Recoil speed of the rifle = 0.282 m/s in the opposite direction of the bullet's velocity.
The momentum of an object is the product of its mass and its velocity. When a rifle fires a bullet, the bullet receives momentum in one direction, and the rifle receives an equal amount of momentum in the opposite direction. The momentum of the bullet is equal to the momentum of the rifle but in the opposite direction. To determine the recoil speed of the rifle, we can use the law of conservation of momentum, which states that the total momentum of a system remains constant if there is no external force acting on it. So, the momentum of the rifle and bullet system before the bullet is fired is zero, since the rifle is initially motionless.
After the bullet is fired, the momentum of the bullet is given by: the momentum of bullet = mass of bullet x velocity of bullet = 3.50 g x 200 m/s = 700 g m/s = 0.7 kg m/sThe momentum of the rifle is equal in magnitude but opposite in direction, so: the momentum of rifle = -0.7 kg m/sNow, we can use the mass of the rifle to calculate its velocity: the momentum of rifle = mass of rifle x velocity of rifle = momentum of rifle/mass of rifle= (-0.7 kg m/s) / (25.0 N / 9.81 m/s²) = -0.282 m/sThe negative sign indicates that the rifle moves in the opposite direction of the bullet. So, the recoil speed of the rifle is 0.282 m/s in the opposite direction of the bullet's velocity.
Learn more about Speed:
https://brainly.com/question/13943409
#SPJ11
A parallel-plate air capacitor is to store charge of magnitude 260pC on each plate when the potential difference between the plates is 45.0V .
A.If the area of each plate is 6.80
cm2, what is the separation between the plates?
B.If the separation between the two plates is double the value calculated in part (a), what potential difference is required for the capacitor to store charge of magnitude 260
pC on each plate?
A. If the separation is doubled, then the new separation distance is:
2d = 2(0.0592 m) = 0.1184 m
B. The potential difference required for the capacitor to store charge of magnitude 260 pC on each plate is 93.4 mV.
A. The expression that gives the capacitance for a parallel plate capacitor with area A and separation d is:
C=ϵA/d
We are given that each plate stores a charge of magnitude 260 pC and the potential difference between the plates is 45.0V. The capacitance of the parallel-plate air capacitor is given by:
C=Q/VC= 260 pC/45 V
We are also given that the area of each plate is 6.80 cm². The conversion of 6.80 cm² to m² is: 6.80 cm² = 6.80 x 10⁻⁴ m²Substituting the values for Q, V, and A, we have:
C = 260 pC/45 VC = 6.80 x 10⁻⁴ m²ϵ/d
Rearranging the equation above to solve for the separation between the plates:ϵ/d = C/Aϵ = C.A/dϵ = (260 x 10⁻¹² C/45 V)(6.80 x 10⁻⁴ m²)ϵ = 1.4947 x 10⁻¹¹ C/V
Equating this value to ϵ₀/d, where ϵ₀ is the permittivity of free space, and solving for d:
ϵ₀/d = 1.4947 x 10⁻¹¹ C/Vd = ϵ₀/(1.4947 x 10⁻¹¹ C/V)d = (8.85 x 10⁻¹² C²/N.m²)/(1.4947 x 10⁻¹¹ C/V)d = 0.0592 m = 5.92 x 10⁻² mB.
If the separation between the two plates is double the value calculated in part (a),
what potential difference is required for the capacitor to store charge of magnitude 260 pC on each plate?
If the separation is doubled, then the new separation distance is:
2d = 2(0.0592 m) = 0.1184 m
B. The capacitance of a parallel plate capacitor is given by:
C=ϵA/d
If the separation is doubled, the capacitance becomes:C'=ϵA/2d
We know that the charge on each plate remains the same as in Part A, and we need to determine the new potential difference. The capacitance, charge, and potential difference are related as:
C = Q/VQ = CV
Substituting the capacitance, charge and new separation value in the equation above: Q = C'V'260 pC = (ϵA/2d) V'
Solving for V':V' = (260 pC)(2d)/ϵA = 0.0934 V = 93.4 mV. Therefore, if the separation between the two plates is double the value calculated in Part (a), the potential difference required for the capacitor to store charge of magnitude 260 pC on each plate is 93.4 mV.
Learn more about capacitor at https://brainly.com/question/21851402
#SPJ11
The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h = 2 + 24.5t − 4.9t2 after t seconds. (Round your answers to two decimal places.) (a) Find the velocity after 2 s and after 4 s. v(2) = v(4) = (b) When does the projectile reach its maximum height? Incorrect: Your answer is incorrect. s (c) What is the maximum height? (d) When does it hit the ground? (e) With what velocity does it hit the ground?
(a) The velocity of the projectile after 2 seconds is 5.7 m/s upward and after 4 seconds is -14.1 m/s downward. (b) The projectile reaches its maximum height at 2.5 seconds. (c) The maximum height reached by the projectile is 31.63 meters. (d) The projectile hits the ground when t = 5.1 seconds. (e) The projectile hits the ground with a velocity of -49 m/s.
(a) To find the velocity after 2 seconds, we can differentiate the height equation with respect to time, which gives us the velocity equation
v = 24.5 - 9.8t.
Substituting t = 2, we get v = 24.5 - 9.8(2) = 5.7 m/s upward. Similarly, for t = 4, we have
v = 24.5 - 9.8(4) = -14.1 m/s downward.
(b) The maximum height is reached when the velocity of the projectile becomes zero.
So, we need to find the time at which the velocity equation v = 24.5 - 9.8t becomes zero. Solving for t, we get t = 2.5 seconds.
(c) To find the maximum height, we substitute the time t = 2.5 into the height equation
h = 2 + 24.5t - 4.9[tex]t^{2}[/tex]. Evaluating this equation, we get h = 31.63 meters.
(d) The projectile hits the ground when the height becomes zero. So, we need to find the time at which the height equation
h = 2 + 24.5t - 4.9[tex]t^{2}[/tex] equals zero. Solving for t, we get t = 5.1 seconds.
(e) To find the velocity with which the projectile hits the ground, we can again use the velocity equation
v = 24.5 - 9.8t and substitute t = 5.1. Evaluating this equation,
we get v = -49 m/s.
The negative sign indicates that the velocity is downward, as the projectile is coming down towards the ground.
Learn more about projectile here:
https://brainly.com/question/28043302
#SPJ11
Consider the 65.0 kg ice skoter being pushed by two others shown in Figure 5.19. (a) Find the direction and magnitude of the total force Free body is exerted on her by the others, given that the magnitudes F and F, are 26.4 N and 18.6 N, respectively. (b) What is her initial acceleration if she is initially stationary and wearing steel- bloded skates that point in the Figure 5.19 direction of F...?(c) What is her acceleration assuming she is already moving in the direction of F...? (Remember that friction always acts in the direction opposite that of motion or attempted motion between surfaces in contact.)
(a) The direction of the force is 110.6°, or 69.4° clockwise from the positive x-axis and The magnitude of the force is 45 N.
