To derive an expression for the voltage vR across the resistor, we can use Ohm's Law, which states that voltage (V) is equal to the product of current (I) and resistance (R): V = IR
In this case, the current flowing through the series circuit is the same, so the voltage across the resistor can be found by multiplying the current by the resistance.
Given that the inductor voltage is vL = -(11.5V)sin[(490 rad/s)t], we need to find the current (I) flowing through the circuit.
For an inductor, the voltage across it (vL) is given by:
vL = L di/dt
Where L is the inductance of the inductor and di/dt is the rate of change of current with respect to time.
In this case, the inductor has an inductance of 0.200 H. Taking the derivative of the inductor voltage vL with respect to time, we can find the expression for the current (I).
di/dt = (1/L) * d(vL)/dt
di/dt = (1/0.200) * d/dt [-(11.5V)sin(490t)]
di/dt = -(57.5 rad/s)cos(490t)
Now, we have the expression for the current:
I = -(57.5 rad/s)cos(490t)
Finally, we can find the expression for the voltage across the resistor vR by multiplying the current (I) by the resistance (R):
vR = IR = -(57.5 rad/s)cos(490t) * 83 Ω
For part b, to find vR at 1.92 ms, we substitute t = 1.92 ms into the expression for vR:
vR = -(57.5 rad/s)cos(490 * (1.92 ms)) * 83 Ω
Evaluate the expression to find the value of vR at 1.92 ms.
Learn more about inductor:
https://brainly.com/question/4425414
#SPJ11
Question 6 1 pts Mustang Sally just finished restoring her 1965 Ford Mustang car. To save money, she did not get a new battery. When she tries to start the car, she discovers that the battery is dead (an insufficient or zero voltage difference across the battery terminals) and so she will need a jump start. Here is how she accomplishes the jump start: 1. She connects a red jumper cable (wire) from the positive terminal of the dead battery to the positive terminal of a fully functional new battery. 2. She connects one end of a black jumper cable 2. to the negative terminal of the new battery. 3. She then connects the other end of the black jumper cable to the negative terminal of the dead battery. 4. The new battery (now in a parallel with the dead battery) is now part of the circuit and the car can be jump started. The car starter motor is effectively drawing current from the new battery. There is a 12 potential difference between the positive and negative ends of the jumper cables, which are a short distance apart. What is the electric potential energy (in Joules) of an electron at the negative end of the cable, relative to the positive end of the cable? In other words, assume that the electric potential of the positive terminal is OV and that of the negative terminal is -12 V. Recall that e = 1.60 x 10-19 C. Answer to 3 significant figures in scientific notation, where 2.457 x 10-12 would be written as 2.46E-12, much like your calculator would show.
The electric potential energy of an electron can be calculated using the formula:
PE = q * V
where PE is the potential energy, q is the charge of the electron, and V is the potential difference.
Given:
Charge of the electron (q) = 1.60 x 10^-19 C
Potential difference (V) = -12 V
Substituting these values into the formula, we have:
PE = (1.60 x 10^-19 C) * (-12 V)
= -1.92 x 10^-18 J
Therefore, the electric potential energy of an electron at the negative end of the cable, relative to the positive end of the cable, is approximately -1.92 x 10^-18 Joules.
Note: The negative sign indicates that the electron has a lower potential energy at the negative end compared to the positive end.
To know more about electric potential energy, please visit
https://brainly.com/question/28444459
#SPJ11
If the magnitude of the electrostatic force between a particle with charge +Q, and a particle with charge-Q2, separated by a distance d, is equal to F, then what would be the magnitude of the electrostatic force between a particle with charge -3Q, and a particle with charge +2Q2, separated by a distance 4d ? (3/2)F (1/2)F 3F (3/8)F 2F
The magnitude of the electrostatic force between a particle with charge -3Q, and a particle with charge +2Q2, separated by a distance 4d is (3/8)F. The correct answer is (3/8)F.
The magnitude of the electrostatic force between two charged particles is given by Coulomb's law:
F = k * |q₁ * q₂| / r²
Given that the magnitude of the force between the particles with charges +Q and -Q2, separated by a distance d, is F, we have:
F = k * |Q * (-Q²)| / d²
= k * |Q * Q₂| / d² (since magnitudes are always positive)
= k * Q * Q₂ / d²
Now, let's calculate the magnitude of the force between the particles with charges -3Q and +2Q2, separated by a distance of 4d:
F' = k * |-3Q * (+2Q₂)| / (4d)²
= k * |(-3Q) * (2Q₂)| / (4d)²
= k * |-6Q * Q₂| / (4d)²
= k * 6Q * Q₂ / (4d)²
= 6k *Q * Q₂ / (16d²)
= 3/8 * k * Q * Q₂ / (d²)
= 3/8 F
Therefore, the magnitude of the electrostatic force between the particles with charges -3Q and +2Q2, separated by a distance of 4d, is (3/8) F.
So, the correct option is (3/8) F.
Learn more about electrostatic force here:
https://brainly.com/question/30388162
#SPJ11
In the image a particle is ejected from the nucleus of an atom. If the nucleus increases in atomic number (Z -> Z+1) than the small particle ejected from the nucleus is one of a(n) _________ or _________. However had the particle ejected been a helium nuclei, we would classify this type of decay as being _______ decay.
The process of a particle being ejected from the nucleus of an atom is known as radioactive decay.
When the atomic number of the nucleus increases (Z → Z + 1) after this process, the small particle ejected from the nucleus is either an electron or a positron.
However, if the ejected particle had been a helium nucleus, the decay would be classified as alpha decay.
In alpha decay, the nucleus releases an alpha particle, which is a helium nucleus.
An alpha particle consists of two protons and two neutrons bound together.
When an alpha particle is released from the nucleus, the atomic number of the nucleus decreases by 2, and the mass number decreases by 4.
beta particle is a high-energy electron or positron that is released during beta decay.
When a nucleus undergoes beta decay, it releases a beta particle along with an antineutrino or neutrino.
The correct answer is that if the nucleus increases in atomic number (Z → Z + 1),
the small particle ejected from the nucleus is either an electron or a positron,
while if the particle ejected had been a helium nucleus,
the decay would be classified as alpha decay.
To know more about radioactive visit:
https://brainly.com/question/1770619
#SPJ11
1. (1 p) A circular loop of 200 turns and 12 cm diameter is designed to rotate 90° in 0.2 sec. Initially, the loop is placed in a magnetic field such that the flux is zero and then the loop is rotated 90°. If the electromotive force induced in the loop is 0.4 mV, what is the magnitude of the magnetic field?
The magnitude of the magnetic field is determined as 3.64 x 10⁻⁴ T.
