A cat runs at 0.5c. A flea runs toward the cat's head at 0.5 c. How fast is the flea moving relative to the ground? . approximately c .approximately 0.50 . approximately 1.5c .approximately 0.8c

Approximately 10-20 hp of added power is required when using a cartop carrier and driving at 100 km/h in a 25 km/h headwind, compared to not using the carrier in the same conditions.

The added power required when using a cartop carrier and driving at 100 km/h in a 25 km/h headwind is due to the increased drag on the car caused by the carrier and the wind. The exact amount of added power required will depend on the size and shape of the carrier, as well as the specific car and engine being used. However, estimates suggest that this added power could be in the range of 10-20 hp. It is important to note that using a cartop carrier can also impact the handling and stability of the car, so it is important to follow the manufacturer's instructions and drive with caution.

Learn more about required here:

https://brainly.com/question/4130932

#SPJ11

An  electric field strength that would store 17.5 J of energy in every 1.00 mm3 of space is 1.988 x 10^11 N/C.

To find the electric field strength that would store 17.5 J of energy in every 1.00 mm3 of space, we need to use the formula for electric potential energy:
U = (1/2) * ε * E^2 * V
where U is the potential energy, ε is the electric permittivity of the medium (in this case, vacuum), E is the electric field strength, and V is the volume of the space.

Rearranging the formula, we get:
E = √(2U/εV)
Plugging in the given values, we get:
E = √(2 * 17.5 J / (8.85 x 10^-12 C^2/N/m^2 * 1.00 x 10^-9 m^3))
Simplifying the expression inside the square root, we get:
E = √(3.954 x 10^21 N/C^2)
Taking the square root, we get:
E = 1.988 x 10^11 N/C
 

To know more energy  visit:-

https://brainly.com/question/1932868

#SPJ11

In a series circuit, the current flows through each component in a series, like a line of people waiting to pass through a narrow gate. As there is only one path for the current to flow through, the current must flow through each resistor to complete the circuit.

The total current in the circuit is equal to the current through each resistor. Therefore, the current through each resistor is the same, as they all experience the same "traffic" or resistance in the circuit. An analogy can be made with a hosepipe where the water flows through the hose in a series, and the diameter of the hose remains the same throughout the length.

In a parallel circuit, the current has multiple paths to flow through, like a group of people splitting into different lines at a fork in the road. Each resistor is connected to the same voltage source, and the voltage across each resistor is the same. As a result, the current through each resistor is determined by its resistance. The smaller the resistance of the resistor, the more current it will draw. An analogy can be made with a river splitting into several branches, each branch having its own flow rate and volume. Therefore, the total current in a parallel circuit is the sum of the current through each resistor.

Learn more about current here:

brainly.com/question/29027199

#SPJ11

Sunspots appear dark because they have lower temperatures compared to the surrounding areas on the Sun's surface. This cooler temperature is caused by intense magnetic activity that inhibits.

The flow of heat from the Sun's interior to the surface. As a result, the temperature within sunspots can be thousands of degrees cooler than the rest of the Sun's surface, which makes them appear darker. Sunspots are also associated with strong magnetic fields that can cause solar flares and other forms of space weather that can affect Earth. Scientists study sunspots to better understand the behavior of the Sun and how it impacts our planet. The study of sunspots is important for space weather prediction and for understanding the Sun's influence on our climate and atmosphere.

learn more about magnetic here:

https://brainly.com/question/2841288

#SPJ11

If two lamps on the black circuit burned out, the current in the neutral wire will be 2.33 amps.

The total power consumed by the lamps and motors on the black wire is (4200)+(1201)= 880 watts. The power consumed by the motor on the red wire is 240 watts, and the power consumed by the lamps and motors on the red wire is (3200)+(1.67240)+(120*1)= 1020.4 watts. The total power consumed by both circuits is 1900.4 watts.

Since the system is three-wire, the neutral wire carries only the unbalanced current. If two lamps on the black circuit burned out, the power consumed by the black circuit will be (2200)+(1201)= 520 watts. The power consumed by the red circuit remains the same, which is 1020.4 watts. The total power consumed by both circuits now becomes 1540.4 watts.

To find the current in the neutral wire, we can use the formula P=VI, where P is power, V is voltage and I is current. So, I=P/V. Therefore, the current in the neutral wire is (1900.4-1540.4)/120= 2.33 amps.

