When the clock frequency is 16 MHz, the reload value that will give a SysTick timer interval of 1 ms is 15,999.
When a clock frequency of 16 MHz is selected as the clock timer, what is the Reload value required to obtain a 1 ms SysTick timer interval?
The SysTick timer is commonly used to maintain real-time systems. The SysTick timer is a 24-bit down-counter that, when it reaches zero, produces an interrupt.
The timebase for the SysTick is typically the CPU clock, and the SysTick interval is determined by a reload value stored in a system register.
The SysTick interval is calculated using the formula:
SysTick interval = (Reload value + 1) / System clock frequency
The formula to compute the reload value is:
Reload value = SysTick interval × System clock frequency - 1 = (1 × 16 × 10^6) - 1 = 15999
Since the clock frequency is 16 MHz, the reload value that will give a SysTick timer interval of 1 ms is 15,999.
Learn more about frequency at: https://brainly.com/question/254161
#SPJ11
An electrical power meter can measure power over the range from 0.1 W to 100 kW. What is the dynamic range of the meter? A. 50 dB B. 60 dB C. 100 dB D. 120 dB A pressure gauge is fitted in a thin film processing chamber and reading a value of 6.54 bar. Considering that the atmospheric pressure surrounding the chamber is 1.013 bar, what is the gauge pressure? A. 7.55 bar B. 5.53 bar C. 6.54 bar D. 1.013 bar A voltage to frequency converter has an input range of 0-10 V and an output range of 100 kHz to 4 MHz. What is the output span? A. 3.9 MHZ B. 10 V C. 100 kHz D. 3 MHz
The dynamic range of the power meter is 60 dB, the gauge pressure is 5.527 bar, and the output span of the voltage to frequency converter is 3.9 MHz.
What is the dynamic range of the power meter, the gauge pressure, and the output span of the voltage to frequency converter?The dynamic range of a power meter is the ratio between the maximum and minimum measurable power levels. In this case, the dynamic range can be calculated using the formula:
Dynamic Range (in dB) = 10 * log10 (Maximum Power / Minimum Power)
For the given power meter, the maximum power is 100 kW and the minimum power is 0.1 W. Plugging these values into the formula:
Dynamic Range (in dB) = 10 * log10 (100,000 / 0.1) = 10 * log10 (1,000,000) = 10 * 6 = 60 dB
Therefore, the dynamic range of the power meter is 60 dB.
The gauge pressure is the pressure measured by the pressure gauge relative to the atmospheric pressure. To calculate the gauge pressure, we subtract the atmospheric pressure from the reading of the pressure gauge.
Gauge Pressure = Reading - Atmospheric Pressure = 6.54 bar - 1.013 bar = 5.527 bar
Therefore, the gauge pressure is 5.527 bar.
The output span of a voltage to frequency converter is the difference between the maximum and minimum output frequencies. In this case, the output range is from 100 kHz to 4 MHz.
Output Span = Maximum Output Frequency - Minimum Output Frequency = 4 MHz - 100 kHz = 3.9 MHz
Therefore, the output span is 3.9 MHz.
Learn more about dynamic range
brainly.com/question/31715117
#SPJ11
State the difference between SOP and POS. A. SOP uses maxterms POS uses minterms B. POS uses maxterms SOP uses maxterms C. POSusesminterms SOPusesminterms D. POS uses maxterms SOP uses minterms
The correct option is D, POS uses maxterms SOP uses minterms. The terms SOP and POS relate to the two standard methods of representing Boolean expressions.
In SOP (Sum of Products), the output of a logic circuit can be defined as the sum of one or more products in which each product consists of a combination of inputs, and the output is either true or false.What is POS?In POS (Product of Sums), the output of a logic circuit can be defined as the product of one or more sums in which each sum consists of a combination of inputs, and the output is either true or false.
Difference between SOP and POS: POS uses maxterms, whereas SOP uses minterms. The two expressions for each circuit are the complement of one another. Hence option D is correct.
To learn more about "Boolean Expressions" visit: https://brainly.com/question/26041371
#SPJ11
bus The frictional resistance for fluids in motion varies O slightly with temperature for laminar flow and considerably with temperature for turbulent flow O considerably with temperature for laminar flow and slightly with temperature for turbulent flow O considerably with temperature for both laminar and burbulent flows slightly with temperature for both laminar and turbulent flows
The frictional resistance for fluids in motion varies slightly with temperature for laminar flow and considerably with temperature for turbulent flow is correct.
The frictional resistance for fluids in motion varies slightly with temperature for laminar flow and considerably with temperature for turbulent flow. In laminar flow, where the fluid moves in smooth, parallel layers, the frictional resistance is primarily determined by the viscosity of the fluid. The viscosity of most fluids changes only slightly with temperature, resulting in a minor variation in frictional resistance. On the other hand, turbulent flow is characterized by chaotic, swirling motion with eddies and vortices. The frictional resistance in turbulent flow is influenced by factors such as fluid viscosity, velocity, and turbulence intensity. The viscosity of fluids typically changes significantly with temperature, leading to considerable variations in the frictional resistance for turbulent flow. It's worth noting that other factors, such as surface roughness and flow conditions, can also affect the frictional resistance in fluid flow.
Learn more about the frictional resistance here:
brainly.com/question/2963008
#SPJ11
Design for flexure a beam 14 ft in length, having a uniformly distributed dead load of 3 kip per ft, a uniformly distributed live load of 4 kip per ft and a concentrated dead load of 12 kips at its center point.
Design for flexure a beam 14 ft in length, having a uniformly distributed dead load of 3 kip per ft, a uniformly distributed live load of 4 kip per ft, and a concentrated dead load of 12 kips at its center point.
The calculation of the moment capacity of the beam using the AISC-ASD code is critical in the design of a beam under flexure. In a situation where a beam is loaded, it develops a moment that is equivalent to the load times the distance from the point of reference. The calculation of this moment is known as the moment capacity.