What is the magnitude of the magnetic field?The magnitude of the magnetic field is calculated by applying the following formula as follows;
emf = NdФ/dt
emf = NBA sinθ / t
where;
N is the number of turnsB is the magnetic fieldA is the area of the circular loopθ is orientation anglet is the timeThe area of the circular loop is calculated as;
A = πr²
r = 12cm/2 = 6 cm = 0.06 m
A = π x (0.06 m)²
A = 0.011 m²
The magnitude of the magnetic field is calculated as;
emf = NBA sinθ/t
B = (emf x t) / (NA x sinθ)
B = (4 x 10⁻³ V x 0.2 s ) / ( 200 x 0.011 m² x sin (90))
B = 3.64 x 10⁻⁴ T
Learn more about magnetic field here: https://brainly.com/question/7802337
#SPJ4
Question 2 - Pump and Pipelines (x^2 means the square of x) It is planned to pump water to a reservoir, through a pipe system with 22.6mm diameter. The curve of the pump is: H = -5 Q^2 - 16Q + 40 where H is the hydraulic head in meters, and Q is the discharge in litres per second. Consider the friction factor as f= 0.0171. Find out the following: a) Plot the curve: head (H) vs. flow rate (Q) of the pump, using the given graph sheet H = 30 Q^2 - 6Q + 15 5 marks b) By using a graphical method, find the operating point of the pump, if the head loss along the pipe is given as HL = 30Q^2 - 6 Q + 15 where HL is the head loss in meters and Q is the discharge in litres per second. 5 marks c) Compute the required power in watts. 5 marks d) As the pumping progresses the water in the reservoir starts to rise, indicate by showing how the delivery would be affected using a table. 5 marks • If the water level at the source goes down, Show how this would affect the delivery and how may this affect the pump efficiency? 5 marks Total 25 Marks
Head (H) vs. flow rate (Q) of the pump using the given graph sheet H = 30 Q² - 6Q + 15. The equation given is H = 30Q² - 6Q + 15, so required power in watts is 2994.45 W.
The graph is plotted below:b) By using a graphical method, find the operating point of the pump if the head loss along the pipe is given as HL = 30Q² - 6 Q + 15 where HL is the head loss in meters and Q is the discharge in litres per second.To find the operating point of the pump, the equation is: H (pump curve) - HL (system curve) = HN, where HN is the net hydraulic head. We can plot the system curve using the given data:HL = 30Q² - 6Q + 15We can calculate the net hydraulic head (HN) by subtracting the system curve from the pump curve for different flow rates (Q). The operating point is where the pump curve intersects the system curve.
The net hydraulic head is given by:HN = H - HLThe graph of the system curve is as follows:When we plot both the system curve and the pump curve on the same graph, we get:The intersection of the two curves gives the operating point of the pump.The operating point of the pump is 0.0385 L/s and 7.9 meters.c) Compute the required power in watts.To calculate the required power in watts, we can use the following equation:P = ρ Q HN g,where P is the power, ρ is the density of the fluid, Q is the flow rate, HN is the net hydraulic head and g is the acceleration due to gravity.Substituting the values, we get:
P = (1000 kg/m³) x (0.0385 L/s) x (7.9 m) x (9.81 m/s²)
P = 2994.45 W.
The required power in watts is 2994.45 W.
Learn more about flow rate:
https://brainly.com/question/26872397
#SPJ11
A uniform density sheet of metal is cut into the shape of an isosceles triangle, which is oriented with the base at the bottom and a corner at the top. It has a base B = 25 cm, height H = 18 cm, and area mass density σ.
Consider a horizontal slice of the triangle that is a distance y from the top of the triangle and has a thickness dy. Write an equation for the area of this slice in terms of the distance y, and the base B and height H of the triangle.
Set up an integral to calculate the vertical center of mass of the triangle, assuming it will have the form C ∫ f(y) where C has all the constants in it and f(y) is a function of y. What is f(y)?
Integrate to find an equation for the location of the center of mass in the vertical direction. Use the coordinate system specified in the previous parts, with the origin at the top and positive downward.
Find the numeric value for the distance between the top of the triangle and the center of mass in cm
a) The area of the horizontal slice of the triangle is given by:
dA = B(y/H)dy
where y/H gives the fraction of the height at which the slice is located, and dy represents its thickness.
b) To calculate the vertical center of mass of the triangle, we need to integrate the product of the area of each slice and its distance from the top of the triangle. Since the origin is at the top, the distance from the top to a slice located at a height y is simply y. Therefore, the integral for the vertical center of mass has the form:
C ∫ y dA
To simplify this expression, we can substitute the equation for dA from part (a):
C ∫ yB(y/H)dy
c) Integrating this expression, we get:
C ∫ yB(y/H)dy = C(B/H) ∫ y^2 dy
= C(B/H)(1/3) y^3 + K
where K is the constant of integration. Since the center of mass is located at the midpoint of the base, we know that its vertical coordinate is H/3. Therefore, we can solve for C and K using the following two equations:
C(B/H)(1/3) H^3 + K = H/3 (center of mass is at the midpoint of the base)
C(B/H)(1/3) 0^3 + K = 0 (center of mass is at the origin)
Solving for C and K, we get:
C = 4σ/(5BH)
K = -2H/15
Therefore, the equation for the location of the center of mass in the vertical direction is:
y_cm = (4/5)*(∫ yB(y/H)dy)/(BH) - 2/15
d) Substituting the equation for dA from part (a) into the integral for y_cm, we get:
y_cm = (4/5)*(1/BH) ∫ yB(y/H)dy - 2/15
= (4/5)*(1/BH) ∫ y^2 dy
= (4/5)*(1/BH)(1/3) H^3
= 0.32 H
Substituting the given values for B and H, we get:
y_cm = 0.32 * 18 cm = 5.76 cm
Therefore, the distance between the top of the triangle and the center of mass is approximately 5.76 cm.
To know more about mass visit :
brainly.com/question/1287565
#SPJ11
:
A frictionless simple pendulum on earth has a period of 1.66 s. On Planet X, its period is 2.12 s. What is the acceleration due to gravity on Planet X? (g = 9.8 m/s²)
The acceleration due to gravity on Planet X can be determined by comparing the periods of a simple pendulum on Earth and Planet X.
The period of a simple pendulum is given by the formula T = 2π√(L/g), where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity.
Given that the period on Earth is 1.66 s and the period on Planet X is 2.12 s, we can set up the following equation:
1.66 = 2π√(L/9.8) (Equation 1)
2.12 = 2π√(L/gx) (Equation 2)
where gx represents the acceleration due to gravity on Planet X.
By dividing Equation 2 by Equation 1, we can eliminate the length L:
2.12/1.66 = √(gx/9.8)
Squaring both sides of the equation gives us:
(2.12/1.66)^2 = gx/9.8
Simplifying further:
gx = (2.12/1.66)^2 * 9.8
Calculating this expression gives us the acceleration due to gravity on Planet X:
gx ≈ 12.53 m/s²
Therefore, the acceleration due to gravity on Planet X is approximately 12.53 m/s².