Learn more about current here:

brainly.com/question/17044230

#SPJ11

If the pressure is held constant, the volume of a gas is directly proportional to its temperature, according to Charles's law. When the Celsius temperature is doubled, the volume of the gas will also double. This relationship holds as long as the pressure remains constant.

In other words, if the temperature increases by a factor of two, the volume will also increase by a factor of two. This can be explained by considering that an increase in temperature causes the gas molecules to move faster and collide with each other and the container walls more frequently. As a result, the gas molecules exert a greater force on the container walls, leading to an expansion of the gas volume.

When the Celsius temperature is doubled while keeping the pressure constant, the volume of a gas will increase by a factor of two. This can be understood by considering the kinetic theory of gases. According to this theory, the average kinetic energy of gas molecules is directly proportional to the temperature. When the temperature doubles, the average kinetic energy of the gas molecules also doubles. The increased kinetic energy leads to more frequent and energetic collisions between the gas molecules, which results in a greater pressure exerted on the container walls. To maintain the pressure constant, the volume of the gas must increase to accommodate the increased molecular motion. Thus, the volume of the gas doubles when the Celsius temperature is doubled, provided that the pressure remains unchanged.

Learn more about  Charles's law  : brainly.com/question/14842720

#SPJ11

Answer:

0.0003Ωcm

Explanation:

The resistance of a wire = (the resistivity of the material × the length) ÷ the cross-sectional area (thickness)

R = ρl ÷ A

3.0Ω = (ρ x 150cm) ÷ 0.015 cm²

3.0Ω × 0.015 cm² = ρ x 150cm

(3.0Ω × 0.015 cm²) ÷ 150cm = ρ

ρ = 0.0003Ωcm

The value that is conserved in addition to electric charge, energy, and momentum in all three types of radioactive decay is the nucleon number.

The nucleon number is the total number of protons and neutrons in an atom's nucleus. During radioactive decay, the nucleus may undergo a change in its nucleon number by emitting or absorbing particles such as alpha particles, beta particles, or gamma rays. However, the total nucleon number before and after the decay remains the same, which is a fundamental principle of conservation in nuclear physics.

In all three types of radioactive decay, the value that is conserved in addition to electric charge, energy, and momentum is the nucleon number. The nucleon number represents the total number of protons and neutrons in a nucleus, and it remains constant throughout the decay process.

To  know more about electric charge visit:-

https://brainly.com/question/29736640

#SPJ11

When a light ray passes from water (with a refractive index of 1.333) into diamond (with a refractive index of 2.419) at an angle of 45 degrees, its path is affected by the change in refractive index. Refraction occurs when light passes from one medium to another with a different refractive index, causing the light to bend.

In this case, the light ray will bend towards the normal as it enters the diamond, due to the diamond's higher refractive index. This means that the angle of incidence will be smaller than the angle of refraction.

As the light ray passes through the diamond, it will continue to bend slightly, due to the difference in refractive index between the diamond and air. When the light ray exits the diamond and enters the air, it will bend away from the normal, as the refractive index of air is lower than that of the diamond.

Overall, the path of the light ray passing from water to diamond at an angle of 45 degrees will be curved due to the phenomenon of refraction, with the amount and direction of bending depending on the difference in refractive index between the two materials.

To know more about Refraction click this link-

https://brainly.com/question/13088981

#SPJ11

The frequency of the AC voltage applied to the capacitor can be calculated using the formula X = 1/(2πfC), where X is the reactance, f is the frequency, and C is the capacitance.

In an AC circuit, a capacitor acts as a frequency-dependent resistor, offering greater resistance to lower frequencies and smaller resistance to higher frequencies. The amount of resistance offered by the capacitor to the flow of current is called its reactance, which is given by the formula X = 1/(2πfC), where X is the reactance, f is the frequency, and C is the capacitance.

In this case, the reactance of the 95 mf capacitor is given as 0.65 ω. Substituting the given values in the formula, we get:

0.65 = 1/(2πf × 95 × 10^-6)

Solving for f, we get:

f = 1/(2π × 0.65 × 95 × 10^-6)

f ≈ 2.61 kHz

Therefore, the frequency of the AC voltage applied to the capacitor is approximately 2.61 kHz.

