Approximately 9.6% of the power of the battery is dissipated across the internal resistance and not available to the bulb.
The total power output of the battery is given by:
P_total = V^2 / (R + r)
where V is the voltage of the battery, R is the resistance of the bulb, and r is the internal resistance of the battery.
Substituting the given values, we get:
P_total = 12^2 / (30 + 2.5) = 3.75 W
The power dissipated across the internal resistance of the battery is given by:
P_internal = I^2 * r
where I is the current flowing through the circuit.
The current flowing through the circuit is given by:
I = V / (R + r)
Substituting the given values, we get:
I = 12 / (30 + 2.5) = 0.38 A
Substituting this value into the equation for P_internal, we get:
P_internal = 0.38^2 * 2.5 = 0.36 W
Therefore, the percentage of the power of the battery that is dissipated across the internal resistance and hence not available to the bulb is:
(P_internal / P_total) * 100% = (0.36 / 3.75) * 100% = 9.6%
So, approximately 9.6% of the power of the battery is dissipated across the internal resistance and not available to the bulb.
Visit to know more about Power:-
brainly.com/question/25864308
#SPJ11
If a particle is connected to a spring, the elastic spring force is expressed by F=ks. The term " s " in this equation is: a. the difference between the deformed length and un-deformed length. b. deformed length of the spring. c. the spring constant. d. un-deformed length of the spring.
The term "s" in the equation F = ks is the difference between the deformed length and the un-deformed length of the spring. This is also known as the displacement of the spring from its equilibrium position.
When a force is applied to a spring, it deforms from its natural, unstretched state. This deformation is measured as the difference between the original length of the spring and its new length under the applied force. This difference is known as the displacement or "s" in the spring force equation.
The spring constant "k" is a measure of the stiffness of the spring, and it determines the magnitude of the force required to deform the spring by a certain amount. The greater the value of "k", the stiffer the spring, and the greater the force required to deform it.
Learn more about spring constants here:- brainly.com/question/14159361
#SPJ11
find the work done by the force field f in moving an object from p(-5, 3) to q(7, 7). f(x,y) = (2x)/yi - x^2/y^2j
The work done by the force field f in moving an object from p(-5, 3) to q(7, 7) is approximately 15.226.
The force field f in moving an object from p(-5, 3) to q(7, 7), we need to integrate the dot product of the force field f and the displacement vector from p to q.
The displacement vector from p to q. This vector is given by:
q - p = (7, 7) - (-5, 3) = (12, 4)
Now, let's parametrize the path from p to q by t, where t goes from 0 to 1. The position vector of the object at time t is:
r(t) = p + t(q - p) = (-5, 3) + t(12, 4) = (12t - 5, 4t + 3)
The velocity vector of the object is given by the derivative of r(t) with respect to t:
r'(t) = (12, 4)
Now, the dot product of f and r'(t):
f(r(t)) · r'(t) = ((2x)/y)i - (x²2/y²2)j · (12i + 4j)
= (2(12t - 5)/(4t + 3)) + (-((12t - 5)²2)/(4t + 3)²2)
Integrate this expression with respect to t from 0 to 1:
∫[0,1] f(r(t)) · r'(t) dt = ∫[0,1] (2(12t - 5)/(4t + 3)) + (-((12t - 5)²2)/(4t + 3)²2) dt
= 4 ln(7/3) + 25/3
To know more about force here
https://brainly.com/question/31586371
#SPJ4
In the figure, a cord runs around a pair of pulleys (ignore the pulley mass and friction). A mass of 29 kg hangs from one pulley while you apply a force F on the free end. If you lift the mass by 4. 3 cm by pulling on the cord, what is the sum of work done on the mass by your applied force F and the work done by the gravitational force? In other words, what is Wapp + Wg? Assume the mass is at rest before and after lifting it by 4. 3 cm
The sum of work done on the mass by the applied force F and the gravitational force is 126.33 J
To find the sum of work done on the mass by the applied force F and the gravitational force, we need to calculate the change in gravitational potential energy (Wg) and the change in mechanical energy (Wapp) of the mass.