The beam can be designed using the following steps:
i. Determine the total load that is acting on the beam. This is computed as a summation of the uniformly distributed dead load, the uniformly distributed live load, and the concentrated dead load.
ii. Compute the moment capacity of the beam. This calculation involves computing the maximum bending moment acting on the beam using the beam's length and the load distribution. The design of a beam should consider the maximum moment and the shear stress.
iii. Calculate the maximum allowable stress and the beam's flexural stress, which should be less than the maximum allowable stress. If the calculated stress exceeds the allowable stress, the design must be adjusted, either by increasing the beam's depth or the width.
The design of the beam can be done using a beam design software such as Microsoft Excel or by using the standard formulas. The design process involves the determination of the maximum moment and the maximum shear stress acting on the beam. Once these two quantities are known, it is easy to calculate the maximum allowable stress and the actual stress. The actual stress should be less than the maximum allowable stress.
To know more about Microsoft Excel refer to:
https://brainly.com/question/32047461
#SPJ11
Task: It is required to convolve two continuous time exponential signals given by the user. The signals should have the following characteristics Increasing exponential or decreasing exponential Left-sided or right-sided signal. - Boundary points of the signals are integers. You are required to write a code in Matlab to: 1. Take required parameters, of the two signals, as input from user. 2. Convolve the two signals using symbolic toolbox. 3. Display the mathematical expression of the output of the convolution process. 4. Plot the input and output signals.
Convolution of two exponential signals in MATLAB Exponential signals are signals in which the value of the signal grows or decays exponentially with time.
They can either be increasing or decreasing exponential signals. In this task, we are required to convolve two continuous time exponential signals given by the user. The signals should have the following characteristics: Increasing exponential or decreasing exponential Left-sided or right-sided signal Boundary points of the signals are integers.
The task requires us to write a code in MATLAB that will take required parameters of the two signals as input from the user. Then, we will convolve the two signals using symbolic toolbox and display the mathematical expression of the output of the convolution process. Finally, we will plot the input and output signals.
The following code can be used to convolve two exponential signals:%% Take input parameters from userx1 = input('Enter the first signal: ');t1 = input('Enter the time vector of first signal: ');x2 = input('Enter the second signal: ');t2 = input('Enter the time vector of second signal: ');%%.
To know more about exponential visit:
https://brainly.com/question/29160729
#SPJ11
What is the Nyquist sampling rate for this signal:
sinc(50t)sinc(100t)
the Nyquist sampling rate for this signal would be 200 samples per second (Hz), as it is greater than 100 Hz.
The Nyquist sampling rate is determined by the highest frequency component in the signal. In this case, the signal is given as
sinc(50t) x sinc(100t). To find the Nyquist sampling rate, we need to determine the highest frequency present in the signal.
The sinc function has a main lobe width of 2π, which means that its bandwidth is approximately 1/π.
For sinc(50t), the highest frequency component is 50 cycles per second (Hz).
For sinc(100t), the highest frequency component is 100 cycles per second (Hz).
To ensure accurate reconstruction of the signal, the sampling rate must be at least twice the highest frequency component. Therefore, the Nyquist sampling rate for this signal would be 200 samples per second (Hz), as it is greater than 100 Hz.
Learn more about the Nyquist sampling sampling rates here:
brainly.com/question/31735568
#SPJ11
In an orthogonal cutting operation in tuning, the cutting force and thrust force have been measured to be 300 lb and 250 lb, respectively. The rake angle = 10°, width of cut = 0.200 in, the feed is 0.015in/rev, and chip thickness after separation is 0.0375. Determine the shear strength of the work material.
The shear strength of the work material is equal to 40,000 lb/in^2.
Explanation:
To determine the shear strength of the work material in an orthogonal cutting operation, we can use the equation:
Shear Strength = Cutting Force / (Width of Cut * Chip Thickness)
Given the values provided:
Cutting Force = 300 lb
Width of Cut = 0.200 in
Chip Thickness = 0.0375 in
Plugging these values into the equation, we get:
Shear Strength = 300 lb / (0.200 in * 0.0375 in)
Simplifying the calculation, we have:
Shear Strength = 300 lb / (0.0075 in^2)
Therefore, the shear strength of the work material is equal to 40,000 lb/in^2.
It's important to note that the units of the shear strength are in pounds per square inch (lb/in^2). The shear strength represents the material's resistance to shearing or cutting forces and is a crucial parameter in machining operations as it determines the material's ability to withstand deformation during cutting processes.
Know more about Shear Strength here:
https://brainly.com/question/31746102
#SPJ11
An HVAC system must supply 250 CFM of air with a temperature of 60°F and relative humidity of 40%. The system receives return air with a temperature of 70°F and relative humidty of 60% which it mixes with outside air at 85°F and 80% relative humidity with a ratio of 75% return air and 25% outside air on a mass basis. The outside air and return air are first mixed. The mixure is then cooled and dehumidified before finally reheating to the desired exit condition. A) Sketch the system hardware
B) Sketch the process on a psychometric diagram
C) Find the volumetric flow rate of the return air in ft3/min
D) Find the volumetric flow rate for the outside air in ft3/min
E) Find the mass flow rate of water condensate removal in lbm/min
F) Find the net rate of heat transfer for the system in Btu/min
Please show all work. Thank you.
A) The sketch of the system hardware is given below.B) The process on a psychometric diagram is given below:C).
The volumetric flow rate of the return air in ft3/min is calculated as follows:Given data are: Air supply capacity Q = 250 CFM.
Ratio of air (return air to outside air) = 75:25; Volumetric flow rate of the mixture of outside and return air = 250 ft3/min (As it supplies at a flow rate of 250 CFM)By using the formula for mass balance, we can write it as below;Where Q1 is the volumetric flow rate of the return air.
The volumetric flow rate of the outside air, and Q is the volumetric flow rate of the mixture. Q1/Q2 = (100-R)/R; R = 75 (Ratio of the flow rate of the return air to the outside air) Q = Q1 + Q2; Q2 = Q - Q1By using these formulas.
we can solve for the flow rate of the return air Q1Q1 = (100/75) × Q2Q1 = (100/75) × (Q - Q1)Q1 = 0.57Q ft3/minQ1 = 0.57 × 250 ft3/minQ1 = 142.5 ft3/min, the volumetric flow rate of the return air in ft3/min is 142.5 ft3/min.D) The volumetric flow rate for the outside air in ft3/min is calculated as follows.