Learn more about capacitors here:- brainly.com/question/17176550

#SPJ11

The minimum distance between cars A and B is 107.4 miles.  

The minimum distance between cars A and B, we need to use some basic geometry. Let's assume that the two cars are currently on opposite sides of a straight line that connects their current positions. The distance between the two cars can be calculated using the Pythagorean theorem:

[tex]c^2 = a^2 + b^2[/tex]

here c is the distance between the two cars, a is the distance that car A needs to travel north, and b is the distance that car B needs to travel east.

We know that car A is currently 50 miles south of car B, and it is traveling north at a rate of 25 mph. To find the distance that car A needs to travel north to meet car B, we can use the Pythagorean theorem:

[tex]50^2 = 25^2 + 0^2[/tex]

2500 = 625 + 0

2500 = 625

2500 = 625 + 50

2500 = 675

So car A needs to travel 675 miles north to meet car B.

We also know that car B is currently 50 miles east of car A, and it is traveling west at a rate of 15 mph. To find the distance that car B needs to travel west to meet car A, we can use the Pythagorean theorem:

[tex]50^2 = 0^2 + 15^2[/tex]

500 = 0 + 225

500 = 225

So car B needs to travel 225 miles west to meet car A.

Finally, we can use the Pythagorean theorem again to find the minimum distance between the two cars:

[tex]c^2 = a^2 + b^2\\c^2 = 225^2 + 675^2[/tex]

c = [tex]\sqrt{(225^2 + 675^2)}[/tex]

c = [tex]\sqrt{(8025 + 4375)}[/tex]

c = [tex]\sqrt{12400}[/tex]

c = 107.4

Therefore, the minimum distance between cars A and B is 107.4 miles.  

Learn more about distance visit: brainly.com/question/28935294

#SPJ4

To solve this problem, we need to use the famous equation from Albert Einstein's theory of relativity: E=mc^2. This equation relates energy (E) to mass (m) and the speed of light (c).
First, we need to find the total mass of matter and antimatter in the fuel supply. Since the problem states that the total mass is 420 kg, we can assume that it is evenly divided between matter and antimatter, so each has a mass of 210 kg.
Next, we need to calculate the total energy released when this fuel supply is combined. We can use the equation E=mc^2, where E is the energy released, m is the total mass of the fuel supply, and c is the speed of light.
Plugging in the numbers, we get:
E = (210 kg + 210 kg) * (2.998 x 10^8 m/s)^2
E = 4.68 x 10^17 J
Therefore, the energy released when the Enterprise's antimatter fuel supply combines with matter is 4.68 x 10^17 joules.
To calculate the energy released when the 420 kg of antimatter combines with an equal amount of matter, we use Einstein's mass-energy equivalence formula:
E = mc^2
where E is the energy released, m is the total mass of matter and antimatter (2 x 420 kg = 840 kg), and c is the speed of light (2.998 x 10^8 meters per second).
E = (840 kg) * (2.998 x 10^8 m/s)^2
E ≈ 7.54 x 10^19 Joules
The energy released when the Enterprise's antimatter fuel supply combines with matter is approximately 7.54 x 10^19 Joules.

To know more about relativity visit :-

https://brainly.com/question/27802417

#SPJ11

you must be going at a speed of 7.37 m/s to land directly in the floating ring.

Using the formula for vertical displacement, we get:

Δy = v₀t + 1/2gt²

v₀x = Δx/t

Substituting the value of Δx, we get:

v₀x = 4 m / t

Now we can combine the two equations to solve for v₀:

-12 m = v₀y t + 1/2gt²

4 m = v₀x t

We can solve the second equation for t:

t = 4 m / v₀x

Substituting this value of t into the first equation, we get:

-12 m = v₀y (4 m / v₀x) + 1/2g(16 m² / v₀x²)

Simplifying, we get:

-24 m v₀x² = 16 v₀y² - 392

We want to solve for v₀, so we can rearrange this equation to get:

v₀ = √((392 + 24 m v₀x²) / 16)

Substituting the value we obtained for v₀x, we get:

v₀ = √((98 + 3 v₀²) / 4)

Solving for v₀, we get:

v₀ = 7.37 m/s

Speed is the rate at which an object changes its position in a given time interval. It is a scalar quantity that only refers to the magnitude of the velocity and not its direction. The standard unit of speed is meters per second (m/s) in the SI system. The formula for calculating speed is speed = distance / time. It describes how fast an object travels a certain distance in a given amount of time. Speed can also be calculated as the derivative of the position with respect to time.

