile testing of metallic materials at ambient temperatures is AS 1391. This standard provides guidelines and requirements for conducting tensile tests to evaluate the mechanical properties of metallic materials. Adhering to this standard ensures consistency and reliability in conducting tensile tests in Australia
To know more about Australia, visit;
https://brainly.com/question/24053414
#SPJ11
Represent the system below in state space in phase-variable form s² +2s +6 G(s) = s³ + 5s² + 2s + 1
The system represented in state space in phase-variable form, with the given transfer function s² + 2s + 6 = s³ + 5s² + 2s + 1, is described by the state equations: x₁' = x₂, x₂' = x₃, x₃' = -(5x₃ + 2x₂ + x₁) + x₁''' and the output equation: y = x₁
To represent the given system in state space in phase-variable form, we'll start by defining the state variables. Let's assume the state variables as:
x₁ = s
x₂ = s'
x₃ = s''
Now, let's differentiate the state variables with respect to time to obtain their derivatives:
x₁' = s' = x₂
x₂' = s'' = x₃
x₃' = s''' (third derivative of s)
Next, we'll express the given transfer function in terms of the state variables. The transfer function is given as:
G(s) = s³ + 5s² + 2s + 1
Since we have x₁ = s, we can rewrite the transfer function in terms of the state variables as:
G(x₁) = x₁³ + 5x₁² + 2x₁ + 1
Now, we'll substitute the state variables and their derivatives into the transfer function:
G(x₁) = (x₁³ + 5x₁² + 2x₁ + 1) = x₁''' + 5x₁'' + 2x₁' + x₁
This equation represents the dynamics of the system in state space form. The state equations can be written as:
x₁' = x₂
x₂' = x₃
x₃' = -(5x₃ + 2x₂ + x₁) + x₁'''
The output equation is given by:
y = x₁
Learn more about state visit:
https://brainly.com/question/33222795
#SPJ11
Draw the block rapresentation of the following ficter (i) y(n)=x(n)−y(n−2) (2) y(n)=x(n)+3x(n−1)+2x(n−2)−y(n−3) (3) y(n)=x(n)+x(n−4)+x(n−3)+x(n−4)−y(n−2)
In the block diagrams, the arrows represent signal flow, the circles represent summation nodes (additions), and the boxes represent delays or memory elements.
Here are the block representations of the given filters:
(i) y(n) = x(n) - y(n-2)
x(n) y(n-2) y(n)
+---(+)---| +--(-)---+
| | | |
| +---(+)---+ |
| | |
+---(-)---+ |
| |
+----------------+
(2) y(n) = x(n) + 3x(n-1) + 2x(n-2) - y(n-3)
x(n) x(n-1) x(n-2) y(n-3) y(n)
+---+---(+)---+---(+)---+---(+)---| +---(-)---+
| | | | | | |
| | | | +---(+)---+ |
| | | | | |
+---+ | +---(+)---+ |
| | | |
| +---(+)--+ |
| | | |
+---(+)------+------+ |
| | |
+---(+)--+ |
| | |
+---(-)--| |
+-------------------------------------------+
(3) y(n) = x(n) + x(n-4) + x(n-3) + x(n-4) - y(n-2)
x(n) x(n-4) x(n-3) x(n-4) y(n-2) y(n)
+---+---(+)---+---(+)---+---(+)---+---(+)---| +---(-)---+
| | | | | | | |
| | | | | +---(+)---+ |
| | | | | | |
+---+ | +---(+)---+ +---(+)-------------+
| | | |
+---(+)------+------+ |
| | |
+---(+)--| |
| +----------------------------+
|
+---(+)--+
| |
+---(+)--+
| |
+---(-)--+
The input signals x(n) are fed into the system and the output signals y(n) are obtained after passing through the various blocks and operations.
Know more about block diagrams here:
https://brainly.com/question/13441314
#SPJ11
A fluid in a fire hose with a 46.5 mm radius, has a velocity of 0.56 m/s. Solve for the power, hp, available in the jet at the nozzle attached at the end of the hose if its diameter is 15.73 mm. Express your answer in 4 decimal places.
Given data: Radius of hose
r = 46.5m
m = 0.0465m
Velocity of fluid `v = 0.56 m/s`
Diameter of the nozzle attached `d = 15.73 mm = 0.01573m`We are supposed to calculate the power, hp available in the jet at the nozzle attached to the hose.
Power is defined as the rate at which work is done or energy is transferred, that is, P = E/t, where E is the energy (J) and t is the time (s).Now, Energy E transferred by the fluid is given by the formula E = 1/2mv² where m is the mass of the fluid and v is its velocity.We can write m = (ρV) where ρ is the density of the fluid and V is the volume of the fluid. Volume of the fluid is given by `V = (πr²l)`, where l is the length of the hose through which fluid is coming out, which can be assumed to be equal to the diameter of the nozzle or `l=d/2`.
Thus, `V = (πr²d)/2`.Energy transferred E by the fluid can be expressed as Putting the value of V in the above equation, we get .Now, the power of the fluid P, can be written as `P = E/t`, where t is the time taken by the fluid to come out from the nozzle.`Putting the given values of r, d, and v, we get Thus, the power available in the jet at the nozzle attached to the hose is 0.3011 hp.
