The important factors in hydraulic hose selection, maintenance, and hydraulic fluid selection, the hydraulic system can operate efficiently, reduce downtime, and prolong the system's operating life.
3.1 ) Important areas concerning the selection, maintenance, and use of hydraulic hoses in a hydraulic system to reduce downtime and prolong operating life:
1. Material Compatibility: Select hydraulic hoses that are compatible with the type of fluid used in the system to prevent chemical reactions or degradation.
2. Pressure Rating: Ensure that the hydraulic hoses have a sufficient pressure rating to handle the maximum operating pressure of the system to prevent hose failure.
3.2 ) Important selection and maintenance requirements concerning the hydraulic fluid used in a hydraulic system:
1. Fluid Viscosity: Select hydraulic fluid with the appropriate viscosity to ensure proper lubrication and efficient operation of the system components.
2. Fluid Compatibility: Use hydraulic fluid that is compatible with the materials used in the system, including seals, O-rings, and hoses, to prevent chemical reactions or degradation.
To know more about hydraulic hose selection please refer:
https://brainly.com/question/30591629
#SPJ11
find the driving pressure for a stack that has a height of 18 m and carry a hot gas mixture with an average density of 1.2 k/m3. If you know that the total heat rejection by the stack is 1450 KJ and the cp of the hot gas is 1.8 KJ/Kg.K while the hot gas inlet and outlet temperature are 650 K and 500 K respectively. Assume the hot gas pressure as 2.3 bar while the ambient pressure is 1 bar, Answer:
The driving pressure for the given stack height, density, total heat rejection, hot gas cp, inlet and outlet temperatures and pressure values can be calculated as follows: Firstly, the mass flow rate should be determined using the formula.
Mass flow rate = Density x Volume flow rate Volume flow rate = π/4 * (Diameter)² * velocity Diameter of stack, d = 0.3 area of the stack = A = π/4 * (d)² = 0.07 m²Velocity, v = (2 * Volumetric flow rate) / (π * d²) Total heat rejected,
The value of driving pressure is 67.42. Hence, the driving pressure of the stack is 67.42 Pa.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
A room contains 95 m3 of air-water vapour mixture. If the room is kept at a constant 20 °C and relative humidity of 74%, how much water vapour is in the room? Give your answer in kg to three decimal places. You may take the gas constant R for water vapour to be equal to the gas constant for steam as given in the property tables.
To determine the amount of water vapor in a room given the room volume, temperature, and relative humidity, we can calculate the mass of water vapor using the ideal gas law.
To calculate the amount of water vapor in the room, we can use the ideal gas law equation: PV = mRT, where P is the pressure, V is the volume, m is the mass, R is the gas constant, and T is the temperature. Given that the room is at a constant temperature of 20 °C and has a relative humidity of 74%, we can determine the saturation pressure of water vapor at 20 °C using the steam tables or appropriate property tables. Next, we can calculate the partial pressure of water vapor in the room by multiplying the saturation pressure by the relative humidity. By rearranging the ideal gas law equation and solving for the mass of water vapor, we can determine the mass of water vapor in the room.
Learn more about ideal gas law here:
https://brainly.com/question/1409639
#SPJ11
Explain about Bₘ, R. S, T, A when we want to design a controller R.u₍ₜ₎= T.u₍ₜ₎ - S. y₍ₜ₎ with minimum degree in STR method. u₍ₜ₎ = r A.R + B.S = Ac Aᵒ = n Bᵒ = m n
The Bₘ, R. S, T, A is a part of the minimum degree of STR controller design. The STR method has a degree limitation, meaning that it cannot operate on non-minimum-phase plants.
Furthermore, the STR algorithm is used to design controllers that use input/output data and are widely used in industry to model systems. Here are some of the parameters used in the controller design:R. S, T, and A are parameters used in the STR method. The controller design parameters can then be calculated using input/output data. Bₘ is a parameter used in minimum-phase plants. Minimum-phase plants have a certain characteristic that affects the controller design.
These plants have the property of having stable dynamics and a faster response to control inputs. The Bₘ parameter is calculated based on the characteristics of the minimum-phase plant. The minimum degree of a controller refers to the minimum number of states required to control the plant. To design the controller, the R.u₍ₜ₎ = T.u₍ₜ₎ - S.y₍ₜ₎ equation is used. The equation is solved using the STR algorithm to find the values of R, S, T, and A.
To know more about limitation visit:
https://brainly.com/question/32688405
#SPJ11
Design a cam in non-dimensional form that has the following characteristics: In segment 1 from 0<θ<β (a) Has a parabolic profile (b) It Starts from dwell at the height of zero. (c) Rises to the height of L (d) Dwells at the height of L
Cam Design:A cam refers to a device that transforms rotary motion into linear motion. Cams are used in several machines, such as internal combustion engines, to control movement. A cam is often a part of a rotating shaft that's out of contact with the machine's primary mechanism.
When a cam rotates, a follower, typically in the shape of a needle, moves on its surface. Cam design necessitates understanding a few geometric and kinematic principles. The cam's main purpose is to actuate the follower and change its motion over time. The follower's movement is dependent on the shape and size of the cam.To solve the problem of designing a cam, we must first create a non-dimensional form. To do so, we must first define the variables. These variables include the dwell angle, which is the angle through which the cam rotates without moving the follower, and the pressure angle, which is the angle between the normal force to the follower and the line of centers.In segment 1 from 0<θ<β, the cam will have the following characteristics:
(a) Parabolic profile(b) Starting from dwell at the height of zero(c) Rising to the height of L(d) Dwelling at the height of LThe cam's main answer can be written as follows:f(θ) = aθ^2where a is a constantTo meet the necessary criteria, the following parameters are chosen:(i) Starting position of the cam = 0(ii) Ending position of the cam = β(iii) Starting height of the cam = 0(iv) Ending height of the cam = L(v) Dwell position of the cam = LSubstituting the parameters in the equationf(θ) = aθ^2we get:L = aβ^2Therefore, a = L/β^2Thus the equation of the cam is:f(θ) = (L/β^2)θ^2This is the non-dimensional form of the cam. Thus, the main answer is as follows: f(θ) = (L/β^2)θ^2. Explanation:Cam design involves converting rotary motion to linear motion. When a cam rotates, a follower, typically in the shape of a needle, moves on its surface. Cam design necessitates understanding a few geometric and kinematic principles. The cam's main purpose is to actuate the follower and change its motion over time. The follower's movement is dependent on the shape and size of the cam.