Speed is a crucial concept in many areas of physics, including mechanics, kinematics, and thermodynamics. It is important in understanding how objects move, as well as how energy is transferred in various processes. For example, the speed of a projectile can determine the distance it travels and the impact it has on a target.

To learn more about Speed visit here:

brainly.com/question/28224010

#SPJ4

The total current in the circuit is approximately 6.84 A by using Ohm's Law and Kirchhoff's Current Law (KCL).

Ohm's Law states that the current through a resistor is proportional to the potential difference across it and inversely proportional to its resistance. Mathematically, we can express this as:

I = V/R

where I is the current through the resistor, V is the potential difference across the resistor, and R is the resistance of the resistor.

Kirchhoff's Current Law states that the sum of currents entering a junction is equal to the sum of currents leaving the junction. In other words, the total current flowing into a junction is equal to the total current flowing out of the junction. This law is based on the principle of conservation of charge.

Now, for the given circuit, we have four 7.0 Ω resistors connected in parallel. This means that the potential difference across each resistor is the same and equal to the applied potential difference of 12 V. The resistance of the combination can be calculated using the formula for the equivalent resistance of parallel resistors:

1/R_eq = 1/R1 + 1/R2 + 1/R3 + 1/R4

Substituting the given values, we get:

1/R_eq = 1/7.0 + 1/7.0 + 1/7.0 + 1/7.0 = 4/7.0

R_eq = 7.0/4 ≈ 1.75 Ω

Using Ohm's Law, the current through each resistor is:

I = V/R = 12 V/7.0 Ω ≈ 1.71 A

Since the resistors are connected in parallel, the total current in the circuit is the sum of the currents through each resistor:

I_total = I1 + I2 + I3 + I4 = 4I ≈ 6.84 A

Therefore, the total current in the circuit is approximately 6.84 A.

To know more about Ohm's Law, please click on:

https://brainly.com/question/1247379

#SPJ11

The given statement "force is equal to the change in linear momentum over the change in time." is True because this relationship is defined by Newton's Second Law of Motion, which states that the force acting on an object is equal to the rate of change of its linear momentum, given by the equation: Force (F) = Δ(mv) / Δt, where Δ(mv) represents the change in linear momentum and Δt represents the change in time.

Momentum is so important for understanding motion that it was called the quantity of motion by physicists such as Newton. Force influences momentum, and we can rearrange Newton’s second law of motion to show the relationship between force and momentum.

Recall our study of Newton’s second law of motion (Fnet = ma). Newton actually stated his second law of motion in terms of momentum: The net external force equals the change in momentum of a system divided by the time over which it changes. The change in momentum is the difference between the final and initial values of momentum.

So, Learn more about force at

https://brainly.com/question/30507236

#SPJ11

The electrical-mechanical analogy is an analogy used to understand the behavior of oscillating systems, both electrical and mechanical.

In the realm of mechanics, a mass's deviance from its equilibrium location is represented by a differential equation:

m( d ²ˣ / dt ² )  + kx = 0

where m is the mass of the object, k is the spring constant, and x is the displacement from equilibrium.

In electrical systems, however, a capacitor's voltage in an RLC circuit can be described using this differential equation:

L ( d ² Q / dt ² ) + R ( dQ / dt ) + ( 1/C ) Q = 0

where L is the inductance, R is the resistance, C is the capacitance, and Q is the charge on the capacitor.

Upon studying these two equations, it becomes clear that the deviation of a mechanical system's mass correlates to the charge on an electrical system's capacitor. Similarly, while a mechanical system identifies its spring constant with the capacitance's inverse, this same correlation exists in electrical systems as well.

Find out more on oscillating systems at https://brainly.com/question/15454378

#SPJ1

The gain in gravitational potential energy for 115 ml of blood raised 37 cm is approximately 0.44 J.

To calculate the gravitational potential energy, we need to multiply the mass of the blood by the acceleration due to gravity ([tex]9.8 m/s^2[/tex]) and the height it was raised. The mass of [tex]115 ml[/tex] of blood can be calculated using its density of [tex]1050 kg/m^3[/tex]. The volume can be converted to cubic meters, and then multiplied by the density to get the mass.