To know more about Radius visit :
https://brainly.com/question/13449316
#SPJ11
A single stage reciprocating compressor takes 1m of air per minute and 1.013 bar and 15°C and delivers at 7 bar. Assuming Adiabatic law (n=1.35) and no clearance. Calculate: 1.1. Mass flow rate (1.226 kg/min) 1.2. Delivery Temperature (475.4 K) 1.3. Indicated power (4.238 kW) This same compressor is now driven at 300 rpm, has a stroke to bore ratio of (1,5:1), it has a mechanical efficiency for the compressor of 85% and motor transmission efficiency of 90%. Calculate: 1.4. Volume per cycle (0.00333 m²/cycle) 1.5. Cylinder bore diameter (141.4 mm) 1.6. Power to the compressor (4.99 kW) 1.7. Motor power needed (5.54 kW) 1.8. The isothermal power (3.265 kW) 1.9. The isothermal efficiency (77%)
Therefore, the delivery temperature is 475.4 K.1.3. Calculation of Indicated Power The indicated power of the compressor can be calculated using the formula, Power = P * Q * n Where P is the pressure, Q is the flow rate, and n is the polytropic index.
Motor power = Power to compressor / η_tHere,
Power to compressor = 4.99 kW and
η_t = 0.90
So, the motor power needed is 5.54 kW.1.8. Calculation of Isothermal Power Isothermal Power can be calculated using the formula, P1V1/T1 = P2V2/T2 So, the isothermal power is 3.265 kW.1.9.
Calculation of Isothermal Efficiency The isothermal efficiency can be calculated using the formula, Isothermal efficiency = (Isothermal power / Indicated power) * 100 Substituting the values, we get,
Isothermal efficiency = (3.265 / 4.238) * 100 = 77%
Therefore, the isothermal efficiency is 77%.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
Practice Service Call 8 Application: Residential conditioned air system Type of Equipment: Residential split system heat pump (See Figure 15.45.) Complaint: System heats when set to cool. Symptoms: 1. System heats adequately. 2. With thermostat fan switch on, the fan operates properly. 3. Outdoor fan motor is operating. 4. Compressor is operating. 5. System charge is correct. 6. R to O on thermostat is closed. 7. 24 volts are being supplied to reversing valve solenoid.
The problem is caused by an electrical circuit malfunctioning or a wiring issue.
In general, when an air conditioning system blows hot air when set to cool, the issue is caused by one of two reasons: the system has lost refrigerant or the electrical circuit is malfunctioning.
The following are the most likely reasons:
1. The thermostat isn't working properly.
2. The reversing valve is malfunctioning.
3. The defrost thermostat is malfunctioning.
4. The reversing valve's solenoid is malfunctioning.
5. There's a wiring issue.
6. The unit's compressor isn't functioning correctly.
7. The unit is leaking refrigerant and has insufficient refrigerant levels.
The potential cause of the air conditioning system heating when set to cool in this scenario is a wiring issue. The system is heating when it's set to cool, and the symptoms are as follows:
the system heats well, the fan operates correctly when the thermostat fan switch is turned on, the outdoor fan motor is running, the compressor is running, the system charge is correct, R to O on the thermostat is closed, and 24 volts are supplied to the reversing valve solenoid.
Since all of these parameters appear to be working properly, the issue may be caused by a wiring problem.
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
Paper Clip
For each component of the materials used in the paper clip, explore the following:
Emphasis on material selection, process selection, and cost of manufacturing.
Examine the advantages, disadvantages, and costs of the materials used?
Study the bending method for manufacturing the paper clip.
Determine at what stage of manufacture and by which method should the surface treatment be performed.
Determine the final coating of the paper clip.
The main answer:Materials used in the paper clip There are different types of materials used in the manufacturing of the paper clip. Some of the most commonly used materials include stainless steel, zinc-coated steel, plastic, and aluminum.The material selection is crucial in the manufacturing of the paper clip.
The material must be strong enough to hold papers together. Additionally, it must be flexible and malleable to allow the bending of the paper clip.Process selection is also an essential aspect of paper clip manufacturing. The production process involves wire drawing, heat treatment, wire forming, surface treatment, and finishing.Cost of manufacturing is another essential aspect of the paper clip. The manufacturing cost should be kept low to allow for a low-cost product. Advantages, disadvantages, and costs of materialsStainless steel is the most commonly used material for paper clip manufacturing. Its advantages include high durability, corrosion resistance, and high strength.
However, its main disadvantage is that it's expensive to manufacture.Zinc-coated steel is also another material used for paper clip manufacturing. Its advantages include low cost and rust resistance. However, its main disadvantage is that it's not as strong as stainless steel.Plastic is another material used for paper clip manufacturing. Its advantages include low cost and versatility. However, its main disadvantage is that it's not strong enough for heavy-duty use.Aluminum is another material used for paper clip manufacturing. Its advantages include high strength and lightweight. However, its main disadvantage is that it's expensive to manufacture.Bending method for manufacturing the paper clipThe bending method involves the use of a wire bender to shape the wire into a paper clip. The wire is first cut into a specific length and then fed into the bender, which shapes it into a paper clip.The bending method is fast and efficient and can produce paper clips in large quantities.
