9.37 the force per unit length/that is exerted by the wind on the 24 ft tall sail as a function of it height z is given by

Answers

Answer 1

The force between two parallel currents I1 and I2 that are spaced apart by r is measured as the ratio F/l.

If the currents are flowing in the same direction, the force is attracting; if not, it is repulsive. The pinch effect in electric arcs and other plasmas is caused by this force. The basic concept of the ampère derives from this force between two current-carrying wires: The strain on each wire is 2 x 10- 7 N/m if two long parallel wires spaced 1 m apart carry a current of 1 A each. The International System of Units' (Symbol: N) unit of force is the newton (SI).

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4


Related Questions

technician a says that the primary difference between deep-cycle batteries and sli is the thickness of the plates. technician b says that deeply discharging sli batteries dramatically shortens their service life. who is correct?

Answers

Both technician a and technician b are correct that SLI battery' service life is significantly shortened by deeply discharging them, and that the thickness of the plates is the main difference between both batteries.

A lead-acid storage and rechargeable battery known as an SLI battery is primarily utilized in internal combustion engines for vehicles and other internal combustion powered devices. Simply put, SLI stands for starting, lighting, and ignition. It is intended to start, run, and maintain power supply. SLI batteries use thinner lead dioxide-filled plates instead of the thicker ones used in deep cycle batteries. As opposed to the higher current produced by an SLI battery, deep cycle batteries deliver a steady, lower current. Deep cycle batteries are made for repeated discharge and recharge in applications like RVs, golf carts, floor scrubbers, and electric vehicles. Generally speaking, deep cycle batteries shouldn't be discharged below 80% depth of discharge.

Learn more about SLI battery here:

https://brainly.com/question/28146138

#SPJ4

______________________ refers to a programming model used within Hadoop that performs the two major steps for which it is named: the map step and the reduce step.

Answers

Map Reduce refers to a programming model used within Hadoop that performs the two major steps for which it is named: the map step and the reduce step.

What is meant by MapReduce?A parallel, distributed algorithm called MapReduce is a programming model with an accompanying implementation for handling and producing large amounts of data on a cluster. A map method, which performs filtering and sorting, and a reduce method, which does a summary operation, make up a map reduction programme.MapReduce was created primarily to address the need for an easy method of managing computationally demanding tasks in a parallelized, scalable, and fault-tolerant manner across large clusters of machines.MapReduce is incredibly effective and useful for a wide range of issues, however it is not the solution to all issues. There will be a significant performance hit if the Reduce step generates too much data because the index created in the Map step is only one dimension.

To learn more about MapReduce refer :

https://brainly.com/question/14571523

#SPJ4

technician a says that liner protrusion can be measured with a flat bar and feeler blades. technician b says a dial indicator mounted on a sled should be used. who is correct?

Answers

You must use cylinder liner shims or a bigger flange height cylinder liner to increase the protrusion height if the new cylinder liner falls short of the engine manufacturer's specifications.

One of the most frequent reasons for low oil pressure is when the oil level falls below the minimum dipstick line. Even if you just had an oil change, this could occur at any time. Engines burn oil more fast with time. This is brought on by the deterioration of piston rings, leaking seals, etc. Engine temperature, which ultimately determines the temperature that the oil reaches, is the most frequent source of excessive oil pressure. Oil pressure increases might also be a result of broken engine parts.

Learn more about engine here-

https://brainly.com/question/27162243

#SPJ4

6.in a typical structural steel floor or roofing framing, there are three types of elements, called primary, secondary and tertiary elements. explain what these are and what materials they consist of.

Answers

Steel is the emaerial used because it is stated that the floor is made of steel. Any material, such as wood, steel, or composite, may be used for roof framing.

Primary elements are the main member in floor system which transfer the load coming on to the element from secondary beam elemnts.The main beams will be joined to the building's columns. The two most common shapes are H and W sections. Secondary elements, which span between principal beams, often accept the slab's weight before passing it on to the primary elemnts. The primary components are joined to the secondary beams for load transfer. Secondary elements are seldom ever employed. If employed, they function as a load transfer system from the slab to the secondary element or as a means of strengthening the floor system to lessen deflection. The top chord and bottom tie members are the main components of roof framing. The weight is transferred from the purlins to the columns or wall via these elements. often have a double-angle or channel section. Tie and the chord member between the top are secondary components.Ther are subjected to compression and tension and transfer forces to the primary elements.