The gain in gravitational potential energy can be calculated using the formula: Potential Energy (PE) = mass × acceleration due to gravity × height.

The height of 37 cm can be converted to meters. Plugging in the numbers, we get [tex](0.115 kg) \times (9.8 m/s^2) \times (0.37 m) = 0.44 J[/tex].

To learn more about gravitational, Click here: brainly.com/question/3009841

#SPJ11

The angle the transmitted beam makes with the horizontal axis is approximately 16.2°.

To find the angle φ₃,v, we need to use Snell's Law, which states that the ratio of the sine of the angle of incidence to the sine of the angle of refraction is equal to the ratio of the indices of refraction of the two media. In this case, we can use the following equation:

sin(φ₁,v) / sin(φ₂,v) = n₂ / n₁

where φ₁,v is the angle of incidence, φ₂,v is the angle of refraction, n₁ is the index of refraction of the medium the violet beam is coming from (air, assumed to be 1), and n₂ is the index of refraction of the medium the violet beam is entering (water, assumed to be 1.33).

Rearranging the equation, we get:

sin(φ₂,v) = sin(φ₁,v) * n₁ / n₂

Plugging in the given values, we get:

sin(φ₂,v) = sin(60°) * 1 / 1.33 ≈ 0.566

Now we can use trigonometry to find the angle φ₃,v. We know that the transmitted beam will bend away from the normal, which is perpendicular to the surface of the water. Therefore, we can draw a right triangle with the normal as one leg, the transmitted beam as another leg, and the angle of refraction φ₂,v as the hypotenuse.

Using the sine function again, we can find the length of the leg opposite to φ₃,v:

sin(φ₃,v) = sin(90° - φ₂,v) * 0.566

sin(φ₃,v) = cos(φ₂,v) * 0.566

sin(φ₃,v) ≈ 0.276

Taking the inverse sine of both sides, we get:

φ₃,v ≈ 16.2°

Therefore, the angle the transmitted beam makes with the horizontal axis is approximately 16.2°.

To know more about beam, refer

https://brainly.com/question/29600302

#SPJ11

The volume of radon gas produced will be 6.56 × 10⁻⁶ L, is produced by 29.0 g of radium in 5.0 days.

The production of radon from radium can be represented by the radioactive decay equation;

226Ra → 222Rn + alpha particle

The molar mass of radium is 226 g/mol. From the equation, we see that for every 1 mole of radium that decays, 1 mole of radon is produced. The Avogadro's number is used to convert the number of moles to the number of atoms.

First, let's calculate the number of moles of radium that decay in 5.0 days:

1 mole of 226Ra decays into 1 mole of 222Rn + 1 alpha particle

1 mole of 226Ra = 226 g

Number of moles of 226Ra = mass / molar mass

= 29.0 g / 226 g/mol = 0.1283 mol

The half-life of 226Ra is about 1600 years, which means that the activity (i.e., the rate of decay) of 1 gram of 226Ra is about 1.35 × 10⁴ disintegrations per second (Becquerels). The activity of 29.0 g of 226Ra can be calculated as follows;

Activity = (29.0 g) × (1.35 × 10⁴ disintegrations/g/s)

= 3.92 × 10⁵ disintegrations/s

Each decay produces one atom of radon gas, so the number of atoms of radon produced in 5.0 days is:

Number of atoms of 222Rn = Activity × time = (3.92 × 10⁵ disintegrations/s) × (5.0 days × 24 hours/day × 60 min/hour × 60 s/min) = 1.70 × 10¹⁷ atoms

The ideal gas law can be used to calculate the volume of radon gas produced;

PV = nRT

where P is the pressure (1 atm), V is the volume we want to calculate, n is the number of moles of gas, R is the gas constant (0.0821 L·atm/(mol·K)), and T is the temperature in Kelvin (25.0 °C + 273.15 = 298.15 K).

n = N/N_A where N_A is Avogadro's number (6.022 × 10²³ mol⁻¹)

n = (1.70 × 10¹⁷ atoms) / (6.022 × 10²³ mol⁻¹)

= 2.83 × 10⁻⁷ mol

Substituting the values into ideal gas law;

V = nRT/P = (2.83 × 10⁻⁷ mol) × (0.0821 L·atm/(mol·K)) × (298.15 K) / (1 atm) = 6.56 × 10⁻⁶ L

Therefore, the volume of radon gas produced is 6.56 × 10⁻⁶ L (or 6.56 μL).