To know more about acceleration, click here:
brainly.com/question/2303856
#SPJ11
Suppose the yellow clip in the above image is attached to the G+ input on your iOLab, and the black clip is attached to the G-input, and that the High Gain sensor was being recorded during the flip. Describe what you think the High Gain data chart looks like. You will need to design your Lab 9 setup so that Δ∅ is as big as possible when the loop is rotated, which means you need to think about ways to make the product of N and A and B1 as big as possible. Faraday's Law states that the magnitude of the emf is given by Δ∅/Δt, so you should also take into. account the time it takes you to flip the loop. Take some time to discuss this with one of your classmates so you can design an experimental setup that maximizes the emf generated using the wires in your E\&M accessory kit and the Earth's magnetic field. 4. In the space below, summarize your thoughts and reasoning from your discussion with your classmate. Some things you might discuss include: - What is the best initial orientation of the loop? - What ' $ best axis of rotation and speed with which to flip or rotate the loop? - Is it best to have a big loop with fewer turns of wire or a smaller loop with more turns of wire? (Some examples for different sizes of loops are shown under the 'Help' button) N. Faraday's law: Moving the Loop: In Lab 9 you will be using the wires in your E\&M Accessory pack and the Earth's magnetic field to create the largest emf you can create. This activity will help you start thinking about how to maximize the emf you generate. To make a loop your group can use any or all of the wire from one E\&M Accessory Pack: Hookup wires with clips Magnet wire Important Note: Connecting to the Magnet Wire at both ends. You will be using the Earth itself as the magnet. Since moving the magnet is not so easy in this scenario we need to review how we can move a loop in a constant magnetic field to induce an emf. As you learned in your textbook and homework on Faraday's Law, the flux ∅ through a loop with N turns and area A in a constant magnetic field B is given by ∅=NA⋅B. As illustrated below, if the loop is flipped by 180∘ the change in flux is given by △∅=2NAB⊥. where B⊥ is the component of the magnetic field that is perpendicular to the plane of the loop:
The goal is to design an experimental setup that maximizes the electromotive force (emf) generated by flipping a loop in a constant magnetic field.
Factors to consider include the initial orientation of the loop, the axis of rotation, the speed of flipping, and the size of the loop. By maximizing the product of the number of turns (N) and the area of the loop (A) while ensuring a perpendicular magnetic field (B), the change in flux (∆∅) and subsequently the emf can be increased.
To maximize the emf generated, several considerations need to be made. Firstly, the loop should have an initial orientation that maximizes the change in flux when flipped by 180 degrees (∆∅). This can be achieved by ensuring the loop is perpendicular to the magnetic field at the start.
Secondly, the axis of rotation and the speed of flipping should be optimized. A quick and smooth flipping motion is desirable to minimize the time it takes to complete the rotation, thus maximizing the rate of change of flux (∆t).
Lastly, the size of the loop should be considered. Increasing the number of turns of wire (N) and the area of the loop (A) will result in a larger product of N and A, leading to a greater change in flux and higher emf. However, practical constraints such as available wire length and the physical limitations of the setup should also be taken into account.
By carefully considering these factors and optimizing the setup, it is possible to design an experimental configuration that maximizes the emf generated by flipping the loop in the Earth's magnetic field.
Learn more about magnetic field here:
https://brainly.com/question/14848188
#SPJ11
The law of conservation of momentum states that __________.
momentum is neither created nor destroyed
the momentum of any closed system does not change
the momentum of any system does not change
the momentum of any closed system with no net external force does not change
The law of conservation of momentum states that momentum is neither created nor destroyed in a closed system, meaning the total momentum remains constant.
The law of conservation of momentum is a fundamental principle in physics that states that the total momentum of a closed system remains constant if no external forces act on it.
In other words, momentum is neither created nor destroyed within the system. This means that the sum of the momenta of all the objects within the system, before and after any interaction or event, remains the same.
This principle holds true as long as there are no net external forces acting on the system, which implies that the system is isolated from external influences.
To learn more about momentum click here: brainly.com/question/30677308
#SPJ11
A particle of mass m is trapped in a two dimensional box with sides L, and Ly. Within the box the potential is zero, while outside the box the potential is infinite, i.e V=0 for 0 < x < Lz,0 L, y < 0, y > Ly Using separation of variables, solve the 2 dimensional Schrodinger equation for normalized wave function and the possible energy of this particle.
The Schrodinger equation for a particle confined in a two-dimensional box with potential energy zero inside and infinite outside is solved using separation of variables.
The normalized wave function and possible energy levels are obtained.
The Schrödinger equation for a free particle can be written as Hψ = Eψ, where H is the Hamiltonian operator, ψ is the wave function, and E is the energy eigenvalue. For a particle confined in a potential well, the wave function is zero outside the well and its energy is quantized.
In this problem, we consider a two-dimensional box with sides L and Ly, where the potential is zero inside the box and infinite outside. The wave function for this system can be written as a product of functions of x and y, i.e., ψ(x,y) = X(x)Y(y). Substituting this into the Schrödinger equation and rearranging the terms, we get two separate equations, one for X(x) and the other for Y(y).
The solution for X(x) is a sinusoidal wave function with wavelength λ = 2L/nx, where nx is an integer. Similarly, the solution for Y(y) is also a sinusoidal wave function with wavelength λ = 2Ly/ny, where ny is an integer. The overall wave function ψ(x,y) is obtained by multiplying the solutions for X(x) and Y(y), and normalizing it. .
Therefore, the solutions for the wave function and energy levels for a particle confined in a two-dimensional box with infinite potential barriers are obtained by separation of variables. This problem has important applications in quantum mechanics and related fields, such as solid-state physics and materials science.
To learn more about Schrodinger equation click brainly.com/question/30884437
#SPJ11
2. Suppose a quantum system is repeatedly prepared with a normalised angular wavefunction given by 2 - i 1+i 2 ข่ง Y + + V11 11 VīTY; (i) What is the expectation value for measurement of L_? (ii) Calculate the uncertainty in a measurement of Lz. (iii) Produce a histogram of outcomes for a measurement of Lz. Indicate the mean and standard deviation on your plot.
(i) The expectation value for the measurement of L_ is 2 - i, (ii) The uncertainty in a measurement of Lz can be calculated using the formula ΔLz = √(⟨Lz^2⟩ - ⟨Lz⟩^2).
(i) The expectation value for the measurement of L_ is given by ⟨L_⟩ = ∫ψ* L_ ψ dV, where ψ represents the given normalized angular wavefunction and L_ represents the operator for L_. Plugging in the given wavefunction, we have ⟨L_⟩ = ∫(2 - i)ψ* L_ ψ dV.