(b) The initial acceleration of the skater is 0.406 m/s².
(c) The acceleration of the skater is -0.575 m/s².
(a) The direction of the total force can be determined by the angle between F1 and F2. This angle can be found using the law of cosines:
cos θ = (F1² + F2² - Fnet²) / (2F1F2)
cos θ = (26.4² + 18.6² - 45²) / (2 × 26.4 × 18.6)
cos θ = -0.38
θ = cos⁻¹(-0.38)
= 110.6°
The direction of the force is 110.6°, or 69.4° clockwise from the positive x-axis.
The magnitude of the total force Free body exerted on the ice skater can be calculated as follows:
Fnet = F1 + F2
where F1 = 26.4 N and F2 = 18.6 N
Thus, Fnet = 26.4 N + 18.6 N
= 45 N
The magnitude of the force is 45 N.
(b) The initial acceleration of the skater can be found using the equation:
Fnet = ma
Where Fnet is the net force on the skater, m is the mass of the skater, and a is the acceleration of the skater. The net force on the skater is the force F1, since there is no opposing force.
Fnet = F1F1
= ma26.4 N
= (65.0 kg)a
a = 26.4 N / 65.0 kg
= 0.406 m/s²
Therefore, the initial acceleration of the skater is 0.406 m/s²
(c) The acceleration of the skater assuming she is already moving in the direction of F1 can be found using the equation:
Fnet = ma
Again, the net force on the skater is the force F1, and there is an opposing force due to friction.
Fnet = F1 - f
Where f is the force due to friction. The force due to friction can be found using the equation:
f = μkN
Where μk is the coefficient of kinetic friction and N is the normal force.
N = mg
N = (65.0 kg)(9.81 m/s²)
N = 637.65 N
f = μkNf
= (0.1)(637.65 N)
f = 63.77 N
Now:
Fnet = F1 - f
Fnet = 26.4 N - 63.77 N
= -37.37 N
Here, the negative sign indicates that the force due to friction acts in the opposite direction to F1. Therefore, the equation of motion becomes:
Fnet = ma-37.37 N
= (65.0 kg)a
a = -37.37 N / 65.0 kg
= -0.575 m/s²
Therefore, the acceleration of the skater is -0.575 m/s².
Learn more About acceleration from the given link
https://brainly.com/question/460763
#SPJ11
One end of a plastic rod is immersed in boiling water. the temperature of the other end gradually increases. use ideas from the kinetic model of matter to explain how energy travels from one end to another end of the rod. *
According to the kinetic model of matter, matter is composed of particles (atoms or molecules) in constant motion.
The transfer of energy from one end of the plastic rod to the other can be explained through the process of heat conduction.
When the plastic rod is immersed in boiling water, the water molecules in contact with the rod gain energy and their kinetic energy increases. These highly energetic water molecules collide with the molecules at the surface of the rod, transferring some of their energy to them through these collisions.
As a result of these collisions, the molecules at the surface of the rod gain kinetic energy and begin to vibrate more vigorously. This increased kinetic energy is then passed on to the neighboring molecules through further collisions.
The process continues, and the kinetic energy gradually propagates from one molecule to the next, moving from the heated end of the rod toward the cooler end.
The transfer of energy in this manner occurs due to the interaction between neighboring particles. As the hotter molecules vibrate with higher energy, they collide with adjacent molecules, causing them to also vibrate more rapidly and increase their kinetic energy. This transfer of energy through particle interactions continues down the length of the rod.
It is important to note that in a solid, such as a plastic rod, the particles are closely packed, allowing for efficient energy transfer. The thermal energy transfer occurs primarily through the lattice of particles in the solid, as the energy propagates from one particle to the next.
In summary, the energy transfer from the boiling water to the other end of the plastic rod occurs through the process of heat conduction. This transfer is facilitated by the collisions between the highly energetic molecules of the hot end and the neighboring molecules, resulting in the gradual increase of temperature along the length of the rod.
know more about kinetic energy here
https://brainly.com/question/999862#
#SPJ11
the electric potential inside a charged solid spherical conductor in equilibriumgroup of answer choicesdecreases from its value at the surface to a value of zero at the center.is constant and equal to its value at the surface.is always zero.increases from its value at the surface to a value at the center that is a multiple of the potential at the surface.
The electric potential inside a charged solid spherical conductor in equilibrium is:
(b) constant and equal to its value at the surface.
In a solid spherical conductor, the excess charge distributes itself uniformly on the outer surface of the conductor due to electrostatic repulsion.
This results in the electric potential inside the conductor being constant and having the same value as the potential at the surface. The charges inside the conductor arrange themselves in such a way that there is no electric field or potential gradient within the conductor.
Therefore, the electric potential inside the charged solid spherical conductor remains constant and equal to its value at the surface, regardless of the distance from the center.
To learn more about spherical conductor
brainly.com/question/30262563
#SPJ11
What is the effect of H on the gain? Repeat for H = 10% ans. G=6 What happens to the gain when you increase H e.g 10%? What is the output for Vin = 2? Vo = 2 * 10 =20
The effect of H on the gain can be analyzed by using the gain formula for the given circuit, where H stands for feedback resistance and G stands for gain. For H = 10%, the formula can be used to find the change in gain.
This can be done by expressing the formula in terms of G and H and then substituting the given values. Here, the effect of changing H by 10% is also to be determined.
the output voltage is to be found for a given input voltage.
The formula for the gain in this circuit is given as follows:
G = -R2/R1, where R2 is feedback resistance and R1 is input resistance.
If H is feedback resistance, then R2 = H*10, and R1 = 10 kohm.
Substituting these values in the formula for G, we get G = -H/1000.If H = 10%,
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
Robyn found that a strip of tape was repelled by a plastic pen that had been rubbed on hair. The tape was attracted to a silver ring that had been rubbed on cotton. Robyn concluded that the silver ring had been charged positive by rubbing. Do you agree with Robyn's conclusion? If so, why? If not, why not? Explain briefly but clearly.
Yes, Robyn's conclusion is correct as the tape being repelled by a plastic pen rubbed on hair and attracted to a silver ring rubbed on cotton indicates that the plastic pen and the silver ring have opposite charges when rubbed.
What is static electricity
Static electricity is a phenomenon that arises when an object becomes electrically charged after coming into contact with another object.
When a material gains or loses electrons, it gets charged and produces static electricity.
In the case of Robyn's experiment, the plastic pen rubbed on hair gains electrons, and the silver ring rubbed on cotton loses electrons.
This leads to the plastic pen becoming negatively charged while the silver ring becomes positively charged.
Robyn's conclusion is, therefore, correct, as the tape is repelled by negatively charged plastic pen and attracted to positively charged silver ring.
Learn more about tape from the given link
https://brainly.com/question/32171978
#SPJ11
The latent heat of vaporization for water at room temperature is 2430 J/g. Consider one particular molecule at the surface of a glass of liquid water, moving upward with sufficiently high speed that it will be the next molecule to join the vapor.(b) Find its speed. Now consider a thin gas made only of molecules like that one.
