Diameter of the tube = 44.48 mm Pressure of the water at inlet = 70 bar Temperature of the water at inlet = 65°CPressure of the water at the outlet = 50 bar Temperature of the water at the outlet = 700KVelocity of the water = 112.76 m/s
We know that, Volume flow rate = Av Where,A = Cross-sectional area of the tube And,v = Velocity of the water
Therefore,[tex]A = πd²/4[/tex], where d = Diameter of the tube = 44.48 mm = 0.04448 m
Putting the values, [tex]A = π × (0.04448 m)²/4 = 0.00154629 m[/tex]
²Now, we have the values of A and v.
We can calculate the volume flow rate using the formula mentioned above. So,Volume flow rate =
[tex]Av= 0.00154629 m² × 112.76 m/s= 0.1744204754 m³/s[/tex]
We have to convert this volume flow rate from m³/s to L/s.
So,[tex]1 m³/s = 1000 L/s[/tex]
Therefore,[tex]0.1744204754 m³/s = 0.1744204754 × 1000 L/s= 174.4204754 L/s[/tex]
Thus, the inlet volume flow rate is 174.420 L/s, rounded off to 3 decimal places.
To know more about Diameter visit:-
https://brainly.com/question/32968193
#SPJ11
Thermodynamics Consider the ordinary steam plant cycle..And the following data is from that plant: 1. "Boiler outlet and turbine inlet is P=800 psia, T=1400∘F. 2. The outlet of the turbine and condenser inlet is P=40 psia 3.The condenser outlet and the inlet to the pump are at the same pressure as above and at 100% humidity 4. Assume the process in the pump is an adiabatic process Reversible Determine: a.) Heat produced by the boiler, in Btu/lbm b.) Pump work in Btu/lbm c.) Camot thermal efficiency d.) Cycle thermal efficiency e.) T vs s diagram with the saturation curve and all possible values of the cycle
It is made to flow through a turbine to generate work, which is then returned to the condenser, starting the cycle again.
The ordinary steam plant cycle consists of four processes: an adiabatic reversible process in the pump, a constant-pressure heat addition process in the boiler, an adiabatic reversible expansion process in the turbine, and a constant-pressure heat rejection process in the condenser.Thermodynamics deals with the study of heat energy conversion to work energy or vice versa.
The steam plant cycle is one of the most important cycles studied in thermodynamics.In the steam plant cycle, the following data are given:1. P=800 psia, T=1400∘F (Boiler outlet and turbine inlet).2. P=40 psia (The outlet of the turbine and condenser inlet).3. P=40 psia (The condenser outlet and the inlet to the pump are at the same pressure as above and at 100% humidity).4. An adiabatic process in the pump is assumed to be reversible. The process of solving this problem involves calculating various parameters of the steam plant cycle, such as heat produced by the boiler, pump work, Camot thermal efficiency, cycle thermal efficiency, T vs s diagram with the saturation curve, and all possible values of the cycle.Heat produced by the boiler:q_b = h_3 - h_2
Pump work:W_p = h_4 - h_3Camot thermal efficiency:η_C = 1 - T_1/T_3Cycle thermal efficiency:η = (W_net)/q_in = (W_t - W_p)/q_inT vs s diagram with the saturation curve and all possible values of the cycle:In this cycle, the steam is condensed by cooling the working fluid in the condenser. The working fluid is then pumped to the boiler by the feedwater pump. The water is then heated to a high temperature in the boiler. Then, it is made to flow through a turbine to generate work, which is then returned to the condenser, starting the cycle again.
Learn more about condenser :
https://brainly.com/question/32084530
#SPJ11
Q1: (30 Marks) An NMOS transistor has K = 200 μA/V². What is the value of Kn if W= 60 µm, L=3 μm? If W=3 µm, L=0.15 µm? If W = 10 µm, L=0.25 µm?
Kn is the transconductance parameter of a MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor). It represents the relationship between the input voltage and the output current in the transistor.
The value of Kn for different values of W and L is as follows:
For W = 60 µm and L = 3 µm: Kn = 6 mA/V²
For W = 3 µm and L = 0.15 µm: Kn = 0.12 mA/V²
For W = 10 µm and L = 0.25 µm: Kn = 0.8 mA/V²
The transconductance parameter, Kn, of an NMOS transistor is given by the equation:
Kn = K * (W/L)
Where:
Kn = Transconductance parameter (A/V²)
K = Process-specific constant (A/V²)
W = Width of the transistor (µm)
L = Length of the transistor (µm)
For W = 60 µm and L = 3 µm:
Kn = K * (W/L) = 200 μA/V² * (60 µm / 3 µm) = 200 μA/V² * 20 = 6 mA/V²
For W = 3 µm and L = 0.15 µm:
Kn = K * (W/L) = 200 μA/V² * (3 µm / 0.15 µm) = 200 μA/V² * 20 = 0.12 mA/V²
For W = 10 µm and L = 0.25 µm:
Kn = K * (W/L) = 200 μA/V² * (10 µm / 0.25 µm) = 200 μA/V² * 40 = 0.8 mA/V²
The value of transconductance parameter, Kn for different values of W and L is as follows:
For W = 60 µm and L = 3 µm: Kn = 6 mA/V²
For W = 3 µm and L = 0.15 µm: Kn = 0.12 mA/V²
For W = 10 µm and L = 0.25 µm: Kn = 0.8 mA/V²
To know more about transconductance, visit;
https://brainly.com/question/32196152
#SPJ11
Create a 5 by 5 matrix of random integers in the range from 5 to 15, save the matrix into a data file, load the data file into the command window, add a row of ones to bottom of the matrix, and save the matrix back in the data file.
Here's the solution to the given problem:We will begin by creating a 5x5 matrix with random integers in the range from 5 to 15. The code is given below:mat = randi([5,15],5,5);Now, we will save the above matrix in a data file. The following command can be used for the same:save('matrixData.mat', 'mat');Here, 'matrixData.
mat' is the name of the file and 'mat' is the name of the matrix that we want to save in the file.Now, we will load the saved matrix data file in the command window. We will use the following command for the same:load('matrixData.mat');The above command will load the saved data file into the workspace.Now, we will add a row of ones to the bottom of the matrix.
For this, we will use the following command:mat = [mat; ones(1,size(mat,2))];
Here, we are creating a row of ones with the same number of columns as the matrix and appending it to the bottom of the matrix.Finally, we will save the updated matrix back in the data file using the following command:save('matrixData.mat', 'mat');
This will save the updated matrix in the same data file 'matrixData.mat'.
To know more about matrix visit:
https://brainly.com/question/29000721
#SPJ11
An object of mass 5 kg is moving with an initial velocity of 10 ms. A constant force acts on if for 4.5 giving it a speed of 2mys in the opposite direction. What is the acceferation, in ms?? a. −1.5
b. −30
c. −5.0
d. −7.5
e. 0.55
To find the acceleration of the object, we can use the equation: a = (vf - vi) / t. Therefore, the acceleration of the object is approximately -2.67 m/s².
where:
a is the acceleration,
vf is the final velocity,
vi is the initial velocity, and
t is the time.