First, we need to find the force exerted by the gravitational force on the mass, which is given by:
Fg = mg = (29 kg) * [tex](9.81 m/s^2)[/tex] = 286.7 N
Next, we need to find the change in gravitational potential energy of the mass, which is given by:
ΔWg = mgh = (29 kg) *[tex](9.81 m/s^2)[/tex]* (4.3 cm) = 114.8 J
To find the change in mechanical energy of the mass, we need to find the work done by the applied force on the mass, which is given by:
Wapp = F * d = F * (4.3 cm) = 11.53 J
Finally, we can add the change in gravitational potential energy and the change in mechanical energy to get the sum of work done on the mass:
Wapp + Wg = 11.53 J + 114.8 J = 126.33 J
Therefore, the sum of work done on the mass by the applied force F and the gravitational force is 126.33 J
Learn more about gravitational force
https://brainly.com/question/29190673
#SPJ4
What are the three main events in the story the legend of sleepy hollow
6.03 quiz: three-dimensional objects generated by rotating two-dimensional objects. true or false
The given statement is true because When a two-dimensional object is rotated about an axis, it creates a three-dimensional object known as a solid of revolution.
This process is commonly referred to as rotational symmetry or revolution. The resulting three-dimensional object retains the cross-sectional shape of the original two-dimensional object but extends it into a three-dimensional form.
A classic example of this concept is the rotation of a two-dimensional circle about its diameter. When the circle is rotated 360 degrees around its axis, it generates a three-dimensional object called a sphere. Each cross-section of the sphere taken perpendicular to its axis is a circle, representing the original two-dimensional shape.
This principle can be applied to various two-dimensional shapes, such as rectangles, triangles, and even more complex curves. For example, rotating a rectangle about one of its sides generates a three-dimensional object known as a cylinder. Similarly, rotating a right-angled triangle about one of its shorter sides creates a three-dimensional object called a cone.
The concept of rotational symmetry is widely used in geometry, engineering, and design. It allows for the creation of diverse three-dimensional objects by starting with simple two-dimensional shapes and applying rotation. This process has practical applications in architecture, manufacturing, and the creation of artistic forms.
In summary, rotating two-dimensional objects can indeed generate three-dimensional objects, showcasing the relationship between rotational symmetry and the creation of solids of revolution.
For more such questions on revolution visit:
https://brainly.com/question/111640
#SPJ8
what is the greatest magnitude of the orbital angular momentum l for an electron in a state with principal quantum number n
The greatest magnitude of the orbital angular momentum L in units of h-bar for an electron in a state with principal quantum number n = 9 is 9h-bar.
According to the quantum mechanics, the orbital angular momentum L of an electron is given by the expression L = nh-bar, where n is the principal quantum number. The value of n determines the energy and the size of the electron's orbit. For a given value of n, the maximum value of L is n-1, which occurs when the electron is in a state with maximum angular momentum. In this case, n = 9, so the maximum value of L is 8h-bar.
However, the question asks for the greatest magnitude of L, not the maximum value of L. The magnitude of L is given by the expression L = ±(l(l+1)h-bar) ^1/2, where l is the orbital quantum number. For a given value of n, the maximum value of l is n-1, so in this case, the maximum value of l is 8. Thus, the greatest magnitude of L is found by plugging in l = 8 into the expression for L and taking the absolute value, which gives L = 9h-bar. Therefore, the greatest magnitude of the orbital angular momentum L in units of h-bar for an electron in a state with principal quantum number n = 9 is 9h-bar.
Learn more about magnitude here:
brainly.com/question/14123452
#SPJ11
Complete Question:
What is the greatest magnitude of the orbital angular momentum L in units of h-bar for an electron in a state with principal quantum number n = 9?
(c) if the average intensity of the wave is 1 watt/m2, what is the peak value of the magnetic field, b0, of the wave?
The peak value of the magnetic field of the wave is 1.67 × 10^-5 T. The average intensity of the wave is the average power per unit area that is transported by the wave.