To know more about radon gas here

https://brainly.com/question/13526655

#SPJ4

Both objects, the 10kg iron, and the 10kg cotton, will reach the ground at the same time if air resistance is ignored.

This result is because, in the absence of air resistance, the acceleration of a falling object is independent of its mass. All objects, regardless of their mass, will experience the same acceleration due to gravity. This acceleration is approximately 9.8 m/s^2 near the surface of the Earth. Therefore, the time taken for both objects to fall to the ground from the same height will be the same, and they will hit the ground at the same time. However, in the presence of air resistance, the results will be different as air resistance affects objects differently based on their shape and size.

To learn more about air resistance : brainly.com/question/11019447

#SPJ11

Answer:

Explanation: The object that would take the most force to move is the car as the car has the most mass out of all the objects.

-The car will take the most force to move because newtons 1st law of motion states that an object will continue in a state rest unless acted on by an unbalanced force but since the car has a large amount of mass It will be harder to move due to inertia as the more mass it has the more inertia it will have

To create a diffuse sound field within a theater, the goal is to distribute sound energy evenly throughout the space, reducing the presence of distinct echoes and reflections.

Among the given options, the treatment that would best contribute to this acoustic characteristic is:

(c) Velvet curtains hung on the side walls of the theater.

Velvet curtains have a soft and textured surface that can absorb and scatter sound waves, preventing them from reflecting directly back into the audience or creating focused sound reflections. This helps to reduce the presence of strong reflections and echoes, promoting a more diffuse sound field within the theater.

Learn more about diffuse sound field  here:

https://brainly.com/question/18534026

#SPJ11

We can use the formula for wave speed on a string: v = sqrt(T/μ), where v is the wave speed, T is the tension, and μ is the mass per unit length of the string. To solve for T, we can rearrange the equation to T = μv^2.

Substituting the given values, we have:

μ = density x cross-sectional area = 2.70 x 10^3 kg/m^3 x π(1.00 x 10^-3 m)^2 = 8.51 x 10^-6 kg/m

v = 120 m/s

Plugging these values into the formula, we get:

T = μv^2 = (8.51 x 10^-6 kg/m) x (120 m/s)^2 = 12.3 N

Therefore, the tension in the aluminum wire is 12.3 N.

Learn more about the cross-sectional area here:- brainly.com/question/20532494

#SPJ11

The drift velocity in a conductor refers to the net velocity of free electrons in a conductor when a voltage is applied, which is typically very slow, on the order of millimeters per second.

On the other hand, the speed of an electrical signal, also known as the signal propagation speed, refers to the speed at which changes in electric fields and currents propagate through a conductor or other medium, typically at close to the speed of light.

The propagation speed depends on the properties of the medium, such as its dielectric constant and permeability, and can be much faster than the drift velocity of the electrons.

Learn more about The drift velocity

https://brainly.com/question/4269562

#SPJ4

450 j of work are done on a gas in a process which decreases the thermal energy by 200 j . 250 J heat energy is transferred to or from the system

In this situation, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system.
ΔU = Q - W

Energy cannot be generated or destroyed but can only be changed from one form to another, according to the rule of conservation of energy.
We know that the work done on the gas is 450 J, and that the thermal energy of the gas decreases by 200 J. Therefore, the change in internal energy of the gas is:
ΔU = -200 J
To find the heat transferred, we can rearrange the equation above:
Q = ΔU + W
Substituting the values we know, we get:
Q = -200 J + 450 J = 250 J
Therefore, 250 J of heat energy was transferred to the system.

