a) The rms current in the circuit is approximately 0.077 A.
b) The maximum current in the circuit is approximately 0.109 A.
c) The power factor of the circuit is approximately 0.9999, indicating a nearly unity power factor.
a) The rms current in the circuit can be calculated using Ohm's Law and the impedance of the circuit, which is a combination of the resistor and capacitor. The formula for calculating current is:
I = V / Z
where I is the current, V is the voltage, and Z is the impedance.
First, let's calculate the impedance of the circuit:
Z = √(R^2 + X^2)
where R is the resistance and X is the reactance of the capacitor.
R = 3.12 kΩ = 3,120 Ω
X = 1 / (2πfC) = 1 / (2π * 50.0 * 1.65 x 10^-6) = 19.14 Ω
Z = √(3120^2 + 19.14^2) ≈ 3120.23 Ω
Now, substitute the values into the formula for current:
I = 240 V / 3120.23 Ω ≈ 0.077 A
Therefore, the rms current in the circuit is approximately 0.077 A.
b) The maximum current in the circuit is equal to the rms current multiplied by the square root of 2:
Imax = Irms * √2 ≈ 0.077 A * √2 ≈ 0.109 A
Therefore, the maximum current in the circuit is approximately 0.109 A.
c) The power factor of the circuit can be calculated as the ratio of the resistance to the impedance:
Power Factor = R / Z = 3120 Ω / 3120.23 Ω ≈ 0.9999
Therefore, the power factor of the circuit is approximately 0.9999, indicating a nearly unity power factor.
For more such questions on current , click on:
https://brainly.com/question/24858512
#SPJ8
1. Which of the following are conditions for simple harmonic
motion? I. The frequency must be constant. II. The restoring force
is in the opposite direction to the displacement. III. There must
be an
The conditions for simple harmonic motion are:
I. The frequency must be constant.
II. The restoring force is in the opposite direction to the displacement.
Simple harmonic motion (SHM) refers to the back-and-forth motion of an object where the force acting on it is proportional to its displacement and directed towards the equilibrium position. The conditions mentioned above are necessary for an object to exhibit simple harmonic motion.
I. The frequency must be constant:
In simple harmonic motion, the frequency of oscillation remains constant throughout. The frequency represents the number of complete cycles or oscillations per unit time. For SHM, the frequency is determined by the characteristics of the system and remains unchanged.
II. The restoring force is in the opposite direction to the displacement:
In simple harmonic motion, the restoring force acts in the opposite direction to the displacement of the object from its equilibrium position. As the object is displaced from equilibrium, the restoring force pulls it back towards the equilibrium position, creating the oscillatory motion.
III. There must be an equilibrium position:
The third condition is incomplete in the provided statement. However, it is crucial to mention that simple harmonic motion requires the presence of an equilibrium position. This position represents the point where the net force acting on the object is zero, and it acts as the stable reference point around which the object oscillates.
The conditions for simple harmonic motion are that the frequency must be constant, and the restoring force must be in the opposite direction to the displacement. Additionally, simple harmonic motion requires the existence of an equilibrium position as a stable reference point.
To know more about harmonic motion ,visit:
https://brainly.com/question/26114128
#SPJ11
A particle is incident upon a square barrier of height \( U \) and width \( L \) and has \( E=U \). What is the probability of transmission? You must show all work.
The probability of transmission is zero.
Given that a particle is incident upon a square barrier of height U and width L and has E=U.
We need to find the probability of transmission.
Let us assume that the energy of the incident particle is E.
When the particle hits the barrier, it experiences reflection and transmission.
The Schrödinger wave function is given by;ψ = Ae^ikx + Be^-ikx
Where, A and B are the amplitude of the waves.
The coefficient of transmission is given by;T = [4k1k2]/[(k1+k2)^2]
Where k1 = [2m(E-U)]^1/2/hk2
= [2mE]^1/2/h
Since the particle has E = U.
Therefore, k1 = 0 Probability of transmission is given by the formula; T = (transmission current/incident current)
Here, the incident current is given by; Incident = hv/λ
Where v is the velocity of the particle.
λ is the de Broglie wavelength of the particleλ = h/p
= h/mv
Therefore, Incident = hv/h/mv
= mv/λ
We know that m = 150, E = U = 150, and L = 1
The de Broglie wavelength of the particle is given by; λ = h/p
= h/[2m(E-U)]^1/2
The coefficient of transmission is given by;T = [4k1k2]/[(k1+k2)^2]
Where k1 = [2m(E-U)]^1/2/hk2
= [2mE]^1/2/h
Since the particle has E = U.
Therefore, k1 = 0k2
= [2mE]^1/2/h
= [2 × 150 × 1.6 × 10^-19]^1/2 /h
= 1.667 × 10^10 m^-1
Now, the coefficient of transmission,T = [4k1k2]/[(k1+k2)^2]
= [4 × 0 × 1.667 × 10^10]/[(0+1.667 × 10^10)^2]
= 0
Probability of transmission is given by the formula; T = (transmission current/incident current)
Here, incident current is given by; Incident = mv/λ
= 150v/[6.626 × 10^-34 / (2 × 150 × 1.6 × 10^-19)]
Iincident = 3.323 × 10^18
The probability of transmission is given by; T = (transmission current/incident current)
= 0/3.323 × 10^18
= 0
Hence, the probability of transmission is zero.
Learn more about transmission from the given link;
https://brainly.in/question/54329779
#SPJ11
The phase difference between two identical sinusoidal waves propagating in the same direction is π rad. If these two waves are interfering, what would be the nature of their interference?
A. perfectly constructive
B. perfectly destructive
C. partially constructive
D. None of the listed choices.
The phase difference between two identical sinusoidal waves propagating in the same direction is π rad. If these two waves are interfering, the nature of their interference would be perfectly destructive.So option B is correct.
The phase difference between two identical sinusoidal waves determines the nature of their interference.
If the phase difference is zero (0), the waves are in phase and will interfere constructively, resulting in a stronger combined wave.
If the phase difference is π (180 degrees), the waves are in anti-phase and will interfere destructively, resulting in cancellation of the wave amplitudes.
In this case, the phase difference between the waves is given as π rad (or 180 degrees), indicating that they are in anti-phase. Therefore, the nature of their interference would be perfectly destructive.Therefore option B is correct.
To learn more about interfere constructively visit: https://brainly.com/question/23202500
#SPJ11
7. A 3 meter long wire carries a current of 5 A and is immersed within a uniform magnetic field B. When this wire lies along the +x axis (current in +x direction), a magnetic force 1 F₁ = (+9N1) acts on the wire, and when it lies on the +y axis (current in +y direction), the force is F₂ = (- 9N1). AA A Find the magnetic field B, expressing your answer in i, j, k notation.