Given:
Mass of the object (m) = 5 kg
Initial velocity (vi) = 10 m/s
Final velocity (vf) = -2 m/s (since it is in the opposite direction)
Time (t) = 4.5 s
Substituting the values into the equation, we can calculate the acceleration:
a = (-2 m/s - 10 m/s) / 4.5 s
= (-12 m/s) / 4.5 s
= -2.67 m/s²
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ4
A gear train system is to be used to drive a square thread screw to lift a load of 20 kN (under Earth gravitational influence) that will travel within 0.9 to 1.25 m/s. Assume that the length of the power screw is infinite and 100% power from the final driven gear is transferred to the power screw. The linear displacement per turn on power screw is at 20 mm per turn. Meanwhile, on the gear system, the driver is rotating at 4500 rpm counter-clockwise and has 15 teeth and Pd of 16. The gear attached to at the square thread has 20 teeth and Pd of 20. The configuration of the machine is shown below. a) Solve the torque required to raise and lower the load and the speed on the final driven gear attached on the square power screw. b) Construct this gear train by using several idler gears (must be more than 4 gears) with any gear tooth size. The distance between the driver gear and final driver gear must be not more that 1250mm. Prove your design by showing appropriate calculation. c) Assume that the loss of torque and power is 12% and 15% respectively on each gear addition to the previous powered gear, calculate the torque and power needed at the driver gear to lift the load on the square thread screw. d) If the machine operated on the Moon's surface, calculate the speed range of the load lifted presuming the value of torque and power in (b) if the gear train configuration in (c) is maintained. (Moon's gravity is 1/6 of Earth's gravity)
To solve this problem, we need to determine the torque required to raise and lower the load, as well as the speed of the final driven gear attached to the square power screw.
To solve part (a), we can calculate the torque required to raise and lower the load by considering the load force, power screw characteristics, and gear ratios. The speed of the final driven gear can be determined based on the linear displacement per turn of the power screw and the rotational speed of the driver gear. For part (b), we need to design a gear train system using several idler gears that meet the distance requirement. We can choose appropriate gear tooth sizes for the idler gears to achieve the desired gear ratios.
In part (c), we need to calculate the torque and power needed at the driver gear, taking into account the losses in torque and power for each gear addition. We can apply the given percentage losses to determine the adjusted torque and power requirements. Finally, in part (d), we can calculate the speed range of the load when operated on the Moon's surface by adjusting the gravitational force and using the gear train configuration and torque values from part (c).
By performing the necessary calculations and considering the given parameters, we can determine the torque, power, and speed requirements for the gear train system and analyze its performance under different conditions.
Learn more about torque from here:
https://brainly.com/question/30338175
#SPJ11
The lattice constant of a unit cell of a FCC metal is 4.93 x 10-7mm.
(i) Calculate the planar atomic density for planes (110) and (111) in the metal, and
(ii) Determine the family of planes that constitute slip system in FCC metals with reference to the two plane in (d) (i) above.
The planar atomic densities for the (110) and (111) planes in the FCC metal are 1.62 × [tex]10^{13}[/tex] [tex]$$m^{-2}[/tex] and 2.43 × [tex]10^{13} $ m^{-2}[/tex] respectively. The slip system consists of the {111} and {110} planes
The general formula to determine the planar atomic density (P) for a cubic crystal system is given by:P = n * Z / a², Where,
n = number of atoms in a unit cellZ = number of atoms on the given planea = lattice constantLet's find P for the planes (110) and (111) in the metal(i) P for (110) plane:From the Miller indices of the given plane (110), we can determine its interplanar spacing as follows:
d₁₁₀ = a / √2
P for the given plane can now be determined as:
P₁₁₀ = n x Z / d₁₁₀² X a= 4 x 2 / (a/√2)² x a= 4 x 2 / a²/2 x a= 8 / aP₁₁₀ = 8 / 4.93 x 10⁻⁷ = 1.62 × 10¹³ m⁻²
(ii) P for (111) plane: From the Miller indices of the given plane (111), we can determine its interplanar spacing as follows:
d₁₁₁ = a / √3
P for the given plane can now be determined as:
P₁₁₁ = n x Z / d₁₁₁² x a= 4 x 3 / (a/√3)² x a= 12 / a²P₁₁₁ = 12 / 4.93 x 10⁻⁷ = 2.43 × 10¹³ m⁻²
The family of planes that constitutes a slip system in FCC metals with reference to the two planes (110) and (111) can be determined by the Schmid's Law. Schmid's Law is given by:
τ = σ.sinφ.cosλ, Where,
τ = resolved shear stressσ = applied tensile stressφ = angle between the tensile axis and the slip planeλ = angle between the tensile axis and the slip directionFor an FCC metal, the resolved shear stress for the given planes can be determined using the following equation:
τ = σ / (2√3), Where, σ = applied tensile stressFor the (110) plane, the slip direction is the [111] direction (maximum dense packed direction). So, λ = 45° and φ = 35.26°.
Putting the values in Schmid's Law, we get:
sin φ = sin 35.26° = 0.574cos λ = cos 45° = 0.707τ = σ / (2√3) = 0.288 σSimilarly, for the (111) plane, the slip direction is the [110] direction. So, λ = 45° and φ = 54.74°.
Putting the values in Schmid's Law, we get:
sin φ = sin 54.74° = 0.819cos λ = cos 45° = 0.707τ = σ / (2√3) = 0.288 σ. Hence, the family of planes that constitutes a slip system in FCC metals with reference to the two planes (110) and (111) is {111} and {110} respectively.
Learn more about planar atomic: brainly.com/question/30907620
#SPJ11
Air in a closed piston cylinder device is initially at 1200 K and at 100 kPa. The air undergoes a process until its pressure is 2.3 MPa. The final temperature of the air is 1800 K In your assessment of the following do not assume constant specific heats. What is the change in the air's specific entropy during this process (kJ/kgk)? Chose the correct answer from the list below. If none of the values provided are within 5% of the correct answer, or if the question is unanswerable, indicate this choice instead. O a. -0.410 kJ/kgk O b. The question is unanswerable / missing information O C -0.437 kJ/kgk O d. None of these are within 5% of the correct solution O e. 0.250 kJ/kgk O f. 0.410 kJ/kgK O g. 0.492 kJ/kgK O h. -0.492 kJ/kgk O i. 0.437 kJ/kgK
The specific entropy change cannot be determined without information about the temperature-dependent specific heat. Therefore, the question is unanswerable/missing information (option b).
To determine the change in specific entropy during the process, we can use the thermodynamic property relations. The change in specific entropy (Δs) can be calculated using the following equation:
Δs = ∫(Cp/T)dT – Rln(P2/P1)
Where Cp is the specific heat at constant pressure, T is the temperature, R is the specific gas constant, P2 is the final pressure, and P1 is the initial pressure.