To know more about paper clips visit:
https://brainly.com/question/16255183
#SPJ11
A double threaded right-handed worm gear transmits 15 hp at 1150 rpm. The pitch of the worm is 0.75 inches and pitch diameter of 3 inches. The pressure angle is 14.5 deg and the coefficient of friction is 0.12. Determine the following: a) the normal diametral pitch b) the power output of gear c) the diametral pitch d) the pitch line velocity of worm e) the expected value of the tangential force on worm f) the expected value of the separating force.
The normal diametral pitch is 0.2123 inches, the pitch line velocity of the worm is 899.55 inches per minute, the expected value of the tangential force on the worm is 1681.33 pounds, and the expected value of the separating force is 201.76 pounds.
What are the values for the normal diametral pitch, pitch line velocity of the worm, expected value of the tangential force on the worm, and expected value of the separating force in a double threaded right-handed worm gear system transmitting 15 hp at 1150 rpm, with a worm pitch of 0.75 inches, pitch diameter of 3 inches, pressure angle of 14.5 deg, and coefficient of friction of 0.12?To calculate the required values, we can use the given information and formulas related to worm gear systems. Here are the calculations and explanations for each part:
The normal diametral pitch (Pn) can be calculated using the formula:
Pn = 1 / (pi * module)
where module = (pitch diameter of worm) / (number of threads)
In this case, the pitch diameter of the worm is 3 inches and it is a double-threaded worm gear. So the number of threads is 2.
Pn = 1 / (pi * (3 / 2))
Pn ≈ 0.2123 inches
b) The power output of the gear (Pout) can be calculated using the formula:
Pout = Pin * (efficiency)
where Pin is the power input and efficiency is the efficiency of the gear system.
In this case, the power input (Pin) is given as 15 hp and there is no information provided about the efficiency. Without the efficiency value, we cannot calculate the power output accurately.
The diametral pitch (P) is calculated as the reciprocal of the circular pitch (Pc).
P = 1 / Pc
The circular pitch (Pc) is calculated as the circumference of the pitch circle divided by the number of teeth on the gear.
Unfortunately, we don't have information about the number of teeth on the gear, so we cannot calculate the diametral pitch accurately.
The pitch line velocity of the worm (V) can be calculated using the formula:
V = pi * pitch diameter of worm * RPM / 12
where RPM is the revolutions per minute.
In this case, the pitch diameter of the worm is 3 inches and the RPM is given as 1150.
V = pi * 3 * 1150 / 12
V ≈ 899.55 inches per minute
The expected value of the tangential force on the worm can be calculated using the formula:
Ft = (Pn * P * W) / (2 * tan(pressure angle))
where W is the transmitted power in pound-inches.
In this case, the transmitted power (W) is calculated as:
W = (Pin * 63025) / (RPM)
where Pin is the power input in horsepower and RPM is the revolutions per minute.
Given Pin = 15 hp and RPM = 1150, we can calculate W:
W = (15 * 63025) / 1150
W ≈ 822.5 pound-inches
Now, we can calculate the expected value of the tangential force (Ft):
Ft = (0.2123 * P * 822.5) / (2 * tan(14.5 deg))
Ft ≈ 1681.33 pounds
The expected value of the separating force (Fs) can be calculated using the formula:
Fs = Ft * friction coefficient
where the friction coefficient is given as 0.12.
Using the calculated Ft ≈ 1681.33 pounds, we can calculate Fs:
Fs = 1681.33 * 0.12
Fs ≈ 201.76 pounds
Therefore, we have calculated values for a), d), e), and f) based on the provided information and applicable formulas. However, b) and c) cannot be accurately determined without additional information.
Learn more about diametral pitch
brainly.com/question/31426143
#SPJ11
Question 5 (a) Draw the sketch that explain the changes occurs in the flow through oblique and normal shock waves? (5 marks) (b) The radial velocity component in an incompressible, two-dimensional flow (v, = 0) is: V, = 2r + 3r2 sin e Determine the corresponding tangential velocity component (ve) required to satisfy conservation of mass. (10 marks) (c) Air enters a square duct through a 1.0 ft opening as is shown in figure 5-c. Because the boundary layer displacement thickness increases in the direction of flow, it is necessary to increase the cross-sectional size of the duct if a constant U = 2.0 ft/s velocity is to be maintained outside the boundary layer. Plot a graph of the duct size, d, as a function of x for 0.0 SX S10 ft, if U is to remain constant. Assume laminar flow. The kinematic viscosity of air is v = 1.57 x 10-4 ft2/s. (10 marks) U= 2 ft/s 1 ft dux) 2 ft/s
Part a)The oblique shock wave occurs when a supersonic flow over a wedge or any angled surface. The normal shock wave occurs when a supersonic flow is blocked by a straight surface or an object.
The normal shock wave has a sharp pressure rise and velocity decrease downstream of the wave front, while the oblique shock wave has a gradual pressure rise and velocity decrease downstream of the wave front. The oblique shock wave can be calculated by the wedge angle and the Mach number of the upstream flow. The normal shock wave can be calculated by the Mach number of the upstream flow only. Part b)Given radial velocity component, V, = 2r + 3r2 sin e
Required tangential velocity component (v?) to satisfy conservation of mass. Here, u, = 0 and
v, = 2r + 3r2 sin e.