To know more about psychometric visit:
https://brainly.com/question/16737798
#SPJ11
What wiring would you not expect to find on a single line diagram? ?1. branch circuit wiring to a load 2. feeder to distribution panel 3.service power from utility 4.feeder to sub-panel1.
The wiring that you would not expect to find on a single line diagram is:
Branch circuit wiring to a load
A single line diagram represents the electrical distribution system at a higher level, showing the major components and connections. It typically includes the main components such as generators, transformers, switchgear, and major distribution panels. Branch circuit wiring to individual loads, such as outlets or appliances, is not typically shown on a single line diagram. Instead, it focuses on the main power flow and distribution paths.
Feeder to distribution panel, service power from the utility, and feeder to sub-panel are all components and connections that would be expected to be shown on a single line diagram as they represent the main elements of the electrical distribution system.
Know more about Branch circuit here:
https://brainly.com/question/31889919
#SPJ11
Analyse the circuit below given ECC=10V, R1=82kΩ, R2=22kΩ,
R3=5.6kΩ, R4=1.5kΩ and β = 100. Determine ETH, IB, VCEq, VB, and
VE.
ETH = 1.85 V, IB = 18.5 μA, VCEq = 8.15 V, VB = 1.85 V, and VE = 1.05 V.
In this circuit, the given values for ECC (Emitter Current Control voltage) and resistors (R1, R2, R3, R4) along with the transistor's β value (current gain) are used to determine various parameters.
To find ETH (Emitter to Base voltage), we use the voltage divider rule:
ETH = ECC * (R2 / (R1 + R2))
ETH = 10 * (22kΩ / (82kΩ + 22kΩ))
ETH ≈ 1.85 V
To calculate IB (Base Current), we divide ETH by the resistance R3:
IB = ETH / R3
IB ≈ 1.85 V / 5.6kΩ
IB ≈ 18.5 μA
To determine VCEq (Collector to Emitter voltage), we apply Kirchhoff's voltage law:
VCEq = ECC - IB * R4
VCEq = 10V - (18.5μA * 1.5kΩ)
VCEq ≈ 8.15 V
To find VB (Base voltage), we use the voltage divider rule:
VB = ETH * (R1 / (R1 + R2))
VB = 1.85 V * (82kΩ / (82kΩ + 22kΩ))
VB ≈ 1.85 V
Finally, to calculate VE (Emitter voltage), we apply Kirchhoff's voltage law:
VE = VB - IB * R3
VE = 1.85 V - (18.5μA * 5.6kΩ)
VE ≈ 1.05 V
Learn more about resistors
brainly.com/question/30672175
#SPJ11
Prove that in any undirected graph, the sum of the degrees of all the vertices is even.
The sum of the degrees of all vertices, which is equal to 2m, is even
To prove that the sum of the degrees of all vertices in any undirected graph is even, we can use the Handshaking Lemma. The Handshaking Lemma states that the sum of the degrees of all vertices in a graph is equal to twice the number of edges.
Let's consider an undirected graph with n vertices and m edges. Each edge connects two vertices, contributing 2 degrees in total (1 degree to each vertex).
Therefore, the sum of the degrees is 2m.
Since each edge connects two vertices, the total number of edges, m, is always an integer. Thus, 2m is an even number, as any multiple of 2 is even.
Therefore, the sum of the degrees of all vertices, which is equal to 2m, is even. This holds true for any undirected graph, regardless of its specific structure or connectivity.
Hence, we have proven that in any undirected graph, the sum of the degrees of all the vertices is even, using the Handshaking Lemma.
For more such questions on sum,click on
https://brainly.com/question/30221799
#SPJ8
According to the Clausius' theorem, the cyclic integral of for a reversible cycle is zero. OdW/dT OdH/dT O dE/dT OdQ/dT
According to Clausius' theorem, the cyclic integral of the differential of heat transfer (dQ) divided by the absolute temperature (T) is zero for a reversible cycle.
In other words, when considering a complete cycle of a reversible process, the sum of the infinitesimal amounts of heat transfer divided by the corresponding absolute temperatures throughout the cycle is equal to zero.
Mathematically, this can be expressed as:
∮ (dQ / T) = 0
This theorem highlights the concept of entropy and the irreversibility of certain processes. For a reversible cycle, the heat transfer can be completely converted into work, and no net transfer of entropy occurs. As a result, the cyclic integral of dQ/T is zero, indicating that the overall heat transfer in the cycle is balanced by the temperature-dependent factor.
Therefore, the correct option is:
[tex]OdQ/dT.[/tex]
Learn more about Clausius' theorem here:
brainly.com/question/30853813
#SPJ11
r. n 1 bar, 350 K with a mass flow rate of 1 kg/s and exits at 4 bar. The pressor operating at steady state at isentropic compressor efficiency is 82%. Determine the power input, in kW, and the rate of entropy production, in kW/K, using the ideal gas model with data from Table A-22. 6.102 Refrigerant 134a enters a compressor operating at steady state as saturated vapor at -6.7°C and exits at a pressure of 0.8 MPa. There is no significant heat transfer with the surroundings, and kinetic and potential energy effects can be ignored. a. Determine the minimum theoretical work input required, in kJ per kg of refrigerant flowing through the compressor, and the cor- responding exit temperature, in °C. b. If the refrigerant exits at a temperature of 49°C, determine the 1 1 isentropic compressor efficiency. 6.103 Air at 1.3 bar, 423 K and a velocity of 40 m/s enters a nozzle operating at steady state and expands adiabatically to the exit, where the pressure is 0.85 bar and velocity is 307 m/s. For air modeled as an with b = 1.4, determine for the nozzle (a) the temperature at Giancy
The minimum theoretical work input required, in kJ per kg of refrigerant flowing through the compressor, is -119.55 kJ/kg (work input), and the corresponding exit temperature is 45.9°C, in °C.
6.102 Refrigerant 134a enters a compressor operating at steady state as saturated vapor at -6.7°C and exits at a pressure of 0.8 MPa. There is no significant heat transfer with the surroundings, and kinetic and potential energy effects can be ignored.
a. Determine the minimum theoretical work input required, in kJ per kg of refrigerant flowing through the compressor, and the corresponding exit temperature, in °C.
The given conditions are:
Inlet conditions:
Temperature, T1 = -6.7°C
Refrigerant exits as a compressed vapor at pressure, P2 = 0.8 MPa
Assuming compressor to be an adiabatic compressor, that is Q = 0 i.e., there is no heat transfer.
Also, there are no kinetic or potential energy effects and hence,
h1 = h2s, where h2s is the specific enthalpy of refrigerant at state 2s.
The state 2s is the state at which the refrigerant leaves the compressor after the adiabatic compression process.
Therefore, the process of compression is IsentropicCompression, i.e.,
s1 = s2s.
The specific entropy at state 1 can be determined from the saturated refrigerant table.
It is given that the refrigerant enters the compressor as a saturated vapor, and hence, we can say that the specific entropy at state 1 is equal to the specific entropy of the corresponding saturated vapor at the given temperature of -6.7°C.
From the saturated table for Refrigerant 134a:
At T = -6.7°C, saturated vapor has specific entropy, s1 = 1.697 kJ/kg·K
The specific enthalpy at state 1 can be determined from the saturated refrigerant table.
It is given that the refrigerant enters the compressor as a saturated vapor, and hence, we can say that the specific enthalpy at state 1 is equal to the specific enthalpy of the corresponding saturated vapor at the given temperature of -6.7°C.
From the saturated table for Refrigerant 134a:
At T = -6.7°C, saturated vapor has specific enthalpy, h1 = 257.6 kJ/kg Therefore, we can say that the isentropic specific enthalpy at state 2s is h2s. Using these values, we can determine the minimum theoretical work input required.
The isentropic specific enthalpy can be determined from the table A-22. It is given that the refrigerant exits the compressor at a pressure of 0.8 MPa.
Hence, we can say that the specific enthalpy at state 2s is h2s = 377.15 kJ/kg.
Work input required:
W = h1 - h2s= 257.6 - 377.15=-119.55 kJ/kg
The negative sign signifies that the work is input, i.e., work is required for the compression process.
Corresponding exit temperature:
The corresponding exit temperature can be determined from the refrigerant table using the specific enthalpy at state 2s.
From the refrigerant table for Refrigerant 134a:
At a pressure of 0.8 MPa, specific enthalpy, h2s = 377.15 kJ/kg
The corresponding exit temperature, T2s = 45.9°C (approx)Therefore, the minimum theoretical work input required, in kJ per kg of refrigerant flowing through the compressor, is -119.55 kJ/kg (work input), and the corresponding exit temperature is 45.9°C, in °C.
To know more about minimum theoretical work visit:
https://brainly.com/question/32673403
#SPJ11
QUESTION 13 Which of the followings is true? O A. For a full inductor, at time t=0 when it is switched on, its through current will likely drop to half its value. O B. For a full inductor, at time t=0 when it is switched on, its through current will likely drop to quarter its value. O C. For an empty inductor, at time t=0 when it is switched on, its through current will be close to zero. O D. For a full capacitor, at time t=0 when it is switched on, its across voltage will be close to zero.
The correct statement is:C. For an empty inductor, at time t=0 when it is switched on, its through current will be close to zero.
When an inductor is initially empty and then switched on at time t=0, the current through the inductor will not change instantaneously. Instead, it will start from zero and gradually increase over time. This behavior is due to the inductor opposing changes in current. Therefore, the through current of an empty inductor at t=0 will be close to zero.The other options (A, B, and D) are incorrect because they describe different behaviors that do not accurately reflect the characteristics of an inductor when it is switched on.
Learn more about inductor here:
https://brainly.com/question/31503384
#SPJ11
1) State the kelvin's law for economic section of a
feeder conductor . Mention the reasons for preferring the Kelvin's
law.
2) Why transformer is called as heart of power
distribution system ? Explain
Kelvin's law states that the annual cost of energy loss in a feeder conductor is equal to the annual fixed cost of the conductor, and it is preferred for determining the most economical conductor size.
Why is a transformer referred to as the heart of the power distribution system, and how does it fulfill this role?Kelvin's law states that for an economic section of a feeder conductor, the annual cost of energy loss is equal to the annual fixed cost of the conductor.
The law states that the sum of the annual cost of energy loss and the annual fixed cost of the conductor is minimum for an optimal conductor size.
Reasons for preferring Kelvin's law:
It helps in determining the most economical size of the feeder conductor by balancing the cost of energy loss and the cost of the conductor itself. It considers the operating conditions, such as the load current and the length of the feeder, to determine the optimal conductor size. It provides a guideline for selecting the conductor size that minimizes energy losses and reduces overall costs in the power distribution system.A transformer is called the "heart" of a power distribution system due to the following reasons:
Role in voltage transformation: Transformers are responsible for stepping up or stepping down the voltage levels in the power distribution system. Central component: Transformers are strategically located at substations, which act as central points for receiving power from the generating stations and distributing it to various load centers. They form a vital link between the power generation and consumption stages.Ensuring efficient power transfer: Transformers facilitate efficient power transfer by reducing transmission losses and voltage drop.
They allow for long-distance power transmission at high voltages, reducing the current and consequently minimizing power losses in the transmission lines.Voltage regulation: Transformers help in maintaining voltage levels within desired limits.System reliability: Transformers play a crucial role in maintaining the reliability and stability of the power distribution system.
Learn more about determining
brainly.com/question/29898039
#SPJ11
A reheat-regenerative Rankine cycle uses steam at 8.4 MPa and 560°C entering the high-pressure turbine. The cycle includes one steam-extraction stage for regenerative feedwater heating, the remainder at this point being reheated to 540°C. The condenser temperature is 35°C. Determine (a) the T-s diagram for the cycle; (b) optimum extraction pressure; (c) fraction of steam extracted; (d) turbine work in kJ/kg; (e) pump work in kJ/kg; (f) overall thermal efficiency.
The T-s diagram for the cycle consists of the following stages: 1-2: Isentropic expansion in the high-pressure turbine from 8.4 MPa and 560°C to the reheater temperature of 540°C. 2-3: Constant pressure heat addition in the reheater. 3-4: Isentropic expansion in the low-pressure turbine. 4-5: Constant pressure heat rejection in the condenser. 5-6: Isentropic compression in the feedwater pump.
The optimum extraction pressure is determined by finding the pressure at which the extracted steam temperature matches the feedwater temperature before entering the pump.
The fraction of steam extracted is calculated by dividing the enthalpy difference between extraction and turbine outlet by the enthalpy difference between the initial and final turbine stages.
The turbine work is the difference in enthalpy between the inlet and outlet of the turbine.
The pump work is the difference in enthalpy between the outlet and inlet of the pump.
The overall thermal efficiency is determined by dividing the net work output (turbine work minus pump work) by the heat input to the cycle (enthalpy difference between the initial and final turbine stages).
Learn more about high-pressure turbine here:
https://brainly.com/question/32316959
#SPJ11
A 240 V dc shunt motor has an armature resistance of 0.05 Ohms. When the motor is UNLOADED and connected to its supply, the armature current is 20 A, the field current is 12 A, and the speed is 1200 rpm. Now, a load is applied to the shaft, and the armature current increases to 300 A and the speed drops to 1150 rpm. The motor drives a mechanical load, which requires a torque proportional to speed square. . The speed is to be reduced to 900 rpm by inserting a resistance in series with the armature. The field current is kept the same. Determine the value of the added series resistance. . Determine the speed of the system if a resistance of 0.5 Ohms is inserted in series with the armature.
The value of the added series resistance is 0.45 Ohms, and the speed of the system if a resistance of 0.5 Ohms is inserted in series with the armature is 942 rpm.
The armature current before and after the load is applied can be expressed as follows:
Before: I1 = 20 A
After: I2 = 300 A
Therefore, the resistance of the motor, which is armature resistance, can be expressed as follows:R = (240/20) = 12 Ω
The back EMF before and after the load is applied can be expressed as follows:
Before: E1 = V − I1R = 240 − (20 × 0.05) = 239 V
After: E2 = V − I2R - (12 × 0.05) = 240 − (300 × 0.05) − (12 × 0.05) = 225 V
The speed of the motor is proportional to the back EMF.
N1/N2 = E1/E2 = 239/225
N2 = (225/239) × 1200 = 1128 rpm
Let R be the added series resistance in the armature, and let N be the new speed.
The current in the motor can be calculated as follows:If the motor current is I, then the armature voltage is (240 - I(R + 0.05)).
Therefore, the following equation can be used to calculate the motor current:
I = (240 - I(R + 0.05)) / (12 + 0.05)
The speed can be calculated using the following equation:
N / 1200 = E1 / (240 - I(R + 0.05))
Substituting the values, we obtain:(N / 1200) = 239 / (240 - I(R + 0.05))1200(N / 1200) = 239(240 - I(R + 0.05))
1200N = 239(240 - I(R + 0.05))
I = 300 A and N = 900 rpm, hence:
900 = 239(240 - 300(R + 0.05))
R = (239 × 240 - 900) / (300 × 239)
R = 0.45 Ω
When a resistance of 0.5 Ohms is inserted in series with the armature, the speed of the system is calculated as follows:
I = (240 - I(R + 0.05)) / (12 + 0.05)I = (240 - 300(0.5 + 0.05)) / (12 + 0.05)I = 10 A
Using the equation:
N / 1200 = E1 / (240 - I(R + 0.05))N / 1200 = 239 / (240 - 10(0.5 + 0.05))
N / 1200 = 187.72
N = 187.72 × 1200 / 239
N = 942 rpm
Learn more about resistance at
https://brainly.com/question/32391949
#SPJ11
Find the value need to be loaded in SPBRG (Serial Port Baud Rate Generator) register to achieve the baud rate 38,400 bps in asynchronous low speed mode. The value of = 20 Hz. i) Calculate the % error in baud rate computation that may arise in Q3a. Indicate the main reason for the introduction of the error. ii) Write an embedded C program for the PIC16F877A to transfer the letter ‘HELP' serially at 9600 baud continuously. Assume XTAL = 10 MHz.
The value can be calculated using the formula SPBRG = (Fosc / (64 * BaudRate)) - 1, where Fosc is the oscillator frequency and BaudRate is the desired baud rate.
How can we calculate the value needed in the SPBRG register for a baud rate of 38,400 bps in asynchronous low-speed mode?The value needed to be loaded in the SPBRG (Serial Port Baud Rate Generator) register to achieve a baud rate of 38,400 bps in asynchronous low-speed mode can be calculated using the formula:
SPBRG = (Fosc / (64 * BaudRate)) - 1
Given that the oscillator frequency (Fosc) is 20 Hz and the desired baud rate is 38,400 bps, we can substitute these values into the formula to calculate the SPBRG value.
i) To calculate the % error in baud rate computation, we can compare the actual baud rate achieved with the desired baud rate. The main reason for the introduction of the error is the limitations in the accuracy of the oscillator frequency and the calculation formula.
ii) To write an embedded C program for the PIC16F877A to transfer the letter 'HELP' serially at 9600 baud continuously, we need to configure the UART module, set the baud rate, and transmit the data using appropriate functions or registers. The XTAL frequency of 10 MHz will be used for the calculations and configuration of the UART module.
Learn more about SPBRG
brainly.com/question/32716568
#SPJ11
In an Otto cycle, 1m^3of air enters at a pressure of 100kPa and a temperature of 18°C. The cycle has a compression ratio of 10:1 and the heat input is 760kJ. Sketch the P-v and T-s diagrams. State at least three assumptions.
CV=0.718kJ/kg K CP=1.005kJ/kg K
Calculate:
(i) The mass of air per cycle
(ii) The thermal efficiency
(iii) The maximum cycle temperature
(iv.) The net- work output
The calculations will provide the required values for the given Otto cycle
(i) m = (100 kPa × 1 m³) / (0.287 kJ/(kg·K) × 291.15 K)
(ii) η = 1 - [tex](1 / 10^{(0.405)})[/tex]))
(iii) [tex]T_{max}[/tex] = (18°C + 273.15 K) × [tex]10^{(0.405)}[/tex]
(iv) [tex]W_{net}[/tex] = 760 kJ - [tex]Q_{out}[/tex]
Assumptions:
The air behaves as an ideal gas throughout the cycle.
The combustion process is assumed to occur instantaneously.
There are no heat losses during compression and expansion.
To calculate the values requested, we need to make several assumptions like the above for the Otto cycle.
Now let's proceed with the calculations:
(i) The mass of air per cycle:
To calculate the mass of air, we can use the ideal gas law:
PV = mRT
Where:
P = pressure = 100 kPa
V = volume = 1 m³
m = mass of air
R = specific gas constant for air = 0.287 kJ/(kg·K)
T = temperature in Kelvin
Rearranging the equation to solve for m:
m = PV / RT
Convert the temperature from Celsius to Kelvin:
T = 18°C + 273.15 = 291.15 K
Substituting the values:
m = (100 kPa × 1 m³) / (0.287 kJ/(kg·K) × 291.15 K)
(ii) The thermal efficiency:
The thermal efficiency of the Otto cycle is given by:
η = 1 - (1 / [tex](compression ratio)^{(\gamma-1)}[/tex])
Where:
Compression ratio = 10:1
γ = ratio of specific heats = CP / CV = 1.005 kJ/(kg·K) / 0.718 kJ/(kg·K)
Substituting the values:
η = 1 - [tex](1 / 10^{(0.405)})[/tex]))
(iii) The maximum cycle temperature:
The maximum cycle temperature occurs at the end of the adiabatic compression process and can be calculated using the formula:
[tex]T_{max}[/tex] = T1 ×[tex](compression ratio)^{(\gamma-1)}[/tex]
Where:
T1 = initial temperature = 18°C + 273.15 K
Substituting the values:
[tex]T_{max}[/tex] = (18°C + 273.15 K) × [tex]10^{(0.405)}[/tex]
(iv) The net work output:
The net work output of the cycle can be calculated using the equation:
[tex]W_{net}[/tex] = [tex]Q_{in} - Q_{out}[/tex]
Where:
[tex]Q_{in[/tex] = heat input = 760 kJ
[tex]Q_{out }[/tex] = heat rejected = [tex]Q_{in} - W_{net}[/tex]
Substituting the values:
[tex]W_{net}[/tex] = 760 kJ - [tex]Q_{out}[/tex]
These calculations will provide the required values for the given Otto cycle.
To learn more about Otto cycle, visit:
https://brainly.com/question/13156035
#SPJ11
Design and implement a sequence generator to generate a sequence which has a 10 or more different states: 0, 11, 14, 5, 4, 15, 12, 9, 2,13, 0, 11, ... Ensure that all invalid stages of the machine clear it (set it too state zero.)
By using a finite state machine approach and adding transition paths to state zero for any invalid state, we can design a circuit that generates the desired sequence while ensuring invalid states are cleared.
How can we design and implement a sequence generator with 10 or more different states and handle invalid states?To design and implement a sequence generator with 10 or more different states, we can use a finite state machine (FSM) approach. The FSM will have states representing the desired sequence elements: 0, 11, 14, 5, 4, 15, 12, 9, 2, 13. The sequence will repeat after reaching state 13, transitioning back to state 0.
To ensure that all invalid states clear the machine and set it to state zero, we can add transition paths from any state not included in the desired sequence to state 0. This ensures that if the machine enters an invalid state, it will automatically reset to the starting state.
The implementation of the sequence generator can be done using a combinational or sequential logic circuit, such as a state register and a combinational logic block to determine the next state based on the current state. The logic circuit should have appropriate outputs to represent the desired sequence elements.
By designing the sequence generator with the specified states and including the necessary transitions to reset the machine, we can create a circuit that generates the desired sequence while handling invalid states gracefully.
Learn more about finite state machine
brainly.com/question/32268314
#SPJ11
n the following microstructures, which one possesses the lowest ductility? A.) 0.25 wt%C with fine pearlite B.)0.25 wt%C with coarse pearlite C.)0.60 wt%C with fine pearlite D.)0.60 wt%C with coarse pearlite
Ductility is the property of a material that allows it to be drawn or stretched into thin wire without breaking. Pearlitic steel is a combination of ferrite and cementite that has a pearlite microstructure. Microstructures of pearlitic steel determine the ductility of the steel.
The following microstructures, 0.25 wt%C with fine pearlite, 0.25 wt%C with coarse pearlite, 0.60 wt%C with fine pearlite, and 0.60 wt%C with coarse pearlite, are compared to determine which one possesses the lowest ductility. Out of the four microstructures given, the one with the lowest ductility is 0.60 wt%C with coarse pearlite. This is because 0.60 wt%C results in a high concentration of carbon in the steel, which increases its brittleness. Brittleness is the opposite of ductility and refers to the property of a material to crack or break instead of stretching or bending. Thus, the steel becomes more brittle as the carbon content increases beyond 0.25 wt%C. Coarse pearlite also reduces the ductility of the steel because the large cementite particles act as stress raisers, leading to the formation of cracks and reducing the overall strength of the steel. Therefore, the combination of high carbon content and coarse pearlite results in the lowest ductility compared to the other microstructures.
In contrast, the microstructure of 0.25 wt%C with fine pearlite possesses the highest ductility out of the four microstructures given. This is because 0.25 wt%C is a lower concentration of carbon in the steel, resulting in less brittleness and a higher ductility. Fine pearlite also increases the ductility of the steel because the smaller cementite particles do not act as stress raisers and are more evenly distributed throughout the ferrite. Thus, the steel is less prone to crack and has a higher overall strength. Therefore, the combination of low carbon content and fine pearlite results in the highest ductility compared to the other microstructures.
To know more about Ductility refer to:
https://brainly.com/question/4313413
#SPJ11
Abdulaziz plans to start a production facility for a new product. His cost estimations considered the following. He wil rent a small building for 5.000dhs per month for production purposes. Uties cont estimated at 500dhs per month. He will rent production equipment at a monthly cost of 4,000dhs. He estimates the material cost per und will be 15dhs, and the labor cost will be 15h per un Advertising and promotion costs estimated at 3.500dhs per month to promote for the new product Based on the above match the closest answer to the below questions Total fixed cost is If the machine maximum production capacity is 1000 units per month, what is the selling price per unit he should set to break even monthly? a. 13.000 Dhs b. 43 Dhs
Abdulaziz's cost estimations include rent, utility costs, equipment rental, material cost, labor cost, and advertising/promotion costs. The selling price per unit needed to break even is 9.50 AED.
What are Abdulaziz's cost estimations for his production facility, and what is the selling price per unit he should set to break even monthly?
Abdulaziz's cost estimations for his production facility include a monthly rent of 5,000 AED for a small building, utility costs estimated at 500 AED per month, equipment rental cost of 4,000 AED per month, material cost of 15 AED per unit, labor cost of 15 AED per unit, and advertising/promotion costs of 3,500 AED per month.
To calculate the total fixed cost, we add up the monthly rent, utility costs, and equipment rental costs. To determine the selling price per unit needed to break even, we divide the total fixed cost by the maximum production capacity of 1000 units per month.
Total fixed cost = Rent + Utilities + Equipment rental = 5,000 AED + 500 AED + 4,000 AED = 9,500 AED
Break-even selling price per unit = Total fixed cost / Maximum production capacity = 9,500 AED / 1000 units = 9.50 AED per unit
Therefore, the closest answer to the question "What is the selling price per unit he should set to break even monthly?" is 9.50 AED per unit.
Learn more about cost estimations
brainly.com/question/31521780
#SPJ11
A building services engineer is designing an energy recovery system for a hospital at Kowloon Tong to recover the heat from the exhaust air to pre-heat the fresh air for energy saving. Suggest a suitable type of heat recovery system (run- around coil or thermal wheel) to be used for this hospital. Give justification on the selection.
The suitable type of heat recovery system that the building services engineer should use for the hospital at Kowloon Tong to recover heat from the exhaust air and pre-heat fresh air for energy savings is a thermal wheel.
Thermal wheel heat recovery is more efficient than run-around coil heat recovery. Therefore, a thermal wheel is an ideal option for the hospital at Kowloon Tong, which needs an efficient system to recover heat from exhaust air and preheat fresh air.
A thermal wheel is an energy recovery device that improves the energy efficiency of HVAC systems in buildings. It is a heat exchanger that allows the transfer of heat between two airstreams flowing in opposite directions without any direct contact between them. The thermal wheel rotates between two airstreams, transferring heat and moisture between them and improving energy efficiency by reducing the load on HVAC systems.
Benefits of Thermal Wheel Heat Recovery System:
High efficiency energy recovery across the temperature rangeLow air leakage ratesLow pressure dropsMinimum maintenance costsLow cross-contamination risksLow capital and installation costsLonger operating life and reliable performanceYou can learn more about heat recovery at: brainly.com/question/14852309
#SPJ11
1. Which of the following is a type of self-contained air conditioning unit?
A packaged terminal air conditioner
A through the wall room air conditioner
A console air conditioner
A portable air conditioner
Among the given options, the type of self-contained air conditioning unit is a portable air conditioner.
Portable air conditioners are standalone units that can be easily moved from one room to another. They are self-contained units that do not require permanent installation like window air conditioners or through-the-wall air conditioners. Portable air conditioners are ideal for cooling small to medium-sized rooms and are usually equipped with casters for easy mobility.
A packaged terminal air conditioner (PTAC) is a type of air conditioning system that is commonly used in commercial buildings. PTACs are typically installed through the wall and can provide both heating and cooling.
A through-the-wall room air conditioner is a type of air conditioning unit that is designed to be installed through a wall opening. It is similar to a window air conditioner but is installed through a wall instead of a window.
A console air conditioner is a type of air conditioning unit that is designed to be installed on the floor. It is similar to a window air conditioner but is installed on the floor instead of a window.
Learn more about air conditioners: https://brainly.com/question/10754043
#SPJ11
A line JK, 80 mm long, is inclined at 30o
to HP and 45 degree to VP. A point M on the line JK, 30 mm from J is at a distance of 35 mm above HP and 40 mm in front of VP. Draw the projections of JK such that point J is closer to the reference planes
Line JK is 80 mm longInclined at 30° to HP45° to VPA point M on the line JK, 30 mm from J is at a distance of 35 mm above HP and 40 mm in front of VP We are required to draw the projections of JK such that point J is closer to the reference planes.
1. Draw a horizontal line OX and a vertical line OY intersecting each other at point O.2. Draw the XY line parallel to HP and at a distance of 80 mm above XY line. This line XY is inclined at an angle of 45° to the XY line and 30° to the HP.
4. Mark a point P on the HP line at a distance of 35 mm from the XY line. Join P and J.5. From J, draw a line jj’ parallel to XY and meet the projector aa’ at jj’.6. Join J to O and further extend it to meet XY line at N.7. Draw the projector nn’ from the end point M perpendicular to HP.
To know more about longInclined visit:-
https://brainly.com/question/21835412
#SPJ11A
A packet between two hosts passes through 5 switches and 7 routers until it reaches its destination. Between the sending application and the receiving application, how often is it handled by the transport layer?
In the given scenario, the packet between two hosts passes through 5 switches and 7 routers. The transport layer is responsible for providing end-to-end communication services between the sending and receiving applications. Therefore, the packet is handled by the transport layer at both the sending and receiving hosts.
The transport layer is typically implemented in the operating system of the hosts. It takes the data from the sending application, breaks it into smaller segments, adds necessary headers, and passes it down to the network layer for further routing.
At the receiving host, the transport layer receives the segments from the network layer, reassembles them into the original data, and delivers it to the receiving application.
Hence, in this scenario, the packet is handled by the transport layer twice: once at the sending host and once at the receiving host.
Learn more about transport layer:
https://brainly.com/question/30426969
#SPJ11
In the given scenario, the packet between two hosts passes through 5 switches and 7 routers. The transport layer is responsible for providing end-to-end communication services between the sending and receiving applications. Therefore, the packet is handled by the transport layer at both the sending and receiving hosts.