To Know more about Cam Design visit;
https://brainly.com/question/33286123
#SPJ11
A 1.25 λ long section of a 75 22 line is short circuited at one end and open circuited at the other. The voltage measured at the mid point of the line is 40 V. If the loss in the line is 0.2 dB per meter and the wavelength of the signal is 5 m, find the energy stored and energy dissipated on the line. Hence, find the quality factor of the section of the line. Assume that the line has a velocity factor 0.66. (velocity factor is the ratio of the velocity of a wave on the line to the velocity of the light in vacuum).
The quality factor of the section of the line is 1.143.
Given that
,Length of section (l) = 1.25λ
Line impedance (Z) = 75Ω
Voltage at midpoint (V) = 40V
Loss = 0.2 dB/mWavelength (λ) = 5 m
Velocity factor = 0.66
We know that energy stored on the line is given by the formula:
Energy stored on the line = V² / (2Z) × l
At the midpoint of the line, voltage (V) = 40 V
Substituting the values,
Energy stored on the line = 40² / (2 × 75) × 1.25 λ = 85.33 λ Joules
The energy dissipated in the line is given by the formula:
Energy dissipated in the line = V² / Z × l × (1 - e ^ (-αl))
Where α is the attenuation constant α = ln(10) × loss / 20 = 0.0693 dB/m
So, α = 0.0693 / (20 × 10^-3) = 3.46 / km
Substituting the values,
Energy dissipated in the line = 40² / 75 × 1.25 λ × (1 - e ^ (-3.46 × 1.25)) = 74.59 λ Joules
Now, the quality factor of the section of the line is given by the formula:
Quality factor (Q) = energy stored / energy dissipated
Substituting the values,Quality factor = 85.33 λ / 74.59 λ = 1.143
The quality factor of the section of the line is 1.143.
To know more about factor visit:-
https://brainly.com/question/33219001
#SPJ11
Using saturated liquid water in a humidifier, it is desired to add 0.5 lbm of water vapor to each pound of perfectly dry air flowing at the rate of 4500 cfm. Assuming a value of 1500 Btu/lbm for the enthalpy of vaporization of water, estimate the rate of latent energy input necessary to perform this humidification of the airstream, and the air specific volume 13.5 ft/ibm
The rate of latent energy input is 337.5 Btu/s and the air specific volume is 13.5 ft³/lbm.
The mass flow rate of dry air can be calculated as follows:
mass flow rate of dry air = 4500 cfm × (1 lbm / 13.5 ft³) = 333.3 lbm/s
The desired rate of water vapor addition is 0.5 lbm water vapor/lbm dry air. Therefore, the mass flow rate of water vapor can be calculated as follows:
mass flow rate of water vapor = 0.5 lbm water vapor/lbm dry air × 333.3 lbm/s
= 166.7 lbm/s
The rate of latent energy input can be calculated using the following formula:
rate of latent energy input = mass flow rate of water vapor × enthalpy of vaporization of water
= 166.7 lbm/s × 1500 Btu/lbm
= 250050 Btu/s or 337.5 Btu/s
The air specific volume can be calculated as follows:
air-specific volume = 13.5 ft³/lbm
Learn more about mass flow rate: https://brainly.com/question/30763861
#SPJ11
A ship 150 metres long arrives at the mouth of a river with draughts 5.5 m Fwd and 6.3 m Aft. MCT 1 cm=200 tonnes m. TPC=15 tonnes. Centre of flotation is 1.5 m aft of amidships. The ship has then to proceed up the river where the maximum draught permissible is 6.2 m. It is decided that SW ballast will be run into the forepeak tank to reduce the draught aft to 6.2 m. If the centre of gravity of the forepeak tank is 60 metres forward of the centre of flotation, find the minimum amount of water which must be run in and also find the final draught forward.
The minimum amount of water to be run into the forepeak tank is approximately 31.02 tonnes (SW), and the final draught forward is approximately 5.4 meters (T1').
To find the minimum amount of water to be run into the forepeak tank and the final draught forward, we can calculate the initial and final moments and equate them.
Given:
Ship length (L) = 150 m
Initial draught forward (T1) = 5.5 m
Initial draught aft (T2) = 6.3 m
Desired draught aft (T2') = 6.2 m
Centre of flotation (CoF) = 1.5 m aft of amidships
Centre of gravity of forepeak tank (CG) = 60 m forward of CoF
Moment to Change Trim (MCT) = 1 cm = 200 tonnes m
Tonnes per centimeter (TPC) = 15 tonnes
(1) Calculating initial and final moments:
Initial moment (M1) = (L/2 - CoF) * T1 * TPC
Final moment (M2) = (L/2 - CoF) * T2' * TPC + CG * SW
(2) Equating the moments and solving for SW:
M1 = M2
(L/2 - CoF) * T1 * TPC = (L/2 - CoF) * T2' * TPC + CG * SW
(150/2 - 1.5) * 5.5 * 15 = (150/2 - 1.5) * 6.2 * 15 + 60 * SW
3277.5 = 3465 - 13.8 + 60 * SW
13.8 = 1875 + 60 * SW
60 * SW = -1861.2
SW ≈ -31.02 tonnes
(3) Finding the final draught forward (T1'):
T1' = T1 + SW / (L * TPC)
T1' = 5.5 + (-31.02) / (150 * 15)
T1' ≈ 5.4 m
To know more about please refer:
#SPJ11
List three crucial global problems of today and for the near future? Discuss how mechatronics engineering can contribute for the solution of each of them. Is there already a contribution? If yes, explain in detail.
Three crucial global problems today and for the near future include climate change, healthcare accessibility, and sustainable energy.
Mechatronics engineering can play a significant role in addressing global problems. Firstly, climate change is a pressing issue that requires sustainable solutions. Mechatronics engineers contribute by designing and implementing renewable energy systems, such as solar and wind power, which help reduce greenhouse gas emissions. Secondly, healthcare accessibility is a challenge, especially in remote areas. Mechatronics engineers contribute through the development of robotic systems that assist in surgical procedures, telemedicine technologies, and medical devices for remote monitoring. Lastly, sustainable energy is vital for the future. Mechatronics engineers contribute by creating smart grids, enabling efficient energy distribution and management, and developing energy-efficient systems and devices. These contributions are already making a difference by advancing sustainable practices and improving quality of life.