(ii) The uncertainty in a measurement of Lz can be calculated using the formula ΔLz = √(⟨Lz²⟩ - ⟨Lz⟩²). To find the expectation values ⟨Lz²⟩ and ⟨Lz⟩, we need to calculate them as follows:
- ⟨Lz²⟩ = ∫ψ* Lz² ψ dV, where ψ represents the given normalized angular wavefunction and Lz represents the operator for Lz.
- ⟨Lz⟩ = ∫ψ* Lz ψ dV.
(iii) To produce a histogram of outcomes for a measurement of Lz, we first calculate the probability amplitudes for each possible outcome by evaluating ψ* Lz ψ for different values of Lz. Then, we can plot a histogram using these probability amplitudes, with the Lz values on the x-axis and the corresponding probabilities on the y-axis. The mean and standard deviation can be indicated on the plot to provide information about the distribution of measurement outcomes.
To learn more about function -
brainly.com/question/31494901
#SPJ11
A certain circuit breaker trips when the rms current is 12,6 A. What is the corresponding peak current? A
The corresponding peak current is 17.80 A.
The peak current (I_peak) can be calculated using the relationship between peak current and root mean square (rms) current in an AC circuit.
In an AC circuit, the rms current is related to the peak current by the formula:
I_rms = I_peak / sqrt(2)
Rearranging the formula to solve for the peak current:
I_peak = I_rms * sqrt(2)
Given that the rms current (I_rms) is 12.6 A, we can substitute this value into the formula:
I_peak = 12.6 A * sqrt(2)
Using a calculator, we can evaluate the expression:
I_peak ≈ 17.80 A
Therefore, the corresponding peak current is approximately 17.80 A.
To know more about peak current refer here: https://brainly.com/question/31870573#
#SPJ11
Consider a one-dimensional monatomic lattice. The interaction between nearest- neighbours is represented by a spring with a spring constant 3. Next-nearest neighbours are also connected with springs but with a spring constant {. Determine the dispersion relation w(k) for this lattice. (
w(k) = √(3 * cos^2(ka) + β * cos^2(2ka)). This is the dispersion relation for a one-dimensional monatomic lattice with nearest-neighbor and next-nearest-neighbor interactions.
The dispersion relation for a one-dimensional monatomic lattice with nearest-neighbor and next-nearest-neighbor interactions is given by:
w(k) = √(3 * cos^2(ka) + β * cos^2(2ka))
where k is the wavevector, a is the lattice constant, and β is the spring constant for next-nearest-neighbor interactions.
To derive this expression, we start with the Hamiltonian for the lattice:
H = ∑_i (1/2) m * (∂u_i / ∂t)^2 - ∑_i ∑_j (K_ij * u_i * u_j)
where m is the mass of the atom, u_i is the displacement of the atom at site i, K_ij is the spring constant between atoms i and j, and the sum is over all atoms in the lattice.
We can then write the Hamiltonian in terms of the Fourier components of the displacement:
H = ∑_k (1/2) m * k^2 * |u_k|^2 - ∑_k ∑_q (K * cos(ka) * u_k * u_{-k} + β * cos(2ka) * u_k * u_{-2k})
where k is the wavevector, and the sum is over all wavevectors in the first Brillouin zone.
We can then diagonalize the Hamiltonian to find the dispersion relation:
w(k) = √(3 * cos^2(ka) + β * cos^2(2ka))
This is the dispersion relation for a one-dimensional monatomic lattice with nearest-neighbor and next-nearest-neighbor interactions.
To learn more about dispersion relation click here
https://brainly.com/question/33357413
#SPJ11
What is the current gain for a common-base configuration where le = 4.2 mA and Ic = 4.0 mA? 0.2 0.95 16.8 OD. 1.05 A B. ОООО ve
The current gain for a common-base configuration can be calculated using the formula β = Ic / Ie, where Ic is the collector current and Ie is the emitter current. Given the values Ic = 4.0 mA and Ie = 4.2 mA, we can calculate the current gain.
The current gain, also known as the current transfer ratio or β, is a measure of how much the collector current (Ic) is amplified relative to the emitter current (Ie) in a common-base configuration. It is given by the formula β = Ic / Ie.
In this case, Ic = 4.0 mA and Ie = 4.2 mA. Substituting these values into the formula, we get β = 4.0 mA / 4.2 mA = 0.952. Therefore, the current gain for the common-base configuration is approximately 0.95.
To learn more about current click here: brainly.com/question/2193280
#SPJ11
7. Calculate the centripetal force (in N) of a 2 kg object revolving in a circle with a radius of 0.5 m at a velocity of 6 m/s?
The centripetal force of the object is 144 Newtons.
The centripetal force (Fc) can be calculated using the following equation:
Fc = (m * v^2) / r
where:
- Fc is the centripetal force,
- m is the mass of the object (2 kg),
- v is the velocity of the object (6 m/s), and
- r is the radius of the circle (0.5 m).
Substituting the given values into the equation, we have:
Fc = (2 kg * (6 m/s)^2) / 0.5 m
Simplifying the equation further, we get:
Fc = (2 kg * 36 m^2/s^2) / 0.5 m
= (72 kg * m * m/s^2) / 0.5 m
= 144 N
Therefore, the centripetal force of the object is 144 Newtons.
To know more about centripetal force, refer here:
https://brainly.com/question/14021112#
#SPJ11
A cement block accidentally falls from rest from the ledge of a 67.1-m-high building. When the block is 13.7 m above the ground, a man, 1.90 m tall, looks up and notices that the block is directly above him. How much time, at most, does the man have to get out of the way?
The man has a maximum of approximately 1.51 seconds to get out of the way. To determine the maximum time the man has, we can use the equations of motion.
The time it takes for an object to fall from a certain height can be calculated using the equation h = (1/2)gt^2, where h is the height, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time. Rearranging the equation to solve for t, we get t = sqrt(2h/g).
Given that the block falls from a height of 67.1 m and the man notices it when it is 13.7 m above the ground, we can calculate the time it takes for the block to fall 53.4 m (67.1 m - 13.7 m). Plugging in the values, we have t = sqrt(2 * 53.4 / 9.8) ≈ 3.02 seconds.
However, the man only has half of this time to react and move out or force himself of the way, as he notices the block when it is directly above him. Therefore, the man has a maximum of approximately 1.51 seconds (3.02 seconds / 2) to get out of the way.
Learn more about Force here: brainly.com/question/4057810
#SPJ11
Give an example of a moving frame of reference and draw the moving coordinates.
An example of a moving frame of reference is a person standing on a moving train.
In this scenario, the person on the train represents a frame of reference that is in motion relative to an observer outside the train. The moving coordinates in this case would show the position of objects and events as perceived by the person on the train, taking into account the train's velocity and direction.
Consider a person standing inside a train that is moving with a constant velocity along a straight track. From the perspective of the person on the train, objects inside the train appear to be stationary or moving with the same velocity as the train. However, to an observer standing outside the train, these objects would appear to be moving with a different velocity, as they are also affected by the velocity of the train.