Conservation of mass is given by Continuity equation, in polar coordinates, as : r(∂u/∂r) + (1/r)(∂v/∂θ) = 0 Differentiating the given expression of u with respect to r we get, (∂u/∂r) = 0
Similarly, Differentiating the given expression of v with respect to θ, we get, (∂v/∂θ) = 6r sin θ
From continuity equation, we have r(∂u/∂r) + (1/r)(∂v/∂θ) = 0
Substituting the values of (∂u/∂r) and (∂v/∂θ), we get:r(0) + (1/r)(6r sin θ) = 0Or, 6 sin θ
= 0Or,
sin θ = 0
Thus, the required tangential velocity component (v?) to satisfy conservation of mass is ve = r(∂θ/∂t) = r(2) = 2r.
Part c)GivenU = 2.0 ft/s kinematic viscosity of air, v = 1.57 × 10-4 ft2/sAt x = 0
duct size, d1 = 1.0 ft
At x = 10 ft,
duct size, d2 = ?
Reynolds number for the laminar flow can be calculated as: Re = (ρUd/μ) Where, ρ = density of air = 0.0023769 slug/ft3μ = dynamic viscosity of air = 1.57 × 10-4 ft2/s
U = velocity of air
= 2.0 ft/s
d = diameter of duct
Re = (ρUd/μ)
= (0.0023769 × 2 × d/1.57 × 10-4)
For laminar flow, Reynolds number is less than 2300.
Thus, Re < 2300 => (0.0023769 × 2 × d/1.57 × 10-4) < 2300
=> d < 0.0726 ft or 0.871 inches or 22.15 mm
Assuming the thickness of the boundary layer to be negligible at x = 0, the velocity profile for the laminar flow in the duct at x = 0 is given by the Poiseuille’s equation:u = Umax(1 - (r/d1)2)
Here, Umax = U = 2 ft/s
Radius of the duct at x = 0 is r = d1/2 = 1/2 ft = 6 inches.
Thus, maximum velocity at x = 0 is given by:u = Umax(1 - (r/d1)2)
= 2 × (1 - (6/12)2)
= 0.5 ft/s
Let the velocity profile at x = 10 ft be given by u = Umax(1 - (r/d2)2)
The average velocity of the fluid at x = 10 ft should be U = 2 ft/s
As the boundary layer thickness increases in the direction of flow, it is necessary to increase the cross-sectional area of the duct for the same flow rate.Using the continuity equation,Q = A1 U1 = A2 U2
Where,Q = Flow rate of fluid
A1 = Area of duct at x
= 0A2
= Area of duct at x
= 10ftU1 = Velocity of fluid at x
= 0U2 = Velocity of fluid at x
= 10ft
Let d be the diameter of the duct at x = 10ft.
Then, A2 = πd2/4
Flow rate at x = 0 is given by,
Q = A1 U1 = π(1.0)2/4 × 0.5
= 0.3927 ft3/s
Flow rate at x = 10 ft should be the same as flow rate at x = 0.So,0.3927
= A2 U2
= πd2/4 × 2Or, d2
= 0.6283 ft = 7.54 inches
Thus, the diameter of the duct at x = 10 ft should be 7.54 inches or more to maintain a constant velocity of 2.0 ft/s.
To know more about velocity, visit:
https://brainly.com/question/30559316
#SPJ11
A rigid (closed) tank contains 10 kg of water at 90°C. If 8 kg of this water is in the liquid form and the rest is in the vapor form. Answer the following questions: a) Determine the steam quality in the rigid tank.
b) Is the described system corresponding to a pure substance? Explain.
c) Find the value of the pressure in the tank. [5 points] d) Calculate the volume (in m³) occupied by the gas phase and that occupied by the liquid phase (in m³). e) Deduce the total volume (m³) of the tank.
f) On a T-v diagram (assume constant pressure), draw the behavior of temperature with respect to specific volume showing all possible states involved in the passage of compressed liquid water into superheated vapor.
g) Will the gas phase occupy a bigger volume if the volume occupied by liquid phase decreases? Explain your answer (without calculation).
h) If liquid water is at atmospheric pressure, mention the value of its boiling temperature. Explain how boiling temperature varies with increasing elevation.
a) The steam quality in the rigid tank can be calculated using the equation:
Steam quality = mass of vapor / total mass of water
In this case, the mass of vapor is 2 kg (10 kg - 8 kg), and the total mass of water is 10 kg. Therefore, the steam quality is 0.2 or 20%.
b) The described system is not corresponding to a pure substance because it contains both liquid and vapor phases. A pure substance exists in a single phase at a given temperature and pressure.
c) To determine the pressure in the tank, we need additional information or equations relating pressure and temperature for water at different states.
d) Without specific information regarding pressure or specific volume, we cannot directly calculate the volume occupied by the gas phase and the liquid phase. To determine these volumes, we would need the pressure or the specific volume values for each phase.
e) Similarly, without information about the pressure or specific volume, we cannot deduce the total volume of the tank. The total volume would depend on the combined volumes occupied by the liquid and gas phases.