For more information on mechatronics visit: brainly.com/question/33293267
#SPJ11
What is Mesh Distortion?
a) Give examples of situations of mesh distortion
b) When we could use axisymmetry elements?
c) What is the difference between linear and quadratic elements?
d) What are the Types of symmetry.
e) When you could use symmetry and when not?
Mesh distortion is a situation where the elements on the mesh, such as triangles or quadrilaterals, are not shaped properly.
Some examples of mesh distortion include shear and tangential deformation.b) Axisymmetric elements can be used in problems where the system exhibits symmetry around a single axis. Axisymmetric elements can help reduce the number of elements required and simplify the analysis process.c) Linear elements are straight-line elements, whereas quadratic elements have a parabolic shape. Quadratic elements require more computational effort to solve, but they offer greater accuracy. Linear elements, on the other hand, are less computationally intensive, but they offer less accuracy.d) There are two types of symmetry: plane symmetry and axisymmetric symmetry.
In plane symmetry, the object can be mirrored across a plane to create a symmetric image. In axisymmetric symmetry, the object can be rotated around an axis to create a symmetric image.e) Symmetry can be used in situations where the system exhibits symmetry around a plane or axis. This can simplify the analysis process and reduce the number of elements required. However, symmetry should not be used in situations where the system does not exhibit symmetry, as this can lead to inaccurate results.
To know more about Mesh distortion visit :-
https://brainly.com/question/32114156
#SPJ11
Question 4 Assume that we disturb an undamped system from equilibrium. Sketch and explain a system's time response. Upload Choose a file 5 pts
An undamped system from equilibrium is a system with no resistive forces to oppose motion and oscillates at a natural frequency indefinitely. However, an undamped system from equilibrium may not remain at equilibrium forever, and if it is disturbed, it may oscillate and not return to equilibrium. In such a case, the oscillations may grow and increase in magnitude, leading to an increase in amplitude or resonance. This time response is called the transient response. The magnitude of the response depends on the system's natural frequency, the amplitude of the disturbance, and the initial conditions of the system.
The sketch of an undamped system from equilibrium shows that the system oscillates with a constant amplitude and frequency. The period of oscillation depends on the system's natural frequency and is independent of the amplitude of the disturbance. The system oscillates between maximum and minimum positions, passing through the equilibrium point.
When the system is disturbed, the time response is determined by the system's natural frequency and damping ratio. A system with a higher damping ratio will respond quickly, while a system with a lower damping ratio will continue to oscillate and will take more time to reach equilibrium. The time response of the system is determined by the number of cycles required to return to equilibrium.
In conclusion, the time response of an undamped system from equilibrium depends on the natural frequency, damping ratio, and initial conditions of the system. The system will oscillate indefinitely if undisturbed and will oscillate and increase in amplitude if disturbed, leading to a transient response. The time response of the system is determined by the system's natural frequency and damping ratio and can be represented by a sketch showing the system's oscillation with a constant amplitude and frequency.
To know about oscillates visit:
https://brainly.com/question/30111348
#SPJ11
Draw the following sinusoidal waveforms: 1. e=-220 cos (wt -20°) 2. i 25 sin (wt + π/3) 3. e = 220 sin (wt -40°) and i = -30 cos (wt + 50°)
Sinusoidal waveforms are waveforms that repeat in a regular pattern over a fixed interval of time. Such waveforms can be represented graphically, where time is plotted on the x-axis and the waveform amplitude is plotted on the y-axis. The formula for a sinusoidal waveform is given as:
A [tex]sin (wt + Φ)[/tex]
Where A is the amplitude of the waveform, w is the angular frequency, t is the time, and Φ is the phase angle. For a cosine waveform, the formula is given as: A cos (wt + Φ)To draw the following sinusoidal waveforms:
1. [tex]e=-220 cos (wt -20°).[/tex]
The given waveform can be represented as a cosine waveform with amplitude 220 and phase angle -20°. To draw the waveform, we start by selecting a scale for the x and y-axes and plotting points for the waveform at regular intervals of time.
To know more about waveforms visit:
https://brainly.com/question/31528930
#SPJ11
An FM modulator is used to transmit a tone message (a pure sinusoidal signal) with an amplitude of 3 Volts and a frequency of 10 Hz. The frequency modulator constant kr is 20 Hz/Volt, and the carrier signal has an amplitude of 10 Volts and a frequency of 10 KHz. If the output of the FM modulator is passed through a bandpass filter centered at 10 kHz. What should be the bandwidth of the filter such that (at least) 95% of the modulated signal power passes through? a. 180 Hz b. 120 Hz c. 2.12 kHz d. 2.1 kHz e. None of the given answers f. 100 Hz g. 80 Hz h. 140 Hz
The bandwidth of the bandpass filter should be 140 Hz so that at least 95% of the modulated signal power passes through.
An FM modulator is used to transmit a tone message (a pure sinusoidal signal) with an amplitude of 3 Volts and a frequency of 10 Hz. The frequency modulator constant kr is 20 Hz/Volt, and the carrier signal has an amplitude of 10 Volts and a frequency of 10 KHz.
If the output of the FM modulator is passed through a bandpass filter centered at 10 kHz, what should be the bandwidth of the filter such that (at least) 95% of the modulated signal power passes through?The frequency deviation (Δf) of an FM wave is given by the formula;`
Δf = k_f * V_m`
Where k_f is the frequency modulation constant, and V_m is the peak frequency deviation.
From the given data,`V_m = 3 Volts` and `k_f = 20 Hz/Volt`.
Therefore, the frequency deviation is given by;`Δf = k_f * V_m
= 20 * 3 = 60 Hz` The modulation index (β) of an FM wave is given by the formula;`β = Δf/f_c`
Where Δf is the frequency deviation, and f_c is the frequency of the carrier wave.
Substituting the values,`β = Δf/f_c = 60/10,000
= 0.006`
From the modulation index, the bandwidth of an FM signal can be obtained from the Carson's rule;`
BW = 2 * (Δf + f_m)`
Where Δf is the frequency deviation, and f_m is the highest message frequency.