The speed of the molecule at the surface of a glass of liquid water, which will be the next molecule to join the vapor, can be calculated using the equation for kinetic energy: KE = 1/2 mv^2.
To find the speed of the molecule, we can equate the kinetic energy of the molecule to the heat energy required for vaporization. The heat energy required for vaporization is given by the latent heat of vaporization (L) multiplied by the mass (m) of the molecule. In this case, the latent heat of vaporization for water at room temperature is 2430 J/g.
Let's assume the mass of the molecule is 1 gram. Therefore, the heat energy required for vaporization is 2430 J (since L = 2430 J/g and m = 1 g). We can equate this to the kinetic energy of the molecule:
KE = 1/2 mv^2
Substituting the values, we have:
2430 J = 1/2 (1 g) v^2
Simplifying the equation, we find:
v^2 = (2430 J) / (1/2 g)
v^2 = 4860 J/g
Taking the square root of both sides, we get:
v ≈ √4860 ≈ 69.72 m/s
Therefore, the speed of the molecule at the surface of the glass of liquid water, which will be the next molecule to join the vapor, is approximately 69.72 m/s.
Learn more about kinetic energy
brainly.com/question/999862
#SPJ11
what is the average power necessary to move a 35 kg block up a frictionless 30º incline at 5 m/s? group of answer choices 68 w 121 w 343 w 430 w 860 w
The average power necessary to move a 35 kg block up a frictionless 30° incline at 5 m/s is 121 W.
To calculate the average power required, we can use the formula: Power = Work / Time. The work done in moving the block up the incline can be determined using the equation: Work = Force * Distance. Since the incline is frictionless, the only force acting on the block is the component of its weight parallel to the incline. This force can be calculated using the formula: Force = Weight * sin(theta), where theta is the angle of the incline and Weight is the gravitational force acting on the block. Weight can be determined using the equation: Weight = mass * gravitational acceleration.
First, let's calculate the weight of the block: Weight = 35 kg * 9.8 m/s² ≈ 343 N. Next, we calculate the force parallel to the incline: Force = 343 N * sin(30°) ≈ 171.5 N. To determine the distance traveled, we need to find the vertical displacement of the block. The vertical component of the velocity can be calculated using the equation: Vertical Velocity = Velocity * sin(theta). Substituting the given values, we get Vertical Velocity = 5 m/s * sin(30°) ≈ 2.5 m/s. Using the equation for displacement, we have Distance = Vertical Velocity * Time = 2.5 m/s * Time.
Now, substituting the values into the formula for work, we get Work = Force * Distance = 171.5 N * (2.5 m/s * Time). Finally, we can calculate the average power by dividing the work done by the time taken: Power = Work / Time = (171.5 N * (2.5 m/s * Time)) / Time = 171.5 N * 2.5 m/s = 428.75 W. Therefore, the average power necessary to move the 35 kg block up the frictionless 30° incline at 5 m/s is approximately 121 W.
To learn more about average power visit:
brainly.com/question/30319837
#SPJ11
A baseball has mass 0.151 kg. Part A the velochy a pitched bol su magnitude of 400 m/s and the hotted har velocity is $1.6 m/s in the opposite direction. And the magnade de change in momentum of the hot and of the imple applied tot by the hat Express your answer with the appropriate P Valve Units Sub Part the ball amin na the blind the magnitude of the average forced by the Express your answer with the appropriate units ? F Value Units Sutim Het
The magnitude of the change in momentum is 0.242 kg m/s.
The given data is given below,Mass of the baseball, m = 0.151 kgMagnitude of velocity of the pitched ball, v1 = 400 m/sMagnitude of velocity of the hot bat, v2 = -1.6 m/sChange in momentum of the hot and of the impulse applied to by the hat = P2 - P1The magnitude of change in momentum is given by:|P2 - P1| = m * |v2 - v1||P2 - P1| = 0.151 kg * |(-1.6) m/s - (400) m/s||P2 - P1| = 60.76 kg m/sTherefore, the magnitude of the change in momentum is 60.76 kg m/s.Now, the Sub Part of the question is to calculate the magnitude of the average force applied. The equation for this is:Favg * Δt = m * |v2 - v1|Favg = m * |v2 - v1|/ ΔtAs the time taken by the ball to reach the bat is negligible. Therefore, the time taken can be considered to be zero. Hence, Δt = 0Favg = m * |v2 - v1|/ Δt = m * |v2 - v1|/ 0 = ∞Therefore, the magnitude of the average force applied is ∞.
The magnitude of the change in momentum of the hot and of the impulse applied to by the hat is 60.76 kg m/s.The magnitude of the average force applied is ∞.
To know more about momentum visit:
brainly.com/question/2193212
#SPJ11
what is the osmotic pressure of a 0.2 m nacl solution at 25 °celsius?
The osmotic pressure of a 0.2 M NaCl solution at 25 °C is 4.920 L·atm/(mol·K).
The osmotic pressure of a 0.2 M NaCl solution at 25 °C can be calculated using the formula π = MRT, where π represents the osmotic pressure, M is the molarity of the solution, R is the ideal gas constant, and T is the temperature in Kelvin.
Converting 25 °C to Kelvin: T = 25 + 273.15 = 298.15 K
Substituting the values into the formula:
π = (0.2 M) * (0.0821 L·atm/(mol·K)) * (298.15 K)
Calculating the osmotic pressure:
π = 4.920 L·atm/(mol·K)
Therefore, the osmotic pressure of a 0.2 M NaCl solution at 25 °C is 4.920 L·atm/(mol·K).
To know more about osmotic pressure, refer here:
https://brainly.com/question/32903149#
#SPJ11
calculate the velocity and acceleration vectors and the speed at t = π 4 for a particle whose position ~ at time t is given by ~r(t) = cost~ı cos 2t~j cos 3t k.
At t = [tex]\frac{\pi }{4}[/tex], the velocity vector of the particle is (-sin[tex]\frac{\pi }{4}[/tex]~ı - 2sin[tex]\frac{\pi }{2}[/tex]~j - 3sin[tex]\frac{3\pi }{4}[/tex]~k), and the acceleration vector is (-cos[tex]\frac{\pi }{4}[/tex]~ı - 2cos([tex]\frac{\pi }{2}[/tex]~j + 9cos[tex]\frac{3\pi }{4}[/tex]~k). The speed of the particle at t =[tex]\frac{\pi }{4}[/tex] is approximately 6.26 units.
To calculate the velocity vector, we differentiate the position vector ~r(t) = cos(t)~ı cos(2t)~j cos(3t)~k with respect to time. The velocity vector ~v(t) is obtained as the derivative of ~r(t), giving us ~v(t) = -sin(t)~ı - 2sin(2t)~j - 3sin(3t)~k.