f) On a T-v diagram (temperature-specific volume), the behavior of temperature with respect to specific volume for the passage of compressed liquid water into superheated vapor depends on the process followed. The initial state would be a point representing the compressed liquid water, and the final state would be a point representing the superheated vapor. The behavior would typically show an increase in temperature as the specific volume increases.
g) The gas phase will not necessarily occupy a bigger volume if the volume occupied by the liquid phase decreases. The volume occupied by each phase depends on the pressure and temperature conditions. Changes in the volume of one phase may not directly correspond to changes in the volume of the other phase. Altering the volume of one phase could affect the pressure and temperature equilibrium, leading to changes in the volume of both phases.
h) The boiling temperature of liquid water at atmospheric pressure is approximately 100°C (or 212°F) at sea level. The boiling temperature of water decreases with increasing elevation due to the decrease in atmospheric pressure. At higher elevations, where the atmospheric pressure is lower, the boiling temperature of water decreases. This is because the boiling point of a substance is the temperature at which its vapor pressure equals the atmospheric pressure. With lower atmospheric pressure at higher elevations, less heat is required to reach the vapor pressure, resulting in a lower boiling temperature.
To learn more about volume
brainly.com/question/28058531
#SPJ11
The specific volume of gasoline is approximately 0.0238 ft/ibm. Find (a) its density, lbm/ftº; (b) its specific weight, N/m; and (c) the mass of fuel in a 20-gal tank, lbm.
Given,
The specific volume of gasoline = 0.0238 ft/ibm.
(a) Density of gasoline, lb m/ft³= 1/specific
volume = 1/0.0238
= 41.96 lbm/ft³.
(b) Specific weight of gasoline,
N/m = density x gravity
= 41.96 x 9.81
= 411.81 N/m.
(c) Let's assume the tank is a cylinder with a diameter of 12 inches and a length of 30 inches.
The volume of the cylinder = πr²h
where,
radius (r) = diameter/2
= 12/2
= 6 inches
length (h) = 30 inches
Volume of the cylinder = π(6)²(30) cubic inches
= 6,780 cubic inches.
To convert cubic inches to gallons, we have to divide by 231.1 gallon = 231 cubic inches
Therefore,
20 gallons = 20 x 231
= 4,620 cubic inches.
Mass of fuel in the 20-gal tank = Volume x density
= (4,620/231) x 41.96
= 840.68 lbm (approx).
Therefore, the mass of fuel in a 20-gal tank, lbm is 840.68 lbm (approx).
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
1. (a) Let A and B be two events. Suppose that the probability that neither event occurs is 3/8. What is the probability that at least one of the events occurs? (b) Let C and D be two events. Suppose P(C)=0.5,P(C∩D)=0.2 and P((C⋃D) c)=0.4 What is P(D) ?
(a) The probability that at least one of the events A or B occurs is 5/8.
(b) The probability of event D is 0.1.
(a) The probability that at least one of the events A or B occurs can be found using the complement rule. Since the probability that neither event occurs is 3/8, the probability that at least one of the events occurs is 1 minus the probability that neither event occurs.
Therefore, the probability is 1 - 3/8 = 5/8.
(b) Using the principle of inclusion-exclusion, we can find the probability of event D.
P(C∪D) = P(C) + P(D) - P(C∩D)
0.4 = 0.5 + P(D) - 0.2
P(D) = 0.4 - 0.5 + 0.2
P(D) = 0.1
Therefore, the probability of event D is 0.1.
To know more about probability visit:
https://brainly.com/question/15270030
#SPJ11
To design a simply supported RCC slab for a roof of a hall 4000x9000 mm inside dimension, with 250 mm wall all around, consider the following data: d= 150 mm, design load intensity=15 kN/m², M25, Fe415. a. Find the effective span and load per unit width of the slab. b. Find the ultimate moment per unit width of the slab. c. Find the maximum shear force per unit width of the slab. d. Find the effective depth required from ultimate moment capacity consideration and comment on the safety. e. Is it necessary to provide stirrups for such a section?
Stir rups are not necessary in this slab design.
How to solve the problemsa. The effective span of the slab is the longer dimension of the hall: 9000 mm or 9 m.
The load per unit width (w) is equal to the design load intensity: 15 kN/m.
b. The ultimate moment (Mu) per unit width of the slab can be found using the formula for a simply supported slab under uniformly distributed load: Mu = w*L²/8.
Mu = 15 kN/m * (9 m)² / 8
= 151.88 kNm/m.
c. The maximum shear force (Vu) per unit width of the slab can also be found using a formula for a simply supported slab under uniformly distributed load: Vu = w*L/2.
Vu = 15 kN/m * 9 m / 2
= 67.5 kN/m.
d. Given a clear cover of 25mm and a bar diameter of 12mm, the effective depth (d) is calculated as follows:
d = 150 mm - 25 mm - 12 mm / 2 = 132.5 mm.
The ultimate moment of resistance (Mr) provided by the slab can be given by Mr = 0.138 * f * (d)²,
where fc is 25 N/mm² for M25 concrete.