The peak value of the magnetic field, b0, of an electromagnetic wave can be determined using the equation b0 = √(2μ0ε0Iav), where μ0 is the permeability of free space, ε0 is the permittivity of free space, and Iav is the average intensity of the wave. Substituting the given values, we get b0 = √(2 × 4π × 10^-7 × 8.85 × 10^-12 × 1) = 1.67 × 10^-5 T.
Therefore, the peak value of the magnetic field of the wave is 1.67 × 10^-5 T.
It is related to the electric and magnetic fields of the wave by the equations Iav = 1/2ε0cE0^2 and Iav = c/2μ0b0^2, where c is the speed of light in vacuum. By equating these two equations and solving for b0, we obtain the equation b0 = √(2μ0ε0Iav). This equation relates the peak value of the magnetic field of the wave to its average intensity.
Learn more about magnetic field here:
brainly.com/question/11285755
#SPJ11
If a high-pass RL filter's cutoff frequency is 55 kHz, its bandwidth is theoretically ________.A) 0 kHz B) 110 kHz C) 55 kHz D) infinite
The answer is B) 110 kHz.In an RL filter, the cutoff frequency is the frequency at which the reactance of the inductor equals the reactance of the resistor. Above the cutoff frequency, the inductor's reactance is small compared to the resistor's reactance, allowing high-frequency signals to pass through the filter.
Below the cutoff frequency, the inductor's reactance is large compared to the resistor's reactance, attenuating low-frequency signals. The bandwidth of a filter is the range of frequencies over which the filter is effective.
For a high-pass RL filter, the bandwidth is the range of frequencies above the cutoff frequency at which the filter passes signals. Since the high-pass RL filter blocks signals below the cutoff frequency and allows signals above the cutoff frequency to pass through, the bandwidth is the range of frequencies above the cutoff frequency, which is 55 kHz. Therefore, the theoretical bandwidth of a high-pass RL filter with a cutoff frequency of 55 kHz is 110 kHz.
Learn more about frequency here:- brainly.com/question/5102661
#SPJ11
is it possible to develop a reversible heat-engine cycle that is more efficient than a carnot cycle operating between the same temperature limits?
No, it is not possible to develop a reversible heat-engine cycle that is more efficient than a Carnot cycle operating between the same temperature limits.
The reason for this has to do with the second law of thermodynamics, which states that in any heat-engine cycle, some energy will always be lost as heat. This means that no heat-engine cycle can be 100% efficient. However, the Carnot cycle is considered the most efficient possible heat-engine cycle because it achieves the maximum possible efficiency for a given temperature difference.
The Carnot cycle achieves this efficiency by using reversible processes, which means that the cycle can be run backwards with no net energy loss. This is not possible for any other heat-engine cycle, including those that are not reversible, because some energy will always be lost as heat.
So, to answer your question, it is not possible to develop a reversible heat-engine cycle that is more efficient than a Carnot cycle operating between the same temperature limits. The efficiency of the Carnot cycle is the maximum possible efficiency for any heat-engine cycle, and this is due to the laws of thermodynamics.
The Carnot cycle represents the most efficient cycle for a heat engine, as it is an idealized process that assumes reversible operations. Any other reversible heat-engine cycle would have the same efficiency as the Carnot cycle or lower efficiency, but never higher.
To know more about Carnot cycle visit:-
https://brainly.com/question/31645644
#SPJ11
A certain common hydrometer weighs 0.125N and the area of cross-section is 10^-4m^2. Calculate the distance between 1.00 and 0.80 markings on the stem
The distance between 1.00 and 0.80 markings on the stem will be 0.45 m.
To solve this problem, we need to use the principle of flotation,
"When a hydrometer is placed in a fluid, it floats at a level where the weight of the hydrometer is equal to the weight of the fluid displaced by the hydrometer."
The distance between the 1.00 and 0.80 markings on the stem corresponds to the volume of fluid displaced by the hydrometer.
Let's assume that the hydrometer floats in water, which has a density of 1000 kg/m³.