Learn more about roof framing here:

https://brainly.com/question/14799449

#SPJ4

Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure). The length of pipe immersed in the lake is negligible compared to the length from the lake surface to the discharge point. The flow rate is to be 95 gal/min, and the flow channel is a standard 1-inch. Schedule 40 steel pipe (ID= 1.049 inch). A pump capable of delivering 8 hp(-Ws) is available. The friction loss F (ft lb/lbm) equals 0.041L, where L(ft) is the length of the pipe. (a) Calculate the maximum elevation, z, of the ranger station above the lake if the pipe rises at an angle of 30° (b) Suppose the pipe inlet is immersed to a significantly greater depth below the surface of the lake, but it discharges at the elevation calculated in Part (a). The pressure at the pipe inlet would be greater than it was at the original immersion depth, which means that ΔP from inlet to outlet would be greater, which in turn suggests that a smaller pump would be sufficient to move the water to the same elevation. In fact, however, a larger pump would be needed. Explain (i) why the pressure at the inlet would be greater than in Part (a), and (ii) why a larger pump would be needed. 30°

Answers

a) If the pipe rises at a 30° angle, the ranger station's maximum elevation, z, above the lake is 290 feet.

b) As we descend, the lake's pressure always rises. In comparison to point 2, point 3 has higher pressure. Because the rise in pressure is offset by the fall in datum, pump power remains constant for the same height, z=290 feet.

What is pressure?

In the physical sciences, pressure is referred to as the stress at a point within a confined fluid or the perpendicular force per unit area. The force divided by the area over which it is exerted, or half a pound per square inch, determines the pressure that a 42-pound box with an area of 84 square inches at the bottom places on a floor.

Atmospheric pressure, which is roughly 15 pounds per square inch at sea level, is the amount of weight that the atmosphere exerts on each unit area of the Earth's surface. In SI units, pressure is expressed in pascals, where one pascal is equal to one newton per square meter. The atmosphere has a pressure of almost 100,000 pascals.

Learn more about pressure

https://brainly.com/question/945436

#SPJ4

What is the period of the clock in the code snippet?(Please provide the answer in 'ns') 'timescale 5 ns / 1 ps reg clk; initial clk = 0; always #10 clk = clk; A

Answers

It is to be noted that from the code snippet, since the clock changes every 10-time units, has a half cycle of 10 seconds, therefore the period is 20 units.  

What is the explanation of the above result?

A clock with a half cycle of 10 seconds and a period of 20-time units would have a half cycle of 10 seconds and a period of 20-time units. A clock that changes every 10 seconds, for example, would have a half cycle of 10 seconds.

As a result, the accuracy is 1ns and the time unit is 10ns. To retrieve the actual simulation time, multiply the time unit by the delay set with #, which is then rounded down based on accuracy. The first delay statement returns 10ns, whereas the second delay statement returns 14.9, which is rounded to 15ns.

Note that a snippet is a tiny area of reusable source code, machine code, or text in programming. These are often explicitly specified operational units that are included in bigger programming modules. Some text editors, computer source code editors, IDEs, and related tools provide snippet management.

Learn more about code snippets:
https://brainly.com/question/15003151
#SPJ1

show that complex fourier series coefficients can be expressed as for each of the followig two periodic signals write the fourier series

Answers

Apparently, some people claim that every signal may be described as a Fourier series, notably in electrical engineering and musical signal processing.

This prompted me to consider the mathematical justification for such an argument.

However, even after reading through various materials on the Fourier series (which I have little background in but understand the notion of), I was unable to locate a mathematical justification for the claim that every function can be represented by a Fourier series. The need for the function to be periodic was alluded to.

Most functions cannot be expressed as Fourier series, as may be seen by a simple counting argument. A countable family of Fourier coefficients serves as the basis for a Fourier series, and as a result, the set of such series has cardinality c0, as opposed to the set of real valued functions defined on some interval, which has cardinality cc.

To know more about functions click here:

https://brainly.com/question/9171028

#SPJ4

a magnet made from a steel paperclip is most likely a(n) a. permanent magnet. b. temporary magnet. c. electron. d. lodestone. please select the best answer from the choices provided a b c d

Answers

Option A is correct. Only a strong magnetic field has the power to magnetize it. But after being magnetized, steel has the capacity to hold onto its magnetic properties.