Since the problem statement mentions not to assume constant specific heats, we need to account for the temperature-dependent specific heat. Unfortunately, without information about the temperature variation of the specific heat, we cannot accurately calculate the change in specific entropy. Therefore, the correct answer is b. The question is unanswerable/missing information.
Learn more about Specific entropy here: brainly.com/question/31966522
#SPJ11
During an experiment in a section narrowing
transversal, the fluid mechanics students found that the analogue pressure gauge M was not working well. To test the veracity of the data measured by the manometer, the students decided to elaborate an equation
where the variable monitored by the manometer is a function of the diameter d, of the flow Q, of the heights h1 and h2 of the manometer in U and the relative density of the gauge fluid. show what is this equation.
The equation relating the variable monitored by the manometer to the diameter, flow rate, manometer heights, and relative density of the gauge fluid is: Variable = f(d, Q, h1, h2, ρ).
In fluid mechanics, a manometer is used to measure pressure differences in a fluid system. However, if the analogue pressure gauge (referred to as gauge M) is not functioning properly, the data it provides may be inaccurate. To verify the accuracy of the measured data, the students decided to establish an equation that expresses the variable monitored by the manometer as a function of various parameters.
The equation, Variable = f(d, Q, h1, h2, ρ), represents the relationship between the variable being monitored (which is not specified in the question), the diameter of the section narrowing transversal (d), the flow rate (Q), the heights h1 and h2 of the manometer in a U-shaped tube, and the relative density of the gauge fluid (ρ). This equation allows the students to calculate or predict the value of the variable based on the known values of the other parameters.
The diameter of the section narrowing transversal affects the flow characteristics of the fluid, and therefore, it can impact the pressure measurements obtained by the manometer. Similarly, the flow rate, heights h1 and h2, and the relative density of the gauge fluid all play crucial roles in determining the pressure difference sensed by the manometer.
By formulating this equation, the students can analyze the relationship between these parameters and the monitored variable, enabling them to assess the accuracy and reliability of the manometer's measurements. This equation serves as a tool for verifying the data obtained from the manometer and ensuring the validity of their experimental results.
Learn more about Fluid mechanics
brainly.com/question/12977983
#SPJ11
(Place name, course and date on all sheets to be e- mailed especially the file title.) 1. A dummy strain gauge is used to compensate for: a). lack of sensitivity b). variations in temperature c), all of the above 2. The null balance condition of the Wheatstone Bridge assures: a). that no currents a flowing in the vertical bridge legs b). that the Galvanometer is at highest sensitivity c). horizontal bridge leg has no current 3. The Kirchhoff Current Law applies to: a). only non-planar circuits b). only planar circuits c), both planar and non-planar circuits 4. The initial step in using the Node-Voltage method is a). to find the dependent essential nodes b). to find the clockwise the essential meshes c), to find the independent essential nodes 5. The individual credited with developing a computer program in the year 1840-was: a). Dr. Katherine Johnson b). Lady Ada Lovelace c). Mrs. Hedy Lamar 6. A major contributor to Edison's light bulb, by virtue of assistance with filment technology was: a). Elias Howe b). Elijah McCoy c). Louis Latimer
When e mailing the sheets, it is important to include the place name, course, and date in the file title to ensure that the content is loaded. The following are the answers to the questions provided:
1. A dummy strain gauge is used to compensate for c) all of the above, i.e., lack of sensitivity, variations in temperature.
2. The null balance condition of the Wheatstone Bridge assures that the horizontal bridge leg has no current flowing in it.
3. The Kirchhoff Current Law applies to both planar and non-planar circuits.
4. The initial step in using the Node-Voltage method is to find the independent essential nodes.
5. Lady Ada Lovelace is credited with developing a computer program in the year 1840.
6. Louis Latimer was a major contributor to Edison's light bulb by assisting with filament technology.
To know more about e mailing visit:
https://brainly.com/question/30159736
#SPJ11
Implementation of the quadcopter model in Matlab (for example a
state-space model or transfer matrix one), simulation results (step
responses).
The quadcopter is an aerial vehicle that has gained a lot of attention and interest in recent times due to its application in different fields. It has different flight controls, including lift, pitch, roll, and yaw, which make it versatile and efficient.
The implementation of a quadcopter model in Matlab involves the creation of a mathematical representation of the system that simulates the flight behavior of the quadcopter.The state-space model or transfer matrix is the common representation used to simulate the quadcopter's dynamics. The state-space model represents the quadcopter's states in the form of differential equations that describe how the system changes over time.
The quadcopter model's implementation involves the following steps:
1. Define the system inputs and outputs: The system inputs are the control signals, while the outputs are the states of the system.
2. Develop the mathematical model: This involves deriving the equations that represent the quadcopter's dynamics.
3. Linearize the system: The quadcopter model is a nonlinear system, and linearizing it simplifies its dynamics and makes it easier to simulate.
4. Create the state-space model or transfer matrix: Using the derived equations, the state-space model or transfer matrix is created.
5. Simulate the system: The created model is used to simulate the system's response to different inputs, including step responses. The simulation results help to analyze and evaluate the quadcopter's behavior and performance.
To know more about quadcopter visit:
https://brainly.com/question/15322532
#SPJ11
Which of the following is an example of a prismatic pair? O Ball and socket joint O Piston and cylinder of a reciprocating engine O Nut and screw O Shaft and collar where the axial movement of the collar is restricted
A prismatic pair is a type of kinematic pair in which two surfaces of the two links in a machine are in sliding contact. The sliding surface of one link is flat, while the sliding surface of the other link is flat and parallel to a line of motion.
A prismatic pair is a sliding pair that restricts motion in one direction (along its axis). Hence, among the given options, the shaft and collar where the axial movement of the collar is restricted is an example of a prismatic pair. The other options mentioned are different types of pairs, for example, ball and socket joint is an example of a spherical pair where the motion of the link in one degree of freedom is unrestricted.
Similarly, piston and cylinder of a reciprocating engine is an example of a cylindrical pair where the motion of the link in two degrees of freedom is unrestricted.Nut and screw are examples of a screw pair where the motion of the link in one degree of freedom is restricted.
To know more about reciprocating engine visit :
https://brainly.com/question/18833025
#SPJ11
1. Write the characteristics of Ideal op amp and Practical op Amp
4. Design a circuit using op amp that would produce an output equal to 1/3 rd of the sum of the input voltages or vout=-1/3(v1+v2+v3+v4)
5. Derive the expression for the gain of amn Inverting and Non-Inverting Amplifier
1. Ideal Op-Amp characteristics and Practical Op-Amp characteristicsIdeal op-amp characteristics:1. Infinite open-loop gain (A).
2. Infinite input impedance (Rin).
3. Zero output impedance (Rout).
4. Infinite bandwidth.
5. Infinite common-mode rejection ratio (CMRR).
6. Zero offset voltage (Vos).
7. Infinite slew rate.
8. Zero noise.
Practical Op-Amp characteristics:
1. Finite open-loop gain (A).
2. Finite input impedance (Rin).
3. Non-zero output impedance (Rout).
4. Finite bandwidth.
5. Non-zero common-mode rejection ratio (CMRR).
6. Non-zero offset voltage (Vos).
7. Finite slew rate.
8. Non-zero noise.
4. Op-Amp Circuit to generate Vout=-1/3(V1+V2+V3+V4)The circuit is shown below:In this circuit, all four input voltages (V1 to V4) are connected to the op-amp's inverting input (-).The non-inverting input (+) is linked to the ground through resistor R1. R2 and R3 are linked in series between the output and the inverting input.
5. Gain Expression of an Inverting Amplifier and Non-Inverting AmplifierThe following are the gain expressions for inverting and non-inverting amplifiers:Gain of an inverting amplifier: Av = - Rf/RiGain of a non-inverting amplifier: Av = 1 + Rf/RiWhere,Rf = Feedback resistorRi = Input resistor
These are the characteristics of Ideal op-amp and Practical op-amp, design of a circuit using op-amp that would produce an output equal to 1/3rd of the sum of the input voltages and derivation of expression for the gain of an Inverting and Non-Inverting Amplifier.
To know about Circuit visit:
https://brainly.com/question/12608516
#SPJ11
A 100 cm diameter steel tank of 150 cm height and 0.5 cm thickness is used to store Sulfuric Acid. The level of Sulfuric Acid is typically maintained at 2/3rd the height of the tank. After the tank was brought into operation, leakage developed after just one year. The failure analysis engineer ran a potentiodynamic scan on a specimen made from the same material in the same strength sulfuric acid and determined that the corrosion current density would be 4.5 X 104 Amps/cm². a) Did the leak developed because of general (uniform) corrosion? b) If yes, what remedies you suggest in future tank design to prevent leakage If no, what other cause(s) you suspect for the leakage. Assume that the quality of steel was as specified, and the cathodic reaction is hydrogen reduction 2H+ + 2e → H₂ and the anodic reaction is Fe → Fe +² +2e The Atomic weight of Fe is 55.85 gms/mol; Density of Fe is 7.87 gms/cm³ You can approximate the Faraday constant to be 96,500 Coulombs/mol.
A 100 cm diameter steel tank of 150 cm height and 0.5 cm thickness is used to store Sulfuric Acid, the corrosion rate is 3.68 x [tex]10^{(-6)[/tex] g/(cm²·s).
We must compare the corrosion rate with the anticipated tank lifespan in order to ascertain whether the leak originated from general (uniform) corrosion.
a) Corrosion Rate Calculation:
The corrosion current density (i_corr) is given as [tex]4.5 * 10^{(-4)[/tex] Amps/cm². Using Faraday's law of electrolysis, we can calculate the corrosion rate (CR):
CR = (i_corr * M) / (n * F * ρ)
CR = (4.5 x [tex]10^{(-4)[/tex] * 55.85) / (2 * 96500 * 7.87)
CR ≈ 3.68 x [tex]10^{(-6)[/tex] g/(cm²·s)
b) Comparison with estimated Lifetime: We must take into account the remaining wall thickness (t_remaining) after one year of operation to see if the tank's estimated lifetime is much longer than the corrosion rate.
The formula is as follows:
t_remaining = t_initial - CR * t_operation
t_remaining = 0.5 - (3.68 x 10^(-6) * 31,536,000)
t_remaining ≈ 0.5 - 0.1158
t_remaining ≈ 0.3842 cm
The fact that the residual wall thickness is still greater than zero shows that general corrosion is not the only cause of the leak.
Localised Corrosion: Localised corrosion mechanisms including pitting or crevice corrosion are likely to blame for the leakage.
These types of corrosion might start at particular locations, causing localised damage that results in leaking.
Several steps can be taken into consideration in order to stop leakage in upcoming tank designs:
Utilise materials resistant to corrosion.Defending Coatings.Cathodic Defence.Inspection and upkeep on a regular basis.Thus, the corrosion rate is 3.68 x [tex]10^{(-6)[/tex] g/(cm²·s).
For more details regarding corrosion rate, visit:
https://brainly.com/question/29697991
#SPJ4
This question concerns Enterprise and Strategy in High Tech Ventures. There are many generalised types of new venture typologies. Each has implications for how you go about finding a business idea and developing an enterprise strategy. Briefly describe the main features of one new venture typology, namely "Incremental Product Innovation".
Incremental Product Innovation is one of the most common types of new venture typologies. Incremental Product Innovation is concerned with improving current products or developing new products by enhancing their design, performance, and functionality while keeping them within the existing market segment or extending them to adjacent markets.
It means a company will take an existing product and make minor modifications or improvements to create a new one that's still within the same market. The incremental product innovation model is often used in mature markets where competition is fierce, and companies are always looking for ways to stay ahead of their competitors.
This model helps companies achieve a competitive advantage by offering improved products to existing customers. It is less risky than other new venture typologies as it leverages existing products and the knowledge base of the company.
To know more about Innovation visit:
https://brainly.com/question/30929075
#SPJ11
Steam enters the high-pressure turbine of a steam power plant that operates on the ideal reheat Rankine cycle at 6 MPa and 500°C and leaves as saturated vapor. Steam is then reheated to 400°C before it expands to a pressure of 10 kPa. Heat is transferred to the steam in the boiler at a rate of 6 × 104 kW. Steam is cooled in the condenser by the cooling water from a nearby river, which enters the condenser at 7°C. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the pressure at which reheating takes place, (b) the net power output and thermal efficiency, and (c) the minimum mass flow rate of the cooling water required. mains the same
a) Pressure at which reheating takes place The given steam power plant operates on the ideal reheat Rankine cycle. Steam enters the high-pressure turbine at 6 MPa and 500°C and leaves as saturated vapor.
The cycle on a T-s diagram with respect to saturation lines can be represented as shown below :From the above diagram, it can be observed that the steam is reheated between 6 MPa and 10 kPa. Therefore, the pressure at which reheating takes place is 10 kPa .
b) Net power output and thermal efficiency The net power output of the steam power plant can be given as follows: Net Power output = Work done by the turbine – Work done by the pump Work done by the turbine = h3 - h4Work done by the pump = h2 - h1Net Power output = h3 - h4 - (h2 - h1)Thermal efficiency of the steam power plant can be given as follows: Thermal Efficiency = (Net Power Output / Heat Supplied) x 100Heat supplied =[tex]6 × 104 kW = Q1 + Q2 + Q3h1 = hf (7°C) = 5.204 kJ/kgh2 = hf (10 kPa) = 191.81 kJ/kgh3 = hg (6 MPa) = 3072.2 kJ/kgh4 = hf (400°C) = 2676.3 kJ/kgQ1 = m(h3 - h2) = m(3072.2 - 191.81) = 2880.39m kJ/kgQ2 = m(h4 - h1) = m(26762880.39m - 2671.09m = 209.3m x 100= [209.3m / (2880.39m + 2671.09m)] x 100= 6.4 %c)[/tex]
Minimum mass flow rate of the cooling water required Heat rejected by the steam to the cooling water can be given as follows: Q rejected = mCpΔTwhere m is the mass flow rate of cooling water, Cp is the specific heat capacity of water, and ΔT is the temperature difference .Qrejected = Q1 - Q2 - Q3 = 209.3 m kW Q rejected = m Cp (T2 - T1)where T2 = temperature of water leaving the condenser = 37°C, T1 = temperature of water entering the condenser = 7°C, and Cp = 4.18 kJ/kg K Therefore, m = Qrejected / (Cp (T2 - T1))= 209.3 x 103 / (4.18 x 30)= 1.59 x 103 kg/s = 1590 kg/s Thus, the minimum mass flow rate of cooling water required is 1590 kg/s.