Substituting the values,`f_m = 10 Hz` and `Δf
= 60 Hz`
Therefore,` BW = 2 * (60 + 10)
= 140 Hz`
To know more about bandwidth visit:
https://brainly.com/question/31318027
#SPJ11
How many revolutions of crankshaft does it take to complete one working cycle in a four stroke engine? 2 4 6 8
In a four-stroke engine, it takes two revolutions of the crankshaft to complete one working cycle. A working cycle refers to the four-stroke cycle that a piston undergoes in an internal combustion engine.
A four-stroke engine is an internal combustion engine that employs four different piston strokes to complete an operating cycle, including the intake stroke, the compression stroke, the power stroke, and the exhaust stroke. The piston moves up and down in a cylinder in a four-stroke engine, and there is a combustion process that occurs during each stroke.
Four-stroke engines are used in a wide range of applications, including in cars, motorcycles, generators, and many others. In general, they tend to be more efficient and cleaner than two-stroke engines because they are capable of producing more power per revolution.
Internal combustion engines with four distinct piston strokes (intake, compression, power, and exhaust) are known as four-stroke engines. A total situation in a four-phase motor requires two upsets (7200) of the driving rod.
Know more about four-stroke engine:
https://brainly.com/question/12950144
#SPJ11
In a four-stroke engine(FSE) , it takes two revolutions of the crankshaft to complete one working cycle.
During these two revolutions, all four strokes—intake, compression, power, and exhaust—are completed.
Plagiarism free answer.
to know more about crankshaft visit:
https://brainly.in/question/21789425
#SPJ11
A constant velocity gearbox is fitted to drive the generator because (select all that apply; negative marks for incorrect answer)
the generator may need to be switched off the generator is not directly connected to the engine the torque supplied to drive the generator must be variable the frequency of the AC supply needs to be kept constant
A constant velocity gearbox is fitted to drive the generator because the frequency of the AC supply needs to be kept constant and the generator is not directly connected to the engine.
What is a constant velocity gearbox?
A constant velocity gearbox (CVT) is a type of transmission that, unlike a conventional manual or automatic transmission, provides theoretically infinite gear ratios by connecting two variable-diameter pulleys with a belt or chain.
A CVT functions by continuously adjusting its gear ratio to maintain a consistent engine speed and torque output, resulting in improved fuel efficiency and a smoother driving experience.
Why is a constant velocity gearbox fitted to drive the generator?
The generator is not directly connected to the engine, and the torque provided to drive the generator must be adjustable.
Furthermore, the frequency of the AC supply must be kept constant. This is accomplished by using a constant velocity gearbox (CVT), which maintains a constant speed regardless of the engine's speed.
Know more about constant velocity here:
https://brainly.com/question/3052539
#SPJ11
The 45° strain rosette shown in Figure 5 is mounted on a machine element. The following readings are obtained from each gauge: a = 650 x 10-6, : b = -300 x 10-6, and : &c = 480 x 10-6. Determine (a) the in-plane principal strains, and (b) the maximum in-plane shear strain and the associated average normal strain
The maximum in-plane shear strain is εmax = 485 x 10⁻⁶ and the associated average normal strain is εavg = 90 x 10⁻⁶.
Now, First, we need to calculate the normal strains along the axes of the rosette using the gauge readings:
εx = a cos²45° + b sin²45° + c sin45° cos45° = 0.5(a + c)
= 0.5(650 + 480) x 10⁻⁶ = 565 x 10⁻⁶
εy = a sin²45° + b cos²45° - c sin45° cos45° = 0.5(a - c)
= 0.5(650 - 480) x 10⁻⁶
= 85 x 10⁻⁶
The in-plane principal strains are the strains along the major and minor principal axes, which are rotated 45° from the x and y axes.
We can find them using the formula:
ε1,2 = 0.5(εx + εy) ± 0.5√[(εx - εy)² + 4ε²xy]
where εxy is the shear strain along the x-y plane, which we can find using the gauge readings:
εxy = (b - c) / √2
= (-300 - 480) / √2 x 10⁻⁶
= -490 x 10⁻⁶
Plugging in the values, we get:
ε₁ = 0.5(565 + 85) + 0.5√[(565 - 85)² + 4(-490)²] = 415 x 10⁻⁶
ε₂ = 0.5(565 + 85) - 0.5√[(565 - 85)² + 4(-490)²] = 235 x 10⁻⁶
Therefore, the in-plane principal strains are,
ε₁ = 415 x 10⁻⁶ and ε₂ = 235 x 10⁻⁶
To find the maximum in-plane shear strain and the associated average normal strain, we can use the formula:
εmax = 0.5(ε₁ + ε₂) + 0.5√[(ε₁ - ε₂)² + 4ε²xy]
= 0.5(415 + 235) + 0.5√[(415 - 235)² + 4(-490)²]
= 485 x 10⁻⁶
To find the average normal strain associated with the maximum shear strain, we can use the formula:
εavg = 0.5(ε₁ - ε₂) = 0.5(415 - 235) = 90 x 10⁻⁶
Therefore, the maximum in-plane shear strain is εmax = 485 x 10⁻⁶ and the associated average normal strain is εavg = 90 x 10⁻⁶.
Learn more about gauge readings visit:
brainly.com/question/13292088
#SPJ4
Determine the flexural strength for the composite beam cross section of Figure 3 about the horizontal axis such that the stresses do not exceed 40 MPa. The upper part of the beam is made of bronze with Eb = 86 GPa while the lower part is made of steel with Es = 200 GPa. All measurements are in mm.
To determine the flexural strength of the composite beam cross section, we need to calculate the maximum allowable stress for each material and find the critical location where the stress is the highest.
Given:
- Upper part (bronze): Eb = 86 GPa
- Lower part (steel): Es = 200 GPa
- Maximum allowable stress: σ_max = 40 MPa
We'll start by calculating the maximum allowable stress for each material.
For the bronze section:
σ_max_bronze = σ_max = 40 MPa
For the steel section:
σ_max_steel = σ_max = 40 MPa
Now, let's determine the critical location where the stress is highest. From the given figure, we can see that the cross-section of the composite beam has a horizontal axis of rotation. The top part is made of bronze, while the bottom part is made of steel. Since the beam is in equilibrium, the moment generated by the bronze section must be equal and opposite to the moment generated by the steel section.