Steel is suitable for use in permanent magnets thanks to this property. Since paperclips are not magnetic by nature, they cannot be chained together on their own. The paperclips can, however, be momentarily magnetic by employing a magnet. A paper clip's steel can be easily magnetic, but it quickly loses its magnetism. Steel wire is typically used to make paper clips. Steel is an iron and carbon alloy. Magnets are drawn to iron because it is a ferromagnetic material.

Learn more about steel here-

https://brainly.com/question/22573226

#SPJ4

Answer: A

Explanation:

you assigned the assistant network administrator to replace a defective patch cable that connected port 1 on your patch panel to one of your network switches. you noticed that it took him an unusually long time to complete this task. once done, users almost immediately began to report that the network had gone down.

Answers

Set up the Windows 2000 workstations' VLAN membership so that they are on their own VLAN.

As the gateway to a wide area network (WAN) or the Internet, the core switch is also regarded as a backbone component that is essential to the smooth operation of a network. We can use it to connect to servers, our Internet service provider (ISP), via a router, and to aggregate all switches. When a client submits a request, a load balancer receives it and distributes it to various servers. Distributing client requests evenly among several servers is one objective of load balancing, which also aims to boost performance.

Learn more about operation here-

https://brainly.com/question/27960749

#SPJ4

___________ is the party that facilitates the movement of cargo to the international destination on behalf of shippers and processes the documentation or performance activities related to those shipments.
Freight forwarder

Answers

Freight forwarder is the party that facilitates the movement of cargo to the international destination on behalf of shippers and processes the documentation or performance activities related to those shipments.

A company that specializes in organizing goods on behalf of shippers is known as a freight forwarder.

Freight forwarders typically offer a range of supply chain services, such as: Ocean or air freight transport. from the point of origin to the point of destination by land. A freight forwarder plans shipments for businesses or individuals. The break-bulk and distribution of cargoes are handled by freight forwarders, who also assemble and combine goods. Freight forwarders, as opposed to brokers, take charge of the transportation and sometimes even move the freight themselves. The main distinction is that a freight forwarder will assume responsibility for transportation both to and from ports.

Learn more about Cargoes here-

https://brainly.com/question/14603564

#SPJ4

Consider a process carried out on 1.00 mol of a monatomic ideal gas by the following two different pathways. The first pathwayis A (3.00 atm, 20.0 L) to C (1.00 atm, 20.0 L) to D (1.00 atm, 50.0 L); and the second pathway is A (3.00 atm, 20.0 L) to B (3.00atm, 50.0 L) to D (1.00 atm, 50.0 L). In each case, the gas is taken from state A to state D.33. Calculate wAB.a. 0b. 90 L•atmc. –90 L•atmd. –30 L•atme. 30 L•atm34. Calculate wAC.a. 0b. 30 L•atmc. –30 L•atmd. 90 L•atme. –90 L•atm35. Calculate q AB.a. 135 L•atmb. –135 L•atmc. 225 L•atmd. –225 L•atme. none of these36. Calculate q AC.a. 60 L•atmb. 100 L•atmc. –60 L•atmd. –100 L•atme. none of these

Answers

The calculated answer is 90 L atm, a pure gas made up only of atoms. The noble gases argon, krypton, and xenon are some examples.

Consider a monatomic perfect gas with m-mean particles that don't interact and a resting mass center. An ion with only one atom is referred to as a monatomic ion or simple ion. A polyatomic ion is one that has more than one atom, even if they are all from the same element.

From the information provided:

The first route:

A (1 atm, 20 L), C (3 atm), and D (1 atm, 50 L)

The second route:

A (3 atm, 50 L), B (3 atm, 20 L), and D ( 1 atm, 50 L)

Because one mole equals one mole,

to locate wAB;

The conversion is depicted as A B occurring under constant pressure.

Pressure x Volume Change = wAB

V2 - V1 = wAB

atm = wAB ( 50 L - 20 L)

atm = wAB ( 30 L)

wAB=90 L.atm

Learn more about monoatomic here-

https://brainly.com/question/19865411

#SPJ4

How many floor joists are required for a building 28 feet wide by 32 feet long if the joists are spaced 16 o.c. and there is a girder in the​ center?