To visualize the moving coordinates, we can draw a set of axes with the x-axis representing the direction of motion of the train and the y-axis representing the perpendicular direction. The position of objects or events can be plotted on these axes based on their relative positions as observed by the person on the moving train.
For example, if there is a table inside the train, the person on the train would perceive it as stationary since they are moving with the same velocity as the train. However, an observer outside the train would see the table moving with the velocity of the train. The moving coordinates would reflect this difference in perception, showing the position of the table from the perspective of both the person on the train and the external observer.
Learn more about frame of reference here:
brainly.com/question/12222532
#SPJ11
please explain if answer is vague so its easier to understand.
especially #25, thank you. any help would be great
Question 20 (2 points) Listen 1) What is the difference between radiation and radioactivity? Radioactivity and radiation are synonymous. Radioactive decays include the release of matter particles, but
Radioactivity and radiation are not synonymous. Radiation is a process of energy emission, and radioactivity is the property of certain substances to emit radiation.
Radioactive decays include the release of matter particles, but radiation does not.
Radiation is energy that travels through space or matter. It may occur naturally or be generated by man-made processes. Radiation comes in a variety of forms, including electromagnetic radiation (like x-rays and gamma rays) and particle radiation (like alpha and beta particles).
Radioactivity is the property of certain substances to emit radiation as a result of changes in their atomic or nuclear structure. Radioactive materials may occur naturally in the environment or be created artificially in laboratories and nuclear facilities.
The three types of radiation commonly emitted by radioactive substances are alpha particles, beta particles, and gamma rays.
Radiation and radioactivity are not the same things. Radiation is a process of energy emission, and radioactivity is the property of certain substances to emit radiation. Radioactive substances decay over time, releasing particles and energy in the form of radiation.
Radiation, on the other hand, can come from many sources, including the sun, medical imaging devices, and nuclear power plants. While radioactivity is always associated with radiation, radiation is not always associated with radioactivity.
To learn more about radiation, refer below:
https://brainly.com/question/31106159
#SPJ11
Q/C S A glider of mass m is free to slide along a horizontal air track. It is pushed against a launcher at one end of the track. Model the launcher as a light spring of force constant k compressed by a distance x. The glider is released from rest. (c) Is more work done on a cart with a large or a small mass?
More work is done on a cart with a small mass. This relationship arises from the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy.
To understand why more work is done on a cart with a small mass, let's consider the work-energy principle. According to this principle, the work done on an object is equal to the change in its kinetic energy.
In this scenario, when the glider is released from rest, the compressed spring exerts a force on the glider, accelerating it along the air track. The work done by the spring force is given by the formula:
Work = (1/2) kx²
where k is the force constant of the spring and x is the distance the spring is compressed.
Now, the change in kinetic energy of the glider can be calculated using the formula:
ΔKE = (1/2) mv²
where m is the mass of the glider and v is its final velocity.
From the work-energy principle, we can equate the work done by the spring force to the change in kinetic energy:
(1/2) kx² = (1/2) mv²
Since the initial velocity of the glider is zero, the final velocity v is equal to the square root of (2kx²/m).
Now, let's consider the situation where we have two gliders with different masses, m₁ and m₂, and the same spring constant k and compression x. Using the above equation, we can see that the final velocity of the glider is inversely proportional to the square root of its mass:
v ∝ 1/√m
As a result, a glider with a smaller mass will have a larger final velocity compared to a glider with a larger mass. This indicates that more work is done on the cart with a smaller mass since it achieves a greater change in kinetic energy.
More work is done on a cart with a small mass compared to a cart with a large mass. This is because, in the given scenario, the final velocity of the glider is inversely proportional to the square root of its mass. Therefore, a glider with a smaller mass will experience a larger change in kinetic energy and, consequently, more work will be done on it.
This relationship arises from the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy. Understanding this concept helps in analyzing the energy transfer and mechanical behavior of objects in systems involving springs and masses.
To know more about kinetic energy ,visit:
https://brainly.com/question/8101588
#SPJ11
A 6.0-m uniform board is supported by two sawhorses 4.0 m aprat as shown. A 32 kg child walks on the board to 1.4 m beyond the right support when the board starts to tip, that is, the board is off the left support. Find the mass of the board. (Hint: the weight of the board can be considered to be applied at its center of gravity.)
When 6.0-m uniform board is supported by two sawhorses 4.0 m apart and a 32 kg child walks on the board to 1.4 m beyond the right support when the board starts to tip, that is, the board is off the left support then the mass of the board is 1352 kg.
Given data :
Length of board = L = 6 m
Distance between sawhorses = d = 4 m
Mass of child = m = 32 kg
The child walks to a distance of x = 1.4 m beyond the right support.
The length of the left over part of the board = L - x = 6 - 1.4 = 4.6 m
As the board is uniform, the center of gravity is at the center of the board.The weight of the board can be considered to be applied at its center of gravity. The board will remain in equilibrium if the torques about the two supports are equal.
Thus, we can apply the principle of moments.
ΣT = 0
Clockwise torques = anticlockwise torques
(F1)(d) = (F2)(L - d)
F1 = (F2)(L - d)/d
Here, F1 + F2 = mg [As the board is in equilibrium]
⇒ F2 = mg - F1
Putting the value of F2 in the equation F1 = (F2)(L - d)/d
We get, F1 = (mg - F1)(L - d)/d
⇒ F1 = (mgL - mF1d - F1L + F1d)/d
⇒ F1(1 + (L - d)/d) = mg
⇒ F1 = mg/(1 + (L - d)/d)
Putting the given values, we get :
F1 = (32)(9.8)/(1 + (6 - 4)/4)
F1 = 588/1.5
F1 = 392 N
Let the mass of the board be M.
The weight of the board W = Mg
Let x be the distance of the center of gravity of the board from the left support.
We have,⟶ Mgx = W(L/2) + F1d
Mgx = Mg(L/2) + F1d
⇒ Mgx - Mg(L/2) = F1d
⇒ M(L/2 - x) = F1d⇒ M = (F1d)/(L/2 - x)
Substituting the values, we get :
M = (392)(4)/(6 - 1.4)≈ 1352 kg
Therefore, the mass of the board is 1352 kg.
To learn more about mass :
https://brainly.com/question/86444
#SPJ11
What is Lorentz number? The thermal and electrical
conductivities of Cu at 200C are 390 Wm-1K-1 and 5.87 x107-1m-1
respectively. Calculate Lorentz number.
The value of the Lorentz Number is L = (390 W/(m·K)) / (5.87 x 10^7 Ω^(-1)·m^(-1) * 473.15 K).