Given, weight of the hydrometer = 0.125 N,
So, the volume of water displaced by the hydrometer is:
Volume of water = Weight of hydrometer / Density of water
= (0.125 N) / (1000 kg/m³)
= 0.000125 m³
Since the area of cross-section of the hydrometer is 10⁻⁴ m², the height of water displaced by the hydrometer is:
height of water = volume of water / area of cross-section
= 0.000125 m³ / 10⁻⁴ m²
= 1.25 m
Therefore, the distance between the 1.00 and 0.80 markings on the stem corresponds to a height of 1.25 m - 0.80 m = 0.45 m.
Learn more about hydrometer here
brainly.com/question/24293320
#SPJ1
if the hydraulic piston exerts a 18 knkn force on the arm at bb , what is the arm's angular acceleration?
Angular acceleration is the rate at which the angular velocity of an object changes over time. It is denoted by the symbol alpha (α) and is expressed in units of radians per second squared (rad/s²).
To calculate the arm's angular acceleration, we need to know the moment of inertia and torque acting on the arm. The moment of inertia is a measure of an object's resistance to rotational motion and depends on the shape and mass distribution of the object. The torque is the product of the force and the distance from the point of rotation at which the force is applied.
Once we know these values, we can use the equation:
α = τ / I
where α is the angular acceleration, τ is the torque, and I is the moment of inertia.
Therefore, without knowing the moment of inertia and torque acting on the arm, we cannot determine the arm's angular acceleration.
To know more about Angular acceleration click this link -
brainly.com/question/29428475
#SPJ11
The place the Sun stops its northward motion along the ecliptic is the
A) equator.
B) prime meridian.
C) summer solstice.
D) vernal equinox.
The place where the Sun stops its northward motion along the ecliptic is the summer solstice.
The summer solstice occurs around June 21st in the Northern Hemisphere and marks the longest day and shortest night of the year. During this time, the Sun reaches its highest point in the sky and appears to stand still or "solstice" (from the Latin words "sol" for Sun and "sistere" for standing still) for a brief period before its direction changes.
At the summer solstice, the Sun's declination is at its maximum value, which means it is at its farthest point north of the celestial equator. After the summer solstice, the Sun begins its southward motion along the ecliptic, leading to shorter days and longer nights as it moves towards the autumnal equinox.
Therefore, the correct answer is C) summer solstice.
To know more about hemisphere please visit:
https://brainly.com/question/501939
#SPJ11
7.an electrician uses a clamp-on ammeter and a voltmeter to measure the current and voltage of a motor. if the two values are multiplied, is the product the true power or the apparent power?
No, multiplying the current and voltage readings obtained using a clamp-on ammeter and a voltmeter does not give the true power of a motor.
The product of current and voltage gives the apparent power of the motor, which is the product of the voltage and current that are delivered to the motor, without considering the phase angle between them.
To determine the true power of a motor, the electrician needs to measure the power factor, which is the ratio of the true power to the apparent power. The power factor takes into account the phase angle between the voltage and current, which can affect the efficiency of the motor.
Once the power factor is known, the true power of the motor can be calculated by multiplying the apparent power by the power factor. Alternatively, if the motor's resistance and reactance are known, the true power can be calculated using other formulas that take into account these values.
In summary, to accurately measure the power of a motor, an electrician needs to use a combination of instruments that can measure voltage, current, and power factor.
Learn more about voltmeter
https://brainly.com/question/8505839
#SPJ4
a class a amplifier has an 8 v pp output that is being applied to a 200 ω load. what is the total ac load power? 640 mw 40 mw 320 mw 80 mw
A class A amplifier has an 8 v pp output that is being applied to a 200 ω load. The total AC load power is 80 mW.
The given output voltage of the class A amplifier is 8 V peak-to-peak. The peak voltage is given by:
Vp = Vpp/2 = 8/2 = 4 V
The RMS voltage is given by:
Vrms = Vp/√2 = 4/√2 = 2.828 V
Using Ohm's law, the current in the load is:
I = Vrms/R = 2.828/200 = 0.01414 A
The power in the load is given by:
P = I^2 * R = 0.01414^2 * 200 = 0.040 mW
However, this is only the power for one-half of the AC cycle. The total AC load power is given by:
Ptotal = 2 * P = 2 * 0.040 = 0.080 mW = 80 mW.