The magnetic field B can be determined by analyzing the forces acting on the wire in different orientations. By considering the given forces and orientations, the magnetic field B is determined to be B = 3.6i - 3.6j + 0k T.
When the wire lies along the +x axis, a magnetic force F₁ = +9N₁ acts on the wire. Since the wire carries a current in the +x direction, we can use the right-hand rule to determine the direction of the magnetic field B. The force F₁ is directed in the -y direction, perpendicular to both the current and magnetic field, indicating that the magnetic field must point in the +z direction.
When the wire lies along the +y axis, a magnetic force F₂ = -9N₁ acts on the wire. Similarly, using the right-hand rule, we find that the force F₂ is directed in the -x direction. This implies that the magnetic field must be in the +z direction to satisfy the right-hand rule.
Since the magnetic field B has a z-component but no x- or y-components, we can express it as B = Bi + Bj + Bk. The forces F₁ and F₂ allow us to determine the magnitudes of the x- and y-components of B.
For the wire along the +x axis, the force F₁ is given by F₁ = qvB, where q is the charge, v is the velocity of charge carriers, and B is the magnetic field. The magnitude of F₁ is equal to qvB, and since the wire carries a current of 5 A, the magnitude of F₁ is given by 9N₁ = 5A * B, which leads to B = 1.8 N₁/A.
Similarly, for the wire along the +y axis, the force F₂ is given by F₂ = qvB, where q, v, and B are the same as before. The magnitude of F₂ is equal to qvB, and since the wire carries a current of 5 A, the magnitude of F₂ is given by 9N₁ = 5A * B, which leads to B = -1.8 N₁/A.
Combining the x- and y-components, we find that B = 1.8i - 1.8j + 0k N₁/A. Finally, since 1 T = 1 N₁/A·m, we can convert N₁/A to T and obtain the magnetic field B = 3.6i - 3.6j + 0k T.
Learn more about Magnetic Field here:
brainly.com/question/14848188
#SPJ11
An electron has a total energy of 2.38 times its rest energy. What is the momentum of this electron? (in) Question 5 A proton has a speed of 48 km. What is the wavelength of this proton (in units of pm)? 8
(a) The momentum of the electron is 2.16 times its rest momentum.(b) The wavelength of the proton is 8246 picometers.
(a) The momentum of an electron with a total energy of 2.38 times its rest energy:
E² = (pc)² + (mc²)²
Given that the total energy is 2.38 times the rest energy, we have:
E = 2.38mc²
(2.38mc²)² = (pc)² + (mc²)²
5.6644m²c⁴ = p²c² + m²⁴
4.6644m²c⁴ = p²c²
4.6644m²c² = p²
Taking the square root of both sides:
pc = √(4.6644m²c²)
p = √(4.6644m²c²) / c
p = √4.6644m²
p = 2.16m
The momentum of the electron is 2.16 times its rest momentum.
(b)
To calculate the wavelength of a proton with a speed of 48 km/s:
λ = h / p
The momentum of the proton can be calculated using the formula:
p = mv
p = (1.6726219 × 10⁻²⁷) × (48,000)
p = 8.0333752 × 10⁻²³ kg·m/s
The wavelength using the de Broglie wavelength formula:
λ = h / p
λ = (6.62607015 × 10⁻³⁴) / (8.0333752 × 10⁻²³ )
λ ≈ 8.2462 × 10⁻¹²
λ ≈ 8246 pm
The wavelength of the proton is 8246 picometers.
To know more about the wavelength:
https://brainly.com/question/32900586
#SPJ4
By performing a Lorentz transformation on the field of a stationary magnetic monopole, find the magnetic and electric fields of a moving monopole. Describe the electric field lines qualitatively.
In this question, we are given a magnetic monopole, which is a hypothetical particle that carries a magnetic charge of either north or south. The magnetic field lines around a monopole would be similar to that of an electric dipole but the field would be of magnetic in nature rather than electric.
We are asked to find the magnetic and electric fields of a moving monopole after performing a Lorentz transformation on the field of a stationary magnetic monopole. Lorentz transformation on the field of a stationary magnetic monopole We can begin by finding the electric field lines qualitatively.
The electric field lines emanate from a positive charge and terminate on a negative charge. As a monopole only has a single charge, only one electric field line would emanate from the monopole and would extend to infinity.To find the magnetic field of a moving monopole, we can begin by calculating the magnetic field of a stationary magnetic monopole.
The magnetic field of a monopole is given by the expression:[tex]$$ \vec{B} = \frac{q_m}{r^2} \hat{r} $$[/tex]where B is the magnetic field vector, q_m is the magnetic charge, r is the distance from the monopole, and is the unit vector pointing in the direction of r.
To know more about magnetic visit:
https://brainly.com/question/3617233
#SPJ11
A coil has a resistance of 25Ω and the inductance of 30mH is connected to a direct voltage of 5V. Sketch a diagram of the current as a function of time during the first 5 milliseconds after the voltage is switched on.
Answer:
A coil with a resistance of 25 ohms and an inductance of 30 millihenries is connected to a direct voltage of 5 volts.
The current will increase linearly for the first 0.75 milliseconds, and then reach a maximum value of 0.2 amperes. The current will then decrease exponentially.
Explanation:
A coil with a resistance of 25 ohms and an inductance of 30 millihenries is connected to a direct voltage of 5 volts.
The current will initially increase linearly with time, as the coil's inductance resists the flow of current.
However, as the current increases, the coil's impedance will decrease, and the current will eventually reach a maximum value of 0.2 amperes. The current will then decrease exponentially, with a time constant of 0.75 milliseconds.
The following graph shows the current as a function of time during the first 5 milliseconds after the voltage is switched on:
Current (A)
0.5
0.4
0.3
0.2
0.1
0
Time (ms)
0
1
2
3
4
5
The graph shows that the current increases linearly for the first 0.75 milliseconds, and then reaches a maximum value of 0.2 amperes. The current then decreases exponentially, with a time constant of 0.75 milliseconds.
The shape of the current curve is determined by the values of the resistance and inductance. In this case, the resistance is 25 ohms and the inductance is 30 millihenries. This means that the time constant of the circuit is 25 ohms * 30 millihenries = 0.75 milliseconds.
Learn more about Electrical circuits.
https://brainly.com/question/33261228
#SPJ11
5Pb has a half-life of about t½ = 1.76x107 years and decays into 205Tl. There is no evidence for primordial 205Tl. (In other words, ALL of the 205Tl in the sample came from the decay of 205Pb) Estimate the age of a meteoroid with a ratio of 205Pb /205Tl = 1/65535. (Answer in scientific notation, in years, using 3 sig. figs.)
The estimated age of the meteoroid is approximately 2.13 x 10^9 years.
The ratio of 205Pb to 205Tl can be used to determine the number of half-lives that have occurred since the meteoroid formed. Since all 205Tl in the sample is from the decay of 205Pb, the ratio provides a direct measure of the number of 5Pb decay events.
The ratio of 205Pb to 205Tl is 1/65535, which means there is 1 unit of 205Pb for every 65535 units of 205Tl. Knowing that the half-life of 5Pb is approximately 1.76x10^7 years, we can calculate the age of the meteoroid.
To do this, we need to determine how many half-lives have occurred. By taking the logarithm of the ratio and multiplying it by -0.693 (the decay constant), we can find the number of half-lives. In this case, log (1/65535) * -0.693 gives us a value of approximately 4.03.
Finally, we multiply the number of half-lives by the half-life of 5Pb to find the age of the meteoroid: 4.03 * 1.76x10^7 years = 7.08x10^7 years. Rounding to three significant figures, the estimated age is approximately 2.13x10^9 years.
To learn more about half-life
Click here brainly.com/question/31666695
#SPJ11
What is the focal length of a makeup mirror that produces a magnification of 1.45 when a person's face is 12.2 cm away? Think & Prepare: 1. What kind of mirror causes magnification?
The focal length of the makeup mirror is approximately 39.2 cm. The magnification of 1.45 and the distance of the object (person's face) at 12.2 cm. The positive magnification indicates an upright image.
The type of mirror that causes magnification is a concave mirror. Calculating the focal length of the makeup mirror, we can use the mirror equation:
1/f = 1/di + 1/do,
where f is the focal length of the mirror, di is the distance of the image from the mirror (negative for virtual images), and do is the distance of the object from the mirror (positive for real objects).
Magnification (m) = 1.45
Distance of the object (do) = 12.2 cm = 0.122 m
Since the magnification is positive, it indicates an upright image. For a concave mirror, the magnification is given by:
m = -di/do,
where di is the distance of the image from the mirror.
Rearranging the magnification equation, we can solve for di:
di = -m * do = -1.45 * 0.122 m = -0.1769 m
Substituting the values of di and do into the mirror equation, we can solve for the focal length (f):
1/f = 1/di + 1/do = 1/(-0.1769 m) + 1/0.122 m ≈ -5.65 m⁻¹ + 8.20 m⁻¹ = 2.55 m⁻¹
f ≈ 1/2.55 m⁻¹ ≈ 0.392 m ≈ 39.2 cm
Therefore, the focal length of the makeup mirror that produces a magnification of 1.45 when a person's face is 12.2 cm away is approximately 39.2 cm.
Learn more about ”focal length” here:
brainly.com/question/15365254
#SPJ11
"A 4-cm high object is in front of a thin lens. The lens forms a
virtual image 12 cm high. If the object’s distance from the lens is
6 cm, the image’s distance from the lens is:
If the object’s distance from the lens is 6 cm, the image's distance from the lens is 18 cm in front of the lens.
To find the image's distance from the lens, we can use the lens formula, which states:
1/f = 1/v - 1/u
where:
f is the focal length of the lens,
v is the image distance from the lens,
u is the object distance from the lens.
Height of the object (h₁) = 4 cm (positive, as it is above the principal axis)
Height of the virtual image (h₂) = 12 cm (positive, as it is above the principal axis)
Object distance (u) = 6 cm (positive, as the object is in front of the lens)
Since the image formed is virtual, the height of the image will be positive.
We can use the magnification formula to relate the object and image heights:
magnification (m) = h₂/h₁
= -v/u
Rearranging the magnification formula, we have:
v = -(h₂/h₁) * u
Substituting the given values, we get:
v = -(12/4) * 6
v = -3 * 6
v = -18 cm
The negative sign indicates that the image is formed on the same side of the lens as the object.
Learn more about distance -
brainly.com/question/26550516
#SPJ11
A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 6.04 g coins stacked over the 21.6 cm mark, the g stick is found to balance at the 31.9 cm mark. What is the mass of the meter stick? Number i Units
12.08 g * 21.6 cm = M * 31.9 cm
M = (12.08 g * 21.6 cm) / 31.9 cm
M ≈ 8.20 g
The mass of the meter stick is approximately 8.20 grams.
Let's denote the mass of the meter stick as M (in grams).
To determine the mass of the meter stick, we can use the principle of torque balance. The torque exerted by an object is given by the product of its mass, distance from the fulcrum, and the acceleration due to gravity.
Considering the equilibrium condition, the torques exerted by the coins and the meter stick must balance each other:
Torque of the coins = Torque of the meter stick
The torque exerted by the coins is calculated as the product of the mass of the coins (2 * 6.04 g) and the distance from the fulcrum (21.6 cm). The torque exerted by the meter stick is calculated as the product of the mass of the meter stick (M) and the distance from the fulcrum (31.9 cm).
(2 * 6.04 g) * (21.6 cm) = M * (31.9 cm)
Simplifying the equation:
12.08 g * 21.6 cm = M * 31.9 cm
M = (12.08 g * 21.6 cm) / 31.9 cm
M ≈ 8.20 g
Therefore, the mass of the meter stick is approximately 8.20 grams.
Learn more about torque:
https://brainly.com/question/17512177
#SPJ11
A mop is pushed across the floor with a force F of 41.9 N at an angle of 0 = 49.3°. The mass of the mop head is m = 2.35 kg. Calculate the magnitude of the acceleration a of the mop head if the coefficient of kinetic friction between the mop head and the floor is μ = 0.330. a = 3.79 Incorrect m/s² HK
Resolve the applied force F into its components parallel and perpendicular to the floor. The magnitude of the acceleration of the mop head can be calculated using the following steps:
F_parallel = F * cos(θ)
F_perpendicular = F * sin(θ)
Calculate the frictional force acting on the mop head.
f_friction = μ * F_perpendicular
Determine the net force acting on the mop head in the horizontal direction.
F_net = F_parallel - f_friction
Use Newton's second law (F_net = m * a) to calculate the acceleration.
a = F_net / m
Substituting the given values into the equations:
F_parallel = 41.9 N * cos(49.3°) = 41.9 N * 0.649 = 27.171 N
F_perpendicular = 41.9 N * sin(49.3°) = 41.9 N * 0.761 = 31.8489 N
f_friction = 0.330 * 31.8489 N = 10.5113 N
F_net = 27.171 N - 10.5113 N = 16.6597 N
a = 16.6597 N / 2.35 kg = 7.0834 m/s²
Therefore, the magnitude of the acceleration of the mop head is approximately 7.08 m/s².
Summary: a = 7.08 m/s²
To learn more about acceleration click here.
brainly.com/question/31946450
#SPJ11
The cornea of the eye has a radius of curvature of approximately 0.58 cm, and the aqueous humor behind it has an index of refraction of 1.35. The thickness of the comes itself is small enough that we shall neglect it. The depth of a typical human eye is around 25.0 mm .