Answers

22  I-beams, 32 feet long and 5 end-plate boards 12 feet long.

How can I figure out how many floor joists ?

The standard distance between deck joists is either 12 inches or 16 inches on center. (On-center refers to the distance between the centers of two joists rather than the distance between their edges.)

Subtract the width of your floor joist from the length of your floor: 32 -28

the total of the floor joists' on-center spacing divided by that difference  16"/4 = 4

To this value, add 1, then round the result to the next whole number:

22  I-beams, 32 feet long and 5 end-plate boards (e.g., 2x12s) 12 feet long.

To learn more about  floor joist refer to:

https://brainly.com/question/9477456

#SPJ1

technician a says that diesel engine oil operates at higher temperatures than spark-ignition engine oil because it cools pistons. technician b says that diesel engine oil operates at close to coolant temperature. who is correct?

Answers

Technician a is correct because he says that due to the cooling effect on pistons, diesel engine oil operates at higher temperatures than spark-ignition engine oil.

The diesel engine modeled after Rudolf Diesel is an example of a compression-ignition internal combustion engine, which ignites fuel by heating the air in the cylinder as a result of mechanical compression. Theoretically, diesel engines operate by compressing air to a high pressure and temperature, then injecting a small amount of fuel into the heated compressed air in cylinder. Due to the high temperature, the small amount of fuel that was injected and vigorously atomized evaporates.Diesel engines come in two different classes: two-stroke and four-stroke. Some bigger diesel engines operate on the two-stroke cycle, while most diesel engines utilize the four-stroke cycle. They generally have four or six in-line, direct-injection cylinders.

Learn more about diesel engine here:

https://brainly.com/question/1381153

#SPJ4

In the diagram shown, which process is surface runoff?

Answers

In the diagram shown, the process that is surface runoff is the surface labelled D.

What is surface runoff?

Surface runoff is the flow of water happening on the ground surface when much rainwater, storm water, meltwater, or other sources, will no more sufficiently fast infiltrate in the soil. This is possible when the soil is exhausted by water to its full capacity, and the rain arrives more quickly than the soil can absorb it.

Therefore, the correct answer is as given above. That is, the surface tagged D depict the flow of water on the ground surface which is otherwise known as surface runoff.

learn more about surface runoff: https://brainly.com/question/29478956

#SPJ4

the flip-flop input equations for a bcd counter using t flip-flops are given in section 6.4. obtain the input equations for a bcd counter that uses (a) jk flip-flops and (b)* d flipflops. compare the three designs to determine which one is the most efficient.

Answers

BCD counters count using BCD numbers from 0000 to 1001 before looping back to 0000 and repeating the process.

Since a decimal digit is represented by a binary code with at least four bits and a MOD-10 count, such a counter must have at least four flip-flops to represent each digit. JK flip flops and a NAND gate are used to build the BCD or decade counter circuit. Since the BCD system is a 4-bit binary counter, its architecture is quite straightforward and only calls for four JK flip flops. The decade counter's design is depicted below. A counter like the one in the circuit above that has three flip-flops will then count from 0 to 7 or 2n-1.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

in a p -n junction, the n-doping nd is doubled. how do the following change if everything else remains unchanged? indicate only increase or decrease. (a) junction capacitance (b) built-in potential (c) breakdown voltage (d) ohmic losses

Answers

In a p-n junction, option c is accurate because the  is double. the values below change if everything else stays the same and they only indicate a rise or fall in breakdown voltage.

Breakdown voltage It is the voltage at which current in a forward biased PN junction begins to flow or increases. When reverse voltage is present, junctions break down and reverse current increases quickly. The depletion layer's width narrows. The depletion layer becomes wider. A diode's breakdown voltage specifies the highest reverse voltage that can be used without exponentially increasing the leakage current in the diode. A diode won't necessarily be destroyed if its breakdown voltage is exceeded, but it will be if its current capacity is. To create an ionization path through the dielectric, the open gap voltage must increase before current can flow.

Learn more about breakdown voltage here:

https://brainly.com/question/29513692

#SPJ4

Mayim is very good at math, especially probabilities and statistics. Which job in the supply chain is a good fit for her skills?

Answers

Answer:

Inventory Planner

Explanation:

An inventory planner is a specialist that is in charge of developing efficient inventory plans and strategies to enhance an organization's profitability. Inventory planners must create paperwork outlining the quantity specifications of the organization's goods or equipment.

to determine the maximum likelihood estimation, computerized adaptive testing (cat) software weights all of the following except .