To learn more about AC click here
https://brainly.com/question/2397982
#SPJ11
to find the focal point of the lens, a. move the viewing screen until the image is upright b. move the viewing screen until no image is formed c. move the viewing screen until the image is inverted
To find the focal point of a lens, move the viewing screen until the image is either upright or inverted. The focal point is reached when a clear and sharp image is formed.
The focal point of a lens is the point where parallel rays of light converge or appear to diverge from after passing through the lens. To find the focal point, you can adjust the position of the viewing screen until you achieve a clear and sharp image.
In the case where you move the viewing screen until the image is upright, you are looking for the position where the image formed by the lens is upright and in focus. This position corresponds to the focal point of the lens, where the light rays converge to form the image.
On the other hand, if you move the viewing screen until the image is inverted, you are still seeking the focal point. In this case, the image formed by the lens appears inverted, indicating that the light rays have crossed and converged at the focal point.
However, if you move the viewing screen to a position where no image is formed, it suggests that the screen is either too close or too far from the lens. This position does not correspond to the focal point, as no clear image is obtained.
Therefore, by adjusting the position of the viewing screen until an upright or inverted image is achieved, you can determine the location of the focal point of the lens.
Learn more about focal point : brainly.com/question/11210390
#SPJ11
in solar heating applications, heat is stored in some medium until it is needed (i.e., to heat a home at night). should this medium have a high or low specific heat? explain.
In solar heating applications, it is desirable for the medium used to store heat to have a high specific heat. This is because the specific heat of a substance is the amount of heat energy required to raise the temperature of a unit mass of the substance by one degree Celsius. Therefore, a substance with a high specific heat can absorb a large amount of heat energy without a significant increase in temperature. This means that a high specific heat medium can store a large amount of heat energy while remaining at a relatively constant temperature, which is ideal for efficient heat storage. In contrast, a medium with a low specific heat would require a large increase in temperature to store the same amount of heat energy, which could result in thermal losses and reduced efficiency.
For more question like solar heating applications visit the link below:
https://brainly.com/question/31453475
#SPJ11
which explanation of the solar system best fits the observations of the planets and how they orbit the sun?responses
The heliocentric model of the solar system best fits the observations of the planets and their orbits around the Sun, and is widely accepted as the most accurate scientific explanation of our solar system.
The most widely accepted scientific explanation of the solar system is the heliocentric model, which was first proposed by the Polish astronomer Nicolaus Copernicus in the 16th century. This model states that the Sun is at the center of the solar system and the planets orbit around it.
The heliocentric model fits the observations of the planets and their orbits around the Sun better than the previous geocentric model, which placed the Earth at the center of the universe with the planets, including the Sun, orbiting around it. The heliocentric model explains the observations of the planets' retrograde motion, where planets appear to move backward in the sky at certain times, which was difficult to explain in the geocentric model.
The heliocentric model is supported by a wealth of evidence, including observations of the planets and their orbits, as well as the laws of motion and gravity discovered by Sir Isaac Newton. The model has also been refined over time to account for new observations and discoveries, such as the existence of asteroids and comets.
To know more about solar system.
https://brainly.com/question/18365761
#SPJ4
you build a circuit with three incandescent bulbs in parallel one day in the phys 251 laboratory. bulbs 1 and 2 are identical, but bulb 3 has a larger resistance. bulb 1 burns out (becomes a break). we can say that:
If bulb 1 burns out in a parallel circuit with three incandescent bulbs, bulbs 2 and 3 will remain lit, but the overall resistance of the circuit will decrease, resulting in an increase in the total current flowing through the circuit.