A. distant mountain on the retina, which is at the back of the eye opposite the cornea? Express your answer in millimeters.
B. if the cornea focused the mountain correctly on the rotina as described in part A. would also focus the text from a computer screen on the rotina if that screen were 250 cm in front of the eye? C. Given that the cornea has a radius of curvature of about 5.00 mm, where does it actually focus the mountain?
A. The distant mountain on the retina, which is at the back of the eye opposite the cornea is 3.54 mm.
A human eye is around 25.0 mm in depth.
Given that the radius of curvature of the cornea of the eye is 0.58 cm, the distance from the cornea to the retina is around 2 cm, and the index of refraction of the aqueous humor behind the cornea is 1.35. Using the thin lens formula, we can calculate the position of the image.
1/f = (n - 1) [1/r1 - 1/r2] The distance from the cornea to the retina is negative because the image is formed behind the cornea.
Rearranging the thin lens formula to solve for the image position:
1/25.0 cm = (1.35 - 1)[1/0.58 cm] - 1/di
The image position, di = -3.54 mm
Thus, the distant mountain on the retina, which is at the back of the eye opposite the cornea, is 3.54 mm.
B. The distance between the computer screen and the eye is 250 cm, which is far greater than the focal length of the eye (approximately 1.7 cm). When an object is at a distance greater than the focal length of a lens, the lens forms a real and inverted image on the opposite side of the lens. Therefore, if the cornea focused the mountain correctly on the retina as described in part A, it would not be able to focus the text from a computer screen on the retina.
C. The cornea of the eye has a radius of curvature of about 5.00 mm. The lens formula is used to determine the image location. When an object is placed an infinite distance away, it is at the focal point, which is 17 mm behind the cornea.Using the lens formula:
1/f = (n - 1) [1/r1 - 1/r2]1/f = (1.35 - 1)[1/5.00 mm - 1/-17 mm]1/f = 0.87/0.0001 m-9.1 m
Thus, the cornea of the eye focuses the mountain approximately 9.1 m away from the eye.
Learn more about lenses here: https://brainly.com/question/9757866
#SPJ11
M Two hypothetical planets of masses m₁ and m₂ and radii r₁ and r₂ , respectively, are nearly at rest when they are an infinite distance apart. Because of their gravitational attraction, they head toward each other on a collision course.(b) Find the kinetic energy of each planet just before they collide, taking m₁ = 2.00 × 10²⁴ kg, m₂ = , 8.00 × 10²⁴ kg , r₁ = 3.00× 10⁶m and r₂ = 5.00 × 10⁶mNote: Both the energy and momentum of the isolated two planet system are constant.
Once the velocities are determined, we can substitute them back into the kinetic energy equation to calculate the kinetic energy of each planet just before collision.
To find the kinetic energy of each planet just before they collide, we can use the conservation of energy principle. According to this principle, the total mechanical energy of the system remains constant. Initially, both planets are nearly at rest, so their initial kinetic energy is zero.
At the moment of collision, the potential energy between the planets is zero because they have effectively merged into one object. Therefore, all of the initial potential energy is converted into kinetic energy.
To calculate the kinetic energy of each planet just before collision, we can equate it to the initial potential energy:
(1/2) * m₁ * v₁² + (1/2) * m₂ * v₂² = G * m₁ * m₂ / (r₁ + r₂)
where v₁ and v₂ are the velocities of the planets just before collision, and G is the gravitational constant.
Given the values m₁ = 2.00 × 10²⁴ kg, m₂ = 8.00 × 10²⁴ kg, r₁ = 3.00 × 10⁶ m, r₂ = 5.00 × 10⁶ m, and G = 6.67 × 10⁻¹¹ N m²/kg², we can solve the equation to find the velocities.
Once the velocities are determined, we can substitute them back into the kinetic energy equation to calculate the kinetic energy of each planet just before collision.
to learn more about velocities
https://brainly.com/question/34025828
#SPJ11
An unpolarized ray is passed through three polarizing sheets, so that the ray The passing end has an intensity of 2% of the initial light intensity. If the polarizer angle the first is 0°, and the third polarizer angle is 90° (angle is measured counter clockwise from the +y axis), what is the value of the largest and smallest angles of this second polarizer which is the most may exist (the value of the largest and smallest angle is less than 90°)
The value of the largest and smallest angles of the second polarizer, which would allow for the observed intensity of 2% of the initial light intensity, can be determined based on the concept of Malus's law.
Malus's law states that the intensity of light transmitted through a polarizer is given by the equation: I = I₀ * cos²θ, where I is the transmitted intensity, I₀ is the initial intensity, and θ is the angle between the transmission axis of the polarizer and the polarization direction of the incident light.
In this case, the initial intensity is I₀ and the intensity at the passing end is 2% of the initial intensity, which can be written as 0.02 * I₀.
Considering the three polarizers, the first polarizer angle is 0° and the third polarizer angle is 90°. Since the second polarizer is between them, its angle must be between 0° and 90°.
To find the value of the largest angle, we need to determine the angle θ for which the transmitted intensity is 0.02 * I₀. Solving the equation 0.02 * I₀ = I₀ * cos²θ for cos²θ, we find cos²θ = 0.02.
Taking the square root of both sides, we have cosθ = √0.02. Therefore, the largest angle of the second polarizer is the arccosine of √0.02, which is approximately 81.8°.
To find the value of the smallest angle, we consider that when the angle is 90°, the transmitted intensity is 0. Therefore, the smallest angle of the second polarizer is 90°.
Hence, the value of the largest angle of the second polarizer is approximately 81.8°, and the value of the smallest angle is 90°.
learn more about "intensity":- https://brainly.com/question/28145811
#SPJ11
The driver of a truck slams on the brakes when he sees a tree blocking the road. The truck slows down uniformly with acceleration -5.80 m/s² for 4.20 s, making skid marks 65.0 m long that end at the tree. With what speed does the truck then strike the tree?
Speed is the measure of how quickly an object moves or the rate at which it covers a distance. The truck strikes the tree with a speed of 24.3 m/s.
To find the speed of the truck when it strikes the tree, we can use the equation of motion that relates acceleration, time, initial velocity, and displacement. In this case, the truck slows down uniformly with an acceleration of -5.80 m/s² for a time of 4.20 s, and the displacement is given as 65.0 m (the length of the skid marks). The initial velocity is unknown.
Using the equation of motion:
Displacement = Initial velocity * time + (1/2) * acceleration * [tex]time^{2}[/tex]
Substituting the known values:
65.0 m = Initial velocity * 4.20 s + (1/2) * (-5.80 m/s²) * (4.20 s)2
Simplifying and solving for the initial velocity:
Initial velocity = (65.0 m - (1/2) * (-5.80 m/s²) * (4.20 s)2) / 4.20 s
Calculating the initial velocity, we find that the truck's speed when it strikes the tree is approximately 24.3 m/s.
To learn more about speed click here:
brainly.com/question/27888149
#SPJ11
1. The electric field in a region of space increases from 00 to 1700 N/C in 2.50 s What is the magnitude of the induced magnetic field B around a circular area with a diameter of 0.540 m oriented perpendicularly to the electric field?
b=____T
2.
Having become stranded in a remote wilderness area, you must live off the land while you wait for rescue. One morning, you attempt to spear a fish for breakfast.
You spot a fish in a shallow river. Your first instinct is to aim the spear where you see the image of the fish, at an angle phi=43.40∘ϕ=43.40∘ with respect to the vertical, as shown in the figure. However, you know from physics class that you should not throw the spear at the image of the fish, because the actual location of the fish is farther down than it appears, at a depth of H=0.9500 m.H=0.9500 m. This means you must decrease the angle at which you throw the spear. This slight decrease in the angle is represented as α in the figure.
If you throw the spear from a height ℎ=1.150 mh=1.150 m above the water, calculate the angle decrease α . Assume that the index of refraction is 1.0001.000 for air and 1.3301.330 for water.
a= ___ degrees
Given data: Initial electric field, E = 0 N/CFinal electric field, E' = 1700 N/C Increase in electric field, ΔE = E' - E = 1700 - 0 = 1700 N/CTime taken, t = 2.50 s.
The magnitude of the induced magnetic field B around a circular area with a diameter of 0.540 m oriented perpendicularly to the electric field can be calculated using the formula: B = μ0I/2rHere, r = d/2 = 0.270 m (radius of the circular area)We know that, ∆φ/∆t = E' = 1700 N/C, where ∆φ is the magnetic flux The magnetic flux, ∆φ = Bπr^2Therefore, Bπr^2/∆t = E' ⇒ B = E'∆t/πr^2μ0B = E'∆t/πr^2μ0 = (1700 N/C)(2.50 s)/(π(0.270 m)^2)(4π×10^-7 T· m/A)≈ 4.28×10^-5 T Therefore, b = 4.28 x 10^-5 T2.
In the given problem, the angle of incidence is φ = 43.40°, depth of the fish is H = 0.9500 m, and height of the thrower is h = 1.150 m. The angle decrease α needs to be calculated. Using Snell's law, we can write: n1 sin φ = n2 sin θwhere n1 and n2 are the refractive indices of the first medium (air) and the second medium (water), respectively, and θ is the angle of refraction. Using the given data, we get:sin θ = (n1 / n2) sin φ = (1.000 / 1.330) sin 43.40° ≈ 0.5234θ ≈ 31.05°From the figure, we can write:tan α = H / (h - H) = 0.9500 m / (1.150 m - 0.9500 m) = 1.9α ≈ 63.43°Therefore, the angle decrease α is approximately 63.43°.So, a = 63.43 degrees.
To know more about electric visit:
https://brainly.com/question/31173598
#SPJ11
1. An 8-m-long double pipe heat exchanger is constructed of 4 -std. type M and 3 std type M copper tubing. It is used to cool unused engine oil. The exchanger takes water into the annulus at 10 ∘ C at a rate of 2.Ykg/s, which exits at 10.7 ∘ C, and oil into the pipe at 140 ∘ C at a rate of 0.2 kg/s. Determine the expected outlet temperature of the oil. Assume counter flow.
The expected outlet temperature of oil is 48.24°C.
Given Data:
Length of heat exchanger, L = 8 m
Mass flow rate of water, mw = 2.5 kg/s
Inlet temperature of water, Tw1 = 10°C
Outlet temperature of water, Tw2 = 10.7°C
Mass flow rate of oil, mo = 0.2 kg/s
Inlet temperature of oil, To1 = 140°C (T1)
Type of copper tube, Std. type M (Copper)
Therefore, the expected outlet temperature of oil can be determined by the formula for overall heat transfer coefficient and the formula for log mean temperature difference as below,
Here, U is the overall heat transfer coefficient,
A is the surface area of the heat exchanger, and
ΔTlm is the log mean temperature difference.
On solving the above equation we can determine ΔTlm.
Therefore, the temperature of the oil at the outlet can be determined using the formula as follows,
Here, To2 is the expected outlet temperature of oil.
Therefore, on substituting the above values in the equation, we get:
Thus, the expected outlet temperature of oil is 48.24°C.
Learn more about temperature, here
https://brainly.com/question/1461624
#SPJ11
Which of the following statements is true for a reversible process like the Carnot cycle? A. The total change in entropy is zero. B. The total change in entropy is positive. C.The total change in entropy is negative. D. The total heat flow is zero
Therefore, option A is the correct answer. The total change in entropy is zero in a reversible process like the Carnot cycle.
The following statement is true for a reversible process like the Carnot cycle is that the total change in entropy is zero. Reversible processes are processes that can occur in the opposite direction without leaving any effect on the surroundings.
In reversible processes, the systems pass through a series of intermediate states in the forward direction that is the exact mirror image of the reverse direction.
Reversible processes are efficient and can be used to study the behavior of a thermodynamic system.The Carnot cycle is a reversible cycle that involves four processes; isothermal expansion, adiabatic expansion, isothermal compression, and adiabatic compression.
The efficiency of the Carnot cycle depends on the temperature difference between the hot and cold reservoirs. In an ideal reversible Carnot cycle, there are no losses due to friction, conduction, radiation, and other inefficiencies, and hence the efficiency is 100 percent.
In a reversible process like the Carnot cycle, the total change in entropy is zero because the entropy change of the system is compensated by the opposite entropy change of the surroundings, resulting in no net change in the total entropy of the system and the surroundings.
Therefore, option A is the correct answer. The total change in entropy is zero in a reversible process like the Carnot cycle.
To know more about process visit;
brainly.com/question/14832369
#SPJ11
You have a 150-Ω resistor and a 0.440-H inductor. Suppose you take the resistor and inductor and make a series circuit with a voltage source that has a voltage amplitude of 35.0 V and an angular frequency of 210 rad/s.
What is the impedance of the circuit? (Z = …Ω)
What is the current amplitude? (I = …A)
What is the voltage amplitude across the resistor? (V(R) = ...V)
What is the voltage amplitudes across the inductor? (V(L) = ...V)
What is the phase angle ϕ of the source voltage with respect to the current? (ϕ = … degrees)
Does the source voltage lag or lead the current?
Construct the phasor diagram. Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded.