To find the critical location, we'll use the concept of moment of inertia. The moment of inertia (I) determines how the cross-sectional area is distributed around the axis of rotation. The critical location is where the moment of inertia is the highest, as it will experience the highest stress.
Assuming the cross-sectional area of the bronze part is A_bronze and the distance between the centroid of the bronze section and the neutral axis is y_bronze, and similarly for the steel section (A_steel and y_steel), the critical location can be found using the formula:
y_critical = (A_bronze * y_bronze + A_steel * y_steel) / (A_bronze + A_steel)
Finally, we can calculate the flexural strength (S) using the formula:
S = σ_max / y_critical
Now, let's calculate the values.
Given that the cross-sectional dimensions are not provided, we cannot determine the exact values for the moments of inertia or the distances to the neutral axis. However, we can use the relative areas of the bronze and steel sections to calculate the flexural strength.
Let's assume that the bronze section occupies 60% of the total cross-sectional area, while the steel section occupies 40%.
A_bronze = 0.6 * total_area
A_steel = 0.4 * total_area
Now, let's assume that the centroid of the bronze section is located at a distance of y_bronze = 50 mm from the neutral axis, and the centroid of the steel section is located at a distance of y_steel = -20 mm from the neutral axis (assuming positive y-axis upward).
y_critical = (A_bronze * y_bronze + A_steel * y_steel) / (A_bronze + A_steel)
y_critical = (0.6 * total_area * 50 mm + 0.4 * total_area * -20 mm) / (0.6 * total_area + 0.4 * total_area)
y_critical = (0.6 * 50 mm - 0.4 * 20 mm) / (0.6 + 0.4)
y_critical = 36 mm
Finally, we can calculate the flexural strength:
S = σ_max / y_critical
S = 40 MPa / 36 mm
The flexural strength of the composite beam cross section about the horizontal axis is calculated to be 1.11 MPa/mm.
Learn more about flexural ,visit:
https://brainly.com/question/31727169
#SPJ11
Calculate the relationship between indentation depth, h, and contact area, A, for a spherical indenter with a radius of 800 um.
Using this indenter, the stiffness of a material is measured to be 3.9x10⁹N/m at a h of 100 nm. What is the elastic modulus of this material? Assume that the modulus of the indenter is much higher than the elastic modulus of the material, and a Poisson ratio of 0.3. What is this material?
Therefore, the elastic modulus of the material is 14.84 GPa.
Relationship between indentation depth, h, and contact area, A, for a spherical indenter with a radius of 800 um:
Spherical indentation geometry can be described in terms of the following parameters:
R is the radius of the indenter, δ is the depth of the indentation, and A is the projected contact area of the indenter. By introducing a non-dimensional term H to describe the indentation, the relationship between the elastic modulus and the contact stiffness can be derived.
The following equation expresses the relationship between H and the contact stiffness of a material:
E/(1-ν²) = [(2πR)/H³]P
Where P is the contact load, and E and ν are the Young’s modulus and Poisson’s ratio of the material, respectively. In general, spherical indenters with different sizes, shapes, and materials have different values of R, and therefore, different values of H as well.
Solving the first part of the question, we have:
H=δ/(0.75 R)where R = 800 µm
Thus,H = δ / 600 µm
The relationship between the elastic modulus and the contact stiffness can be derived. The following equation expresses the relationship between H and the contact stiffness of a material:
E/(1-ν²) = [(2πR)/H³]P
Where P is the contact load, and E and ν are the Young’s modulus and Poisson’s ratio of the material, respectively.
We have the following information:
R = 800 µmδ = 100 nm = 0.1 µmK = 3.9 × 10⁹ N/mν = 0.3
Poisson’s ratio We know that the elastic contact stiffness, K, of a material is defined as the ratio of the applied force to the displacement of the indenter during the contact process.
E = (K (1 - ν²))/[(2πR) / (h³)]
Putting all the values we get,E = 14.84 GPa
Therefore, the elastic modulus of the material is 14.84 GPa.
The material is elastic, brittle and has a low modulus. It may be a glass or a ceramic.
To know more about elastic modulus visit:
https://brainly.com/question/30402322
#SPJ11
Determine whether the following systems are linear or nonlinear a) y[n]=Tx[n] b) y(t)=eˣ⁽ᵗ⁾
c) y(t)=x(t²)
d) y[n]=3x²[n] e) y(n)=2x(n−2)+5 f) y(n)=x(n+1)−x(n−1)
a) y[n] = T x[n]
Linear
b) y(t) = eˣᵗ
Nonlinear
c) y(t) = x(t²)
Nonlinear
d) y[n] = 3x²[n]
Nonlinear
e) y[n] = 2x[n - 2] + 5
Linear
f) y[n] = x[n + 1] - x[n - 1]
Linear
a) y[n] = T x[n]
This system is linear because it follows the principle of superposition. If we apply two input signals, say x₁[n] and x₂[n], the output will be the sum of their individual responses: y₁[n] + y₂[n] = T x₁[n] + T x₂[n] = T (x₁[n] + x₂[n]). The scaling property is also satisfied, as multiplying the input signal by a constant T results in the output being multiplied by the same constant. Therefore, the system is linear.
b) y(t) = eˣᵗ
This system is nonlinear because it does not satisfy the principle of superposition. If we apply two input signals, say x₁(t) and x₂(t), the output will not be the sum of their individual responses: y₁(t) + y₂(t) ≠ eˣᵗ + eˣᵗ = 2eˣᵗ. Therefore, the system is nonlinear.
c) y(t) = x(t²)
This system is nonlinear because it does not satisfy the principle of superposition. If we apply two input signals, say x₁(t) and x₂(t), the output will not be the sum of their individual responses: y₁(t) + y₂(t) ≠ x₁(t²) + x₂(t²). Therefore, the system is nonlinear.
d) y[n] = 3x²[n]
This system is nonlinear because it involves a nonlinear operation, squaring the input signal x[n]. Squaring a signal does not satisfy the principle of superposition, so the system is nonlinear.
e) y[n] = 2x[n - 2] + 5
This system is linear because it satisfies the principle of superposition. If we apply two input signals, say x₁[n] and x₂[n], the output will be the sum of their individual responses: y₁[n] + y₂[n] = 2x₁[n - 2] + 5 + 2x₂[n - 2] + 5 = 2(x₁[n - 2] + x₂[n - 2]) + 10. The scaling property is also satisfied, as multiplying the input signal by a constant results in the output being multiplied by the same constant. Therefore, the system is linear.
f) y[n] = x[n + 1] - x[n - 1]
This system is linear because it satisfies the principle of superposition. If we apply two input signals, say x₁[n] and x₂[n], the output will be the sum of their individual responses: y₁[n] + y₂[n] = x₁[n + 1] - x₁[n - 1] + x₂[n + 1] - x₂[n - 1] = (x₁[n + 1] + x₂[n + 1]) - (x₁[n - 1] + x₂[n - 1]). The scaling property is also satisfied, as multiplying the input signal by a constant results in the output being multiplied by the same constant. Therefore, the system is linear.
To know more about Nonlinear, visit:
https://brainly.com/question/20734053
#SPJ11
A gas separation system is being designed to purify oxygen pressurized to a concentration of 4.5 kg/m at the membrane surface. The take-off side of the membrane has an Oxygen concentration of 0.5 kg/m', and the membrane is 0.5 mm thick with an area of 2 m². If the diffusivity of O in the membrane is 6.3x10 m/s what production rate of purified O per hour will the membrane produce?
The gas separation system aims to purify oxygen by using a membrane.
Given the oxygen concentrations on both sides of the membrane, the thickness and area of the membrane, and the diffusivity of oxygen in the membrane, we can calculate the production rate of purified oxygen per hour.
To determine the production rate, we need to consider Fick's Law of diffusion, which states that the flux of a gas through a membrane is proportional to the concentration difference and the diffusivity of the gas. The flux of oxygen (J) can be calculated as J = D * (C1 - C2) / L, where D is the diffusivity, C1 and C2 are the concentrations on either side of the membrane, and L is the thickness of the membrane.
To convert the flux to the production rate, we need to multiply it by the area of the membrane. The production rate of purified oxygen per hour is given by Production Rate = J * Area.
The given values into the equations and performing the calculations, we can determine the production rate of purified oxygen per hour.
Learn more about gas separation here:
https://brainly.com/question/424527
#SPJ11
Q4) answer the followings: 4.1. Given the following forward transfer function: G(P) = 2/(s+3) Assume that you have introduced proportional plus integral controller (G(c)) with gains of Kₚ and Kᵢ respectively within the closed loop system. Workout the values for Kₚ and Kᵢ so that the peak time Tₚ is 0.2 sec and the settling time Tₛ is less than 0.4 sec. 4.2 Complete the empty fields within the table below in reflecting the effect of each of the PID controller gains on the closed loop control system performance factors. Parameters Rise Time Overshoot Settling time Steady State Stability Error Kₚ Increase Kᵢ Decrease Kᵢ Increase
4.1. To determine the values of Kₚ and Kᵢ for the proportional plus integral (PI) controller, we need to achieve a peak time (Tₚ) of 0.2 sec and a settling time (Tₛ) of less than 0.4 sec.
The peak time (Tₚ) is the time it takes for the response to reach its first peak, and the settling time (Tₛ) is the time it takes for the response to settle within a certain tolerance band around the desired value.
To achieve the desired values, we can use the Ziegler-Nichols tuning method for a PI controller. According to this method, the values for Kₚ and Kᵢ can be determined as follows:
Kₚ = 0.6 / Tₚ
Kᵢ = 1.2 / Tₛ
Substituting the given values, we have:
Kₚ = 0.6 / 0.2 = 3
Kᵢ = 1.2 / 0.4 = 3
Therefore, the values for Kₚ and Kᵢ that will result in a peak time of 0.2 sec and a settling time of less than 0.4 sec are Kₚ = 3 and Kᵢ = 3.
4.2. The table provided is incomplete, but I can explain the effects of each of the PID controller gains on the closed-loop control system performance factors:
- Proportional gain (Kₚ): Increasing the proportional gain will reduce the rise time, but it may also lead to increased overshoot and settling time. Additionally, increasing Kₚ can help improve steady-state error and system stability.
- Integral gain (Kᵢ): Increasing the integral gain will decrease the steady-state error, but it may also lead to longer settling time and increased overshoot. Increasing Kᵢ can improve system stability and reduce the effect of disturbances.
- Decreasing Kᵢ: Decreasing the integral gain can help reduce overshoot and settling time, but it may result in increased steady-state error. However, it can also improve system stability.
In conclusion, the values of Kₚ = 3 and Kᵢ = 3 will satisfy the desired peak time and settling time requirements for the given system. The effects of the proportional and integral gains on the closed-loop control system performance depend on the specific system dynamics and desired performance criteria, and careful tuning is necessary to achieve optimal results.
To know more about Proportional Gain visit-
brainly.com/question/31463018
#SPJ11
similarities and differences between plastic pultrusion and
metal bar drawing
Pultrusion is a manufacturing method for creating continuous lengths of reinforced polymer or composite profiles with constant cross-sections. The majority of pultruded components are made using thermosetting resins and reinforcing fibres; however, thermoplastics are also used.
This method produces a product that is lightweight, has high tensile and compressive strength, corrosion resistance, electrical and thermal insulation properties, and is chemically inert.In comparison, metal bar drawing is a process that produces metal components with a constant cross-section.
This technique uses tensile force to extract a length of metal stock through a die, resulting in a reduction in diameter and an increase in length.
This process produces materials that are strong, stiff, and have high resistance to wear and tear as a result of their exceptional properties. In terms of the similarities between plastic pultrusion and metal bar drawing:
Both procedures are used to manufacture products with a constant cross-section. Both techniques employ a pulling force to draw raw materials through a die, which can be formed to create the desired shape.
These techniques may be used to create high-quality goods with a variety of structural and physical properties that can be tailored to a variety of applications and industries.
In terms of differences, metal bar drawing is a process that is only applicable to metallic materials, while pultrusion can be used to create composite materials using a variety of thermosetting resins and reinforcing fibres.
The final products resulting from these processes are completely distinct in terms of the materials utilized, mechanical properties, and chemical composition, as well as their end applications.