In a parallel circuit, each bulb has its own path to the power supply, so if one bulb burns out, the current can still flow through the other bulbs. Bulbs 2 and 3 in this case will remain lit because they are still receiving the same voltage as before, but the overall resistance of the circuit will decrease due to the absence of bulb 1. This is because the resistance of the circuit is determined by the sum of the individual resistances of each bulb, and with one bulb removed, the total resistance of the circuit decreases.
Since the voltage across the circuit remains the same, the decrease in resistance results in an increase in the total current flowing through the circuit, which can cause the remaining bulbs to become brighter than they were before. It is important to note that the increase in current could potentially cause bulb 3 to burn out faster than it would have if all three bulbs were still functioning, as it is the bulb with the larger resistance and therefore may not be able to handle the increased current.
Learn more about resistance here:
brainly.com/question/17044230
#SPJ11
a uniform ball is released from rest on a no-slip surface, as shown in the figure. after reaching its lowest point, the ball begins to rise again, this time on a frictionless surface. when the ball reaches its maximum height on the frictionless surface, it is
the height of the highest point above the no-slip surface is equal to the height of the lowest point.
When the uniform ball is released from rest on a no-slip surface and reaches its lowest point, all of its potential energy is converted to kinetic energy. At the lowest point, the ball's kinetic energy is maximum and its potential energy is minimum.
As the ball begins to rise again on the frictionless surface, its kinetic energy is converted to potential energy. At the highest point, the ball's potential energy is maximum and its kinetic energy is minimum.
The total mechanical energy of the ball, which is the sum of its kinetic energy and potential energy, is conserved throughout the motion. Therefore, the ball's potential energy at the highest point is equal to its kinetic energy at the lowest point:
mgh = (1/2)mv^2
where m is the mass of the ball, h is the height of the highest point above the no-slip surface, and v is the velocity of the ball at the lowest point.
Since the ball is released from rest, its velocity at the lowest point is:
v = sqrt(2gh)
Substituting this into the previous equation, we get:
mgh = (1/2)mv^2 = (1/2) m (2gh) = mgh
Therefore, the height of the highest point above the no-slip surface is equal to the height of the lowest point. So, when the ball reaches its maximum height on the frictionless surface, it is at the same height as its release point on the no-slip surface.
Visit to know more about No slip surface:-
brainly.com/question/1593442
#SPJ11
water travels through a pipe at 15.2 m/s. the pipe contracts from a cross sectional area of 1.4 m2 to an area of 0.280 m2. what is the speed of the water in the second part of the pipe in m/s?
The speed of the water in the second part of the pipe is 76 m/s.
According to the principle of conservation of mass, the mass of water flowing through the pipe will remain constant. As the pipe contracts, the speed of the water will increase to maintain this principle. We can use the equation of continuity to solve for the speed of water in the second part of the pipe.
The equation of continuity states that the product of the cross-sectional area and the speed of the fluid is constant along the length of the pipe. Mathematically, we can express it as A1v1 = A2v2, where A1 and v1 are the cross-sectional area and speed of the water in the first part of the pipe, and A2 and v2 are the cross-sectional area and speed of the water in the second part of the pipe.
Substituting the given values, we get:
1.4 x 15.2 = 0.280 x v2
v2 = (1.4 x 15.2) / 0.280
v2 = 76 m/s (rounded to two decimal places)
Therefore, the speed of the water in the second part of the pipe is 76 m/s.
learn more about cross-sectional area Refer: https://brainly.com/question/13945652
#SPJ11
Why must the amplitudes of the energy eigenfunctions in the finite depth box and in the adjoining barrier regions have the same value at the boundary?
The amplitudes of the energy eigenfunctions in the finite depth box and in the adjoining barrier regions must have the same value at the boundary due to boundary conditions.
When solving for the energy eigenfunctions in a finite depth box and adjoining barrier regions, it is important to consider the boundary conditions. At the boundary between the finite depth box and the adjoining barrier regions, the wave function must be continuous and its derivative must be continuous. This means that the amplitudes of the wave function in the two regions must be equal at the boundary. If the amplitudes were not equal, the wave function would not be continuous, violating the boundary conditions and leading to unphysical results.