Answers

To determine the maximum likelihood estimation, computerized adaptive testing (CAT) software weights all of the following except ability.

What is CAT testing software?A type of computer-based test called computerized adaptive testing (CAT) adjusts to the examinee's degree of proficiency. It has also been referred to as customized testing for this reason.In other words, it's a type of computer-administered exam where the choice of the next item or group of things is based on how accurately the test-taker answered the most recent series of questions.Based on what is known about the examinee from prior questions, CAT picks questions in a sequential manner to maximize test accuracy. From the perspective of the test taker, the exam's complexity appears to be tailored to their level of competence.

Learn more about  CAT testing software refer to :

https://brainly.com/question/14284175

#SPJ4

14. calculate the stopping distance if landing with a 10 knot headwind on a runway at 7000 ft. msl (assume icao standard conditions).

Answers

The stopping distance is 4500 m/s

How to calculate stopping distance ?

The distance travelled between the moment the body decides to stop a moving vehicle and the moment the vehicle comes to a complete stop is known as the stopping distance. The stopping distance, indicated by the letter d, is dependent on a number of variables, including as the road's surface and the driver's reflexes.

You must maintain a sufficient distance from the vehicle in front of you so that, if necessary, you can safely stop to avoid colliding with the vehicle.

Given ,

Initial velocity = 7000

That is half of intial velocity = 450

Stopping distance = 450*10

= 4500 m/s

Therefore the stopping distance is 4500 m/s

To learn more about stopping distance refer to :

https://brainly.com/question/24020960

#SPJ4

glycerin at 380 c flows through a horizontal 9 mm diameter pipe with a pressure drop of 120 kpa/m. find the discharge and the reynolds number.

Answers

With a pressure drop of 120 kpa/m, glycerin at 380 c flows through a horizontal pipe with a 9 mm diameter. The Reynolds number is 3.807 after the discharge.

pressure drop=32μVL/D²

120*10³=32*0.95*V*1/(9*10⁻³)²

Velocity V=0.329 m/sec

discharge =AV

=π(9*10⁻³)²/4*0.319

pressure drop=2.02*10⁻⁵ m³

then,

Reynolds number=VD/γ

=δVD/μ

1.26*10³*0.319*9*10⁻³/0.95

=3.807

By measuring the proportion of inertial and viscous forces, the Reynolds number aids in the prediction of flow patterns in various fluid flow scenarios. Laminar flow typically predominates in low Reynolds numbers flows while turbulent flow predominates in high Reynolds numbers flows.

Learn more about Reynolds number here:

https://brainly.com/question/12977616

#SPJ4

what is the appropriate superelevation rate for a curve with a 1,200-ft radius on highway with a design speed of 60 mi/h?

Answers

A curve should superelevate at a rate of 6%.A 10% maximum superelevation has been advised for highways with hills that are not snow-bound.

How much super elevation can you get in total?Taking into account this mixed traffic, the IRC set a 7.0% or 0.07 maximum limit of superelevation on plain and rolling terrains and in snow-covered areas. A 10% maximum superelevation has been advised for highways with hills that are not snow-bound.By dividing the distance between the normal crown and full super by the transition length, one may calculate the rate of change in superelevation. 1,2000 - 60 = 11,940 Similar to the transition at the curve's beginning end, the rate of change is constant.      

To learn more about Superelevation refer to:

https://brainly.com/question/29357625

#SPJ4

A long, V-shaped part is heat treated by suspending it in a tubular furnace with a diameter of 2 m and a wall temperature of 925 K. The "vee is 1-m long on a side and has an angle of 60 Furnace, T Part, Tp If the wall of the furnace and the surfaces of the part may be approximated as blackbodies and the part is at an initial temperature of 300 K, what is the net rate of radiation heat transfer per unit length to the part, in W/m?