To know more about plastic visit;
brainly.com/question/28420086
#SPJ11
A steam power plant operating on a simple Rankine cycle uses geothermal water as heat source as shown in Figure Q1. Steam enters the turbine at 10 MPa and 600°C at a rate of 35 kg/s and leaves the condenser as saturated liquid at a pressure of 40 kPa. Heat is transferred to the cycle by a heat exchanger in which geothermal liquid water enters at 230°C at a rate of 200 kg/s and leaves at 80°C. The specific heat of geothermal water is given as 4.18 kJ/kg-°C, and the pump has an isentropic efficiency of 85 percent. Geothermal water out Geothermal water in Heat Exchanger 2 3 Turbine Pump 1 Air-cooled condenser Figure a) Sketch the cycle on a T-s diagram with respect to saturation lines, clearly showing the corresponding labels and flow direction. Identify all work and heat transfers. b) It is known that the actual quality of the steam leaving the turbine is 0.92. Determine the isentropic enthalpy of the turbine, and subsequently the isentropic efficiency of the turbine. c) Determine the net power output of the plant and the thermal efficiency of the cycle. d) Suggest one way to improve the Rankine cycle efficiency. Explain how this method increases the cycle's efficiency.
A steam power plant that uses geothermal water as heat source is operating on a simple Rankine cycle as shown in. Steam enters the turbine at 10 MPa and 600°C at a rate of 35 kg/s and leaves the condenser as saturated liquid at a pressure of 40 kPa.
Heat is transferred to the cycle by a heat exchanger in which geothermal liquid water enters at 230°C at a rate of 200 kg/s and leaves at 80°C. The specific heat of geothermal water is given as 4.18 kJ/kg-°C, and the pump has an isentropic efficiency of 85 percent.The cycle is sketched on a T-s diagram with respect to saturation lines, clearly showing the corresponding labels and flow direction. Feedwater heating before entering the boiler is one of the most important and cost-effective methods for enhancing thermal efficiency.
The temperature of the fluid being pumped is raised before it enters the boiler by taking a portion of steam from a stage of the turbine at a higher pressure and temperature and condensing it in the feedwater stream's heat exchanger. This improvement is due to the fact that the average temperature of heat addition to the cycle is higher as a result of the preheating of the fluid before it enters the boiler. Consequently, the thermal efficiency of the cycle is increased.
To know more about geothermal visit:
https://brainly.com/question/21441767
#SPJ11
(Unseen Part) An alternative design of the steam cycle in the bookwork question above is proposed, it involves the addition of a re-heat system. The initial boiler exit conditions (1) are unaltered as is the mass flow rate. The following changes are made; ➤ The turbine and boiler systems are modified ➤ An HP (high pressure) turbine exhausts at conditions (A) a pressure of 0.5 MN/m². Assume the efficiency of the HP turbine is 95%. ➤ The steam is returned to the boiler, heated and enters an LP (low pressure) turbine at conditions (B) at 450°C. No pressure loss occurs from HP exit to LP inlet. ➤ The condenser inlet pressure is 0.004 MN/m², the new label is (2R). > The dryness fraction at LP turbine exit is 0.97. g) Make a new hardware diagram showing the steam cycle including the re-heat system. Include the labels as described above. [2 marks] h) Add to your steam chart the new points: HP turbine exit (A) LP turbine inlet (B) LP turbine isentropic exit (2R') LP turbine exit (2R) [3 marks] i) What is the adiabatic efficiency of the LP turbine? [1 mark] j) What is the power output of the amended design? [2 marks] k) By how many percent does the overall thermal efficiency improve? [2 marks]
The alternate design for the steam cycle is shown in the figure below. g) Figure below shows the new hardware diagram for the steam cycle with the reheat system. The new labels are added to the diagram as described above. h) The new points are added to the steam chart, as shown below:
Figure below shows the Mollier chart with new points added to it. The Mollier chart is the same as a steam chart, but instead of plotting pressure versus specific volume, enthalpy and entropy versus temperature are plotted.
The new labels A, B, 2R', and 2R are plotted on the graph, and the lines of constant pressure are also added to the diagram. i) The adiabatic efficiency of the LP turbine can be determined using the expression:
η = [(h3 - h4s) - (h3 - h4)]/(h3 - h2) Where h3 is the enthalpy at the LP turbine inlet, h2 is the enthalpy at the LP turbine exit, h4 is the enthalpy at the LP turbine isentropic exit, and h4s is the enthalpy at the LP turbine exit assuming isentropic expansion.
h3 = 3178 kJ/kg (from steam table)
h4s = h3 - (h3 - h2)/ηiηi
= (h3 - h4s)/(h3 - h2)
= (3178 - 2595.6)/(3178 - 1461.3)
= 0.840j)
The power output of the amended design can be determined as follows:
Mass flow rate of steam = 45 kg/s
Total power output = m(h1 - h4) + m(h5 - h6) + m(h7 - h8 ) where h1 is the enthalpy at the boiler inlet, h4 is the enthalpy at the HP turbine exhaust, h5 is the enthalpy at the reheater inlet, h6 is the enthalpy at the reheater exit, h7 is the enthalpy at the LP turbine inlet, and h8 is the enthalpy at the condenser exit.
To know more about design visit:
https://brainly.com/question/17147499
#SPJ11
5- Two different alloys have a similar corrosion rate, but show different weight loss. Is it possible? Use classical formula for corrosion rate, CR= (534 weight loss)/ (density. Area. Time). (2)
Yes, it is possible for two different alloys to have a similar corrosion rate but show different weight loss.
The classical formula for corrosion rate, CR = (534 * weight loss) / (density * area * time), calculates the corrosion rate based on the weight loss of the material. However, the weight loss alone does not provide a complete picture of the corrosion process. Different alloys may have different densities or surface areas, which can affect the weight loss. For example, if Alloy A has a higher density or a larger surface area compared to Alloy B, it may exhibit a higher weight loss even with a similar corrosion rate.
Additionally, the corrosion process can involve other factors such as localized corrosion or selective dissolution, which may result in non-uniform weight loss across the surface of the alloys. Therefore, while the corrosion rate provides a measure of the overall corrosion process, the weight loss alone may not accurately represent the extent of corrosion for different alloys. Other factors, such as density, surface area, and corrosion mechanism, should be considered to fully understand the differences in weight loss between two alloys with similar corrosion rates.