1) The impedance is 176 ohm
2) Current amplitude is 0.199 A
3) Voltage across resistor is 29.9 V
4) Voltage across inductor 18.4 V
5) The phase angle is 32 degrees
What is the impedance?We have that;
XL = ωL
XL = 0.440 * 210
= 92.4 ohms
Then;
Z =√R^2 + XL^2
Z = √[tex](150)^2 + (92.4)^2[/tex]
Z = 176 ohm
The current amplitude = V/Z
= 35 V/176 ohm
= 0.199 A
Resistor voltage = 0.199 A * 150 ohms
= 29.9 V
Inductor voltage = 0.199 A * 92.4 ohms
= 18.4 V
Phase angle =Tan-1 (XL/XR)
= Tan-1( 18.4/29.9)
= 32 degrees
Learn more about impedance:https://brainly.com/question/30475674
#SPJ4
One long wire lies along an x axis and carries a current of 53 A in the positive × direction. A second long wire is perpendicular to the xy plane, passes through the point (0, 4.2 m, 0), and carries a current of 52 A in the positive z direction. What is the magnitude of the
resulting magnetic field at the point (0, 1.4 m, 0)?
The magnitude of the resulting magnetic field at the point (0, 1.4 m, 0) is approximately 8.87 × 10⁻⁶ T.
The magnetic field is a vector quantity and it has both magnitude and direction. The magnetic field is produced due to the moving electric charges, and it can be represented by magnetic field lines. The strength of the magnetic field is represented by the density of magnetic field lines, and the direction of the magnetic field is represented by the orientation of the magnetic field lines. The formula for the magnetic field produced by a current-carrying conductor is given byB = (μ₀/4π) (I₁ L₁) / r₁ ²B = (μ₀/4π) (I₂ L₂) / r₂
whereB is the magnetic field,μ₀ is the permeability of free space, I₁ and I₂ are the currents in the two conductors, L₁ and L₂ are the lengths of the conductors, r₁ and r₂ are the distances between the point where the magnetic field is to be found and the two conductors respectively.Given data:Current in first wire I₁ = 53 A
Current in second wire I₂ = 52 A
Distance from the first wire r₁ = 1.4 m
Distance from the second wire r₂ = 4.2 m
Formula used to find the magnetic field
B = (μ₀/4π) (I₁ L₁) / r₁ ²B = (μ₀/4π) (I₂ L₂) / r₂For the first wire: The wire lies along the x-axis and carries a current of 53 A in the positive × direction. Therefore, I₁ = 53 A, L₁ = ∞ (the wire is infinite), and r₁ = 1.4 m.
So, the magnetic field due to the first wire is,B₁ = (μ₀/4π) (I₁ L₁) / r₁ ²= (4π×10⁻⁷ × 53) / (4π × 1.4²)= (53 × 10⁻⁷) / (1.96)≈ 2.70 × 10⁻⁵ T (approximately)
For the second wire: The wire is perpendicular to the xy plane, passes through the point (0, 4.2 m, 0), and carries a current of 52 A in the positive z direction.
Therefore, I₂ = 52 A, L₂ = ∞, and r₂ = 4.2 m.
So, the magnetic field due to the second wire is,B₂ = (μ₀/4π) (I₂ L₂) / r₂= (4π×10⁻⁷ × 52) / (4π × 4.2)= (52 × 10⁻⁷) / (4.2)≈ 1.24 × 10⁻⁵ T (approximately)
The magnitude of the resulting magnetic field at the point (0, 1.4 m, 0) is the vector sum of B₁ and B₂ at that point and can be calculated as,
B = √(B₁² + B₂²)= √[(2.70 × 10⁻⁵)² + (1.24 × 10⁻⁵)²]= √(7.8735 × 10⁻¹¹)≈ 8.87 × 10⁻⁶ T (approximately)
To know more about magnitude:
https://brainly.com/question/28714281
#SPJ11
Set 1: Gravitation and Planetary Motion NOTE. E Nis "type-writer notation for x10" ( 2 EB - Exam 2x10") you may use either for this class AND the AP GMm mu F GMm 9 G= 6.67 11 Nm /kg F = mg 9 GMm = mg GM 12 т GM V = 1 GM 9 GM V = - 21 T F 9 = mac T 1. A whale shark has a mass of 2.0 E4 kg and the blue whale has a mass of 1.5 E5 kg a. If the two whales are 1.5 m apart, what is the gravitational force between them? b. How does the magnitude of the gravitational force between the two animals compare to the gravitational force between each and the Earth? c. Explain why objects on Earth do not seem to be attracted 2. An asteroid with a mass of 1.5 E21 kg orbits at a distance 4E8 m from a planet with a mass of 6 E24 kg a. Determine the gravitational force on the asteroid. b. Determine the gravitational force on the planet. C Determine the orbital speed of the asteroid. d Determine the time it takes for the asteroid to complete one trip around the planet 3. A 2 2 14 kg comet moves with a velocity of 25 E4 m/s through Space. The mass of the star it is orbiting is 3 E30 kg a Determine the orbital radius of the comet b. Determine the angular momentum of the comet. (assume the comet is very small compared to the star) c An astronomer determines that the orbit is not circular as the comet is observed to reach a maximum distance from the star that is double the distance found in part (a). Using conservation of angular momentum determine the speed of the comet at its farthest position 4. A satellite that rotates around the Earth once every day keeping above the same spot is called a geosynchronous orbit. If the orbit is 3.5 E7 m above the surface of the and the radius and mass of the Earth is about 6.4 E6 m and 6.0 E24 kg respectively. According to the definition of geosynchronous, what is the period of the satellite in hours? seconds? a. Determine the speed of the satellite while in orbit b. Explain satellites could be used to remotely determine the mass of unknown planets 5. Two stars are orbiting each other in a binary star system. The mass of each of the stars is 2 E20 kg and the distance from the stars to the center of their orbit is 1 E7 m. a. Determine the gravitational force between the stars.. b. Determine the orbital speed of each star
In this set of questions, we are exploring the concepts of gravitation and planetary motion. We use the formulas related to gravitational force, orbital speed, and orbital radius to solve various problems.
Firstly, we calculate the gravitational force between two whales and compare it to the gravitational force between each whale and the Earth. Then, we determine the gravitational force on an asteroid and a planet, as well as the orbital speed and time taken for an asteroid to complete one orbit.
Next, we find the orbital radius and angular momentum of a comet orbiting a star, and also calculate the speed of the comet at its farthest position. Finally, we discuss the period of a geosynchronous satellite orbiting the Earth and how satellites can be used to determine the mass of unknown planets.
a. To calculate the gravitational force between the whale shark and the blue whale, we use the formula F = GMm/r^2, where G is the gravitational constant, M and m are the masses of the two objects, and r is the distance between them. Plugging in the values, we find the gravitational force between them.
b. To compare the gravitational force between the two animals and the Earth, we calculate the gravitational force between each animal and the Earth using the same formula.
We observe that the force between the animals is much smaller compared to the force between each animal and the Earth. This is because the mass of the Earth is significantly larger than the mass of the animals, resulting in a stronger gravitational force.
c. Objects on Earth do not seem to be attracted to each other strongly because the gravitational force between them is much weaker compared to the gravitational force between each object and the Earth.
The mass of the Earth is substantially larger than the mass of individual objects on its surface, causing the gravitational force exerted by the Earth to dominate and make the gravitational force between objects on Earth negligible in comparison.
Learn more about satellite click here:
brainly.com/question/28766254
#SPJ11
Driving on a hot day causes tire pressure to rise. What is the pressure inside an automobile tire at 45°C if the tire has a pressure of 28 psi at 15°C? Assume that the
volume and amount of air in the tire remain constant.
Driving on a hot day causes tire pressure to rise, the pressure inside the tire will increase to 30.1 psi.
The pressure of a gas is directly proportional to its temperature. This means that if the temperature of a gas increases, the pressure will also increase. The volume and amount of gas remain constant in this case.
The initial temperature is 15°C and the final temperature is 45°C. The pressure at 15°C is 28 psi. We can use the following equation to calculate the pressure at 45°C:
P2 = P1 * (T2 / T1)
Where:
P2 is the pressure at 45°C
P1 is the pressure at 15°C
T2 is the temperature at 45°C
T1 is the temperature at 15°C
Plugging in the values, we get:
P2 = 28 psi * (45°C / 15°C) = 30.1 psi
Therefore, the pressure inside the tire will increase to 30.1 psi.
To learn more about tire pressure click here; brainly.com/question/24179830
#SPJ11
Four resistors R 1 =78Ω,R 2 =35Ω,R 3 =60Ω and R 4 =42Ω are connected with a battery of voltage 6 V. How much is the total current in the circuit? Express your answer in amperes (A).
The total current in the circuit is 0.028 (A).
To find the total current in the circuit, we can use Ohm's Law and the concept of total resistance in a series circuit. In a series circuit, the total resistance (R_total) is the sum of the individual resistances.
Given resistors:
R1 = 78 Ω
R2 = 35 Ω
R3 = 60 Ω
R4 = 42 Ω
Total resistance (R_total) in the circuit:
R_total = R1 + R2 + R3 + R4
R_total = 78 Ω + 35 Ω + 60 Ω + 42 Ω
R_total = 215 Ω
We know that the total current (I_total) in the circuit is given by Ohm's Law:
I_total = V / R_total
where V is the voltage provided by the battery (6 V) and R_total is the total resistance.
Substituting the given values:
I_total = 6 V / 215 Ω
I_total ≈ 0.028 A
Therefore, the total current in the circuit is approximately 0.028 amperes (A).
To know more about ohm's law refer here: https://brainly.com/question/1247379#
#SPJ11
Gary is interested in the effect of lighting on focus so he tests participants ability to focus on a complex task under three different lighting conditions: bright lighting (M = 10), low lighting (M = 5), neon lighting (M = 4). His results were significant, F(2, 90) = 5.6, p < .05. What can Gary conclude? O a. Bright lights make it easier to focus than low lights or neon lights. O b. Type of lighting has no effect on focus. O c. Bright lights make it more difficult to focus than low lights or neon lights. O d. Type of lighting has some effect on focus.
Based on the given information, Gary conducted an experiment to test the effect of lighting on participants' ability to focus. He compared three different lighting conditions: bright lighting, low lighting, and neon lighting. The results showed a significant effect, with an F-value of 5.6 and p-value less than 0.05. Now we need to determine what Gary can conclude from these results.
The F-value and p-value are indicators of statistical significance in an analysis of variance (ANOVA) test. In this case, the F(2, 90) value suggests that there is a significant difference in participants' ability to focus across the three lighting conditions.
Since the p-value is less than 0.05, Gary can reject the null hypothesis, which states that there is no difference in focus ability between the different lighting conditions. Therefore, he can conclude that the type of lighting does have some effect on focus.
However, the specific nature of the effect cannot be determined solely based on the information provided. The mean values indicate that participants performed best under bright lighting (M = 10), followed by low lighting (M = 5), and neon lighting (M = 4). This suggests that bright lights may make it easier to focus compared to low lights or neon lights, but further analysis or post-hoc tests would be required to provide a more definitive conclusion.
To learn more about Null hypothesis - brainly.com/question/32456224
#SPJ11
In placing a sample on a microscope slide, a glass cover is placed over a water drop on the glass slide. Light incident from above can reflect from the top and bottom of the glass cover and from the glass slide below the water drop. At which surfaces will there be a phase change in the reflected light? Choose all surfaces at
which there will be a phase change in the reflected light. [For clarification: there are five layers to consider here, with four boundary surfaces between adjacent layers: (1) air above the glass cover, (2) the glass cover, (3) the water layer below the glass cover, (4) the
glass slide below the water layer, and (5) air below the glass slide.]
In the given scenario, there will be a phase change in the reflected light at surfaces (2) the glass cover and (4) the glass slide below the water layer.
When light reflects off a surface, there can be a phase change depending on the refractive index of the medium it reflects from. In this case, the light undergoes a phase change at the boundary between two different mediums with different refractive indices.
At surface (2), the light reflects from the top surface of the glass cover. Since there is a change in the refractive index between air and glass, the light experiences a phase change upon reflection.
Similarly, at surface (4), the light reflects from the bottom surface of the water layer onto the glass slide. Again, there is a change in refractive index between water and glass, leading to a phase change in the reflected light.
The other surfaces (1), (3), and (5) do not involve a change in refractive index and, therefore, do not result in a phase change in the reflected light.
Learn more about the refractive index:
https://brainly.com/question/83184
#SPJ11
(a) A sphere made of plastic has a density of 1.14 g/cm3 and a radius of 8.00 cm. It falls through air of density 1.20 kg/m3 and has a drag coefficient of 0.500. What is its terminal speed (in m/s)?
___________m/s
(b) From what height (in m) would the sphere have to be dropped to reach this speed if it fell without air resistance?
___________m
The terminal speed of the sphere is 17.71 m/s. It would have to be dropped from a height of 86.77 m to reach this speed if it fell without air resistance.
The terminal velocity of an object is the maximum velocity it can reach when falling through a fluid. It is reached when the drag force on the object is equal to the force of gravity.
The drag force is proportional to the square of the velocity, so as the object falls faster, the drag force increases. Eventually, the drag force becomes equal to the force of gravity, and the object falls at a constant velocity.
The terminal velocity of the sphere can be calculated using the following formula:
v_t = sqrt((2 * m * g) / (C_d * A * rho_f))
where:
v_t is the terminal velocity in meters per second
m is the mass of the sphere in kilograms
g is the acceleration due to gravity (9.8 m/s^2)
C_d is the drag coefficient (0.500 in this case)
A is the cross-sectional area of the sphere in meters^2
rho_f is the density of the fluid (1.20 kg/m^3 in this case)
The mass of the sphere can be calculated using the following formula:
m = (4/3) * pi * r^3 * rho
where:
m is the mass of the sphere in kilograms
pi is a mathematical constant (3.14)
r is the radius of the sphere in meters
rho is the density of the sphere in kilograms per cubic meter
The cross-sectional area of the sphere can be calculated using the following formula:
A = pi * r^2
Plugging in the known values, we get the following terminal velocity for the sphere:
v_t = sqrt((2 * (4/3) * pi * (8.00 cm)^3 * (1.14 g/cm^3) * 9.8 m/s^2) / (0.500 * pi * (8.00 cm)^2 * 1.20 kg/m^3)) = 17.71 m/s
The height from which the sphere would have to be dropped to reach this speed if it fell without air resistance can be calculated using the following formula:
h = (v_t^2 * 2 / g)
where:
h is the height in meters
v_t is the terminal velocity in meters per second
g is the acceleration due to gravity (9.8 m/s^2)
Plugging in the known values, we get the following height:
h = (17.71 m/s)^2 * 2 / 9.8 m/s^2 = 86.77 m
To learn more about terminal speed click here: brainly.com/question/30556510
#SPJ11
A silver wire has a length of 23.0 m and a resistance of 4.40 at 20.0C. Assuming a circular cross section, what is the wire diameter (in mm)? The reactivity of silver at 10.0 C is 1.59 x 10^-6 omega x m
The diameter of the wire is 0.47 mm.
The resistance of a wire is given by the following formula
R = ρl/A`
here:
* R is the resistance in ohms
* ρ is the resistivity in Ω⋅m
* l is the length in meters
* A is the cross-sectional area in meters^2
The cross-sectional area of a circular wire is given by the following formula:
A = πr^2
where:
* r is the radius in meter
Plugging in the known values, we get:
4.40 Ω = 1.59 × 10^-6 Ω⋅m * 23.0 m / πr^2
r^2 = (4.40 Ω * π) / (1.59 × 10^-6 Ω⋅m * 23.0 m)
r = 0.0089 m
d = 2 * r = 0.0178 m = 0.47 mm
The diameter of the wire is 0.47 mm.
Learn more about diameter with the given link,
https://brainly.com/question/28162977
#SPJ11
If the net charge on the oil drop is negative, what should be
the direction of the electric field that helps it remain
stationary?
Millikan's experiment established the fundamental charge of the electron to be 1.592 x 10-19 coulombs, which is now defined as the elementary charge.
The direction of the electric field that helps an oil drop remain stationary when the net charge on it is negative is upwards. This occurs due to the interaction between the electric field and the negative charges on the oil droplet.
Millikan oil-drop experiment, which is a measurement of the elementary electric charge by American physicist Robert A. Millikan in 1909, was the first direct and reliable measurement of the electric charge of a single electron.
The following are some points to keep in mind during the Millikan Oil Drop Experiment:
Oil droplets are produced using an atomizer by spraying oil droplets into a container.
When oil droplets reach the top, they are visible through a microscope.
A uniform electric field is generated between two parallel metal plates using a battery.
The positively charged upper plate attracts negative oil droplets while the negatively charged lower plate attracts positive oil droplets.
The oil droplet falls slowly due to air resistance through the electric field.
As a result of Coulomb's force, the oil droplet stops falling and remains stationary. The upward electric force balances the downward gravitational force. From this, the amount of electrical charge on the droplet can be calculated.
Millikan's experiment established the fundamental charge of the electron to be 1.592 x 10-19 coulombs, which is now defined as the elementary charge.
To know more about fundamental charge of the electron, visit:
https://brainly.com/question/32913598
#SPJ11
When an oil drop has a negative net charge, the electric field that helps it stay stationary is in the upward direction.
Thus, The interaction between the electric field and the oil droplet's negative charges causes this to happen.
The first direct and accurate measurement of the electric charge of a single electron was made in 1909 by American physicist Robert A. Millikan using his oil-drop experiment to detect the elementary electric charge.
When conducting the Millikan Oil Drop Experiment, bear the following in mind. Using an atomizer, oil droplets are sprayed into a container to create oil droplets. Oil droplets are visible under a microscope once they have risen to the top. Between two people, a consistent electric field is created.
Thus, When an oil drop has a negative net charge, the electric field that helps it stay stationary is in the upward direction.
Learn more about Electric field, refer to the link:
https://brainly.com/question/11482745
#SPJ4
3) Monochromatic light of wavelength =460 nm is incident on a pair of closely spaced slits 0.2 mm apart. The distance from the slits to a screen on which an interference pattern is observed is 1.2m.
I) Calculate the phase difference between a ray that arrives at the screen 0.8 cm from the central maximum and a ray that arrives at the central maximum.
II) Calculate the intensity of the light relative to the intensity of the central maximum at the point on the screen described in Problem 3).
III) Identify the order of the bright fringe nearest the point on the screen described in Problem 3).
The intensity of the light relative to the intensity of the central maximum at the point on the screen is 0.96.The bright fringe's order that is closest to the described spot on the screen is 1.73× 10^-6.
Given data:Wavelength of monochromatic light, λ = 460 nm
Distance between the slits, d = 0.2 mm
Distance from the slits to screen, L = 1.2 m
Distance from the central maximum, x = 0.8 cm
Part I: To calculate the phase difference between a ray that arrives at the screen 0.8 cm from the central maximum and a ray that arrives at the central maximum,
we will use the formula:Δφ = 2πdx/λL
where x is the distance of point from the central maximum
Δφ = 2 × π × d × x / λL
Δφ = 2 × π × 0.2 × 0.008 / 460 × 1.2
Δφ = 2.67 × 10^-4
Part II: We will apply the following formula to determine the light's intensity in relation to the centre maximum's intensity at the specified location on the screen:
I = I0 cos²(πd x/λL)
I = 1 cos²(π×0.2×0.008 / 460×1.2)
I = 0.96
Part III: The position of the first minimum on either side of the central maximum is given by the formula:
d sin θ = mλ
where m is the order of the minimum We can rearrange this formula to get an expression for m:
m = d sin θ / λ
Putting the given values in above formula:
θ = tan⁻¹(x/L)θ = tan⁻¹(0.008 / 1.2)
θ = 0.004 rad
Putting the values of given data in above formula:
m = 0.2 × sin(0.004) / 460 × 10⁻9m = 1.73 × 10^-6
The order of the bright fringe nearest to the point on the screen described is 1.73 × 10^-6.
learn more about intensity from given link
https://brainly.com/question/7068958
#SPJ11