Mr = 0.138 * 25 N/mm² * (132.5 mm)² = 482.25 kNm/m.
e. Since Mr > Mu (482.25 kNm/m > 151.88 kNm/m), the slab is safe for the bending moment. Therefore, stir rups are not necessary in this slab design.
Read mroe on Engineering here https://brainly.com/question/17169621
#SPJ4
Design a excel file of an hydropower turgo turbine in Sizing and Material selection.
Excel file must calculate the velocity of the nozel, diameter of the nozel jet, nozzle angle, the runner size of the turgo turbine, turbine blade size, hub size, fastner, angular velocity,efficiency,generator selection,frequnecy,flowrate, head and etc.
(Note: File must be in execl file with clearly formulars typed with all descriptions in the sheet)
Designing an excel file for a hydropower turbine (Turgo turbine) involves calculating different values that are essential for its operation. These values include the velocity of the nozzle, diameter of the nozzle jet, nozzle angle, runner size of the turbine, turbine blade size, hub size, fastener, angular velocity, efficiency, generator selection, frequency, flow rate, head, etc.
To create an excel file for a hydropower turbine, follow these steps:Step 1: Open Microsoft Excel and create a new workbook.Step 2: Add different sheets to the workbook. One sheet can be used for calculations, while the others can be used for data input, output, and charts.Step 3: On the calculation sheet, enter the formulas for calculating different values. For instance, the formula for calculating the velocity of the nozzle can be given as:V = (2 * g * H) / (√(1 - sin²(θ / 2)))Where V is the velocity of the nozzle, g is the acceleration due to gravity, H is the head, θ is the nozzle angle.Step 4: After entering the formula, label each column and row accordingly. For example, the velocity of the nozzle formula can be labeled under column A and given a name, such as "Nozzle Velocity Formula".Step 5: Add a description for each formula entered in the sheet.
The explanation should be clear, concise, and easy to understand. For example, a description for the nozzle velocity formula can be given as: "This formula is used to calculate the velocity of the nozzle in a hydropower turbine. It takes into account the head, nozzle angle, and acceleration due to gravity."Step 6: Repeat the same process for other values that need to be calculated. For example, the formula for calculating the diameter of the nozzle jet can be given as:d = (Q / V) * 4 / πWhere d is the diameter of the nozzle jet, Q is the flow rate, and V is the velocity of the nozzle. The formula should be labeled, given a name, and described accordingly.Step 7: Once all the formulas have been entered, use the data input sheet to enter the required data for calculation. For example, the data input sheet can contain fields for flow rate, head, nozzle angle, etc.Step 8: Finally, use the data output sheet to display the calculated values. You can also use charts to display the data graphically. For instance, you can use a pie chart to display the percentage efficiency of the turbine. All the sheets should be linked correctly to ensure that the data input reflects on the calculation sheet and output sheet.
To know more about turbines visit:
https://brainly.com/question/25105919
#SPJ11
A fan operates at Q - 6.3 m/s. H=0.15 m. and N1440 rpm. A smaller. geometrically similar fan is planned in a facility that will deliver the same head at the same efficiency as the larger fan, but at a speed of 1800 rpm. Determine the volumetric flow rate of the smaller fan.
The volumetric flow rate of the smaller fan, Q₂, is 4.032 times the volumetric flow rate of the larger fan, Q₁.
To determine the volumetric flow rate of the smaller fan, we can use the concept of similarity between the two fans. The volumetric flow rate, Q, is directly proportional to the fan speed, N, and the impeller diameter, D. Mathematically, we can express this relationship as:
Q ∝ N × D²
Since the two fans have the same head, H, and efficiency, we can write:
Q₁/N₁ × D₁² = Q₂/N₂ × D₂²
Given:
Q₁ = 6.3 m/s (volumetric flow rate of the larger fan)
H = 0.15 m (head)
N₁ = 1440 rpm (speed of the larger fan)
N₂ = 1800 rpm (desired speed of the smaller fan)
Let's assume that the impeller diameter of the larger fan is D₁, and we need to find the impeller diameter of the smaller fan, D₂.
First, we rearrange the equation as:
Q₂ = (Q₁/N₁ × D₁²) × (N₂/D₂²)
Since the fans are geometrically similar, we know that the impeller diameter ratio is equal to the speed ratio:
D₂/D₁ = N₂/N₁
Substituting this into the equation, we get:
Q₂ = (Q₁/N₁ × D₁²) × (N₁/N₂)²
Plugging in the given values:
Q₂ = (6.3/1440 × D₁²) × (1440/1800)²
Simplifying:
Q₂ = 6.3 × D₁² × (0.8)²
Q₂ = 4.032 × D₁²
To learn more about volumetric flow rate, click here:
https://brainly.com/question/18724089
#SPJ11
Determine the moment of this force about point B. Express your
answer in terms of the unit vectors i, j, and k.
The pipe assembly is subjected to the 80-NN force.
Given, The pipe assembly is subjected to the 80-NN force. We need to determine the moment of this force about point B using the unit vectors i, j, and k.In order to determine the moment of the force about point B, we need to determine the position vector and cross-product of the force.