Answers

The part's net radiation heat transfer rate, expressed as a rate per unit length, isQ=123.4Kw/m

Given

temperature of 925 K

diameter of 2 m

we know that F11+f12+f13=1

F11+F13=1

so

F11=F13=0.5

A1F13=A3F31

=2L*1*0.5

2*1*1*0.5

A1F13=1

Similary F23 =1

A3F32=2

Therefore

A1F13=1

A3F32=2

T3=925k

T1=T2=300k

Q=1*σ*(925⁴-300⁴)+2*σ*(925⁴-300⁴)

=3*σ*(925⁴-300⁴)

=3*5.67*10⁻⁸*(925⁴-300⁴)

Therefore net radiation heat transfer rate

Q=123.4Kw/m

Learn more about radiation here:

https://brainly.com/question/13934832

#SPJ4

5/90 determine the reactions at a for the cantilever beam subjected to the distributed and concentrated loads.

Answers

Az = 0, Ay = 8 kN, and MA = 21 kN m CCW are the reactions at a for the cantilever beam subjected to the distributed and concentrated loads.

What happens when a cantilever beam?

The bending moment and moment reaction are equivalent at the cantilever beam's wall. The bending moment is 0 at the free end. The associated bending moment reaches its highest value at the point where the shear force crosses the zero axis.

What is the cantilever beam formula?

And Kef f=3EI/L3x is the effective spring constant for a point force applied to the cantilever's end. The displacement at the end of the beam is w(x=Lx)=qL48EI, and the restoring force, Keffw, opposes the applied force.

To know more about cantilever visit:-

https://brainly.com/question/13254986

#SPJ4

tech a says that small vacuum leaks can be found with a vacuum gauge. tech b says that the catalytic converter is typically located after the muffler. who is correct?

Answers

Both are true. Tech A claims that a vacuum gauge can be used to locate tiny vacuum leaks. According to tech B, the catalytic converter is usually placed behind the muffler.

Which of the following links the catalytic converter to the exhaust manifold?

Tailpipe. The catalytic converter has cleaned up the exhaust gases, which are then sent out of the car and into the atmosphere via the tailpipe, the last link in the exhaust system.

Which of the following exhaust system parts aids in lowering exhaust emissions?

Hazardous pollutants from engine exhaust are decreased by the catalytic converter. The converter, which is situated between the exhaust manifold and the muffler, works with heat and metals that serve as catalysts.

To know more about vacuum gauge visit:-

https://brainly.com/question/20989381

#SPJ4

A large-particle composite consisting of tungsten particles within a copper matrix is to be prepared. If the volume fractions of tungsten and copper are 0.18 and 0.82, respectively, estimate the upper limit for the specific stiffness of this composite given the data that follow.
Specific Gravity Modulus of Elasticity (GPa)
Copper 8.9 110
Tungsten 19.3 407

Answers

Using the information provided, 19.65 GPa is the maximum specific stiffness of the composite that can be calculated.

We provide;

Copper has a specific gravity of _cu = 8.9.

Tungsten has a specific gravity of 19.3 (_tu).

Copper's elasticity modulus is 110 GPa.

E tu = 407 GPa is the tungsten's elasticity modulus.

Tungsten volume fraction: V tu = 0.7

Copper volume percent, V cu = 0.3

1) The maximum rigidity permitted;

Let's use the formula to determine the modulus of elasticity's maximum value;

E u is equal to (E cu V cu) plus (E tu V tu).

E u = (110 × 0.3) + (407 × 0.7)

E u = 317.9 GPa

The formula yields an upper bound for the specific gravity;

(_cu V cu) + (_tu V tu) = _u

ρ u = (8.9 × 0.3) + (19.3 × 0.7)

ρ u = 16.18

E/u = Specific stiffness

Stiffness specific = 317.9/16.18

Specific stiffness upper limit = 19.65GPa

Learn more about specific here-

https://brainly.com/question/19819958

#SPJ4

.what is the generator for this design? b. what is the resolution of this design? c. estimate the factor effects. which effects are large? d. does a residual analysis indicate any problems with the underlying assumptions? e. draw conclusions about this filling process

Answers

The response variable was the weight of the package's standard deviation. The plan and collected data are as follows.

a)the generator for this design is E=-ABCD

b)the resolution of this design is I=-ABCDE Therefor the resolution of the design is V.

c)estimate the factor effects there is 3 larger effcts namely E=-0.4700,BE=-0.4050,DE=-0.3150

d)Construct a linear regrassion model.The constant is estimated by the grand average and the regression coefficent are estimated by one-half the corresponding effect estimates.

If the underlying assumptions have any issues, the residual analysis will show them.