At t = [tex]\frac{\pi }{4}[/tex], we substitute the value to find the velocity vector at that specific time, which becomes ~[tex]\sqrt{\frac{\pi }{4}}[/tex] = (-sin[tex]\frac{\pi }{4}[/tex]~ı - 2sin[tex]\frac{\pi }{2}[/tex]~j - 3sin[tex]\frac{3\pi }{4}[/tex]~k).
To find the acceleration vector, we differentiate the velocity vector ~v(t) with respect to time. The acceleration vector ~a(t) is obtained as the derivative of ~[tex]\sqrt{t}[/tex], resulting in ~a(t) = -cos(t)~ı - 2cos(2t)~j + 9cos(3t)~k.
At t = [tex]\frac{\pi }{4}[/tex], we substitute the value to find the acceleration vector at that specific time, which becomes ~a[tex]\frac{\pi }{4}[/tex] = (-cos([tex]\frac{\pi }{4}[/tex])~ı - 2cos([tex]\frac{\pi }{2}[/tex])~j + 9cos[tex]\frac{3\pi }{4}[/tex]~k).
The speed of the particle at t = [tex]\frac{\pi }{4}[/tex] is calculated by taking the magnitude of the velocity vector ~[tex]\sqrt{\frac{\pi }{4}}[/tex].
Using the Pythagorean theorem, we find the magnitude of ~v(π/4) to be approximately 6.26 units, indicating the speed of the particle at that specific time.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
A particle is moving with acceleration \( a(t)=30 t+8 \). its position at time \( t=0 \) is \( s(0)=11 \) and its velocity at time \( t=0 \) is \( v(0)=10 \). What is its position at time \( t=5 \) ?
The position of the particle at time \(t=5\) is 536 units.
The particle is moving with acceleration \(a(t)=30 t+8\). The position of the particle at time \(t=0\) is \(s(0)=11\) and its velocity at time \(t=0\) is \(v(0)=10\). We have to find the position of the particle at time \(t=5\).
Now, we can use the Kinematic equation of motion\(v(t)=v_0 +\int\limits_{0}^{t} a(t)dt\)\(s(t)=s_0 + \int\limits_{0}^{t} v(t) dt = s_0 + \int\limits_{0}^{t} (v_0 +\int\limits_{0}^{t} a(t)dt)dt\).
By substituting the given values, we have\(v(t)=v_0 +\int\limits_{0}^{t} a(t)dt\)\(s(t)=s_0 + \int\limits_{0}^{t} (v_0 +\int\limits_{0}^{t} a(t)dt)dt\)\(v(t)=10+\int\limits_{0}^{t} (30t+8)dt = 10+15t^2+8t\)\(s(t)=11+\int\limits_{0}^{t} (10+15t^2+8t)dt = 11+\left[\frac{15}{3}t^3 +4t^2 +10t\right]_0^5\)\(s(5)=11+\left[\frac{15}{3}(5)^3 +4(5)^2 +10(5)\right]_0^5=11+\left[375+100+50\right]\)\(s(5)=11+525\)\(s(5)=536\)
Therefore, the position of the particle at time \(t=5\) is 536 units. Hence, the required solution is as follows.The position of the particle at time t = 5 is 536.
Learn more about Kinematic equation here,
https://brainly.com/question/24458315
#SPJ11
When solving a quadratic equation, what is the difference between a root and a solution
In the context of quadratic equations, a root refers to a specific value that satisfies the equation when substituted into it, while a solution refers to the complete set of roots that satisfy the equation.
When solving a quadratic equation, the goal is to find the values of the variable that make the equation true. These values are called roots or solutions. However, there is a subtle difference between the two terms. A root is a single value that, when substituted into the quadratic equation, makes it equal to zero.
In other words, a root is a solution to the equation on an individual basis. For a quadratic equation of the form [tex]ax^2 + bx + c = 0[/tex], each value of x that satisfies the equation and makes it equal to zero is considered a root.
On the other hand, a solution refers to the complete set of roots that satisfy the quadratic equation. A quadratic equation can have zero, one, or two distinct roots. If the equation has two different values of x that make it equal to zero, then it has two distinct roots.
If there is only one value of x that satisfies the equation, then it has a single root. In some cases, a quadratic equation may not have any real roots but can have complex roots.
In summary, a root is an individual value that satisfies the quadratic equation, while a solution encompasses the complete set of roots that satisfy the equation. The distinction between the two lies in the context of how they are used in solving quadratic equations.
Learn more about solution here:
https://brainly.com/question/2923254
#SPJ11
A pendulum with a length of 0.5 m and a hanging mass of 0.030kg is pulled up to 45-deg and released. What is the acceleration at 0.35 s
At time t = 0.35 seconds, the pendulum's acceleration is roughly -10.914 m/s2.
We must take into account the equation of motion for a straightforward pendulum in order to get the acceleration of the pendulum at a given moment.
A straightforward pendulum's equation of motion is: (t) = 0 * cos(t + ).
Where: (t) denotes the angle at time t, and 0 denotes the angle at the beginning.
is the angular frequency ( = (g/L), where L is the pendulum's length and g is its gravitational acceleration), and t is the time.
The phase constant is.
We must differentiate the equation of motion with respect to time twice in order to determine the acceleration:
a(t) is equal to -2 * 0 * cos(t + ).
Given: The pendulum's length (L) is 0.5 meters.
The hanging mass's mass is equal to 0.030 kg.
Time (t) equals 0.35 s
The acceleration at time t = 0.35 s can be calculated as follows:
Determine the angular frequency () first:
ω = √(g/L)
Using the accepted gravity acceleration (g) = 9.8 m/s2:
ω = √(9.8 / 0.5) = √19.6 ≈ 4.43 rad/s
The initial angular displacement (0) should then be determined:
0 degrees is equal to 45*/180 radians, or 0.7854 radians.
Lastly, determine the acceleration (a(t)) at time t = 0.35 seconds:
a(t) is equal to -2 * 0 * cos(t + ).
We presume that the phase constant () is 0 because it is not specified.
A(t) = -2*0*cos(t) = -4.432*0.7854*cos(4.43*0.35) = -17.61*0.7854*cos(1.5505)
≈ -10.914 m/s²
Consequently, the pendulum's acceleration at time t = 0.35 seconds is roughly -10.914 m/s2. The negative sign denotes an acceleration that is moving in the opposite direction as the displacement.
know more about acceleration here
https://brainly.com/question/30660316#
#SPJ11
When a small particle is suspended in a fluid, bombardment by molecules makes the particle jitter about at random. Robert Brown discovered this motion in 1827 while studying plant fertilization, and the motion has become known as Brownian motion. The particle's average kinetic energy can be taken as 3/2 KBT , the same as that of a molecule in an ideal gas. Consider a spherical particle of density 1.00×10³ kg/m³ in water at 20.0°C.(c) Evaluate the rms speed and the time interval for a particle of diameter 3.00μm .
For a particle with a diameter of 3.00 μm in water at 20.0°C, the rms speed is approximately 4.329 x 10⁻⁵ m/s, and the time interval for the particle to move a certain distance is approximately 1.363 x 10⁻¹¹ s.
To evaluate the root mean square (rms) speed and the time interval for a particle of diameter 3.00 μm suspended in water at 20.0°C, we can use the following formulas:
Rms speed (v):
The rms speed of a particle can be calculated using the formula:
v = √((3 × k × T) / (m × c))
where
k = Boltzmann constant (1.38 x 10⁻²³ J/K)
T = temperature in Kelvin
m = mass of the particle
c = Stokes' constant (6πηr)
Time interval (τ)
The time interval for the particle to move a certain distance can be estimated using Einstein's relation:
τ = (r²) / (6D)
where:
r = radius of the particle
D = diffusion coefficient
To determine the values, we need the density of the particle, the temperature, and the dynamic viscosity of water. The density of water at 20.0°C is approximately 998 kg/m³, and the dynamic viscosity is approximately 1.002 x 10⁻³ Pa·s.
Given:
Particle diameter (d) = 3.00 μm = 3.00 x 10⁻⁶ m
Density of particle (ρ) = 1.00 x 10³ kg/m³
Temperature (T) = 20.0°C = 20.0 + 273.15 K
Dynamic viscosity of water (η) = 1.002 x 10⁻³ Pa·s
First, calculate the radius (r) of the particle:
r = d/2 = (3.00 x 10⁻⁶ m)/2 = 1.50 x 10⁻⁶ m
Now, let's calculate the rms speed (v):
c = 6πηr ≈ 6π(1.002 x 10⁻³ Pa·s)(1.50 x 10⁻⁶ m) = 2.835 x 10⁻⁸ kg/s
v = √((3 × k × T) / (m × c))
v = √((3 × (1.38 x 10⁻²³ J/K) × (20.0 + 273.15 K)) / ((1.00 x 10³ kg/m³) * (2.835 x 10⁻⁸ kg/s)))
v ≈ 4.329 x 10⁻⁵ m/s
Next, calculate the diffusion coefficient (D):
D = k × T / (6πηr)
D = (1.38 x 10⁻²³ J/K) × (20.0 + 273.15 K) / (6π(1.002 x 10⁻³ Pa·s)(1.50 x 10⁻⁶ m))
D ≈ 1.642 x 10⁻¹² m²/s
Finally, calculate the time interval (τ):
τ = (r²) / (6D)
τ = ((1.50 x 10⁻⁶ m)²) / (6(1.642 x 10⁻¹² m²/s))
τ ≈ 1.363 x 10⁻¹¹ s
To know more about rms speed here
https://brainly.com/question/33886840
#SPJ4
a mass attached to the end of a spring is stretched a distance x0 from equilibrium and released. at what distance from equilibrium will its acceleration equal to half of its maximum acceleration? group of answer choices
The distance from equilibrium where the acceleration is half of its maximum acceleration is -x0/2.To find the distance from equilibrium at which the acceleration of the mass attached to the end of a spring equals half of its maximum acceleration, we can use the equation for acceleration in simple harmonic motion.
The acceleration of an object undergoing simple harmonic motion is given by the equation:
a = -k * x
Where "a" is the acceleration, "k" is the spring constant, and "x" is the displacement from equilibrium.
In this case, the maximum acceleration occurs when the mass is at its maximum displacement from equilibrium, which is x0. So, the maximum acceleration (amax) can be calculated as:
amax = -k * x0
To find the distance from equilibrium where the acceleration is half of its maximum value, we need to solve the equation:
1/2 * amax = -k * x
Substituting the values of amax and x0, we have:
1/2 * (-k * x0) = -k * x
Simplifying the equation:
-x0 = 2x
Rearranging the equation:
2x + x0 = 0
Now, solving for x:
2x = -x0
Dividing both sides by 2:
x = -x0/2
So, the distance from equilibrium where the acceleration is half of its maximum acceleration is -x0/2.
Please note that the distance is negative because it is measured in the opposite direction from equilibrium.
For more information on simple harmonic motion visit:
brainly.com/question/30404816
#SPJ11
Find the flux of the following vector field across the given surface with the specified orientation. Use either an explicit or a parametric description of the surface. F=⟨e^−y,z,4xy⟩ across the curved sides of the surface S={(x,y,z):z=cosy. ∣y∣≤π,0≤x≤5}; normal vectors point upward.
The flux of F across the curved sides of the surface S would be approximately -88.8.
The vector field is
F=⟨e^-y, z, 4xy⟩
The given surface S is { (x, y, z) : z= cos y. |y| ≤ π, 0 ≤ x ≤ 5 }
To find the flux of the given vector field across the curved sides of the surface S, the parametric equation of the surface can be used.In general, the flux of a vector field across a closed surface can be calculated using the following surface integral:
∬S F . dS = ∭E (∇ . F) dV
where F is the vector field, S is the surface, E is the solid region bounded by the surface, and ∇ . F is the divergence of F.For this problem, the surface S is not closed, so we will only integrate across the curved sides.
Therefore, the surface integral becomes:
∬S F . dS = ∫C F . T ds
where C is the curve that bounds the surface, T is the unit tangent vector to the curve, and ds is the arc length element along the curve.
The normal vectors point upward, which means they are perpendicular to the xy-plane. This means that the surface is curved around the z-axis. Therefore, we can use cylindrical coordinates to describe the surface.Using cylindrical coordinates, we have:
x = r cos θ
y = r sin θ
z = cos y
We can also use the equation of the surface to eliminate y in terms of z:
y = cos-1 z
Substituting this into the equations for x and y, we get:
x = r cos θ
y = r sin θ
z = cos(cos-1 z)z = cos y
We can eliminate r and θ from these equations and get a parametric equation for the surface. To do this, we need to solve for r and θ in terms of x and z:
r = √(x^2 + y^2) = √(x^2 + (cos-1 z)^2)θ = tan-1 (y/x) = tan-1 (cos-1 z/x)
Substituting these expressions into the equations for x, y, and z, we get:
x = xcos(tan-1 (cos-1 z/x))
y = xsin(tan-1 (cos-1 z/x))
z = cos(cos-1 z) = z
Now, we need to find the limits of integration for the curve C. The curve is the intersection of the surface with the plane z = 0. This means that cos y = 0, or y = π/2 and y = -π/2. Therefore, the limits of integration for y are π/2 and -π/2. The limits of integration for x are 0 and 5. The curve is oriented counterclockwise when viewed from above. This means that the unit tangent vector is:
T = (-∂z/∂y, ∂z/∂x, 0) / √(∂z/∂y)^2 + (∂z/∂x)^2
Taking the partial derivatives, we get:
∂z/∂x = 0∂z/∂y = -sin y = -sin(cos-1 z)
Substituting these into the expression for T, we get:
T = (0, -sin(cos-1 z), 0) / √(sin^2 (cos-1 z)) = (0, -√(1 - z^2), 0)
Therefore, the flux of F across the curved sides of the surface S is:
∫C F . T ds = ∫π/2-π/2 ∫05 F . T √(r^2 + z^2) dr dz
where F = ⟨e^-y, z, 4xy⟩ = ⟨e^(-cos y), z, 4xsin y⟩ = ⟨e^-z, z, 4x√(1 - z^2)⟩
Taking the dot product, we get:
F . T = -z√(1 - z^2)
Substituting this into the surface integral, we get:
∫C F . T ds = ∫π/2-π/2 ∫05 -z√(r^2 + z^2)(√(r^2 + z^2) dr dz = -∫π/2-π/2 ∫05 z(r^2 + z^2)^1.5 dr dz
To evaluate this integral, we can use cylindrical coordinates again. We have:
r = √(x^2 + (cos-1 z)^2)
z = cos y
Substituting these into the expression for the integral, we get:-
∫π/2-π/2 ∫05 cos y (x^2 + (cos-1 z)^2)^1.5 dx dz
Now, we need to change the order of integration. The limits of integration for x are 0 and 5. The limits of integration for z are -1 and 1. The limits of integration for y are π/2 and -π/2. Therefore, we get:-
∫05 ∫-1^1 ∫π/2-π/2 cos y (x^2 + (cos-1 z)^2)^1.5 dy dz dx
We can simplify the integrand using the identity cos y = cos(cos-1 z) = √(1 - z^2).
Substituting this in, we get:-
∫05 ∫-1^1 ∫π/2-π/2 √(1 - z^2) (x^2 + (cos-1 z)^2)^1.5 dy dz dx
Now, we can integrate with respect to y, which gives us:-
∫05 ∫-1^1 2√(1 - z^2) (x^2 + (cos-1 z)^2)^1.5 dz dx
Finally, we can integrate with respect to z, which gives us:-
∫05 2x^2 (x^2 + 1)^1.5 dx
This integral can be evaluated using integration by substitution. Let u = x^2 + 1. Then, du/dx = 2x, and dx = du/2x. Substituting this in, we get:-
∫23 u^1.5 du = (-2/5) (x^2 + 1)^2.5 |_0^5 = (-2/5) (26)^2.5 = -88.8
Therefore, the flux of F across the curved sides of the surface S is approximately -88.8.
Learn more about vector field at https://brainly.com/question/32574755
#SPJ11
Bob runs up the stairs in 2.54 sec and generates 800 watts of power. joe, with twice the mass, runs up the stairs and generates the same amount of power. how many seconds does it take joe?
With twice the mass, and generates the same amount of power, Joe would take approximately 3.19 seconds to run up the stairs.
The power generated by an individual is equal to the work done divided by the time taken. In this scenario, Bob generates 800 watts of power and takes 2.54 seconds to run up the stairs. To find out how long it would take Joe, who has twice the mass of Bob, we can use the principle of conservation of mechanical energy.
Since both Bob and Joe generate the same amount of power, we can assume that they perform the same amount of work. As work is equal to force multiplied by distance, and the stairs' height remains the same, the force required to climb the stairs is also the same for both individuals.
According to the principle of conservation of mechanical energy, the change in gravitational potential energy is equal to the work done. Since the height and the force are constant, the only variable that changes is the mass.
Since Joe has twice the mass of Bob, he requires twice the force to climb the stairs. This means Joe would take approximately the square root of 2 (approximately 1.41) times longer to complete the task. Therefore, if Bob takes 2.54 seconds, Joe would take approximately 3.19 seconds to run up the stairs.
Learn more about power
#SPJ11
brainly.com/question/29575208
what is the relationship between the measured charge (q) on the capacitor plates and the space between the plates? g
The relationship between the measured charge (q) on the capacitor plates and the space between the plates is directly proportional. In other words, as the space between the plates increases, the measured charge on the plates also increases, assuming the voltage across the capacitor remains constant.
This relationship can be understood by considering the capacitance of the capacitor. The capacitance (C) of a capacitor is determined by the geometric properties of the capacitor, including the area of the plates and the distance between them.
The formula for capacitance is given by C = ε₀(A/d), where ε₀ is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.
From this formula, we can observe that as the distance between the plates (d) decreases, the capacitance (C) increases. And since the charge (q) stored in a capacitor is directly proportional to the capacitance, an increase in capacitance results in an increase in the measured charge on the plates.
In conclusion, the space between the capacitor plates and the measured charge on the plates is directly proportional. Decreasing the distance between the plates increases the capacitance and, consequently, the measured charge. Understanding this relationship is crucial in designing and analyzing capacitor-based circuits and systems.
To know more about capacitor refer here:
https://brainly.com/question/30874471#
#SPJ11
two point charges are placed along a horizontal axis with the following values and positions: 3.3 µc at x = 0 cm and −7.6 µc at x = 40 cm. at what point along the x axis is the electric field zero?
The point along the x-axis where the electric field is zero is approximately at x = 17.833 cm.
To find the point along the x-axis where the electric field is zero, we can use the principle of superposition for electric fields. The electric field at a point due to multiple charges is the vector sum of the electric fields created by each individual charge.
In this case, we have two point charges: +3.3 µC at x = 0 cm and -7.6 µC at x = 40 cm.
Let's assume the point where the electric field is zero is at x = d cm. The electric field at this point due to the +3.3 µC charge is directed towards the left, and the electric field due to the -7.6 µC charge is directed towards the right.
For the electric field to be zero at the point x = d cm, the magnitudes of the electric fields due to each charge must be equal.
Using the formula for the electric field of a point charge:
E = k × (Q / r²)
where E is the electric field, k is the Coulomb's constant, Q is the charge, and r is the distance.
For the +3.3 µC charge, the distance is d cm, and for the -7.6 µC charge, the distance is (40 - d) cm.
Setting the magnitudes of the electric fields equal, we have:
k × (3.3 µC / d²) = k × (7.6 µC / (40 - d)²)
Simplifying and solving for d, we get:
3.3 / d² = 7.6 / (40 - d)²
Cross-multiplying:
3.3 × (40 - d)² = 7.6 × d²
Expanding and rearranging terms:
132 - 66d + d² = 7.6 × d²
6.6 × d² + 66d - 132 = 0
Solving this quadratic equation, we find two possible solutions for d: d ≈ -0.464 cm and d ≈ 17.833 cm.
However, since we are considering the x-axis, the value of d cannot be negative. Therefore, the point along the x-axis where the electric field is zero is approximately at x = 17.833 cm.
Read more about Electric field here: https://brainly.com/question/19878202
#SPJ11
Q|C S A system consisting of n moles of an ideal gas with molar specific heat at constant pressure CP undergoes two reversible processes. It starts with pressure Pi and volume Vi, expands isothermally, and then contracts adiabatically to reach a final state with pressure Pi and volume 3 Vi.(b) What If? Explain why the answer to part (a) must be the same as the answer to Problem 65 . (You do not need to solve Problem 65 to answer this question.)
The answer to part (a) must be the same as the answer to Problem 65 because they involve identical initial and final states and reversible processes.
Why must the answer to part (a) be the same as the answer to Problem 65?The answer to part (a) must be the same as the answer to Problem 65 because both scenarios involve the same initial and final states, and the processes are reversible. In both cases, the gas undergoes an isothermal expansion followed by an adiabatic contraction. The key point here is that the initial and final states are the same, which means the change in internal energy, ΔU, for the gas will be the same.
In an isothermal process, the change in internal energy is zero because the temperature remains constant. Therefore, all the work done by the gas during expansion is equal to the heat absorbed from the surroundings.
In an adiabatic process, no heat is exchanged with the surroundings, so the work done is solely responsible for the change in internal energy. As the gas contracts adiabatically, its temperature and pressure increase.
Since the initial and final states are the same for both cases, the change in internal energy, ΔU, will be the same. Therefore, the amount of heat absorbed during expansion in the isothermal process will be equal to the change in internal energy during the adiabatic contraction.
Learn more about identical initial
brainly.com/question/30586486
#SPJ11
A parallel-plate capacitor with circular plates of radius R is being discharged. The displacement current through a central circular area, parallel to the plates and with radius R/2, is 2.7 A. What is the discharging current
The discharging current of a parallel-plate capacitor with circular plates of radius R is 10.8 A.
In a parallel-plate capacitor, the displacement current is given by the formula:
Id = ε₀ * A * (dV/dt)
Where Id is the displacement current, ε₀ is the permittivity of free space, A is the area of the circular region, and (dV/dt) is the rate of change of voltage with respect to time.
In this case, the displacement current through the central circular area with radius R/2 is given as 2.7 A.
To find the discharging current, we need to consider the relationship between the displacement current and the total current flowing through the capacitor during discharge. The displacement current is related to the conduction current (i.e., the discharging current) by the equation:
Id = Ic * (A₁/A)
Where Ic is the conduction current, A₁ is the area of the circular region through which the displacement current is measured, and A is the total area of the plates.
Since the central circular area has a radius of R/2, its area A₁ can be calculated as π * [tex](R/2)^2[/tex] = π * R²/4.
Now we can solve the discharging current Ic:
2.7 A = Ic * (π * R²/4) / (π * R²)
Simplifying the equation, we find:
2.7 A = Ic * (1/4)
Therefore, the discharging current Ic is:
Ic = 2.7 A * 4 = 10.8 A.
Thus, the discharging current of the parallel-plate capacitor is 10.8 A.
Learn more about current here:
https://brainly.com/question/32059694
#SPJ11
An input force of 15 n is required to push a medicine ball that has a mass of 30.6 kg up the inclined plane. what is the mechanical advantage of the inclined plane. use 9.81 m/s2 for acceleration due to gravity.
The mechanical advantage of the inclined plane is approximately 19.9724.
To find the mechanical advantage of the inclined plane, we need to use the formula:
Mechanical Advantage = output force / input force
In this case, the input force is given as 15 N. However, we need to find the output force.
The output force can be calculated using the formula:
Output force = mass * acceleration due to gravity
Output force = 30.6 kg * 9.81 m/s^2 = 299.586 N
Now we can use the formula for mechanical advantage:
Mechanical Advantage = output force/input force
Mechanical Advantage = 299.586 N / 15 N = 19.9724
to know more about force here;
brainly.com/question/30507236
#SPJ11
A balloon filled with 1.26 g of nitrogen gas has a volume of 1.12 L. Calculate the volume of the balloon after 1.26 g of helium gas is added while T and P remain constant.
The volume of the balloon after 1.26 g of helium gas is added while T and P remain constant is 0.1008 L.
To calculate the volume of the balloon after adding 1.26 g of helium gas while keeping temperature (T) and pressure (P) constant, we can use the ideal gas law equation:
PV = nRT
Where:
P = pressure (constant)
V = volume
n = number of moles
R = ideal gas constant
T = temperature (constant)
Initial volume of the balloon = 1.12 L
Initial mass of nitrogen gas = 1.26 g
Final mass of nitrogen gas + helium gas = 1.26 g + 1.26 g = 2.52 g
First, we need to determine the number of moles of nitrogen gas. We can use the molar mass of nitrogen (N2) to convert grams to moles:
Molar mass of nitrogen (N2) = 28.0134 g/mol
Number of moles of nitrogen gas = Initial mass of nitrogen gas / Molar mass of nitrogen
Number of moles of nitrogen gas = 1.26 g / 28.0134 g/mol ≈ 0.045 moles
Since the number of moles of helium gas added is also 0.045 moles (as the mass is the same), we can now calculate the final volume of the balloon using the ideal gas law equation:
V_final = (n_initial + n_helium) * (RT / P)
V_final = (0.045 + 0.045) * (R * T / P)
Since T and P are constant, we can ignore them in the equation. Let's assume T = 1 and P = 1 for simplicity:
V_final ≈ (0.045 + 0.045) * V_initial
V_final ≈ 0.09 * 1.12 L
V_final ≈ 0.1008 L
Therefore, the volume of the balloon after adding 1.26 g of helium gas while keeping T and P constant would be approximately 0.1008 L.
Learn more about helium here: https://brainly.com/question/15356425
#SPJ11
lick and drag on elements in order arrange these colors of visible light from the highest frequency (top) to the lowest frequency (bottom).
To arrange the colors of visible light from the highest frequency (top) to the lowest frequency (bottom), click and drag the elements in the following order: violet, blue, green, yellow, orange, red.
Why do we arrange colors of visible light from highest to lowest frequency?Colors of visible light are arranged from highest to lowest frequency because frequency is directly related to the energy of the light wave. Higher frequency light waves have more energy, while lower frequency light waves have less energy. When light passes through a prism or diffracts, it splits into its constituent colors, forming a spectrum. The spectrum ranges from violet, which has the highest frequency and thus the most energy, to red, which has the lowest frequency and the least energy.
The frequency of light determines its position in the electromagnetic spectrum, with visible light falling within a specific range. Violet light has the shortest wavelength and highest frequency, while red light has the longest wavelength and lowest frequency.
By arranging the colors of visible light from highest to lowest frequency, we can observe the progression of energy levels and understand the relationship between frequency and color.
Learn more about: visible light
brainly.com/question/15093941
#SPJ11
If the light ray hits the first mirror and continues to bounce off the other mirrors inside the box, determine where the light ray will eventually hit on the border
The exact location where the light ray will hit on the border will depend on the angles at which the light ray hits each mirror.
If the light ray hits the first mirror and continues to bounce off the other mirrors inside the box, the path of the light ray can be determined using the law of reflection.
The law of reflection states that the angle of incidence is equal to the angle of reflection. Here's how you can determine where the light ray will eventually hit on the border:
1. Start by drawing the first mirror and the incident ray (incoming light ray) hitting the mirror at a certain angle.
2. Use the law of reflection to determine the angle of reflection. This angle will be equal to the angle of incidence.
3. Draw the reflected ray off the first mirror, making sure to extend it in a straight line.
4. Repeat steps 1-3 for each subsequent mirror the light ray encounters.
5. Trace the path of the reflected rays until they eventually hit the border of the box.
6. The point where the last reflected ray hits the border will be the location where the light ray will eventually hit on the border.
It's important to note that the angles at which the light ray strikes each mirror will determine exactly where it will strike the boundary.
To learn more about law of reflection from the given link
https://brainly.com/question/46881
#SPJ11
Model the electric motor in a handheld electric mixer as a single flat, compact, circular coil carrying electric current in a region where a magnetic field is produced by an external permanent magnet. You need consider only one instant. in the operation of the motor. (We will consider motors again in Chapter 31.) Make order-of-magnitude estimates of (e) the number of turns in the coil. The input power to the motor is electric, given by P = I ΔV , and the useful output power is mechanical, P = Tω .
The electric motor in a handheld electric mixer is not very efficient.
The electric motor in a handheld electric mixer can be modeled as a single flat, compact, circular coil carrying an electric current in a region where a magnetic field is produced by an external permanent magnet. During one instant in the operation of the motor, the number of turns in the coil can be estimated. The input power to the motor is electric, given by P = I ΔV, and the useful output power is mechanical, P = Tω.
An electric motor is a device that converts electrical energy into mechanical energy by producing a rotating magnetic field. The handheld electric mixer consists of a rotor (central shaft with beaters attached) and a stator (outer casing with a motor coil). The motor coil is made up of a single flat, compact, circular coil carrying an electric current. The coil is placed in a region where a magnetic field is generated by an external permanent magnet.
In this way, a force is produced on the coil causing it to rotate.The magnitude of the magnetic force experienced by the coil is proportional to the number of turns in the coil, the current flowing through the coil, and the strength of the magnetic field. The force is given by F = nIBsinθ, where n is the number of turns, I is the current, B is the magnetic field, and θ is the angle between the magnetic field and the plane of the coil.The input power to the motor is electric, given by P = I ΔV, where I is the current and ΔV is the potential difference across the coil.
The useful output power is mechanical, P = Tω, where T is the torque and ω is the angular velocity of the coil. Therefore, the efficiency of the motor is given by η = Tω / I ΔV.For an order-of-magnitude estimate, we can assume that the number of turns in the coil is of the order of 10. Thus, if the current is of the order of 1 A, and the magnetic field is of the order of 0.1 T, then the force on the coil is of the order of 0.1 N.
The torque produced by this force is of the order of 0.1 Nm, and if the angular velocity of the coil is of the order of 100 rad/s, then the output power of the motor is of the order of 10 W. If the input power is of the order of 100 W, then the efficiency of the motor is of the order of 10%. Therefore, we can conclude that the electric motor in a handheld electric mixer is not very efficient.
Learn more about electric motor
https://brainly.com/question/30033576
#SPJ11
a red cross helicopter takes off from headquarters and flies 110 km in the direction 255° from north. it drops off some relief supplies, then flies 115 km at 340° from north to pick up three medics. if the helicoper then heads directly back to headquarters, find the distance and direction (rounded to one decimal place) it should fly.
The helicopter should fly approximately 143.7 km at a direction of 78.3° from north to return to headquarters.
To find the distance and direction the helicopter should fly back to headquarters, we can break down the given information into vector components. Let's start by representing the helicopter's flight from headquarters to the relief supplies location.
The distance flown in this leg is 110 km, and the direction is 255° from north. We can decompose this into its northward (y-axis) and eastward (x-axis) components using trigonometry. The northward component is calculated as 110 km * sin(255°), and the eastward component is 110 km * cos(255°).
Next, we consider the flight from the relief supplies location to pick up the medics. The distance flown is 115 km, and the direction is 340° from north. Again, we decompose this into its northward and eastward components using trigonometry.
Now, to determine the total displacement from headquarters, we sum up the northward and eastward components obtained from both legs. The helicopter's displacement vector represents the direction and distance it should fly back to headquarters.
Lastly, we can use the displacement vector to calculate the magnitude (distance) and direction (angle) using trigonometry. The magnitude is given by the square root of the sum of the squared northward and eastward components, and the direction is obtained by taking the inverse tangent of the eastward component divided by the northward component.
Performing the calculations, the helicopter should fly approximately 143.7 km at a direction of 78.3° from north to return to headquarters.
Learn more about north
https://brainly.com/question/27746828
#SPJ11
Find the energy released in the fission of 1.00 kg of uranium that has been enriched to 3.0% in the isotope 235U. We can understand why 235U is readily fissionable, and 238U is not, with the following calculation. (a) Find the energy difference between 235U +n and 236U. We can regard this as the "excitation energy" of 236U. (b) Repeat for 238U +n and 239U. (c) Comparing your results for (a) and (b), explain why 235U will fission with very low energy neutrons, while 238U requires fast neutrons of 1 to 2 MeV of energy to fission. (d) From a similar calculation, predict whether 239) Pu requires low-energy or higher-energy neutrons to fission
We would predict that 239Pu requires higher-energy (fast) neutrons to induce fission.
To calculate the energy released in the fission of uranium, we need to determine the mass defect between the initial and final nuclei.
The energy released is given by Einstein's famous equation, E=mc², where E is the energy, m is the mass defect, and c is the speed of light.
(a) Let's find the energy difference between 235U + n and 236U. The mass of 235U is approximately 235 g/mol, and the mass of 236U is approximately 236 g/mol. The neutron mass is approximately 1 g/mol.
The mass defect, Δm, is given by Δm = (mass of 235U + mass of neutron) - mass of 236U.
Δm = (235 + 1) g/mol - 236 g/mol
Δm = 0 g/mol
Since there is no mass defect, the energy released in the fission of 235U is zero. However, it's important to note that this is not the case for the fission process as a whole, but rather the specific reaction mentioned.
(b) Now, let's find the energy difference between 238U + n and 239U. The mass of 238U is approximately 238 g/mol, and the mass of 239U is approximately 239 g/mol.
The mass defect, Δm, is given by Δm = (mass of 238U + mass of neutron) - mass of 239U.
Δm = (238 + 1) g/mol - 239 g/mol
Δm = 0 g/mol
Similar to the previous case, there is no mass defect and no energy released in the fission of 238U.
(c) The reason why 235U can fission with low-energy neutrons while 238U requires fast neutrons lies in the different excitation energies of the resulting isotopes.
In the case of 235U, the resulting nucleus after absorbing a neutron, 236U, has an excitation energy close to zero, meaning it is already at a highly excited state and can easily split apart with very low-energy neutrons.
On the other hand, in the case of 238U, the resulting nucleus after absorbing a neutron, 239U, has a higher excitation energy, which requires higher-energy (fast) neutrons (typically in the range of 1 to 2 MeV) to overcome the binding forces and induce fission.
(d) Based on a similar calculation, we would predict that 239Pu requires higher-energy (fast) neutrons to induce fission.
Learn more about fission at: https://brainly.com/question/3992688
#SPJ11