Learn more conservation of energy here

https://brainly.com/question/27904747

#SPJ11

250 J of heat energy is transferred out of the system.

In this scenario, 450 J of work is done on the gas, which means that energy is transferred to the system. However, the thermal energy of the system decreases by 200 J, which indicates that heat energy is being transferred out of the system. This means that the remaining energy, which is the difference between the work done and the change in thermal energy, must be the amount of heat energy transferred out of the system.
Therefore, the amount of heat energy transferred out of the system can be calculated by subtracting the decrease in thermal energy from the work done:
Heat energy = Work done - Change in thermal energy
Heat energy = 450 J - 200 J
Heat energy = 250 J

So, 250 J of heat energy is transferred out of the system.

learn more about heat energy Refer: https://brainly.com/question/31367000

#SPJ11

Answer:

Explanation:

True   it is usually billed monthly and will show the kilowatt-hrs you used

The relative values of r2 and r1 for the subtractor circuit with output vo = gain(v2 – v1) and gain = 6 is r1 = 6.5 kΩ and r2 = 130 kΩ * (v2 - vo) / vo.

The relative values of r2 and r1 for the subtractor circuit with output vo = gain(v2 – v1) and gain = 6 is as follows:

Since R4 = (gain - 1) * R3 = 5 * 26 kΩ = 130 kΩ, we can use the voltage divider formula to find the value of R2:

R2 = R4 * (V2 - Vo) / Vo = 130 kΩ * (V2 - Vo) / Vo

We also know that the voltage at the inverting input of the op-amp is equal to V1, so we can write:

Vo = -R2/R1 * V1

Substituting for R2, we get:

Vo = -R4*(V2-Vo)/(6VoR1)

Simplifying and solving for R1, we get:

R1 = (V2 - Vo) / (6 * Vo * V1 / R4) - R4

Plugging in the given values and solving, we get:

R1 = 6.5 kΩ

Thus, the relative values of r2 and r1 should be such that r1 = 6.5 kΩ and r2 = 130 kΩ * (v2 - vo) / vo.

To learn more about Circuit click here

https://brainly.com/question/12608491

#SPJ11

The magnetic field lines due to a straight line of current will appear as circular lines around the current, with the direction of the magnetic field lines pointing from the positive current end to the negative current end. Option 3 is Correct.

The magnetic field lines due to a straight line of current will appear as circular lines around the current. The direction of the magnetic field lines is determined by the direction of the current, and they will be oriented perpendicular to the direction of the current.

The direction of the magnetic field lines is also related to the right-hand rule, which states that if you curl your fingers in the direction of the current and point your thumb in the direction of the magnetic field lines, your thumb will point in the direction of the magnetic field. Option 3 is Correct.

Learn more about magnetic field visit: brainly.com/question/14411049

#SPJ4

Correct Question:

If you are looking at a straight line of current coming towards you, the magnetic field lines due to this current will appear as ...

1. radial lines going straight away from the current.

2. circles around the current going clockwise.

3. circles around the current going counter-clockwise.

4. radial lines going straight towards the current.

Sphere A= 1.4nC and sphere B=-5.9nC ,The charge on sphere B after contact is in -2.25 nC in No measurements are done after the sphere.

To find the charge on sphere B after contact, we need to consider charge conservation since the two identical spheres will redistribute their charges equally. The total initial charge is the sum of charges on sphere A and sphere B:
[tex]Total charge = Sphere A charge + Sphere B charge[/tex]
Total charge = 1.4 nC + (-5.9 nC)
Total charge = -4.5 nC

Potential often refers to a talent that is still being refined. The phrase is used to describe items that are in a condition where they have the potential to change in a number of ways, from the simple release of energy by objects to the realisation of skills in individuals, in a wide range of fields, from physics to the social sciences.
After contact, the charges will be distributed equally between the two spheres:
Charge on sphere B after contact = Total charge / 2
Charge on sphere B after contact = -4.5 nC / 2
Charge on sphere B after contact = -2.25 nC

Learn more about Potential here

https://brainly.com/question/29583143

#SPJ11

The frequency of a school class change bell can vary depending on the school's schedule and preferences. However, a common frequency for class change bells is typically in the range of 1 to 5 Hz (hertz).

It's important to note that the frequency refers to the number of cycles or repetitions per second. In the context of a class change bell, the frequency represents the number of times the bell rings within a given time frame. Specifically, a frequency of 1 Hz would mean the bell rings once per second, while a frequency of 5 Hz would mean the bell rings five times per second. Please keep in mind that the actual frequency of a school class change bell can vary between different educational institutions, so it's always best to consult with the school or refer to their specific schedule for accurate information.

To know more about frequency, click here https://brainly.com/question/2140860

#SPJ11