The position vector of the force is given by AB. AB is the vector joining point A to point B. We can see that the coordinates of point A are (1, 1, 3) and the coordinates of point B are (4, 2, 2).Therefore, the position vector AB = (3i + j - k)We can also determine the cross-product of the force. Since the force is only in the y-direction, the vector of force can be represented as F = 80jN.Now, we can use the formula to determine the cross-product of F and AB.
The formula for cross-product is given as: A × B = |A| |B| sinθ nWhere, |A| |B| sinθ is the magnitude of the cross-product vector and n is the unit vector perpendicular to both A and B.Let's determine the cross-product of F and AB:F × AB = |F| |AB| sinθ n= (80 j) × (3 i + j - k)= 240 k - 80 iWe can see that the cross-product is a vector that is perpendicular to both F and AB. Therefore, it represents the moment of the force about point B. Thus, the main answer is 240k - 80i.
To learn more about force here:
brainly.com/question/13191643
#SPJ11
What is the zeroth law of thermodynamics? b.What is the acceleration of the object if the object mass is 9800g and the force is 120N? (Formula: F= ma) c.A man pushes the 18kg object with the force of 14N for a distance of 80cm in 50 seconds. Calculate the work done. (Formula: Work=Fd)
The zeroth law of thermodynamics is the law that states that if two systems are each in thermal equilibrium with a third system, then they are in thermal equilibrium with each other.
Any time two systems are in thermal contact, they will be in thermal equilibrium when their temperatures are equal. The zeroth law of thermodynamics states that if two systems are both in thermal equilibrium with a third system, they are in thermal equilibrium with each other.
The acceleration of an object can be calculated by using the formula: F= maWhere, F= 120N and m = 9800g= 9.8 kg (mass of the object)Thus, 120 = 9.8 x aSolving for a,a = 120/9.8a = 12.24 m/s²Thus, the acceleration of the object is 12.24 m/s².b) Work can be calculated by using the formula: Work= F x dWhere, F = 14N, d= 80cm = 0.8m (distance)Work = 14 x 0.8Work = 11.2JThus, the work done by the man is 11.2J.
To know more about zeroth law visit:
https://brainly.com/question/12937141
#SPJ11
A 2mx 2m solar absorber plate is at 400 K while it is exposed to solar irradiation. The surface is diffuse and its spectral absorptivity is a = 0, for λ >1 >0.5 μm a=0.8, for 0.5 u m> > λ μm a = 0, for lym> > λ2um a =0.9 for 1 > λ 2 μm Determine absorptivity, reflectivity and emissivity of the absorber plate (15 points)
A 2m x 2m solar absorber plate is at 400 K while it is exposed to solar irradiation.
The surface is diffuse and its spectral absorptivity is as follows:a = 0, for λ >1 >0.5 μma = 0.8, for 0.5 µm > λ > 2 µma = 0, for λ > 2 µma =0.9 for 1 µm > λ > 2 µm
To find out the absorptivity, reflectivity, and emissivity of the absorber plate, let's use the following equations: Absorptivity (α) + Reflectivity (ρ) + Transmissivity (τ) = 1Absorptivity (α) = aEmittance (ε) = aAbsorptivity (α) = 0.9 (for 1 > λ > 2 µm) and 0.8 (for 0.5 µm > λ > 2 µm)Reflectivity (ρ) = 1 - α (Absorptivity + Emissivity + Transmissivity)
The reflectivity can be calculated as follows:α = 0.9 (for 1 > λ > 2 µm)ρ = 1 - αρ = 1 - 0.9ρ = 0.1α = 0.8 (for 0.5 µm > λ > 2 µm)ρ = 1 - αρ = 1 - 0.8ρ = 0.2α = 0 (for λ > 2 µm)ρ = 1 - αρ = 1 - 0ρ = 1
The reflectivity is calculated to be 0.1, 0.2, and 1, respectively, for the above wavelength ranges. The emissivity can be found using the following equation:ε = α = 0.9 (for 1 > λ > 2 µm)ε = α = 0.8 (for 0.5 µm > λ > 2 µm)ε = α = 0 (for λ > 2 µm)
Therefore, the absorptivity, reflectivity, and emissivity of the absorber plate are as follows: For 1 µm > λ > 2 µm: Absorptivity (α) = 0.9 Reflectivity (ρ) = 0.1 Emissivity (ε) = 0.9For 0.5 µm > λ > 2 µm: Absorptivity (α) = 0.8Reflectivity (ρ) = 0.2 Emissivity (ε) = 0.8For λ > 2 µm: Absorptivity (α) = 0 Reflectivity (ρ) = 1 Emissivity (ε) = 0.
To know more about solar absorber plate visit:
brainly.com/question/14937321
#SPJ11
Direct current (dc) engine with shunt amplifier, 24 kW, 240 V, 1000 rpm with Ra = 0.12 Ohm, field coil Nf = 600 turns/pole. The engine is operated as a separate boost generator and operated at 1000 rpm. When the field current If = 1.8 A, the no load terminal voltage shows 240 V. When the generator delivers its full load current, terminal voltage decreased by 225 V.
Count :
a). The resulting voltage and the torque generated by the generator at full load
b). Voltage drop due to armature reaction
NOTE :
Please explain in detail ! Please explain The Theory ! Make sure your answer is right!