Y=1.22625+0.04375x₂-0.01875x₄+0.2350x₅-0.08125x₂x₄-0.1575x₄x₅

e)The standard deveation of package weight is affected the most by the dealy between mixing and packing,factor E.Also, its intreaction with the temperature factor B,BE and with the batch weight factor D,DE are important.

Learn more about standard deveation here:

https://brainly.com/question/28210741

#SPJ4

A hollowed long bone is under axial loading (uniform) of 2000 N. The marrow cavity is assumed uniform of 15 mm in diameter (figure). The outer diameters are changed from 20 mm to 30 mm. Assuming E=18GPa, and v=0.30, find σ xx ,ε xx, at x=0,x=L/2, and x=L. Find the total deformation, δ(x).L=500 mm. The implant and the bone are connected with same δ. (40 pts)

Answers

Based on their forms, the 206 bones that make up the adult skeleton are separated into five groups. Each bone's category shape has a certain function due to the relationship between its shapes and functions.

An object with a long bone has a cylindrical shape and is longer than it is wide. But keep in mind that the phrase refers to a bone's form, not its size.

A short bone is one that is roughly equal in length, width, and thickness and has a cube-like shape. The carpals in the wrists and the tarsals in the ankles are the only short bones in the human skeleton.

Although a flat bone is often thin, it is also sometimes curved, so the phrase "flat bone" is somewhat misleading.

A bone is considered irregular if it lacks an obviously identifiable shape and so does not fall under another category.

A sesamoid bone is a tiny, round bone that resembles a sesame seed, as the name implies. These bones develop in tendons, the tissue sheaths that connect bones to muscles, where a lot of joint pressure is produced.

To know more about bone click here:

https://brainly.com/question/14810294

#SPJ4

technician a says that diesel engines supply only enough air to completely burn all the fuel in the combustion chamber. technician b says that diesel engines supply excess air to the combustion chamber to completely burn all the fuel in the combustion chamber. who is correct?

Answers

Engineers may create diesel engines with higher compression ratios than gasoline engines because diesel has a higher compression resistance and is denser than light distillate fuels.

The thermal efficiency of an engine increases with increasing compression ratio. Shaker, circulation, and spray jet systems are three ways that engine oil is utilized to assist in cooling pistons. the diesel engine. a fuel-burning engine that runs on diesel. Fuel oil is directly injected into the cylinders of a diesel engine. The air itself is hot enough to ignite the diesel fuel without a spark due to the extreme compression. Cycle with four strokes.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

for some transformation having kinetics that obey the avrami equation (equation 10.17), the parameter n is known to have a value of 2.6. if, after 150 s, the reaction is 50% complete, how long (total time) will it take the transformation to go to 90% completion? enter your answer in accordance to the question statement s

Answers

The time taken is t = 259.04 sec will it take the transformation to go to 90% completion.

Johnson Mehl Avrami developed the Avrami equation, which is used to explain how crystalline solids change from one phase to another while maintaining a constant temperature. At constant temperature, solids change from one phase to another according to the Avrami equation. It can be applied broadly to various phase shifts in materials, such as chemical reaction rates, and can even be useful in assessments of ecological systems. It can particularly characterize the kinetics of crystallization. The Avrami equation gives us Y= 1 - e - Ktn, where Y = 50% T. Time of reaction completion is 148 seconds, and n = 1.8 is obtained by multiplying all values by 1. K \s 0.5=1- e^{-K*148^1.8} \s e^{-K*148^1.8} = 0.5

Taking both sides of the log

-K*148^{1.8} = -0.693 \s

K=8.59 * 10-5,

GIVEN THAT

0.85 = 1 - e

^{- 8.59 * 10^{-5} *t^1.8} \s e^{- 8.59 * 10^{-5} *t^1.8}

= 0.15

Taking the log on both sides: 8.59 x 10-5 t, t

= 259.04 sec,

t = -1.897 s

Learn more about system here-

https://brainly.com/question/19770086

#SPJ4

Which of the following are fundamental intuitions behind collaborative filtering? A) Similar users will rate the items similarly B) Similar users will not rate the items similarly C) Similar items will be rated similarly Answer choices Select only one option Only A and B
Only B and C Only A and C Only A

Answers

The statement that are fundamental intuitions behind collaborative filtering is Only A. The fundamental intuition behind collaborative filtering are similar users will rate the items similarly.