The Lorentz number, denoted by L, is a fundamental constant in physics that relates the thermal and electrical conductivities of a material. It is given by the expression:
L = (π^2 / 3) * (kB^2 / e^2),
where π is pi (approximately 3.14159), kB is the Boltzmann constant (approximately 1.380649 x 10^-23 J/K), and e is the elementary charge (approximately 1.602176634 x 10^-19 C).
To calculate the Lorentz number, we need to know the thermal conductivity (κ) and the electrical conductivity (σ) of the material. In this case, we are given the thermal conductivity (κ) of copper (Cu) at 200°C, which is 390 W/(m·K), and the electrical conductivity (σ) of copper (Cu) at 200°C, which is 5.87 x 10^7 Ω^(-1)·m^(-1).
The Lorentz number can be calculated using the formula:
L = κ / (σ * T),
where T is the temperature in Kelvin. We need to convert 200°C to Kelvin by adding 273.15.
T = 200 + 273.15 = 473.15 K
Substituting the given values into the formula:
[tex]L = (390 W/(m·K)) / (5.87 x 10^7 Ω^(-1)·m^(-1) * 473.15 K).[/tex]
Calculating this expression will give us the value of the Lorentz number.
Learn more about Lorentz number
https://brainly.com/question/30243962
#SPJ11
Problem 4. (5 points) The side (s) of a cube was measured as 2.6 + 0.01 cm. If the volume of the cube is given by V = s3 and the nominal value for the volume is calculated as 17.58 cm", what is the uncertainty in the volume of the cube expressed in cm3?
the uncertainty in the volume of the cube expressed in cm³ is 0.20219 cm³.
Given that the length of the side of a cube, s = 2.6 + 0.01 cm
Nominal value for the volume of the cube = V = s³ = (2.6 + 0.01)³ cm³= (2.61)³ cm³ = 17.579481 cm³
The absolute uncertainty in the measurement of the side of a cube is given as
Δs = ±0.01 cm
Using the formula for calculating the absolute uncertainty in a cube,
ΔV/V = 3(Δs/s)ΔV/V = 3 × (0.01/2.6)ΔV/V
= 0.03/2.6ΔV/V = 0.01154
The uncertainty in the volume of the cube expressed in cm³ is 0.01154 × 17.58 = 0.20219 cm³ (rounded off to four significant figures)
Therefore, the uncertainty in the volume of the cube expressed in cm³ is 0.20219 cm³.
learn more about uncertainty here
https://brainly.com/question/30847661
#SPJ11
A particle moves through an xyz coordinate system while a force acts on it. When the particle has the position vector 7 = (2.00 mi - (3.00 m)ſ + (2.00 m), the force is F = F/+ (7.00 N)5 - (6.70 N) and the corresponding torque about the origin is(6.10 Nm)i + (3.00 Nm)j + (-1.60 Nm). Determine Fx N
The direction of torque vector is perpendicular to the plane containing r and force, in the direction given by the right hand rule. The value of Fx is 0.522 N.
Position vector, r = 7 = (2.00 mi - (3.00 m)ſ + (2.00 m))Force vector, F = (7.00 N)5 - (6.70 N)Torque vector, τ = (6.10 Nm)i + (3.00 Nm)j + (-1.60 Nm)The equation for torque is given as : τ = r × FWhere, × represents cross product.The cross product of two vectors is a vector that is perpendicular to both of the original vectors and its magnitude is given as the product of the magnitudes of the original vectors times the sine of the angle between the two vectors.Finding the torque:τ = r × F= | r | | F | sinθ n, where n is a unit vector perpendicular to both r and F.θ is the angle between r and F.| r | = √(2² + 3² + 2²) = √17| F | = √(7² + 6.70²) = 9.53 sinθ = τ / (| r | | F |)n = [(2.00 mi - (3.00 m)ſ + (2.00 m)) × (7.00 N)5 - (6.70 N)] / (| r | | F | sinθ)
By using the right hand rule, we can determine the direction of the torque vector. The direction of torque vector is perpendicular to the plane containing r and F, in the direction given by the right hand rule. Finding Fx:We need to find the force component along the x-axis, i.e., FxTo solve for Fx, we will use the equation:Fx = F cosθFx = F cosθ= F (r × n) / (| r | | n |)= F (r × n) / | r |Finding cosθ:cosθ = r . F / (| r | | F |)= [(2.00 mi - (3.00 m)ſ + (2.00 m)) . (7.00 N) + 5 . (-6.70 N)] / (| r | | F |)= (- 2.10 N) / (| r | | F |)= - 2.10 / (9.53 * √17)Fx = (7.00 N) * [ (2.00 mi - (3.00 m)ſ + (2.00 m)) × [( - 2.10 / (9.53 * √17)) n ] / √17= 0.522 NTherefore, the value of Fx is 0.522 N.
Learn more about force:
https://brainly.com/question/30507236
#SPJ11
The tungsten filament of a light bulb has a resistance of 8.00 22 when no current flows, and its temperature is 20°C. Esti- mate the filament's temperature when a 1.00-A current flows after a 120-V potential difference is placed across the filament
The temperature of the tungsten filament is approximately 296.15 K when a 1.00-A current flows through it after a 120-V potential difference is placed across the filament.
Resistance of filament when no current flows,R= 8.00Ω
Temperature, T = 20°C = 293 K
Current flowing in the circuit, I = 1.00 A
Potential difference across the filament, V = 120 V
We can calculate the resistance of the tungsten filament when a current flows through it by using Ohm's law. Ohm's law states that the potential difference across the circuit is directly proportional to the current flowing through it and inversely proportional to the resistance of the circuit. Mathematically, Ohm's law is expressed as:
V = IR Where,
V = Potential difference
I = Current
R = Resistance
The resistance of the filament when the current is flowing can be given as:
R' = V / IR' = 120 / 1.00R' = 120 Ω
We know that the resistance of the filament depends on the temperature. The resistance of the filament increases with an increase in temperature. This is because the increase in temperature causes the electrons to vibrate more rapidly and collide more frequently with the atoms and other electrons in the metal. This increases the resistance of the filament.The temperature coefficient of resistance (α) can be used to relate the change in resistance of a material to the change in temperature. The temperature coefficient of resistance is defined as the fractional change in resistance per degree Celsius or per Kelvin. It is given by:
α = (ΔR / RΔT) Where,
ΔR = Change in resistance
ΔT = Change in temperature
T = Temperature
R = Resistance
The temperature coefficient of tungsten is approximately 4.5 x 10^-3 / K.
Therefore, the resistance of the tungsten filament can be expressed as:
R = R₀ (1 + αΔT)Where,
R₀ = Resistance at 20°C
ΔT = Change in temperature
Substituting the given values, we can write:
120 = I (8 + αΔT)
120 = 8I + αIΔT
αΔT = 120 - 8IαΔT = 120 - 8 (1.00)αΔT = 112Kα = 4.5 x 10^-3 / KΔT = α⁻¹ ΔR / R₀ΔT = (4.5 x 10^-3)^-1 x (112 / 8)
ΔT = 3.15K
Filament temperature:
T' = T + ΔTT' = 293 + 3.15T' = 296.15 K
Therefore, the temperature of the tungsten filament is approximately 296.15 K when a 1.00-A current flows through it after a 120-V potential difference is placed across the filament.
Learn more about tungsten filament https://brainly.com/question/30945041
#SPJ11
Given the following simple circuit having 10.06 volts and a current of 2.52 amps, calculate the resistance in units of ohms. 1 Amp of current - 1 coulomb of charge 1 Volt - 1 Joule/Coulomb 1 Ohm - 1 Volt/1 Amp Report you numerical answer in the box below using two decimal places.
The resistance of the circuit is approximately 3.98 ohms. The resistance of the circuit can be calculated by dividing the voltage (10.06 volts) by the current (2.52 amps).
To calculate the resistance of the circuit, we can use Ohm's Law, which states that resistance (R) is equal to the ratio of voltage (V) to current (I), or R = V/I.
The formula for calculating resistance is R = V/I, where R is the resistance, V is the voltage, and I is the current. In this case, the voltage is given as 10.06 volts and the current is given as 2.52 amps.
Substituting the given values into the formula, we have R = 10.06 volts / 2.52 amps.
Performing the division, we get R ≈ 3.98 ohms.
To learn more about ohms law-
brainly.com/question/23579474
#SPJ11
3. [-/5 Points] DETAILS SERCP11 15.3.P.026. A helium nucleus of mass m 6.64 x 10-27 kg and charge q= 3.20 x 10-19 C is in a constant electric field of magnitude E4.00 x 10-7 N/C pointing in the positive x-direction. Neglecting other forces, calculate the nucleus' acceleration and its displacement after 1.70 s if it starts from rest. (Indicate the direction with the sign of your answer.) HINT (a) the nucleus acceleration (in m/s) 1.93x1011 x Your answer cannot be understood or graded. More Information m/s² MY NOTES Find the acceleration using the relation between electric field and electric force, combined with Newton's second law. Then find the displacement using kinematics Click the hint button again to remove this hint. (b) its displacement (in m) 1.64x10 11 x Your answer cannot be understood or graded. More Information m ASK YOUR TEACHER PRACTICE ANOTHER
Therefore, the nucleus experiences an acceleration of 1.93 × 10¹¹ m/s² in the positive x-direction, and its displacement after 1.70 s is 1.64 × 10¹¹m in the positive x-direction.
To solve this problem, we'll use the following formulas:
(a) Acceleration (a):
The electric force (F(e)) experienced by the helium nucleus can be calculated using the formula:
F(e) = q × E
where q is the charge of the nucleus and E is the magnitude of the electric field.
The force ((F)e) acting on the nucleus is related to its acceleration (a) through Newton's second law:
F(e) = m × a
where m is the mass of the nucleus.
Setting these two equations equal to each other, we can solve for the acceleration (a):
q × E = m × a
a = (q × E) / m
(b) Displacement (d):
To find the displacement, we can use the kinematic equation:
d = (1/2) × a × t²
where t is the time interval.
Given:
m = 6.64 × 10²⁷ kg
q = 3.20 × 10¹⁹ C
E = 4.00 ×10⁻⁷ N/C
t = 1.70 s
(a) Acceleration (a):
a = (q × E) / m
= (3.20 × 10¹⁹ C ×4.00 × 10⁻⁷ N/C) / (6.64 × 10⁻²⁷ kg)
= 1.93 ×10¹¹ m/s² (in the positive x-direction)
(b) Displacement (d):
d = (1/2) × a × t²
= (1/2) × (1.93 × 10¹¹ m/s²) ×(1.70 s)²
= 1.64 × 10¹¹ m (in the positive x-direction)
Therefore, the nucleus experiences an acceleration of 1.93 × 10¹¹ m/s² in the positive x-direction, and its displacement after 1.70 s is 1.64 × 10¹¹m in the positive x-direction.
To know more about helium nucleus:
https://brainly.com/question/13153367
#SPJ4
Consider a volume current density () in a conducting system where the charge density p() does not change with time. Determine V.J(7). Explain your answer.
The volume current density for a conducting system where the charge density p() does not change with time is given by J(t) = J0exp(i * 7t), where J0 is the maximum current density and t is the time.
However, we want to determine V.J(7), which means we need to find the value of the current density J at a particular point V in the system. Therefore, we need more information about the system to be able to calculate J(7) at that point V.
Learn more about charge density: https://brainly.com/question/14306160
#SPJ11
A)At what temperature will an aluminum ring at 30 C,with 11 cm diameter fit over a copper rod with a diameter of 0.1101m? ( assume both are in thermal equilibrium while the temperature is being changed.) (α= 24 x 10-6C-1 for aluminum , α= 17 x 10-6 C-1 for copper)
B)If Joe Scientist has created his own temperature scale where water freezes at 57 and boils at 296, create a transformation equation that will allow you to convert celcius into his temperatures.
C C) At what temperature will the root mean square speed of carbon dioxide(CO2) be 450 m/s?( z=8 and n=8 for Oxygen atoms, z =6, n=6 for carbon)
A) The temperature at which the aluminum ring at 30°C will fit over the copper rod with a diameter of 0.1101m can be calculated to be approximately 62.04°C.
To determine the temperature at which the aluminum ring will fit over the copper rod, we need to find the temperature at which both objects have the same diameter.
The change in diameter (∆d) of a material due to a change in temperature (∆T) can be calculated using the formula:
∆d = α * d * ∆T
where α is the coefficient of linear expansion and d is the initial diameter.
For aluminum:
∆d_aluminum = α_aluminum * d_aluminum * ∆T
For copper:
∆d_copper = α_copper * d_copper * ∆T
Since both materials are in thermal equilibrium, the change in diameter for both should be equal:
∆d_aluminum = ∆d_copper
Substituting the values and solving for ∆T:
α_aluminum * d_aluminum * ∆T = α_copper * d_copper * ∆T
Simplifying the equation:
α_aluminum * d_aluminum = α_copper * d_copper
Substituting the given values:
(24 x 10^-6 C^-1) * (0.11m) = (17 x 10^-6 C^-1) * (∆T) * (0.1101m)
Solving for ∆T:
∆T = [(24 x 10^-6 C^-1) * (0.11m)] / [(17 x 10^-6 C^-1) * (0.1101m)]
∆T ≈ 0.05889°C
To find the final temperature, we add the change in temperature to the initial temperature:
Final temperature = 30°C + 0.05889°C ≈ 62.04°C
The temperature at which the aluminum ring at 30°C will fit over the copper rod with a diameter of 0.1101m is approximately 62.04°C.
B) The transformation equation to convert Celsius (C) into Joe Scientist's temperature scale (J) is: J = (C - 32) * (296 - 57) / (100 - 0) + 57.
Joe Scientist's temperature scale has a freezing point of 57 and a boiling point of 296, while the Celsius scale has a freezing point of 0 and a boiling point of 100. We can use these two data points to create a linear transformation equation to convert Celsius into Joe Scientist's temperature scale.
The equation is derived using the formula for linear interpolation:
J = (C - C1) * (J2 - J1) / (C2 - C1) + J1
where C1 and C2 are the freezing and boiling points of Celsius, and J1 and J2 are the freezing and boiling points of Joe Scientist's temperature scale.
Substituting the given values:
C1 = 0, C2 = 100, J1 = 57, J2 = 296
The transformation equation becomes:
J = (C - 0) * (296 - 57) / (100 - 0) + 57
Simplifying the equation:
J = C * (239 / 100) + 57
J = (C * 2.39) + 57
The transformation equation to convert Celsius (C) into Joe Scientist's temperature scale (J) is J = (C * 2.
39) + 57.
C) The temperature at which the root mean square speed of carbon dioxide (CO2) is 450 m/s can be calculated to be approximately 2735 K.
The root mean square speed (vrms) of a gas is given by the equation:
vrms = sqrt((3 * k * T) / m)
where k is the Boltzmann constant, T is the temperature in Kelvin, and m is the molar mass of the gas.
For carbon dioxide (CO2), the molar mass (m) is the sum of the molar masses of carbon (C) and oxygen (O):
m = (z * m_C) + (n * m_O)
Substituting the given values:
z = 8 (number of oxygen atoms)
n = 6 (number of carbon atoms)
m_C = 12.01 g/mol (molar mass of carbon)
m_O = 16.00 g/mol (molar mass of oxygen)
m = (8 * 16.00 g/mol) + (6 * 12.01 g/mol)
m ≈ 128.08 g/mol
To find the temperature (T), we rearrange the equation for vrms:
T = (vrms^2 * m) / (3 * k)
Substituting the given value:
vrms = 450 m/s
Using the Boltzmann constant k = 1.38 x 10^-23 J/K, and converting the molar mass from grams to kilograms (m = 0.12808 kg/mol), we can calculate:
T = (450^2 * 0.12808 kg/mol) / (3 * 1.38 x 10^-23 J/K)
T ≈ 2735 K
The temperature at which the root mean square speed of carbon dioxide (CO2) is 450 m/s is approximately 2735 K.
To know more about temperature visit:
https://brainly.com/question/27944554
#SPJ11
The main water line enters a house on the first floor. The line has a gauge pressure of 285 x 10% Pa(a) A faucet on the second floor, 4.10 m above the first floor, is turned off. What is the gauge pressure at this faucet? (b) How high could a faucet be before no water would flow from it even if the faucet were open? (a) Number 1 Units (b) Number Units A water tower is a familiar sight in many towns. The purpose of such a tower is to provide storage capacity and to provide sufficient pressure in the pipes that deliver the water to customers. The drawing shows a spherical reservoir that contains 3.09 x 105 kg of water when full. The reservoir is vented to the atmosphere at the top. For a full reservoir, find the gauge pressure that the water has at the faucet in (a) house A and (b) house B. Ignore the diameter of the delivery pipes. Vent 150 m Facet 12.30 m Faucet (a) Number i Units (b) Number Units
The gauge pressure at the faucet is [tex]325\times10^{3} Pa[/tex] and the maximum height is 29.169 m.
(a) To find the gauge pressure at the faucet on the second floor, we can use the equation for pressure due to the height difference:
Pressure = gauge pressure + (density of water) x (acceleration due to gravity) x (height difference).
Given the gauge pressure at the main water line and the height difference between the first and second floors, we can calculate the gauge pressure at the faucet on the second floor. So,
Pressure =[tex]2.85\times 10^{5}+(997)\times(9.8)\times(4.10) =325\times10^{3} Pa.[/tex]
Thus, the gauge pressure at the faucet on the second floor is [tex]325\times10^{3} Pa.[/tex]
(b) The maximum height at which water can be delivered from a faucet depends on the pressure needed to push the water up against the force of gravity. This pressure is related to the maximum height by the equation:
Pressure = (density of water) * (acceleration due to gravity) * (height).
By rearranging the equation, we can solve for the maximum height.
Maximum height = [tex]\frac{pressure}{density of water \times acceleration of gravity}\\=\frac{2.85 \times10^{5}}{997\times 9.8} \\=29.169 m[/tex]
Therefore, the gauge pressure at the faucet is [tex]325\times10^{3} Pa[/tex] and the maximum height is 29.169 m.
Learn more about pressure here: brainly.com/question/28012687
#SPJ11
CORRECT QUESTION
The main water line enters a house on the first floor. The line has a gauge pressure of [tex]2.85\times10^{5}[/tex] Pa. (a) A faucet on the second floor, 4.10 m above the first floor, is turned off. What is the gauge pressure at this faucet? (b) How high could a faucet be before no water would flow from it even if the faucet were open?
Set the parameters as follows: vo = 0, k = 0.4000, s = 0.5000, g = 9.810 m/s2, m = 5.000 kg. Predict: In order to keep the block at rest on the incline plane, the angle of the incline plane can’t exceed what value? Draw a free body diagram of the block and show your calculation.
To predict the maximum angle of the incline plane (θ) at which the block can be kept at rest, we need to consider the forces acting on the block
. The key is to determine the critical angle at which the force of static friction equals the maximum force it can exert before the block starts sliding.
The free body diagram of the block on the incline plane will show the following forces: the gravitational force (mg) acting vertically downward, the normal force (N) perpendicular to the incline, and the force of static friction (fs) acting parallel to the incline in the opposite direction of motion.
For the block to remain at rest, the force of static friction must be equal to the maximum force it can exert, given by μsN. In this case, the coefficient of static friction (μs) is 0.5000.
The force of static friction is given by fs = μsN. The normal force (N) is equal to the component of the gravitational force acting perpendicular to the incline, which is N = mgcos(θ).
Setting fs equal to μsN, we have fs = μsmgcos(θ).
Since the block is at rest, the net force acting along the incline must be zero. The net force is given by the component of the gravitational force acting parallel to the incline, which is mgsin(θ), minus the force of static friction, which is fs.
Therefore, mgsin(θ) - fs = 0. Substituting the expressions for fs and N, we get mgsin(θ) - μsmgcos(θ) = 0.
Simplifying the equation, we have sin(θ) - μscos(θ) = 0.
Substituting the values μs = 0.5000 and μk = 0.4000 into the equation, we can solve for the angle θ. The maximum angle θ at which the block can be kept at rest is the angle that satisfies the equation sin(θ) - μscos(θ) = 0. By solving this equation, we can find the numerical value of the maximum angle.
Learn more about inclination here: brainly.com/question/29360090
#SPJ11