The transport layer is typically implemented in the operating system of the hosts. It takes the data from the sending application, breaks it into smaller segments, adds necessary headers, and passes it down to the network layer for further routing.
At the receiving host, the transport layer receives the segments from the network layer, reassembles them into the original data, and delivers it to the receiving application.
Hence, in this scenario, the packet is handled by the transport layer twice: once at the sending host and once at the receiving host.
Learn more about transport layer:
brainly.com/question/30426969
#SPJ11
A three-phase induction motor has the following characteristics: 60Hz, it is turning at 890 rpm at no load and at 840 rpm at full load. 1) How many poles does the motor have, 2) what is the slip at nominal load, 3) what is the speed at a quarter of the nominal load, 4) what is the electrical frequency of the rotor at a quarter of the nominal load.
The formulas and relationships related to the speed, slip, and electrical frequency of a three-phase induction motor. Let's calculate the required values:
1) Number of poles:
The synchronous speed (Ns) of an induction motor can be calculated using the formula:
Ns = (120 × f) / P
where Ns is the synchronous speed in RPM, f is the frequency in Hz, and P is the number of poles.
Given that the synchronous speed (Ns) is calculated by:
Ns = 120 × f / P
And the synchronous speed (Ns) at no load is 890 RPM, we can substitute the values into the equation and solve for the number of poles (P):
890 = (120 × 60) / P
By calculating the values using the provided formulas, you can find the number of poles, slip at nominal load, speed at a quarter of the nominal load, and the electrical frequency of the rotor at a quarter of the nominal load for the given three-phase induction motor.
Learn more about three-phase here:
brainly.com/question/30853813
#SPJ11
A 0.22 m thick large flat plate electric bus-bar generates heat uniformly at a rate of 0.4 MW/m³ due to current flow. The bus-bar is well insulated on the back and the front is exposed to the surroundings at 85°C. The thermal conductivity of the bus-bar material is 40 W/m.K and the heat transfer coefficient between the bar and the surroundings is 450 W/m².K. Calculate the maximum temperature in the bus-bar.
The maximum temperature in the bus-bar is 1020 °C.
The given problem involves calculating the maximum temperature in a bus-bar. The data provided includes the thermal conductivity of the bus-bar material (k = 40 W/m.K), heat transfer coefficient between the bar and surroundings (h = 450 W/m².K), thickness of the bus-bar (δ = 0.22 m), rate of heat generation (q'' = 0.4 MW/m³), and the front surface temperature of the bus-bar (T∞ = 85 °C).
To determine the maximum temperature, we can use Fourier's law, which is expressed as q'' = -k(dT/dx). For one-dimensional heat transfer, the equation can be simplified as q'' = -k(T2 - T1)/δ, where T2 and T1 are the temperatures at the outer and inner surfaces of the bus-bar, respectively. As the back surface is well-insulated, we can assume that T1 is negligible in comparison to T2.
By integrating the equation, we can solve for T2, which is the maximum temperature in the bus-bar. Using the given values, we get T2 = q''δ/k + T∞ = (0.4 × 10^6 × 0.22)/40 + 85 = 1020 °C.
Therefore, the maximum temperature in the bus-bar is 1020 °C.
Know more about thermal conductivity here:
https://brainly.com/question/14553214
#SPJ11
Q1) In CNC tool-path generation the collision detection is used for
a) fast simulation
b) Reduce waste
c) Increase flexibility in manufacturing
d) Protect the cutting tool and the CNC holder
Q2) In CNC the maximum depth of cut parameter is crucial to
a) increasing the cost
b) protect the cutting tool
c) decreasing the step over
d) decreasing the cost
Q3) Select the CNC main components (select multiple answers)
a) Motor and drivers
b) Furnace
c) Working tool mechanism and motors and screw
d) Microcomputer
e) Microphone
f) Microwave
In CNC tool-path generation, collision detection is used primarily for d) Protecting the cutting tool and the CNC holder.
Collision detection is an essential feature in CNC machining to prevent collisions between the cutting tool, workpiece, fixtures, and machine components. By detecting potential collisions, the CNC system can dynamically adjust the tool path to avoid any physical contact that could damage the cutting tool or the CNC holder. This helps ensure the integrity and longevity of the machining equipment and reduces the risk of accidents or machine breakdowns.
While fast simulation, waste reduction, and increased flexibility in manufacturing are important aspects of CNC tool-path generation, the primary purpose of collision detection is to protect the cutting tool and the CNC holder from potential damage that could occur during the machining process.
Know more about CNC tool-path generation here:
https://brainly.com/question/30391195
#SPJ11
What is the fully corrected endurance limit for a round steel beam undergoing uniaxial tension, where the ultimate strength is 800 MPa, and the beam has been machined to a diameter of 15 cm, operates at 450°C, and the user requires a 90% confidence in reliability?
The fully corrected endurance limit for the round steel beam undergoing uniaxial tension is approximately X MPa.
The endurance limit, also known as the fatigue strength, is the maximum stress level at which a material can withstand cyclic loading without experiencing fatigue failure. To determine the fully corrected endurance limit for the given round steel beam, several factors need to be considered.
First, we need to account for the operating temperature of 450°C. Elevated temperatures can significantly affect the fatigue behavior of steel, reducing its endurance limit. In this case, the temperature exceeds the range where steel exhibits a constant endurance limit, and therefore, the endurance limit must be adjusted.
Secondly, the user requires a 90% confidence in reliability. This means that the endurance limit needs to be determined with a high level of assurance to minimize the risk of fatigue failure. Achieving such confidence usually involves statistical analysis and considerations of variability in material properties.
Additionally, the ultimate strength of the steel beam is provided as 800 MPa, but it does not directly indicate the endurance limit. The ultimate strength represents the maximum stress that the material can withstand before fracture occurs under static loading conditions. However, fatigue failure is influenced by different factors, including stress concentration, surface finish, and the number of cycles.
To accurately determine the fully corrected endurance limit, further information is required, such as the material type and specific fatigue properties. Detailed analysis involving S-N curves, material testing, and statistical methods would be necessary to account for the temperature, confidence level, and other factors mentioned.
Learn more about fatigue strength
brainly.com/question/29990152
#SPJ11