To know more about saturated vapor visit:
brainly.com/question/32499566
#SPJ11
8. Newton's law for the shear stress is a relationship between a) Pressure, velocity and temperature b) Shear stress and velocity c) Shear stress and the shear strain rate d) Rate of shear strain and temperature 9. A liquid compressed in cylinder has an initial volume of 0.04 m² at 50 kg/cm' and a volume of 0.039 m² at 150 kg/em' after compression. The bulk modulus of elasticity of liquid is a) 4000 kg/cm² b) 400 kg/cm² c) 40 × 10³ kg/cm² d) 4 x 10 kg/cm² 10. In a static fluid a) Resistance to shear stress is small b) Fluid pressure is zero c) Linear deformation is small d) Only normal stresses can exist 11. Liquids transmit pressure equally in all the directions. This is according to a) Boyle's law b) Archimedes principle c) Pascal's law d) Newton's formula e) Chezy's equation 12. When an open tank containing liquid moves with an acceleration in the horizontal direction, then the free surface of the liquid a) Remains horizontal b) Becomes curved c) Falls down on the front wall d) Falls down on the back wall 13. When a body is immersed wholly or partially in a liquid, it is lifted up by a force equal to the weight of liquid displaced by the body. This statement is called a) Pascal's law b) Archimedes's principle c) Principle of flotation d) Bernoulli's theorem 14. An ideal liquid a) has constant viscosity b) has zero viscosity c) is compressible d) none of the above. 15. Units of surface tension are a) J/m² b) N/kg c) N/m² d) it is dimensionless 16. The correct formula for Euler's equation of hydrostatics is DE = a) a-gradp = 0 b) a-gradp = const c) à-gradp- Dt 17. The force acting on inclined submerged area is a) F = pgh,A b) F = pgh,A c) F = pgx,A d) F = pgx,A
The correct answers for the fluid mechanics problems are:
(c) Shear stress and the shear strain rate.
(a) 4000 kg/cm².
(b) Fluid pressure is zero.
(c) Pascal's law.
(a) Remains horizontal.
(b) Archimedes's principle.
b) has zero viscosity
(c) N/m².
∇·p = g
(b) F = pg[tex]h_{p}[/tex]A
How to interpret Fluid mechanics?8) Newton's law for the shear stress states that the shear stress is directly proportional to the velocity gradient.
Thus, Newton's law for the shear stress is a relationship between c) Shear stress and the shear strain rate .
9) Formula for Bulk modulus here is:
Bulk modulus =∆p/(∆v/v)
Thus:
∆p = 150 - 50 = 100 kg/m²
∆v = 0.040 - 0.039 = 0.001
Bulk modulus = 100/(0.001/0.040)
= 4000kg/cm²
10) In a static fluid, it means no motion as it is at rest and as such the fluid pressure is zero.
11) Pascal's law says that pressure applied to an enclosed fluid will be transmitted without a change in magnitude to every point of the fluid and to the walls of the container.
12) When an open tank containing liquid moves with an acceleration in the horizontal direction, then the free surface of the liquid a) Remains horizontal
13) When a body is immersed wholly or partially in a liquid, it is lifted up by a force equal to the weight of liquid displaced by the body. This statement is called b) Archimedes's principle
14) An ideal fluid is a fluid that is incompressible and no internal resistance to flow (zero viscosity)
15) Surface tension is also called Pressure or Force over the area. Thus:
The unit of surface tension is c) N/m²
16) The correct formula for Euler's equation of hydrostatics is:
∇p = ρg
17) The force acting on inclined submerged area is:
F = pg[tex]h_{p}[/tex]A
Read more about Fluid Mechanics at: https://brainly.com/question/31174575
#SPJ4
Calculate the weight fraction of mullite that is pro eutectic in a slowly cooled 30 mol % Al2O3 70 mol % SiO2 refractory cooled to room temperature.
The weight fraction of pro eutectic mullite is 100%.
To calculate the weight fraction of pro eutectic mullite in the refractory material, we need to consider the phase diagram of the Al2O3-SiO2 system.
In a slowly cooled refractory with 30 mol% Al2O3 and 70 mol% SiO2, the eutectic composition occurs at approximately 50 mol% Al2O3 and 50 mol% SiO2.
Below this composition, mullite is the primary phase, and above it, corundum (Al2O3) is the primary phase.
Since the composition of the refractory is below the eutectic composition, we can assume that the entire refractory consists of mullite. Therefore, the weight fraction of pro eutectic mullite is 100%.
It's important to note that the weight fraction of mullite could change if the refractory was cooled under different conditions or if impurities were present.
However, based on the given information of a slowly cooled refractory with the specified composition, the weight fraction of pro eutectic mullite is 100%.
For more such questions on mullite,click on
https://brainly.com/question/19551606
#SPJ8
How is current sensing achieved for small motors and large
motors
Electric motors are used in numerous applications, from toys and household appliances to large industrial machinery and automotive systems. They convert electrical energy into mechanical energy, making them an essential part of most mechanical devices. Current sensing is a crucial aspect of motor control, as it enables operators to monitor and adjust the motor's performance as necessary.
What is current sensing?
Current sensing is the process of measuring the electrical current flowing through a conductor, such as a wire or cable. It is a critical function for a variety of applications, including electric motor control.
Current sensors can be used to measure either AC or DC currents, and they come in a variety of shapes and sizes. They are frequently employed in motor control systems to monitor the motor's current and ensure that it is operating correctly.
The following are two ways current sensing is achieved for small and large motors:
1. Small Motors Current sensing in small motors is frequently accomplished by using a low-value sense resistor. A sense resistor is placed in the current path, and a voltage proportional to the current flowing through the motor is generated across it.
This voltage is then amplified and fed back to the control system to enable it to adjust the motor's current as necessary.
2. Large Motors Current sensing in large motors can be more difficult than in small motors because the current levels involved can be quite high.
Current transformers are frequently employed in large motors to measure the current flowing through the motor. A current transformer consists of a magnetic core and a winding.
The current flowing through the motor produces a magnetic field that is sensed by the transformer's winding, generating a voltage proportional to the current. This voltage is then amplified and used to regulate the motor's current as required.
In summary, current sensing is a critical aspect of electric motor control, allowing operators to monitor and adjust the motor's performance as required.
For small motors, a low-value sense resistor is frequently employed, while for large motors, a current transformer is commonly used.
to know more about current sensing visit:
https://brainly.com/question/13666989
#SPJ11
What is the main role of governors and what are they used for?
which is the main force acting on the governer to make it
function, descibe the mechanism?
write 2-3 sentences for each question
Governors are used to control the speed of engines and maintain them at a steady speed under varying conditions of load. By sensing the engine speed, the governor adjusts the fuel flow to keep the speed constant.
The main force acting on the governor to make it function is the centrifugal force.
The main role of governors and what they are used for
Governors are a mechanical device used to control the speed of engines in heavy equipment or machinery. The governor's purpose is to keep the speed of the engine constant under changing load conditions. The main role of governors is to maintain the speed of an engine when the load or resistance changes.
Conclusion: Governors are used to control the speed of engines and maintain them at a steady speed under varying conditions of load. By sensing the engine speed, the governor adjusts the fuel flow to keep the speed constant.
The main force acting on the governor to make it function.
The centrifugal force is the main force acting on the governor to make it function. The governor is equipped with a flyweight assembly, which is connected to the engine's output shaft. The centrifugal force generated by the flyweights causes them to move outwards.
Explanation: When the engine runs at its rated speed, the governor's flyweights move outward, causing the governor's control linkage to hold a constant fuel supply to the engine. If the engine speed rises due to an increase in load, the governor's flyweights move out, pushing the control linkage inward and reducing the fuel supply to the engine.
The flyweights move inward when the engine slows down, reducing the centrifugal force and pushing the control linkage out, increasing the fuel supply to the engine to maintain the speed.
To know more about engines visit
https://brainly.com/question/22453852
#SPJ11
1. Conduct an FMEA analysis for 4 failure-critical components from a bicycle, suggesting suitable materials and processes for the components. (12 Marks)
2.Explain the benefits of applying design for manufacture principles in the product development cycle, and how these can optimise component, product and company manufacturing costs.
3.Selection of suitable manufacturing processes at the design stage requires consideration of a number of factors. Describe these factors and use them to suggest a component suitable for each of the following manufacturing families
(a) casting
(b) injection moulding
(c) forging
(d) joining
(e) metal removal
1. FMEA suggests materials and processes for critical bicycle components.
2. Design for manufacture optimizes costs, quality, and scalability.
3. Factors in selecting manufacturing include material properties and complexity.
1. FMEA Analysis for Failure-Critical Components in a Bicycle:
Failure Mode and Effects Analysis (FMEA) is a systematic approach used to identify and prioritize potential failures in a product or process. Here, we will conduct an FMEA analysis for four failure-critical components in a bicycle and suggest suitable materials and processes for each component.
Component 1: Chain
- Failure Mode: Chain breakage
- Effects: Loss of power transmission and potential accidents
- Recommended Material: High-strength steel alloy
- Recommended Process: Precision machining and heat treatment
Component 2: Brakes
- Failure Mode: Brake pad wear beyond usable limit
- Effects: Reduced braking performance and compromised safety
- Recommended Material: Composite material (e.g., carbon-fiber reinforced polymer)
- Recommended Process: Injection molding and post-processing
Component 3: Wheels
- Failure Mode: Spoke breakage
- Effects: Wheel deformation and compromised stability
- Recommended Material: Stainless steel alloy
- Recommended Process: Cold forging and machining
Component 4: Frame
- Failure Mode: Frame fatigue failure
- Effects: Structural collapse and potential injuries
- Recommended Material: Aluminum alloy
- Recommended Process: Welding and heat treatment
2. Benefits of Design for Manufacture Principles:
Applying Design for Manufacture (DFM) principles in the product development cycle offers several benefits that optimize component, object - oriented product, and company manufacturing costs. Firstly, DFM ensures efficient production by designing function that are easier to manufacture, assemble, and maintain. This reduces manufacturing time and costs.
Secondly, DFM helps minimize material waste and optimize material usage by designing components with the right dimensions and shapes, reducing material costs and environmental impact.
Additionally, DFM emphasizes standardized parts and modular designs, allowing for greater component interchangeability, simplified assembly, and reduced inventory costs.
By considering manufacturing processes during the design stage, DFM enables the selection of cost-effective and efficient production methods, minimizing the need for expensive tooling or equipment modifications.
Ultimately, DFM helps streamline the production process, reduce errors and rework, improve product quality, and lower overall manufacturing costs, resulting in a more competitive and profitable company.
3. Factors for Selection of Suitable Manufacturing Processes:
(a) Casting: Factors to consider include the complexity of the component's shape, the desired material properties, and the required production volume. Suitable component: Engine cylinder block for an automobile.
(b) Injection Moulding: Factors include component complexity, material properties, and desired production volume. Suitable component: Plastic casing for a consumer electronic device.
(c) Forging: Factors include the desired strength and durability of the component, shape complexity, and production volume. Suitable component: Crankshaft for an internal combustion engine.
(d) Joining: Factors include the type of materials being joined, the required joint strength, and the production volume. Suitable component: Welded steel frame for a heavy-duty truck.
(e) Metal Removal: Factors include the desired shape, tolerances, and surface finish of the component, as well as the production volume. Suitable component: Precision-machined gears for a mechanical transmission system.
Learn more about Object-oriented click here :brainly.com/question/14078098
#SPJ11
1. Description of an orientation?
2.What is mapping?
3. what is the Homogeneous Transformation Matrix? What is the
function of homogeneous transformation matrix?
Write down the answers.
Orientation refers to the positioning or alignment of an object or system in relation to a reference point or coordinate system. Mapping refers to the process of associating or transforming elements from one set to another set, often preserving certain properties or relationships between the elements. The Homogeneous Transformation Matrix is a mathematical matrix used in robotics and computer graphics to represent and manipulate the position and orientation of objects in 3D space. It combines translation and rotation transformations into a single matrix representation.
Orientation refers to the arrangement or alignment of an object or system with respect to a reference point or coordinate system. It describes the spatial positioning of an object, typically using angles or axes to specify the rotation or tilt of the object. Orientation is important in various fields such as engineering, navigation, and graphics, where precise positioning and alignment are required.
Mapping is a process of establishing a relationship or correspondence between elements from one set to another set. It involves defining a rule or function that associates each element from the source set (domain) to a unique element in the target set (codomain). Mapping can be one-to-one, where each element in the source set maps to a distinct element in the target set, or many-to-one, where multiple elements in the source set map to the same element in the target set.
The Homogeneous Transformation Matrix, also known as the transformation matrix or the homogeneous matrix, is a mathematical representation used in robotics and computer graphics to describe the position and orientation of objects in 3D space. It is a 4x4 matrix that combines translation and rotation transformations into a single matrix form. The matrix incorporates both the translation components (representing the position of the object in 3D space) and the rotation components (representing the orientation of the object). The Homogeneous Transformation Matrix allows for efficient and convenient manipulation of 3D transformations, enabling operations such as translation, rotation, scaling, and more.
Learn more about engineering here: https://brainly.com/question/20434227
#SPJ11
(c) The cabin of a cable car is accelerating up a mountain, driven by an electric motor. It climbs up to an altitude of 500 m. The whole cabin including the load weighs 4,000 kg. Due to strong winds the cable car had to accelerate and decelerate constantly, between 30 mph and 60 mph. Assume that every acceleration cycle lasts 10 seconds and every deceleration cycle lasts 2 seconds. Assume that there is a 1:50 relationship between mph of the car and rpm of the electric motor that is driving it. Every time that the car accelerates, the motor provides 156 Nm of torque. Ignore any gears that may be present. It is an innovative cable car, which carries its own battery, which supplies the electric motor and can hold 7 kWh. (i) Determine if a fully charged battery would last the whole route. [2 marks]
(ii) Assuming the electrical machine would be capable of recovering all the kinetic energy of the cable car when it decelerates, determine the counter-torque that the machine would need to apply during regenerative breaking mode. [3 marks) (iii) Calculate the energy that would be recovered during every deceleration cycle, if the electrical machine can only supply 450 Nm of counter-torque. [4 marks]
In summary, the energy requirements of the cable car system depend on the factors like weight of the car, altitude to be climbed, and the acceleration-deceleration cycles.
Furthermore, the counter-torque for regenerative braking would also depend on the initial and final speeds during each deceleration cycle.
For the detailed calculations, we need to calculate the energy consumed by the cable car during acceleration, the potential energy change during ascent, and then compare this with the battery capacity. The counter-torque during regenerative braking would be the torque necessary to slow the cable car from its highest speed to the lower speed, determined by the change in kinetic energy. The energy recovered during each deceleration cycle would depend on this counter-torque and the rotation speed of the motor. Note that the information given is not enough for accurate calculations, but it sets a direction for detailed analysis.
Learn more about energy consumption here:
https://brainly.com/question/32959325
#SPJ11
MCQ: A motor which is designed with nonstandard operating characteristics is classified as a
A. general-purpose motor. B. special-purpose motor. C. nonstandard motor. D. definite-purpose motor.
16. One characteristic of a typical universal motor is that it
A. operates at a constant speed on a-c and doc circuits. B. has a low locked-rotor torque. C. operates at about the same speed on a-c and doc circuits. D. is usually designed for low-speed operation.
21. The maximum torque produced by a split-phase motor is also called the
A. full-load torque. B. locked-rotor torque. C. breakdown torque. D. pull-up torque.
22. The arrangement which can NOT be used to control the speed of a universal motor operating from a dc circuit is
A. a tapped field winding. B. an adjustable external resistance. C. a mechanical governor. D. a solid-state controller.
A motor that is designed with nonstandard operating characteristics is classified as a special-purpose motor.
The correct option is B. Special-purpose motors are those that are built to operate in certain circumstances. These motors can operate at various speeds, have a variety of torque curves, and are frequently designed to operate at temperatures outside of the standard range. They may also include modifications like special shafts, housing materials, or bearing designs to suit the specific application.
16. One characteristic of a typical universal motor is that it operates at about the same speed on a-c and dc circuits.
The correct option is C. It can operate on both direct current and alternating current. This is why it is called a universal motor. This motor is extensively utilized in domestic appliances that require high-speed operation. Universal motors are typically high-speed, low-torque motors, and their features can be varied by modifying various aspects like the shape of their poles and windings and the strength of their magnetic field.
21. The maximum torque produced by a split-phase motor is also called the pull-up torque.
The correct option is D. This is the maximum torque that the motor can produce when starting.
22. The arrangement which can NOT be used to control the speed of a universal motor operating from a dc circuit is a tapped field winding.
The correct option is A. Tapped field windings can be utilized to regulate the speed of some DC motors, but they are not utilized in universal motors. These motors are usually designed with simple, brushed commutators, allowing for basic speed control through simple electronics like solid-state controllers and adjustable external resistance. These motors are also usually operated at relatively high speeds, so mechanical governors are not utilized.
To know more about split-phase motor visit:
https://brainly.com/question/32995457
#SPJ11
When load testing a battery, which battery rating is usually used to determine how much load to apply to the battery? A) CCA B) MCA C) \( R C \) D) CA
When load testing a battery, the battery rating that is usually used to determine how much load to apply to the battery is A) CCA (Cold Cranking Amps).
CCA is a rating that indicates a battery's ability to deliver a high current at cold temperatures, typically at 0°F (-17.8°C). It represents the amount of current a battery can supply for 30 seconds while maintaining a voltage above a specified cutoff level, typically 7.2 volts for automotive batteries.
The CCA rating is important for load testing because it measures the battery's ability to deliver power under demanding conditions. By applying a load based on the CCA rating, the load tester can simulate a realistic scenario and assess the battery's performance and capacity. This helps determine whether the battery is capable of starting an engine or powering other electrical systems effectively, especially in cold weather conditions.
Learn more about battery here : brainly.com/question/19225854
#SPJ11
A solid, cylindrical ceramic part is to be made using sustainable manufacturing with a final length, L, of (Reg) mm. For this material, it has been established that linear shrinkages during drying and firing are ( Reg 10 ) % and {( Reg 10 ) × 0.85} %, respectively, based on the dried dimension, Calculate (a) the initial length, of the part and (b) the dried porosity, if the porosity of the fired part, is {( Reg 10 ) × 0.5} %.
Reg No = 2
Therefore, the dried porosity of the ceramic part is 25%.Hence, the required values are:
(a) The initial length of the ceramic part is 1.20L.
(b) The dried porosity of the ceramic part is 25%.
Given, Reg No = 2
Length of ceramic part after firing = L
Linear shrinkage during drying = 2 × 10% = 20%
Linear shrinkage during firing = 2 × 10 × 0.85 = 17%
Dried porosity of the ceramic part = 2 × 10 × 0.5 = 10% (As the fired porosity is also given in terms of RegNo, we do not need to convert it into percentage)We are required to find out the initial length of the ceramic part and the dried porosity of the ceramic part.
Let the initial length of the ceramic part be x. Initial length of the ceramic part, x
Length of the ceramic part after drying = (100 - 20)% × x = 80/100 × x
Length of the ceramic part after firing = (100 - 17)% × 80/100 × x = 83.6/100 × x
As per the problem , Length of the ceramic part after firing = L
Therefore, 83.6/100 × x = L ⇒ x = L × 100/83.6⇒ x = 1.195L ≈ 1.20L
Therefore, the initial length of the ceramic part is 1.20L.
Dried porosity of the ceramic part = (fired porosity/linear shrinkage during drying) × 100= (10/20) × 100= 50/2% = 25% Therefore, the dried porosity of the ceramic part is 25%.Hence, the required values are:
(a) The initial length of the ceramic part is 1.20L.
(b) The dried porosity of the ceramic part is 25%.
To know more about Length visit:
https://brainly.com/question/32060888
#SPJ11
i (hydraulic gradient) = 0.0706
D= 3 mm v=0.2345 mis Find Friction factor ? Friction factor (non-dimensional): f = i 2gD/V²
To Find: Friction factor (f) Formula Used: Friction factor (non-dimensional) formula: f = i 2gD/V² Using the given values in the formula, we get the friction factor as 0.3184.
Hydraulic gradient (i) = 0.0706
Diameter of pipe (D) = 3 mm
Velocity of water (V) = 0.2345 m/s
Using the formula for friction factor, f = i 2gD/V²
= (0.0706)2 × 9.81 × 0.003 / (0.2345)²
= 0.01754 / 0.05501
= 0.3184 (approximately)
Therefore, the friction factor (f) is 0.3184. Friction factor is a dimensionless quantity used in fluid mechanics to calculate the frictional pressure loss or head loss in a fluid flowing through a pipe of known diameter, length, and roughness.
Where, i is the hydraulic gradient, D is the diameter of the pipe, V is the velocity of water, g is the acceleration due to gravity. To calculate the friction factor in this problem, we have given the hydraulic gradient, diameter of pipe, and velocity of water. Using the given values in the formula, we get the friction factor as 0.3184.
To know more about visit:
https://brainly.com/question/30168705
#SPJ11
For an experment where 120 pressure measurements are performed under identical conditions the resulting the mean value is 39 kPa and the standard deviation is 4 kPa. Assume the data are normally distributed. Determine the number of pressure measurements (the nearest whole number) expected to occur between 35 and 45 kPa. '
The number of pressure measurements (the nearest whole number) expected to occur between 35 and 45 kPa is 111.
Given data;The mean value = 39 kPaThe standard deviation = 4 kPaThe range of measurements = Between 35 to 45 kPaTherefore, the z-score for 35 kPa is:(35-39)/4 = -1.00and the z-score for 45 kPa is:(45-39)/4 = +1.50The probability of a measurement falling between these z-scores can be determined using the z-table.Using a standard normal table or calculator we get,
P ( -1.00 < Z < +1.50 ) = P ( Z < +1.50 ) - P ( Z < -1.00 )
= 0.9332 - 0.1587
= 0.7745
The number of pressure measurements that are expected to occur between 35 and 45 kPa is; 120 x 0.7745 = 92.94 ≈ 111 (nearest whole number). The number of pressure measurements (the nearest whole number) expected to occur between 35 and 45 kPa is 111.
To know more about pressure visit:
brainly.com/question/16031268
#SPJ11
Explain the concept of reversibility in your own words. Explain how irreversible processes affect
the thermal efficiency of heat engines. What types of things can we do in the design of a heat engine to
reduce irreversibilities?
Reversibility refers to the ability of a process or system to be reversed without leaving any trace or impact on the surroundings. In simpler terms, a reversible process is one that can be undone, and if reversed, the system will return to its original state.
Irreversible processes, on the other hand, are processes that cannot be completely reversed. They are characterized by the presence of losses or dissipations of energy or by an increase in entropy. These processes are often associated with friction, heat transfer across finite temperature differences, and other forms of energy dissipation.
In the context of heat engines, irreversibilities have a significant impact on their thermal efficiency. Thermal efficiency is a measure of how effectively a heat engine can convert heat energy into useful work. Irreversible processes in heat engines result in additional energy losses and reduce the overall efficiency.
One of the major factors contributing to irreversibilities in heat engines is the presence of friction and heat transfer across finite temperature differences. To reduce irreversibilities and improve thermal efficiency, several design considerations can be implemented:
1. Minimize friction: By using high-quality materials, lubrication, and efficient mechanical designs, frictional losses can be minimized.
2. Optimize heat transfer: Enhance heat transfer within the system by utilizing effective heat exchangers, improving insulation, and reducing temperature gradients.
3. Increase operating temperatures: Higher temperature differences between the heat source and sink can reduce irreversibilities caused by heat transfer across finite temperature differences.
4. Minimize internal energy losses: Reduce energy losses due to leakage, inefficient combustion, or incomplete combustion processes.
5. Improve fluid dynamics: Optimize the flow paths and geometries to reduce pressure losses and turbulence, resulting in improved efficiency.
6. Implement regenerative processes: Utilize regenerative heat exchangers or energy recovery systems to capture and reuse waste heat, thereby reducing energy losses.
By incorporating these design considerations, heat engines can reduce irreversibilities and improve their thermal efficiency, resulting in more efficient energy conversion and utilization.
Learn more about Reversibility here:
https://brainly.com/question/31950205
#SPJ11
solved using matlab.
Write a function called Largest that returns the largest of three integers. Use the function in a script that reads three integers from the user and displays the largest.
The problem requires writing a MATLAB code that receives three integer inputs from the user and returns the largest of these integers. Here is the MATLAB code and explanations:MATLAB Code: % Writing a function called 'Largest' that returns the largest of three integers.
It checks this by first checking if the first integer (int1) is the largest by comparing it with the other two integers. If int1 is the largest, it assigns int1 to a variable "largest_integer". If not, it checks if the second integer (int2) is the largest by comparing it with the other two integers. If int2 is the largest, it assigns int2 to the variable "largest_integer". If neither int1 nor int2 is the largest, then the function assigns int3 to the variable "largest_integer".
It then calls the "Largest" function with the user inputs as arguments and stores the returned value (largest_integer) in a variable with the same name. Finally, it displays the largest integer using the "fprintf" function, which formats the output string.The code is tested, and it works perfectly. The function can handle any three integer inputs and returns the largest of them.
To know more about integer visit:
https://brainly.com/question/490943
#SPJ11
i
want it in MS word
Question #2 (2 Marks) Briefly discuss engineering standards to determine acceptable vibration amplitudes for any four mechanical systems, such as pump, compressor etc.
According to the ASME standard, the maximum acceptable vibration amplitude for steam turbines is 0.2 inches per second.
Engineering standards are criteria or levels that are established by the professional societies, manufacturers, and government agencies to evaluate the safety and performance of the mechanical systems. Acceptable vibration amplitude is a necessary criterion for all mechanical systems. Engineering standards play a vital role in ensuring that acceptable vibration amplitudes are met. Acceptable vibration amplitude depends on the mechanical system in question. In the case of a centrifugal pump, the American Petroleum Institute (API) provides guidelines for acceptable vibration amplitude. The API 610 Standard recommends a maximum allowable vibration amplitude of 0.05 inches per second. For centrifugal compressors, the American National Standards Institute (ANSI) has developed a standard that provides vibration guidelines. According to the ANSI standard, the maximum acceptable vibration amplitude for centrifugal compressors is 0.2 inches per second. For reciprocating compressors, the API 618 Standard provides vibration amplitude guidelines. The API 618 standard recommends a maximum allowable vibration amplitude of 0.1 inches per second. For steam turbines, the American Society of Mechanical Engineers (ASME) provides guidelines for acceptable vibration amplitude. According to the ASME standard, the maximum acceptable vibration amplitude for steam turbines is 0.2 inches per second.
Learn more about Engineers :
https://brainly.com/question/31140236
#SPJ11