To learn more about eigenfunctions, click here:
https://brainly.com/question/31391312
#SPJ11
Calculate the energy released if U 238-nucleus emits an α−particle.ORCalculate the energy released in MeV in the following nuclear reaction92238U→ 90234Th+ 24He+QGiven Atomic mass of 238U=238.05079uAtomic mass of 234Th=234.04363uAtomic mass of alpha particle =4.00260u1u=931.5MeV/c 2Is the decay spontaneous ? Give reasons.
The energy released in the alpha decay of U-238 is 4.24 MeV. The decay of U-238 is a spontaneous process because the mass of the reactant is greater than the sum of the masses of the products, resulting in a release of energy during the decay. Additionally, the alpha particle produced in the decay is a stable nucleus and does not require further decay.
The energy released in the alpha decay of U-238 can be calculated using the mass-energy equivalence principle, which states that the energy released in a nuclear reaction is equal to the difference in mass between the reactants and the products, multiplied by the speed of light squared (c^2).
The reaction for the alpha decay of U-238 is:
^238U → ^234Th + ^4He
The mass difference between the reactant and the products can be calculated as:
Mass of reactant - (mass of ^234Th + mass of ^4He)
= 238.05079 u - (234.04363 u + 4.00260 u)
= 0.00456 u
The energy released in the reaction can be calculated as:
Energy = (0.00456 u) * (931.5 MeV/c^2/u) * (c^2)
= 4.24 MeV
Therefore, the energy released in the alpha decay of U-238 is 4.24 MeV.
To know more about alpha decay, click here:
https://brainly.com/question/27870937
#SPJ11
A 560 g , 8.5-cm-diameter can is filled with uniform, dense food. It rolls across the floor at 1.2 m/s . Part A What is the can's kinetic energy?
The kinetic energy of the can is 0.4032 J, calculated using the formula [tex]$KE = \frac{1}{2}mv^2$[/tex], where m is the mass of the object and v is its velocity. The diameter of the can is not relevant, and the calculation assumes purely translational motion.
The kinetic energy of an object is the energy that it possesses by virtue of its motion. It is given by the formula [tex]$KE = \frac{1}{2}mv^2$[/tex], where m is the mass of the object and v is its velocity.
In this case, the can have a mass of 560 g, which is 0.56 kg. Its velocity is 1.2 m/s. To calculate its kinetic energy, we can plug these values into the formula:
[tex]$KE = \frac{1}{2}mv^2 = \frac{1}{2} \times 0.56 , \text{kg} \times (1.2 , \text{m/s})^2 = 0.4032 , \text{J}$[/tex]
Therefore, the can has a kinetic energy of 0.4032 joules.
It's worth noting that the diameter of the can is not relevant to the calculation of its kinetic energy. The mass and velocity of the object are the only variables needed to determine its kinetic energy.
To learn more about kinetic energy
https://brainly.com/question/999862
#SPJ4
based on your answer to part a, which of the following best describes why the distance from earth to the galaxy increases as the balloon expands?
The distance from Earth to the galaxy increases as the balloon expands because of the expansion of space.
As the balloon expands, it stretches the space between galaxies, causing them to move further away from each other. This expansion of space is a fundamental property of the universe and is responsible for the observed redshift of light from distant galaxies. As a result, the further away a galaxy is from us, the faster it appears to be moving away due to the expansion of space. This is known as Hubble's law and is one of the key pieces of evidence for the Big Bang theory.
To learn more about galaxy:
https://brainly.com/question/31361315
#SPJ11
5.0 a of current flows with uniform current density through a wire of 3.0 mm diameter. at what two radii is the magnetic field 3.33 gauss (3.33x10-4 t)? [8 pts]
The magnetic field is 3.33 Gauss at radii of 8.9 mm and 3.8 mm from the center of the wire.
We can use Ampere's Law to find the magnetic field at a distance r from the center of the wire:
∮B·dl = μ₀I,
where B is the magnetic field, dl is a differential element of length around a closed loop, μ₀ is the permeability of free space, and I is the current.