To point some of the limitations of content-based filtering, collaborative filtering uses similarities between users and items simultaneously to provide recommendations. The example of collaborative filtering is collaborative filtering give the recommendation system as preferences in television programming could analyze about which television show a user should like given a partial list of that user's tastes (likes or dislikes). There are two main kind of Collaborative Filtering:

User-based, is used to measure the similarity between target users and other users. Item-based, is used to measure the similarity between the goods that target users rate or interact with and other items.

Learn more about the collaborative filtering here, https://brainly.com/question/14747907

#SPJ4

Other Questions
mr wang works in a recycling center recyclable materials arrive at the center mixed together workers use magnets separate steel cans from other items which two statements are true about the force between a steel can and a magnet solve for U3u 2 = 8U= do you think attendance to lectures affects performance on final exam? a model to explain the standardized outcome on a final exam (stndfnl) in terms These types of communities are clusters of 10-30 individually owned housing units where families of all ages can live interdependently.A. Virtual villagesB. IntentionalC. CohousingD. Niche Ron Company has the following commission schedule: Commission rate 2% 3.5% Sales Up to $80,000 Excess of $80,000 to $100,000 More than $100,000 Calculate the gross earning. Gross earning Employee Pat Maninen Total sales 154,000 The following coordinate plane shows three of the vertices of a rectangle. On an 8 by 8 coordinate grid, T is plotted 1 unit right and 4 units up from the origin. P is plotted 6 units right and 2 units up from the origin. Z is plotted 3 units right and 5 units up from the origin. What are the coordinates of Point Z? ( Choose... ) What are the coordinates of Point P? ( Choose... ) Which point has coordinates ( 1 , 4 ) ? Choose... In order to create a rectangle using these points as three of the vertices, what coordinates should be used for the fourth vertex? ( Choose... ) iii. Balance the equations for atoms O and H using H0 and H*. (.5 point) messer corporation sells recreational vehicles (rv). at the beginning of the year, they had one rv in inventory costing $40,000. they purchased another rv for $42,000. they sold one of the rvs for $57,500. how much is gross profit using the last-in, first-out (lifo) method? 2)Qu les recomienda Roxana Morduchowicz a los adultos? The table shows the proportional relationship between the price for a certain number of buckets of golf balls at a driving range. Buckets 3 5 7Price (dollars) 28. 50 47. 50 66. 50Determine the constant of proportionality. 9. 5 10. 5 18. 25 28. 5 a partnership agreement provides that, at sale, cash proceeds are distributed first to mr. smith in an amount equal to his original investment less any cash distributions previously received, then split 50-50 between mr. smith and ms. jones. assume that the cash flows from sale are $1 million. how much would mr. smith receive if his initial investment was $400,000 and he previously received $25,000 in distributions? If you were a southerner living in Georgia during Reconstruction, how would you view the Federal government's decision to deploy troops to the South?If you were a northerner, would you, as a voter, put pressure on your government to improve the lives of freedmen in the South or would you want the government to address labor needs in the North?How do you think living in different parts of the same society contribute to the way we interpret historical events, even the ones we live through?Was the Election of 1876 a "Great Betrayal" or was it necessary to end the military occupation of the South?Are terms like "Bayonet Rule" accurate descriptions of the military occupation of the South or propagandistic terms? A book sold 32,100 copies in its first month of release. Suppose this represents 8.2% of the number of copies sold to date. How many copies havebeen sold to date?Round your answer to the nearest whole number. what specific military tactics, units, and weapons were utilized in the siege of constantinople? according to the author, what role did mehmed ii play in this siege? how could you source this document? what is the term used in this book to refer to humans and our ancestors/relatives after our split with the african apes? an ideal gas is compressed from 900 cm3 to 425 cm3 while 125 j of heat energy is removed from it. if the gas's pressure remains constant at 400 kpa during the compression, how much work was done by the gas? a testcross involves an individual with the dominant phenotype but unknown genotype being crossed with an individual that has ano genotype Last year, 769 of the 1,307 residents in a small town owned more than one vehicle.Use this historical data to find the probability that a randomly selected resident in this small town owns more than one vehicle. when using email marketing, what is the ideal weekly email frequency for marketing and communicating with clients? amuel reports that he has a foot fetish and he is bothered by it. in therapy, he imagines a shoe and then immediately imagines a negative stimulus. the behavioral approach being used is: