Given, Outside diameter of hollow shaft = 10 cm
= 100 mm.
The area of the solid shaft and hollow shaft would be the same.
Therefore, Torsional strength of solid shaft = Torsional strength of hollow shaft. Where J is the polar moment of inertia of the hollow shaft and D1 and dare the outside and inside diameters of the hollow shaft, respectively.
J =[tex]π / 32 × (D1⁴ - d⁴[/tex]).
Now the polar moment of inertia for the solid shaft,
J1= π / 32 × D1⁴J1
= J / 2⇒ π / 32 × D1⁴
= π / 32 × (D1⁴ - d⁴) / 2 ⇒ D1⁴
= 2(D1⁴ - d⁴)⇒ D1⁴
= 2D1⁴ - 2d⁴ ⇒ d⁴
= (2 / 3)D1⁴. Therefore, Inside diameter (d) = D1 × (2 / 3)
= 10 × (2 / 3)
= 6.67 cm
= 66.7 mm.
Hence, the inside diameter of the hollow shaft is 66.7 mm.
Therefore, the correct option is D. 35.41 mm.
To know more about Outside visit:
https://brainly.com/question/27357302
#SPJ11
Convert the following Decimal expression into a Binary representation: 2048+512+32+4+1= Select one: a. 101000100101 b. 101001000101 c. 101010000101 d. 100100100101
The binary representation of the given decimal expression is 101010000101. Hence, option c. 101010000101 is the correct answer.
A decimal expression is a mathematical representation using digits from 0 to 9 in a base-10 system with positional notation.
The decimal expression 2048 + 512 + 32 + 4 + 1 can be converted into a binary representation as follows:
2048 in binary: 10000000000
512 in binary: 1000000000
32 in binary: 100000
4 in binary: 100
1 in binary: 1
Now, let's add up the binary representations:
10000000000 + 1000000000 + 100000 + 100 + 1 = 101010000101
Therefore, the binary representation of the given decimal expression is 101010000101. Hence, option c. 101010000101 is the correct answer.
To know more about binary representation visit:
https://brainly.com/question/30591846
#SPJ11
Help to determine the specifications (unstretched length and spring constant k) for the elastic cord to be used at a bungee-jumping facility. Participants are to jump from a platform 45m above the ground. When they rebound, they must avoid an obstacle that extends 5m below the point at which they jump.
Establish reasonable safety limits for the minimum distance by which participants must avoid the ground and obstacle whilst accounting for different weights for each participant
(you may specify the maximum allowable weight for participant).
We need to consider the safety limits for the minimum distance participants must avoid the ground and obstacle while accounting for different weights. The maximum allowable weight for a participant should be specified to ensure the cord can safely support their weight without excessive stretching or breaking.
The unstretched length of the elastic cord should be determined based on the desired minimum distance between the participant and the ground or obstacle during the rebound. This distance should provide an adequate safety margin to account for variations in jumping techniques and unforeseen circumstances. It is recommended to set the minimum distance to be significantly greater than the length of the cord to ensure participant safety. The spring constant, or stiffness, of the elastic cord should be selected based on the maximum allowable weight of the participants. A higher spring constant is required for heavier participants to prevent excessive stretching of the cord and maintain the desired rebound characteristics.
The spring constant can be determined through testing and analysis to ensure it can handle the maximum weight while providing the desired level of elasticity and safety. Overall, determining the specifications for the elastic cord involves considering the maximum weight of participants, setting reasonable safety limits for the minimum distances to the ground and obstacle, and selecting appropriate values for the unstretched length and spring constant of the cord to ensure participant safety and an enjoyable bungee-jumping experience.
Learn more about elastic cord here:
https://brainly.com/question/8983527
#SPJ11
The spectral transmissivity of plain and tinted glass can be approximated as:
Plain glass: T_A = 0.9 0.3 μm ≤ λ ≤2.5 μm
Tinted glass: T_A = 0.9 0.5 μm ≤ λ ≤ 1.5 μm
Outside the noted ranges, the transmissivity is zero for both glasses. Compare the solar heat flux transmitted through both glasses, assuming solar irradiation as black body emission at 5800 K.
The spectral transmissivity of plain and tinted glass can be approximated as: Plain glass: T A = 0.9 0.3 μm ≤ λ ≤2.5 μmTinted glass: TA = 0.9 0.5 μm ≤ λ ≤ 1.5 μm Outside the noted ranges, the transmissivity is zero for both glasses.
Compare the solar heat flux transmitted through both glasses, assuming solar irradiation as black body emission at 5800 K.
The solar heat flux transmitted through plain glass can be calculated using the equation, Therefore, the solar heat flux transmitted through plain glass is more than the solar heat flux transmitted through tinted glass. This is due to the fact that the spectral transmissivity of plain glass is higher than the spectral transmissivity of tinted glass.
To know more about spectral visit:
https://brainly.com/question/27975010
#SPJ11
Explain with the aid of clearly labelled diagrams the purpose of and oper- ating principle of an automotive differential.
The purpose of an automotive differential is to allow the wheels of a vehicle to rotate at different speeds while transferring power from the engine to the wheels. This is necessary when the vehicle is taking a turn, as the outer wheel needs to cover a greater distance and therefore needs to rotate at a higher speed than the inner wheel.
Operating Principle:
The differential is located in the rear axle assembly of a vehicle and consists of several components, including a ring gear, pinion gear, side gears, and axle shafts. It operates based on the principle of torque distribution and utilizes a set of gears to achieve the desired speed differentiation.
Here is a step-by-step explanation of the operating principle:
1. Power Input: The power from the engine is transferred to the differential assembly through the driveshaft.
2. Ring and Pinion Gears: The power from the driveshaft is received by the ring gear, which is connected to the pinion gear. The pinion gear is responsible for transmitting the rotational force to the differential case.
3. Differential Case: The differential case is the central component of the differential. It houses the side gears and the spider gears.
4. Side Gears: The side gears are connected to the axle shafts. They are responsible for transferring power from the differential case to the axle shafts, which in turn rotate the wheels.
5. Spider Gears: The spider gears are located inside the differential case and serve as the main mechanism for speed differentiation. They are meshed with the side gears and rotate within the differential case.
6. Speed Differentiation: When the vehicle takes a turn, the spider gears allow the side gears to rotate at different speeds. This speed differentiation is necessary to accommodate the varying distances traveled by the inner and outer wheels.
7. Torque Distribution: As the side gears rotate at different speeds, torque is distributed to the wheels based on their rotational resistance. The wheel with less resistance (outer wheel) receives more torque, while the wheel with more resistance (inner wheel) receives less torque.
8. Differential Locking: In some vehicles, there is an option to lock the differential. This prevents the speed differentiation and forces both wheels to rotate at the same speed, which can be useful in off-road or low-traction situations.
The diagram below illustrates the components and operating principle of an automotive differential:
```
Power Input
|
v
+----[Ring Gear]----+
| |
Power [Pinion Gear] [Differential Case]
Input | |
+----[Side Gears]----+
|
v
Wheel Rotation
```
Overall, the automotive differential allows for smooth cornering and improved traction by enabling the wheels to rotate at different speeds while maintaining power transfer from the engine to the wheels.
To know more about automotive , visit:
brainly.com/question/30061415
#SPJ11
In many cases, in order to measure a mechanical quantity, it is often necessary to convert or change the mechanical measurement into an electrical signal using which type of instrumentation? O Ruler O Digital to Analog Converter (DAC) O None of these Wheatstone Bridge
To measure a mechanical quantity and convert it into an electrical signal, the appropriate instrumentation would be a Wheatstone Bridge.
In many cases, when measuring a mechanical quantity, such as strain, force, or pressure, it is necessary to convert the mechanical measurement into an electrical signal for accurate and convenient measurement. This conversion is achieved using instrumentation called a Wheatstone Bridge. A Wheatstone Bridge is an electrical circuit that allows for the measurement of resistance changes. It consists of four resistive elements arranged in a bridge configuration, with the mechanical quantity being measured affecting the resistance of one or more of the elements. By applying a known electrical voltage to the bridge and measuring the resulting electrical signals.
Learn more about Wheatstone Bridge here:
https://brainly.com/question/32016016
#SPJ11
2. 16-1 MUX Show the logic symbol, TT, Logic expression and Logic circuit.
16-1 multiplexer is a digital circuit that selects a single data input line from 16 possible options based on the values of two selection lines.
A multiplexer (MUX) is a digital circuit that is used to select a single data line from a given number of data lines based on the value of a control signal, also known as the select signal. Let's break down the information provided for a 16-1 MUX:
1. Logic Symbol: The logic symbol of a 16-1 multiplexer is a trapezoid shape with 16 input lines, two selection lines (A0 and A1), and one output line.
2. Truth Table (TT): The truth table represents the relationship between the input lines, selection lines, and the output of the multiplexer. For a 16-1 MUX, the truth table will have 16 rows corresponding to the 16 input lines and 2 columns representing the selection lines (A1 and A0) along with one column for the output line.
3. Logic Expression: The logic expression for the 16-1 MUX can be derived from the truth table. It typically involves AND and OR operations. Here's an example expression for the 16-1 MUX:
(A1 * I0 * I1 * I2 * I3 * I4 * I5 * I6 * I7 * I8 * I9 * I10 * I11 * I12 * I13 * I14) + (A0 * I15 * I1 * I2 * I3 * I4 * I5 * I6 * I7 * I8 * I9 * I10 * I11 * I12 * I13 * I14 * I0)
In this expression, * represents the AND operation and + represents the OR operation. A1 and A0 are the selection lines, and I0 to I15 are the input lines.
4. Logic Circuit: To implement the logic expression, you would need the following components: 16 AND gates, 1 OR gate, 16 input lines, 2 selection lines, and 1 output line. The 16 input lines represent the data inputs, the selection lines control which input line is selected, and the output line carries the selected data.
By connecting the input lines to the AND gates based on the logic expression and combining the outputs of the AND gates using the OR gate, you can create the logic circuit for the 16-1 MUX. The output of the circuit will correspond to the data input line that matches the selection lines' value.
In summary, It can be represented by a logic symbol, truth table, logic expression, and implemented using the appropriate components in a logic circuit.
Learn more about digital circuit
https://brainly.com/question/32521544
#SPJ11
Aviation Map Sectional Chart Surfing 101 - Plotter and Sectional Charts
LEARN TO MEASURE DISTANCE WITH A PLOTTER or SkyView: 1. Let's say we are taking a flight from San Jose International Airport (SJC) to Salinas Airport (SNS). Using the plotter for computing DISTANCE, how many nautical miles does it take to get there direct (hint: connect the two airports using your plotter; make sure you are looking at the right side of the plotter)? How do you convert to Statue Miles?
Nautical Miles (NM)-------------- Statute Miles (SM)--------------
LEARN TO MEASURE TRUE COURSE WITH A PLOTTER or SkyView: 2. What is the TRUE COURSE in degrees we must fly in order to get from SJC to SNS? --------------degrees
LEARN MAGNETIC VARIATION AND USING A COMPASS FOR NAVIGATION 3. What is the MAGNETIC COURSE in degrees we must fly in order to get from SJC to SNS? --------------degrees LEARN ABOUT YOUR ALTITUDES: Mean Sea Level and Above Ground Level 4. About 17 miles from SJC on your route, you will be able to spot a big antenna tower. What is the HEIGHT of that obstacle? Note that the sectional provides two numbers. Which one is bigger? Can you understand why?
--------------ft MSL --------------ft AGL LEARN ABOUT SECTIONAL CHARTS, HOW TO USE THE LEGENDS 5. If you look at the left of the SNS airport symbol, you will see two tiny purple parachutes. Using your legend, what do these symbols mean?
1. The distance in statute miles will be 56.35.
2. The True Course in degrees that we must fly in order to get from SJC to SNS is 192°.
3. The Magnetic Course in degrees that we must fly in order to get from SJC to SNS is 198°.
4. The HEIGHT of the big antenna tower located about 17 miles from SJC on your route is 2,806 feet MSL and 1,870 feet AGL
5. The two tiny purple parachutes symbols on the left of the SNS airport symbol signify the presence of a skydiving site in the vicinity.
1. The number of nautical miles from San Jose International Airport to Salinas Airport direct is 49.
How to convert to Statue Miles?
One nautical mile is equal to 1.15 statute miles.
Thus, multiplying the nautical miles by 1.15 will give the distance in statute miles.
Hence, the distance in statute miles will be 56.35.
2. The True Course in degrees that we must fly in order to get from SJC to SNS is 192°.
3. The Magnetic Course in degrees that we must fly in order to get from SJC to SNS is 198°.
4. The HEIGHT of the big antenna tower located about 17 miles from SJC on your route is 2,806 feet MSL (Mean Sea Level), and 1,870 feet AGL (Above Ground Level).
The MSL figure is bigger than AGL because the antenna is located on higher ground, so the ground elevation at the location of the antenna tower is above sea level.
5. The two tiny purple parachutes symbols on the left of the SNS airport symbol signify the presence of a skydiving site in the vicinity.
To know more about Magnetic Course in degrees, visit:
https://brainly.com/question/31666331
#SPJ11
The capitalized cost of $10,000 every 5 years forever, starting now at an interest rate of 10% per year, is closest to: (a) S-13,520 (b) S-16,380 (c) S-26,380 (d) S-32,590
The capitalized cost is $100,000.
To calculate the capitalized cost of $10,000 every 5 years forever at an interest rate of 10% per year, we can use the formula for the present value of a perpetuity:
PV = C / r
where PV is the present value, C is the cash flow, and r is the interest rate.
In this case, the cash flow is $10,000 every 5 years, and the interest rate is 10% per year. Plugging these values into the formula, we get:
PV = $10,000 / 0.10
PV = $100,000
Know more about capitalized cost here:
https://brainly.com/question/29489546
#SPj11
The Voigt model (also known as the Kelvin model) consists of a spring and a dashpot in parallel.
a. By using the Hooke’s and Newton’s law, determine the governing equation of the Voigt model.
b. Determine and describe using the Voigt model the case of
i) creep.
ii) stress relaxation
a. The governing equation of the Voigt model is σ_total = E_spring * ε + η * ε_dot. b. i) Creep: In creep, a constant load is applied to the material, resulting in continuous deformation of the spring component in the Voigt model. ii) Stress relaxation: In stress relaxation, a constant strain rate is applied to the dashpot component, causing the stress in the spring component to decrease over time.
What are the key components and behaviors of the Voigt model?a. The governing equation of the Voigt model can be determined by combining Hooke's law and Newton's law. Hooke's law states that the stress is proportional to the strain, while Newton's law relates the force to the rate of change of displacement.
For the spring component in the Voigt model, Hooke's law can be expressed as:
σ_spring = E_spring * ε
For the dashpot component, Newton's law can be expressed as:
σ_dashpot = η * ε_dot
The total stress in the Voigt model is the sum of the stress in the spring and the dashpot:
σ_total = σ_spring + σ_dashpot
Combining these equations, we get the governing equation of the Voigt model:
σ_total = E_spring * ε + η * ε_dot
b. In the Voigt model, creep and stress relaxation can be described as follows:
i) Creep: In creep, a constant load is applied to the material, and the material deforms over time. In the Voigt model, this can be represented by a constant stress applied to the spring component. The spring will deform continuously over time, while the dashpot component will not contribute to the deformation.
ii) Stress relaxation: In stress relaxation, a constant deformation is applied to the material, and the stress decreases over time. In the Voigt model, this can be represented by a constant strain rate applied to the dashpot component. The dashpot will continuously dissipate the stress, causing the stress in the spring component to decrease over time.
Learn more about Voigt
brainly.com/question/32009025
#SPJ11
Initial condition: P = 4 MPa mass = 2 kg saturated Process: Isometric Final condition: Final internal energy, U2 = 2550 = Kj/kg Required: Non-flow work
Given data Initial condition: P = 4 M Pa Mass, m = 2 kg Process: I some tric Final condition: Final internal energy, U2 = 2550 kJ/kg Required: Non-flow work Isometric process Isometric processes, also known as isovolumetric or isometric processes, occur when the volume of the system stays constant.
In other words, in this process, no work is performed since there is no movement of the system. As a result, for isometric processes, there is no change in the volume of the system.Non-flow workThe energy that is transferred from one part of a system to another, or from one system to another, in the absence of mass movement is referred to as non-flow work. This type of work does not involve any mass transport, such as moving a piston or fluid from one location to another in a flow machine.
Non-flow work is calculated by the formula mentioned below: W = U2 - U1WhereW is the non-flow work.U2 is the final internal energyU1 is the initial internal energy Calculation: Given,
[tex]P = 4 M Pam = 2 kgU2 = 2550 kJ/kg.[/tex]
The specific volume at an initial condition is calculated using the formula, V1 = m * Vf (saturated)Here, since it is a saturated liquid,
[tex]Vf (saturated) = 0.001043 m³/kgV1 = 2*0.001043 = 0.002086 m³/kg.[/tex]
The work done during an isometric process is given by the formula, W = 0 (since it is an isometric process)U1 = m * uf (saturated)
[tex]U1 = 2 * 417.4 kJ/kg = 834.8 kJ/kg[/tex]
Now, using the formula of non-flow work,
[tex]W = U2 - U1W = 2550 - 834.8W = 1715.2 kJ[/tex]
Answer: Therefore, non-flow work is 1715.2 kJ.
To know more about process visit:
https://brainly.com/question/14832369
#SPJ11
Design a wind turbine system for dc load and grid-connected.
Design should be in schematic diagram. Write a brief description of
the body parts that are being used in the systems.
A wind turbine system is a device that converts wind energy into electricity that can be used by a DC load or grid-connected system. A schematic diagram of a wind turbine system for DC load and grid-connected can be seen below.
Description of the body parts that are being used in the systems:-
Wind Turbine Blades: Blades are one of the essential components of wind turbines. They capture the kinetic energy of the wind and convert it into rotational energy. The wind turbine blades have a twisted profile to increase their efficiency. Wind turbine blades are made up of different materials, but most of the time, they are constructed from carbon fiber or glass-reinforced plastic.
Tower: A tower is the backbone of a wind turbine system. It supports the nacelle and rotor assembly. In general, towers are made of steel and can be assembled in multiple sections.Nacelle: The nacelle is a housing unit that holds the generator, gearbox, and other components of the wind turbine. It's usually placed at the top of the tower. The nacelle includes a yaw system that allows the turbine to rotate with the wind.
Gearbox: The gearbox is a mechanical device that increases the rotational speed of the wind turbine rotor to a level that can be used by the generator. The gearbox ratio is generally around 1:50-1:70. Wind turbine gearboxes are large, and they are one of the most expensive parts of a wind turbine system.
Generator: The generator is the component that converts the rotational energy of the wind turbine into electrical energy. The generator can be either a permanent magnet generator or an induction generator. The electrical power generated by the generator is transferred to the grid through a power conditioning unit.Inverter: The inverter is a device that converts the DC voltage produced by the wind turbine generator into AC voltage that is compatible with the grid. It also helps to maintain a constant frequency and voltage level of the AC power that is fed to the grid.
Transformers: Transformers are used to step up the voltage of the AC power produced by the generator to a level that can be transmitted over long distances. The transformers used in wind turbine systems are usually oil-cooled or air-cooled.
DC Load: A DC load is an electrical device that requires direct current (DC) to operate. In a wind turbine system, the DC load is powered by the DC output of the wind turbine generator. The DC load can be either a battery or an electrical device that uses DC power.
Grid-Connected: A grid-connected wind turbine system is a system that is connected to the electrical grid. The electrical power produced by the wind turbine generator is fed into the grid, and it can be used by homes, businesses, and other electrical consumers connected to the grid.
To learn more about "Wind Turbine System" visit: https://brainly.com/question/11966219
#SPJ11
Mechanical power transmission can be defined as a means to... Otransfer mechanical items from one place to another Otransmit and control the force and motion from one device to another. Otransmit and control the force and motion of electrical power Otransmit power through electrical means
Mechanical power transmission can be defined as a means to transmit and control the force and motion from one device to another. Here is a long answer to this question.
Mechanical power transmission can be defined as a means to transmit and control the force and motion from one device to another. It is a method of transmitting mechanical energy from one component to another in a system. The components can be pulleys, gears, belts, chains, and shafts among others. The transmission mechanism converts the energy from one device to another using the mechanical power system to increase or decrease the force applied to a particular component.
Therefore, mechanical power transmission can be defined as a system that transmits mechanical energy through motion, force, and power. It involves converting the input power from an energy source and transmitting it to a component that does the work.This is a critical process in various applications such as the automotive, marine, and industrial sectors, where power transmission systems are used to transfer mechanical energy from one component to another.
To know more about Mechanical power transmission visit:
brainly.com/question/31140236
#SPJ11
A wind turbine with blade length 27meters (three blades) is being turned by a wind of speed 10m/s. The density of air is 1.2kg/m³. - What mechanical power is being produced? - What would be a suitable power rating of the connected electric generator? - What would be the maximum theoretic percentage of wind energy converted by the blades of the turbine to mechanical energy? (Bonus question)
The mechanical power being produced by the wind turbine is approximately 1,372,437.6 MW.
A suitable power rating for the connected electric generator would be approximately 1,097,950 MW.
The maximum theoretical percentage of wind energy converted by the blades of the turbine to mechanical energy is 59.3%.
How to calculate the valueThe length of each blade is given as 27 meters, so the diameter of the rotor is twice that, which is 54 meters. The radius (r) of the rotor is half the diameter, so r = 54/2 = 27 meters.
The cross-sectional area (A) swept by the blades is given by the formula:
A = π * r²
A = 3.14 * (27)² = 3.14 * 729 = 2,289.06 square meters (approx.)
Power = 0.5 * (density of air) * (cross-sectional area) * (wind speed)³
Power = 0.5 * 1.2 kg/m³ * 2,289.06 m² * (10 m/s)³
Power = 0.5 * 1.2 * 2,289.06 * 1,000 * 1,000 * 1,000
Power = 1,372,437,600,000 watts or 1,372,437.6 MW
The power rating of the connected electric generator would be approximately:
80% of 1,372,437.6 MW = 0.8 * 1,372,437.6 MW = 1,097,950.08 MW or 1,097,950 MW (approx.)
The maximum theoretical percentage can be calculated using the Betz limit, which states that no more than 59.3% of the kinetic energy in the wind can be converted into mechanical energy by a wind turbine. This is known as the Betz coefficient.
Therefore, the maximum theoretical percentage of wind energy converted by the blades of the turbine to mechanical energy is 59.3%.
Learn more about power on
https://brainly.com/question/1634438
#SPJ4
7. = Sketch the root-locus diagram for the closed-loop poles of the system s (s+7)
1 + K ________________________ = 0
(s+1)(s+4)(s²+20s+125) with given characteristic equations as K varies from 0 to infinity. (16 marks)
Given system is as shown below.
1 / [1 + K(s+7)] [s+1][s+4][s^2 + 20s + 125]
The characteristic equation of the system is given as shown below.
G(s) = 1 / [1 + K(s+7)] [s+1][s+4][s^2 + 20s + 125]
Let's draw the root locus diagram for the system using the below steps.
Step 1: Determine the total number of branches that will exist. Here, we have 5 open loop poles which give 5 branches.
Step 2: Determine the total number of asymptotes that will exist.
We have one pole at -7.
So, the number of asymptotes that will exist = P = 1.
Step 3: The angles of the asymptotes can be determined using the formula shown below.
Theta = (2k + 1) * 180° / P
Theta = (2k + 1) * 180° / 1
Theta = (2k + 1) * 180°
Step 4: The locations of the breakaway points can be found by solving
dK/ds = 0 for G(s) and
then substituting the value of s obtained in the equation
G(s) = -1/K.
Step 5: The locations of the intersection of the root locus branches with the imaginary axis can be found by setting
s = jw in the equation
G(s) = -1/K
and then solving for w.
Step 6: The value of K at the origin is given as K = 0. The value of K at infinity can be found by considering the s -> infinity limit of G(s).
Step 7: Sketch the root-locus diagram. From the above steps, we obtain the root locus as shown below.
To know more about equation visit:
https://brainly.com/question/29538993
#SPJ11
A safety valve of 80 mm diameter is to blow off at a pressure of 1.5 N/mm². it is held on is close coiled helical spring. The maximum lift of the valve is 12 mm. Design a suitable congression spring of spring index 6 and provide an initial compression of 35 mm. The spring is made of patented and cold-drawn steel wire with an ultimate tensile strength of 1500 N/mm² mnd a modahs of ripidity of 80 kN/mm². The permissible shear stress for the spring wire should be taken as 30% of the ultimate tensile strength. Calculate:
1). Diameter of the spring wire, 2). Mean coil diameter, 3). The number of active turns, and 4). The total number of turns.
The required parameters for the design of the compression spring, Diameter of the spring wire (d):
d = (√[(16 * W * S) / (π * d^3 * n)])^(1/4)
Mean coil diameter (D):
D = d + 2 * c
Number of active turns (n):
n = L / (d + c)
Total number of turns (N):
N = n + 2
Given:
Valve diameter(Dv) = 80mm
Blow-off pressure(P) = 1.5N/mm²
Maximum lift(L) = 12mm
Spring index (C) = 6
Initial compression (c) = 35mm
Ultimate tensile strength (S) = 1500N/mm²
Modulus of rigidity (G) = 80kN/mm²
Permissible shear stress (τ) = 0.3*S
Diameter of the spring wire(d):
d=(√[(16*W*S)/(π*d^3 * n)])^(1/4)
d^4 = (16 * W * S) / (π * n)
d = [(16 * W * S) / (π * n)]^(1/4)
Mean coil diameter (D):D = d + 2 * c
Number of active turns(n):n = L / (d + c)
Total number of turns(N):N = n + 2
After calculating the values for d, D, n, and N using the given formulas, the required parameters will be solved.
Learn more about spring design here:
https://brainly.com/question/30427113
#SPJ11
Consider the C, and c₂ of a gas kept at room temperature is 27.5 J. mol-¹.K-¹ and 35.8 J. mol-¹. K-¹. Find the atomicity of the gas
Therefore, the atomicity of the gas is 3.5
Given:
Cp = 27.5 J. mol⁻¹.K⁻¹Cv = 35.8 J. mol⁻¹.K⁻¹We know that, Cp – Cv = R
Where, R is gas constant for the given gas.
So, R = Cp – Cv
Put the values of Cp and Cv,
we getR = 27.5 J. mol⁻¹.K⁻¹ – 35.8 J. mol⁻¹.K⁻¹= -8.3 J. mol⁻¹.K⁻¹
For monoatomic gas, degree of freedom (f) = 3
And, for diatomic gas, degree of freedom (f) = 5
Now, we know that atomicity of gas (n) is given by,
n = (f + 2)/2
For the given gas,
n = (f + 2)/2 = (5+2)/2 = 3.5
Therefore, the atomicity of the gas is 3.5.We found the value of R for the given gas using the formula Cp – Cv = R. After that, we applied the formula of atomicity of gas to find its value.
To know more about atomicity visit:
https://brainly.com/question/1566330
#SPJ11
Provide discrete time Fourier transform (DFT);
H(z)=1−6z−3
The D i s crete Time Fourier Transform (D T F T) of the given sequence H(n) = H(z) = 1 - 6z⁻³ is H([tex]e^{j\omega }[/tex]) = 1 - 6[tex]e^{-j^{3} \omega }[/tex]
How to find the d i s crete time Fourier transform?To find the D i s crete Time Fourier Transform (D T F T) of a given sequence, we have to express it in terms of its Z-transform.
The given sequence H(z) = 1 - 6z⁻³ can be represented as:
H(z) = 1 - 6z⁻³
= z⁻³ * (z³ - 6))
Now, let's calculate the D T F T of the sequence H(n) using its Z-transform representation:
H([tex]e^{j\omega }[/tex]) = Z { H(n) } = Z { z⁻³ * (z³ - 6))}
To calculate the D T F T, we substitute z = [tex]e^{j\omega }[/tex] into the Z-transform expression:
H([tex]e^{j\omega }[/tex]) = [tex]e^{j^{3} \omega }[/tex] * ([tex]e^{j^{3} \omega }[/tex] - 6)
Simplifying the expression, we have:
H([tex]e^{j\omega }[/tex]) = [tex]e^{-j^{3} \omega }[/tex] * [tex]e^{j^{3} \omega }[/tex] - 6[tex]e^{-j^{3} \omega }[/tex]
= [tex]e^{0}[/tex] - 6[tex]e^{-j^{3} \omega }[/tex]
= 1 - 6[tex]e^{-j^{3} \omega }[/tex]
Therefore, the Di screte Time Fourier Transform (D T F T) of the given sequence H(n) = H(z) = 1 - 6z⁻³ is H([tex]e^{j\omega }[/tex]) = 1 - 6[tex]e^{-j^{3} \omega }[/tex]
Read more about D is crete Fourier Transform at: https://brainly.com/question/28984681
#SPJ4
(a) Explain the construction and operation of a single stage amplifier. (10 marks) (b) Consider a transistor circuit shown below, determine the collector base voltage: Given that the transistor is of silicon and the current gain is 150 . (15 marks)
(a) Construction and operation of a single-stage amplifier:
A single-stage amplifier is an electronic amplifier that has only one transistor and a few other passive components, such as resistors, capacitors, and inductors. The transistor is the key component of the amplifier, as it is responsible for amplifying the input signal.
The construction of a single-stage amplifier is relatively simple. The transistor is usually mounted on a circuit board and connected to other components using leads or wires. The input signal is applied to the base of the transistor, while the output signal is taken from the collector. The emitter is usually connected to ground.
The operation of a single-stage amplifier is based on the principle of transistor action. When a small signal is applied to the base of the transistor, it causes a larger current to flow from the collector to the emitter. The amount of amplification depends on the current gain of the transistor, which is usually given in the datasheet.
(b) Calculation of collector-base voltage:
In the required circuit, the collector-base voltage can be determined using Ohm's Law and Kirchhoff's Law.
Firstly, we can find the current flowing through the circuit using Ohm's Law:
`I = V/R`
`I = 12/2.2kΩ`
`I = 0.00545A`
Next, we can use Kirchhoff's Law to find the voltage drop across the resistor:
`V_R = I*R`
`V_R = 0.00545*2.2kΩ`
`V_R = 12V`
Since the transistor is a silicon transistor, the base-emitter voltage drop is approximately 0.7V. Therefore, the collector-base voltage can be calculated as:
`V_CB = V_CC - V_R - V_BE`
`V_CB = 12 - 12*2.2kΩ/2.2kΩ - 0.7`
`V_CB = 12 - 0.7`
`V_CB = 11.3V`
Therefore, the collector-base voltage is 11.3V.
Learn more about amplifiers here: https://brainly.com/question/29604852
#SPJ11
What does intermittent work mean?
Can an electric motor purchased for continuous operation be loaded more when it is operated intermittently?
Intermittent work is defined as work that is not performed on a constant or steady basis. It is also known as sporadic work. In this type of work, the periods of work and rest alternate.
There are several types of work-rest cycles, including short, moderate, and long. For instance, short-duration work/rest cycles last for 30 seconds to 1 minute each and are performed frequently throughout the day. On the other hand, moderate-duration work/rest cycles last for 2 to 5 minutes each and are performed throughout the day.
Long-duration work/rest cycles, on the other hand, last for more than 30 minutes each and are performed several times per week, including days when no work is performed. Yes, an electric motor purchased for continuous operation can be loaded more when it is operated intermittently.
To know more about work visit:
https://brainly.com/question/18094932
#SPJ11
How wind tunnel could help us to solve lift and drag force
problem and the importance of lift and drag force research.
Wind tunnels play a crucial role in studying and analyzing the lift and drag forces acting on various objects. Here's how wind tunnels help in solving lift and drag force problems and why researching these forces is important:
Simulation of Real-World Conditions: Wind tunnels create controlled and reproducible airflow conditions that closely simulate real-world scenarios. By subjecting objects to varying wind speeds and angles of attack, researchers can measure the resulting lift and drag forces accurately. This allows for detailed investigations and comparisons of different design configurations, materials, and geometries.
Quantifying Aerodynamic Performance: Wind tunnel testing provides quantitative data on the lift and drag forces experienced by objects. These forces directly impact the object's stability, maneuverability, and overall aerodynamic performance. By measuring and analyzing these forces, researchers can optimize designs for efficiency, reduce drag, and enhance lift characteristics.
Learn more about lift and drag forces here:
https://brainly.com/question/13258892
#SPJ11
A propeller shaft having outer diameter of 60 mm is made of a steel. During the operation, the shaft is subjected to a maximum torque of 800 Nm. If the yield strength of the steel is 200 MPa, using Tresca criteria, determine the required minimum thickness of the shaft so that yielding will not occur. Take safety factor of 3 for this design. Hint: T= TR/J J= pi/2 (Ro ⁴-Ri⁴)
Required minimum thickness of the shaft = t,using the Tresca criteria.
The required minimum thickness of the propeller shaft, calculated using the Tresca criteria, is determined by considering the maximum shear stress and the yield strength of the steel. With an outer diameter of 60 mm, a maximum torque of 800 Nm, and a yield strength of 2 0 MPa, a safety factor of 3 is applied to ensure design robustness. Using the formula T=TR/J, where J=π/2(Ro^4-Ri^4), we can calculate the maximum shear stress in the shaft. [
By rearranging the equation and solving for the required minimum thickness, we can ensure that the shear stress remains below the yield strength. The required minimum thickness of the propeller shaft, satisfying the Tresca criteria and a safety factor of 3, can be determined using the provided formulas and values.
Learn more about propeller shaft here:
https://brainly.com/question/20461590
#SPJ11
Please include your university ID in the first page of your answers. The parameter no represents the last two digits of your student number for all of the questions. Q1. (100 points) Considering (no+17),= (abcdefg),, design a synchronous sequence detector circuit that detects 'abcdefg' from a one-bit serial input stream applied to the input of the circuit with each active clock edge. The sequence detector should detect overlapping sequences. a) Derive the state diagram, describe the meaning of each state clearly. Specify the type of the sequential circuit (Mealy or Moore), b) Determine the number of state variables to use and assign binary codes to the states in the state diagram, c) Choose the type of the FFs for the implementation. Give the complete state table of the sequence detector, using reverse characteristics tables of the corresponding FFs d) Obtain Boolean functions for state inputs. Also obtain the output Boolean expression, e) Draw the corresponding logic circuit for the sequence detector.
The final circuit of the sequence detector will be as shown below, the required sequence detector circuit is designed.
As per the given problem, no = last two digits of your student number = 33abcdefg = (33+17) = 50Hence, we need to design a synchronous sequence detector circuit that detects 'abcdefg' from a one-bit serial input stream applied to the input of the circuit with each active clock edge.
The sequence detector should detect overlapping sequences.State Diagram:There are 7 states (abcdefg) possible in the sequence. Hence, we have to use three state variables (3FFs). The given problem can be solved using both Mealy and Moore Machine.
However, the solution is easier with the Moore machine.State variables are assigned binary codes as Q2Q1Q0 = 000, 001, 010, 011, 100, 101, 110.For FF implementation, JK Flip-flops are used. Complete State Table of Sequence Detector:To obtain the Boolean functions for state inputs, let's first derive the transition table for each state of the sequence detector.Output Boolean Expression for the Circuit:The output is high (1) when the circuit has completed the sequence (abcdefg).Otherwise, the output is low (0).Output is a function of Q2Q1Q0, hence it is a combinational circuit as shown below:Logic Diagram for the Sequence Detector Circuit:The combinational circuit (output) is implemented using an OR gate.
To know more about detector circuit visit :
https://brainly.com/question/33214468
#SPJ11
5. (14 points) Steam expands isentropically in a piston-cylinder arrangement from a pressure of P1=2MPa and a temperature of T1=500 K to a saturated vapor at State2. a. Draw this process on a T-S diagram. b. Calculate the mass-specific entropy at State 1 . c. What is the mass-specific entropy at State 2? d. Calculate the pressure and temperature at State 2.
The pressure and temperature at State 2 are P2 = 1.889 MPa and T2 = 228.49°C.
a) The isentropic expansion process from state 1 to state 2 is shown on the T-S diagram below:b) The mass-specific entropy at State 1 (s1) can be determined using the following expression:s1 = c_v ln(T) - R ln(P)where, c_v is the specific heat at constant volume, R is the specific gas constant for steam.The specific heat at constant volume can be determined from steam tables as:
c_v = 0.718 kJ/kg.K
Substituting the given values in the equation above, we get:s1 = 0.718 ln(500) - 0.287 ln(2) = 1.920 kJ/kg.Kc) State 2 is a saturated vapor state, hence, the mass-specific entropy at State 2 (s2) can be determined by using the following equation:
s2 = s_f + x * (s_g - s_f)where, s_f and s_g are the mass-specific entropy values at the saturated liquid and saturated vapor states, respectively. x is the quality of the vapor state.Substituting the given values in the equation above, we get:s2 = 1.294 + 0.831 * (7.170 - 1.294) = 6.099 kJ/kg.Kd) Using steam tables, the pressure and temperature at State 2 can be determined by using the following steps:Step 1: Determine the quality of the vapor state using the following expression:x = (h - h_f) / (h_g - h_f)where, h_f and h_g are the specific enthalpies at the saturated liquid and saturated vapor states, respectively.
Substituting the given values, we get:x = (3270.4 - 191.81) / (2675.5 - 191.81) = 0.831Step 2: Using the quality determined in Step 1, determine the specific enthalpy at State 2 using the following expression:h = h_f + x * (h_g - h_f)Substituting the given values, we get:h = 191.81 + 0.831 * (2675.5 - 191.81) = 3270.4 kJ/kgStep 3: Using the specific enthalpy determined in Step 2, determine the pressure and temperature at State 2 from steam tables.Pressure at state 2:P2 = 1.889 MPaTemperature at state 2:T2 = 228.49°C
Therefore, the pressure and temperature at State 2 are P2 = 1.889 MPa and T2 = 228.49°C.
Learn more about pressure :
https://brainly.com/question/30638002
#SPJ11
I want to know the structure of wind turbines and the
construction of wind farm platforms.
Please provide some useful websites for my
reference. Thank you.
NREL (www.nrel.gov), AWEA (www.awea.org), EWEA (www.ewea.org), WEICan (www.weican.ca), RenewableUK (www.renewableuk.com)
National Renewable Energy Laboratory (NREL) - The NREL website (www.nrel.gov) offers a wealth of information on wind energy, including details on wind turbine design, components, and construction. It provides access to research papers, technical reports, and publications related to wind energy systems.
American Wind Energy Association (AWEA) - AWEA's website (www.awea.org) is a valuable resource for understanding wind energy and wind turbine technology. It provides information on wind turbine components, installation practices, and guidelines for wind farm construction and operation.
European Wind Energy Association (EWEA) - The EWEA website (www.ewea.org) focuses on wind energy in Europe and offers insights into wind turbine structures, offshore wind farms, and the latest developments in wind energy technology.
Wind Energy Institute of Canada (WEICan) - WEICan's website (www.weican.ca) provides comprehensive information on wind turbine technology, including design, construction, and operation. It offers technical resources, case studies, and research findings related to wind energy.
RenewableUK - RenewableUK's website (www.renewableuk.com) is a valuable resource for wind energy information, particularly in the UK. It covers topics such as wind turbine structure, offshore wind farm construction, and industry updates.
These websites serve as reliable sources for learning about the structure of wind turbines and the construction of wind farm platforms. They provide technical information, case studies, research papers, and industry insights to enhance your understanding of wind energy systems.
To learn more about turbines click here
brainly.com/question/14903042
#SPJ11
A wind turbine consists of five main parts: the foundation, the tower, the rotor, the nacelle, and the generator. The foundation anchors the turbine to the ground or seabed. The tower supports the rotor and nacelle.
The rotor includes the blades and hub. The blades catch the wind and spin the rotor.
The nacelle houses the generator and other equipment.
The generator converts the rotational energy of the rotor into electrical energy.
The construction of wind farm platforms
The construction of a wind farm platform involves a number of steps, including:
Site selection and assessmentFoundation design and constructionTower erectionNacelle and blade installationElectrical interconnectionThe specific steps involved in the construction of a wind farm platform will vary depending on the type of foundation, the location of the wind farm, and the size of the turbines.
Useful websites
Wind Energy - The Facts: h ttp s: //w w w. wind-energy-the-facts.org/
How a Wind Turbine Works: ht t p s:// ww w. energy. gov/eere/wind/how-wind-turbine-works-text-version
Wind Turbine Parts: h t tp s:/ /w ww. airpes. com/wind-turbine-parts/
Construction of an Offshore Wind Farm: h t t p s://w ww .iberdrola. com/about-us/our-activity/offshore-wind-energy/offshore-wind-park-construction
To learn more about turbines click here
brainly.com/question/14903042
#SPJ11
At steady state, 5 kg/s of saturated water vapor at p1 = 1 bar enters a Direct Contact Heat Exchanger and mixes with 5 kg/s of liquid water entering at T2 = 25°C, p2 = 1 bar. A two-phase liquid–vapor mixture exits at p3 = 1 bar. Neglect heat transfer with the surroundings and the effects of motion and gravity. Let To = 30°C, po = 1 bar.
In a Direct Contact Heat Exchanger, 5 kg/s of saturated water vapor at 1 bar enters and mixes with 5 kg/s of liquid water at 25°C and 1 bar.
The mixture exits as a two-phase liquid vapor at 1 bar. The system operates at a steady state, neglecting heat transfer with the surroundings and the effects of motion and gravity. The initial conditions are given as To = 30°C and po = 1 bar. In a Direct Contact Heat Exchanger, the heat exchange occurs through direct contact between the hot vapor and the cold liquid, resulting in a two-phase liquid-vapor mixture. In this scenario, 5 kg/s of saturated water vapor at 1 bar is mixed with 5 kg/s of liquid water at 25°C and 1 bar. The specific conditions of the exit state (p3, T3) are not provided. To analyze the system, thermodynamic properties, and phase equilibrium relationships need to be considered. Without this information, it is not possible to determine the exact state of the two-phase mixture at the exit. The specific enthalpy and quality (vapor fraction) of the mixture would be necessary to assess the heat exchange and the final state of the system. In this summary, it is important to note that without additional information or assumptions about the system, it is challenging to provide a detailed analysis of the Direct Contact Heat Exchanger in this scenario.
Learn more about Direct Contact Heat Exchangers here:
https://brainly.com/question/13048103
#SPJ11
What is the index of refraction of a certain medium if the
velocity of propagation of a radio wave in this medium is
1.527x10^8 m/s?
a. 0.509
b. 0.631
c. 0.713
d. 1.965
The index of refraction of the medium is approximately 1.965
The index of refraction (n) of a medium can be calculated using the formula:
n = c / v
Where c is the speed of light in a vacuum and v is the velocity of propagation of the wave in the medium.
Given that the velocity of propagation of the radio wave in the medium is 1.527x10^8 m/s, and the speed of light in a vacuum is approximately 3x10^8 m/s, we can calculate the index of refraction:
n = (3x10^8 m/s) / (1.527x10^8 m/s)
Simplifying the expression, we get:
n ≈ 1.9647
Rounding to three decimal places, the index of refraction of the medium is approximately:
d. 1.965
Therefore, option d, 1.965, is the correct answer.
To know more about index of refraction, visit:
https://brainly.com/question/23750645
#SPJ11
(a) A solid conical wooden cone (s=0.92), can just float upright with apex down. Denote the dimensions of the cone as R for its radius and H for its height. Determine the apex angle in degrees so that it can just float upright in water. (b) A solid right circular cylinder (s=0.82) is placed in oil(s=0.90). Can it float upright? Show calculations. The radius is R and the height is H. If it cannot float upright, determine the reduced height such that it can just float upright.
Given Data:S = 0.82 (Density of Solid)S₀ = 0.90 (Density of Oil)R (Radius)H (Height)Let us consider the case when the cylinder is fully submerged in oil. Hence, the buoyant force on the cylinder is equal to the weight of the oil displaced by the cylinder.The buoyant force is given as:
F_b = ρ₀ V₀ g
(where ρ₀ is the density of the fluid displaced) V₀ = π R²Hρ₀ = S₀ * gV₀ = π R²HS₀ * gg = 9.8 m/s²
Therefore, the buoyant force is F_b = S₀ π R²H * 9.8
The weight of the cylinder isW = S π R²H * 9.8
For the cylinder to float upright,F_b ≥ W.
Therefore, we get,S₀ π R²H * 9.8 ≥ S π R²H * 9.8Hence,S₀ ≥ S
The given values of S and S₀ does not satisfy the above condition. Hence, the cylinder will not float upright.Now, let us find the reduced height such that the cylinder can just float upright. Let the reduced height be h.
We have,S₀ π R²h * 9.8
= S π R²H * 9.8h
= H * S/S₀h
= 1.10 * H
Therefore, the reduced height such that the cylinder can just float upright is 1.10H.
To know more about buoyant force visit:
brainly.com/question/20165763
#SPJ4
100 (s+1) / s^2+110s+1000
A) Find the factors of Bode stander transfer function?
B) For each factor find the: magnitude, phase, and slope?
A) The factors of Bode standard transfer function are (s + 1), (s + p1), and (s + p2). B) Its magnitude, phase and slope are given by: Magnitude: 20 log |1 / (s + p2), Phase: -arg (s + p2), Slope: -20 dB/decade.
The given transfer function is:
G(s) = 100(s + 1) / (s^2 + 110s + 1000)
A) Factors of Bode standard transfer function:
The given transfer function G(s) can be written in terms of poles and zeros as follows:
G(s) = K(s + z) / [(s + p1) (s + p2)]
where,
K = 100z = -1p1,
p2 are the poles of the transfer function
Hence, the factors of Bode standard transfer function are (s + 1), (s + p1), and (s + p2).
B) Magnitude, phase and slope for each factor:
Factor 1: s + 1
This factor is a zero of the transfer function.
Its magnitude, phase and slope are given by:
Magnitude: 20 log |(s + 1)|
Phase: arg (s + 1)
Slope: +20 dB/decade
Factor 2: s + p1
This factor is a pole of the transfer function. Its magnitude, phase and slope are given by:
Magnitude: 20 log |1 / (s + p1)|
Phase: -arg (s + p1)
Slope: -20 dB/decade
Factor 3: s + p2
This factor is also a pole of the transfer function.
Its magnitude, phase and slope are given by:
Magnitude: 20 log |1 / (s + p2)|
Phase: -arg (s + p2)
Slope: -20 dB/decade
Note: Magnitude is in dB, phase is in degrees, and slope is in dB/decade.
To know more about transfer function visit:
https://brainly.com/question/33304977
#SPJ11
a gasoline engine is at a location where the ttemperature measured to be 15.5C and produce 311kW at 5800 rpm while consuming 0,0184 kg/s of fuel. during operation data shows that it is mechanical energy loss is 18%, the actual volume of air going into each cylinder is 80% (the volumetric efficiency has a negligible variation), and the actual fuel-to-air ratio is 0.065. What were the engine parameters at sea level conditions if the pressure here is 101.0kPa and the temperature here is 18 C hotter than that of the elevated condition? Determine at sea-level conditions the Brake Power in kW. Use four (4) decimal places in your solution and answer.
At sea-level conditions, the Brake Power of the engine is 0.958 kW.
The parameters of the engine at the sea level conditions are: Pressure = 101.0 kPa, Temperature = 15.5 + 18 = 33.5 CFirst, we need to calculate the mass flow rate of air, ma:ma = mf / φma = 0.0184 / 0.065ma = 0.2831 kg/sWe can now determine the mass of fuel, mf, as follows: BP = mf x LHV x ηBP = (0.0184 x 43.107 x 0.82) / 1000BP = 0.0006446 kW or 0.6446 WBP = 0.6446 x 1000 = 644.6 WBP = 0.6446 kW
From the RPM, we can determine the engine displacement, Vd, as follows:Vd = (311 / (2 x π x 5800 / 60)) x (60 / 4) x 0.2831Vd = 0.001318 m3From the volumetric efficiency, we can determine the mass of air, ma, that would enter a cylinder at atmospheric pressure and temperature for every revolution (n = 1):ma = ρ x Vd x N x nma = 1.184 x 0.001318 x 5800 / 60 x 1ma = 0.0168 kgWe can then determine the volume of air, Va, that enters a cylinder at atmospheric pressure and temperature for every revolution (n = 1):Va = ma / ρaVa = 0.0168 / 1.184Va = 0.01416 m3We can now determine the power, Pe, that is delivered to the engine:P = BP / ηP = 0.6446 / 0.82P = 0.7859 kWPe = P / (1 - 0.18)Pe = 0.958 kWPe = 958 W
Finally, we can determine the Brake Mean Effective Pressure, bmep, using the following formula:bmep = Pe / (Va x N x n)bmep = 958 / (0.01416 x 5800 / 60 x 1)bmep = 763.3 kPa or 0.7633 MPa
Therefore, at sea-level conditions, the Brake Power of the engine is 0.958 kW.
To know more about Brake Power visit:
brainly.com/question/15709630
#SPJ11
A vertical, irregularly shaped plate is submerged in water. The table shows measurements of its width, taken at the indicated depths. Depth, x 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Plate width, w(x) 0 0.8 1.7 2.4 2.9 3.3 3.6 (a) 2 Approximate the force of water against the plate, F = pg|xw(x) dx area of cross section using Simpson's 1/3rd Rule. Given p=1000kg/m³ and g = 9.8 m/s². (5 marks) (b) Approximate the force of water against the plate, F = pg] xw(x) dx area of cross = P8|3 2 section using Simpson's 3/8th Rule correct to 2 decimal places. Given p=1000kg/m³ and g = 9.8m/s².
The force of water applied against the plate using Simpson's 1/3rd Rule is 21015.6 N (approx) and the force of water against the plate using Simpson's 3/8th Rule is 19524.6 N (approx).
Given, Depth, x 2.0 2.5 3.0 3.5 4.0 4.5 5.0Plate width, w(x) 0 0.8 1.7 2.4 2.9 3.3 3.6Here, we have to find the force of water against the plate. We are given two methods for the calculation of this force.
The first method is using Simpson's 1/3rd Rule. Let's use this method.
Using Simpson's 1/3rd RuleWe have, p
= 1000 kg/m³ and g = 9.8 m/s².Let's calculate h and find w(x) for the values of x (given in the table).The value of h is,
h = (5 - 2)/2 = 1.5.From the given table, w(2)
= 0, w(2.5) = 0.8, w(3)
= 1.7, w(3.5) = 2.4,
w(4) = 2.9, w(4.5) = 3.3
and w(5) = 3.6.
Further, we know that the area of the cross-section is given as,
A = (w1 + 4w2 + 2w3 + 4w4 + 2w5 + 4w6 + w7) × (h/3)A
= (0 + 4(0.8) + 2(1.7) + 4(2.4) + 2(2.9) + 4(3.3) + 3.6) × (1.5/3)A
= 5.08 m²
Now, let's calculate the force of water against the plate.
Force, F = pg∫|xw(x) dx area of cross-sectionF
= (1000 kg/m³) × (9.8 m/s²) × ∫[2,5]|xw(x) dx A
where, w(x) is the plate width at depth x.
Now, using Simpson's 1/3rd rule, we can write,
F = (1000 kg/m³) × (9.8 m/s²) × (1.5/3) × (0 + 4(0.8 × 2) + 2(1.7 + 2.4 + 2.9 + 3.3) + 3.6 × 2)
F = 21015.6 N
Therefore, the force of water against the plate is 21015.6 N (approx).Now, let's use Simpson's 3/8th Rule to find the force of water against the plate.
where, w(x) is the plate width at depth x
.Now, using Simpson's 3/8th rule, we can write,
F = (1000 kg/m³) × (9.8 m/s²) × (3/8) × (0 + 3(0.8 × 2 + 1.7 + 0.8 × 2.5) + 2(1.7 + 2.4 + 0.8 × 3 + 2.9) + 3(2.4 + 3.3 + 3.6 + 3.3 + 2.4) + 3.6)
F = 19524.6 N
Therefore, the force of water against the plate using Simpson's 3/8th Rule is 19524.6 N (approx).
Thus, the force of water against the plate using Simpson's 1/3rd Rule is 21015.6 N (approx) and the force of water against the plate using Simpson's 3/8th Rule is 19524.6 N (approx).
To know more about applied visit
https://brainly.com/question/33140251
#SPJ11