Since the current density J is uniform, we have:
I = JA,
where A is the cross-sectional area of the wire.
For a wire of diameter d, we have:
A = π(d/2)² = πd²/4
So, I = Jπd²/4.
Using these expressions and solving for B, we obtain:
B = μ₀Jr/2
where r is the distance from the center of the wire.
Setting B = 3.33x10⁻⁴ T, we can solve for the values of r:
3.33x10⁻⁴ = 4πx10⁻⁷ x 5.0 x (r/1.5) / 2
r = 0.0089 m = 8.9 mm and r = 3.8 mm.
To learn more about current density click on,
https://brainly.com/question/30889804
#SPJ4
A 180 mW vertically polarized laser beam passes through a polarizing filter whose axis is 39 ∘ from horizontal.What is the power of the laser beam as it emerges from the filter?Express your answer to two significant figures and include the appropriate units.
A 180 mW vertically polarized laser beam passes through a polarizing filter whose axis is 39 ∘ from horizontal.What is the power of the laser beam as it emerges from the filter is 140 mW.
To calculate the power of the laser beam as it emerges from the filter, we need to use the Malus' Law formula:
P_out = P_in * cos²θ
Where:
P_out is the power of the laser beam after passing through the filter,
P_in is the initial power of the laser beam (180 mW),
θ is the angle between the polarization direction of the laser beam and the axis of the filter (39°).
Now, let's plug in the values:
P_out = 180 mW * cos²(39°)
Using a calculator, we find that:
cos²(39°) ≈ 0.758
Therefore:
P_out = 180 mW * 0.758 ≈ 136.44 mW
Expressing the answer to two significant figures and including the appropriate units, we have:
P_out ≈ 140 mW.
To know more about malus law visit:
https://brainly.com/question/14177847
#SPJ11
when current passes through a series combination of resistors, does the current get smaller as it goes through each successive resistor in the combination?
Yes, the current does get smaller as it goes through each successive resistor in a series combination.
This is due to the fact that the total resistance in a series circuit is equal to the sum of all the individual resistances. As the total resistance increases, the current must decrease in order to maintain a constant voltage. This is known as Ohm's Law, which states that the current through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance between them. So, in a series combination of resistors, the current will be highest at the beginning of the circuit and gradually decrease as it passes through each resistor.
The current flowing through a circuit with a series of resistors stays constant throughout the circuit. Kirchhoff's Current Law, which stipulates that the total current entering and exiting a junction are equal, is responsible for this.
The resistance of each resistor in the series prevents the electricity from flowing freely as it passes through them. This indicates that while the voltage across each resistor varies, the current that flows through each resistor is constant.
Learn more about series here
https://brainly.com/question/31824630
#SPJ11
when a heat pump is used to heat a house in the winter, how will the coefficient of performance be affected if the inside set temperature is changed from 65 of to 70 of?
When the inside set temperature is increased from 65°F to 70°F, the coefficient of performance of a heat pump will decrease
. This is because as the temperature difference between the inside and outside decreases, the efficiency of the heat pump decreases. The coefficient of performance is defined as the ratio of the heat output (i.e. heat supplied to the house) to the work input (i.e. electrical energy consumed by the heat pump).
As the temperature difference between the inside and outside decreases, more work is required to extract the same amount of heat, resulting in a lower coefficient of performance.
Learn more about temperature
https://brainly.com/question/7510619
#SPJ4
Explain through an example that velocity of sound is more in solids as compared
to that in air.
That they are faster in solids than in air. and this is because of the fact that the density of the solids is more than that of air, which helps waves to move faster in solids.
For example:if you hear the sound of a train from the tracks and the air and compare them, the sound in the air will reach you late than that of the tracks.
It means if the tracks get sound at the time ‘x’ then the sound you hear through air will be much more than x.
6. Which color of light has a longer wavelength: red or green?
Answer:
Red
Explanation:
The visible colors from shortest to longest wavelength are: violet, blue, green, yellow, orange, and red.
So red has a longer wavelength than green.