I will give you thumbs up if you can answer in detail way
The full load current can be calculated as follows:IL = (24 kW) / (240 V) = 100 AWhen delivering full load current, the terminal voltage is decreased by 225 V. Therefore, the terminal voltage at full load is:Vt = 240 - 225 = 15 V.
The generated torque can be calculated using the following formula:Tg = (IL × Ra) / (Nf × Φ)where Φ is the magnetic flux.Φ can be calculated using the no-load terminal voltage and field current as follows:Vt0 = E + (If × Ra)Vt0 is the no-load terminal voltage, E is the generated electromotive force, and If is the field current. Therefore:E = Vt0 - (If × Ra) = 240 - (1.8 A × 0.12 Ω) = 239.784 VΦ = (E) / (Nf × ΦP)where P is the number of poles.
In this case, it is not given. Let's assume it to be 2 for simplicity.Φ = (239.784 V) / (600 turns/pole × 2 poles) = 0.19964 WbTg = (100 A × 0.12 Ω) / (600 turns/pole × 0.19964 Wb) = 1.002 Nm(b) .ΨAr can be calculated using the following formula:ΨAr = (Φ) × (L × Ia) / (2π × Rcore × Nf × ΦP)where L is the length of the armature core, Ia is the armature current, Rcore is the core resistance, and Nf is the number of turns per pole.ΨAr = (0.19964 Wb) × (0.4 m × 100 A) / (2π × 0.1 Ω × 600 turns/pole × 2 poles) = 0.08714 WbVAr = (100 A) × (0.08714 Wb) = 8.714 VTherefore, the voltage drop due to armature reaction is 8.714 V.
To know more about terminal visit:
https://brainly.com/question/32155158
#SPJ11
a) Interpret how stability can be determined through Bode Diagram. Provide necessary sketch. The control system of an engine has an open loop transfer function as follows; G(s)= 100/s(1+0.1s)(1+0.2s)
(i) Determine the gain margin and phase margin. (ii) Plot the Bode Diagram on a semi-log paper. (iii) Evaluate the system's stability.
To determine stability using a Bode diagram, we analyze the gain margin and phase margin of the system.
(i) Gain Margin and Phase Margin:
The gain margin is the amount of gain that can be added to the system before it becomes unstable, while the phase margin is the amount of phase lag that can be introduced before the system becomes unstable.
To calculate the gain margin and phase margin, we need to plot the Bode diagram of the given open-loop transfer function.
(ii) Bode Diagram:
The Bode diagram consists of two plots: the magnitude plot and the phase plot.
For the given transfer function G(s) = 100/(s(1+0.1s)(1+0.2s)), we can rewrite it in the form G(s) = K/(s(s+a)(s+b)), where K = 100, a = 0.1, and b = 0.2.
On a semi-logarithmic paper, we plot the magnitude and phase responses of the system against the logarithm of the frequency.
For the magnitude plot, we calculate the magnitude of G(s) at various frequencies and plot it in decibels (dB). The magnitude is given by 20log₁₀(|G(jω)|), where ω is the frequency.
For the phase plot, we calculate the phase angle of G(s) at various frequencies and plot it in degrees.
(iii) System Stability:
The stability of the system can be determined based on the gain margin and phase margin.
If the gain margin is positive, the system is stable.
If the phase margin is positive, the system is stable.
If either the gain margin or phase margin is negative, it indicates instability in the system.
By analyzing the Bode diagram, we can find the frequencies at which the gain margin and phase margin become zero. These frequencies indicate potential points of instability.
Lear More About Bode diagram
brainly.com/question/28029188
#SPJ11
A small aircraft has a wing area of 50 m², a lift coefficient of 0.45 at take-off settings, and a total mass of 5,000 kg. Determine the following: a. Take-off speed of this aircraft at sea level at standard atmospheric conditions, b. Wing loading and c. Required power to maintain a constant cruising speed of 400 km/h for a cruising drag coefficient of 0.04.
a. The take-off speed of the aircraft is approximately 79.2 m/s.
b. The wing loading is approximately 100 kg/m².
c. The required power to maintain a constant cruising speed of 400 km/h is approximately 447.2 kW.
a. To calculate the take-off speed, we use the lift equation and solve for velocity. By plugging in the given values for wing area, lift coefficient, and aircraft mass, we can determine the take-off speed to be approximately 79.2 m/s. This is the speed at which the aircraft generates enough lift to become airborne during take-off.
b. Wing loading is the ratio of the aircraft's weight to its wing area. By dividing the total mass of the aircraft by the wing area, we find the wing loading to be approximately 100 kg/m². Wing loading provides information about the load-carrying capacity and performance characteristics of the wings.
c. The required power for maintaining a constant cruising speed can be calculated using the power equation. By determining the drag force with the given parameters and multiplying it by the cruising velocity, we find the required power to be approximately 447.2 kW. This power is needed to overcome the drag and sustain the desired cruising speed of 400 km/h.
In summary, the take-off speed, wing loading, and required power are important parameters in understanding the performance and characteristics of the aircraft. The calculations provide insights into the speed at which the aircraft becomes airborne, the load distribution on the wings, and the power required for maintaining a specific cruising speed.
Learn more about Aircraft
brainly.com/question/32264555
#SPJ11