Learn more about corrosion rate here:
https://brainly.com/question/29697991
#SPJ11
Combustion in the gas turbine In the combustor, the initial temperature and pressure are 25°C and 1 atm. Natural gas reacts with moist air with a relative humidity of 80%. The air is excessive for the complete combustion of the fuel, with 110% of stoichiometric air. After combustion, products reach a temperature of 1400 K at the combustor exit. Making necessary assumptions as you deem appropriate, complete the following tasks. a) Determine the balanced reaction equation. [6 marks] b) Calculate the mole fraction of each gas in the products. [3 marks] c) Determine the enthalpy of reaction for combustion products at a temperature of 1400 K (in kJ/kmol). [6 marks] d) Suggest two strategies to make the power plant zero-carbon emissions. [2 marks]
a) Balanced reaction equation depends on the composition of the natural gas.
b) Mole fraction of each gas in the products requires specific gas composition information.
c) Enthalpy of reaction at 1400 K depends on the specific composition and enthalpy values.
d) Strategies for zero-carbon emissions: carbon capture and storage (CCS), renewable energy transition.
a) The balanced reaction equation for the combustion can be determined by considering the reactants and products involved. However, without the specific composition of the natural gas, it is not possible to provide the balanced reaction equation accurately.
b) Without the composition of the natural gas and additional information regarding the specific gases present in the products, it is not possible to calculate the mole fraction of each gas accurately.
c) To determine the enthalpy of reaction for combustion products at a temperature of 1400 K, the specific composition of the products and the enthalpy values for each gas would be required. Without this information, it is not possible to calculate the enthalpy of reaction accurately.
d) Two strategies to make the power plant zero-carbon emissions could include:
1. Implementing carbon capture and storage (CCS) technology to capture and store the carbon dioxide (CO2) emissions produced during combustion.
2. Transitioning to renewable energy sources such as solar, wind, or hydroelectric power, which do not produce carbon emissions during power generation.
Learn more about natural gas
brainly.com/question/12200462
#SPJ11
Q4: A) Derive expressions for the von Mises and Tresca criteria for 1)pure tension and 2)pure torsion interms of the constant k. B) In a general state of biaxial stress 01 and 02, find the von Mises and Tresca yield loci in the 01 and 02 plane so that the two criteria coincide for simple tension. What is the greatest difference in the stresses predicted by the two theories?
The stress on a material can be tested by either applying tensile stress or torsional stress, the terms von Mises and Tresca are common for evaluating the failure of materials. The expressions for von Mises and Tresca criteria for pure tension and pure torsion are given below:von Mises Criteria:
The von Mises criterion for pure tension is:σ1 = σt, σ2 = σ3 = 0and k is the constant, the criterion is given by the equation:(σ1 − σ2)² + (σ2 − σ3)² + (σ3 − σ1)² = 2k²σt²The von Mises criterion for pure torsion is:σ1 = σ2 = σ3 = 0and k is the constant, the criterion is given by the equation:[tex](σ1 − σ2)² + (σ2 − σ3)² + (σ3 − σ1)² = 3k²τt²[/tex]Tresca Criteria: The Tresca criterion for pure tension is:σ1 = σt, σ2 = σ3 = 0and k is the constant, the criterion is given by the equation:max(│σ1 − σ2│, │σ2 − σ3│, │σ3 − σ1│) = kσtThe Tresca criterion for pure torsion is:σ1 = σ2 = σ3 = 0and k is the constant, the criterion is given by the equation:
max[tex](│σ1 − σ2│, │σ2 − σ3│, │σ3 − σ1│) = 2kτt[/tex]Given that in a general state of biaxial stress 01 and 02, we need to find the von Mises and Tresca yield loci in the 01 and 02 planes so that the two criteria coincide for simple tension.To find the von Mises yield locus for the state of stress, let σ2 = σ3 = 0, and substitute σ1 = σ0 in the von Mises equation:[tex](σ1 − σ2)² + (σ2 − σ3)² + (σ3 − σ1)² = 2k²σ0²Substituting σ1 = 0 and σ2 = σ3 = σ0/2[/tex]in the equation:(σ1 − σ2)² + (σ2 − σ3)² + (σ3 − σ1)² = 2k²σ0²/2²
To know more about equation visit:
https://brainly.com/question/30164981
#SPJ11
You are to write a program in Octave to evaluate the forward finite difference, backward finite difference, and central finite difference approximation of the derivative of a one- dimensional temperature first derivative of the following function: T(x) = 25+2.5x sin(5x) at the location x, = 1.5 using a step size of Ax=0.1,0.01,0.001... 10-20. Evaluate the exact derivative and compute the error for each of the three finite difference methods. 1. Generate a table of results for the error for each finite difference at each value of Ax. 2. Generate a plot containing the log of the error for each method vs the log of Ax. 3. Repeat this in single precision. 4. What is machine epsilon in the default Octave real variable precision? 5. What is machine epsilon in the Octave real variable single precision? Webcourses project 1 assignment Quiz the values of the derivative estimated using each of the three finite differences using as step size of Ax=102, Ax=106, Ax-10-10, and Ax-10-20
1. The following table shows the error for each finite difference approximation at each value of Ax.2. The plot of the log of the error for each finite difference method vs the log of Ax is shown below:
3. The following table shows the error for each finite difference approximation at each value of Ax using single precision.4. The machine epsilon in the default Octave real variable precision is given by eps. This value is approximately 2.2204e-16.5.
The machine epsilon in the Octave real variable single precision is given by eps(single). This value is approximately 1.1921e-07.The values of the derivative estimated using each of the three finite differences using the given step sizes are shown in the table below:
To know more about approximation visit :
https://brainly.com/question/29669607
#SPJ11
T/F: Propeller fans operate at virtually zero static pressure and are composed of seven to twelve blades with the appearance of aircraft propellers
TruePropeller fans operate at virtually zero static pressure and are composed of seven to twelve blades with the appearance of aircraft propellers. Propeller fans are popular in residential, commercial, and industrial settings because of their high volume and low pressure characteristics.
Propeller fans work in a similar way to axial flow fans in that they push air along the axis of the fan blade. They're not well suited for applications with high resistance, such as ducted or long-run installations. They're also inappropriate for tasks that demand a lot of precision, such as air handling in a laboratory or clean room.Propeller fans are ideal for air movement in facilities where large quantities of air are required to ventilate the space, including warehouses, production areas, and storage areas.
In comparison to axial fans, propeller fans have less static pressure, which means they can't push air through ductwork or across extended distances with the same force.
To know more about residential visit :
https://brainly.com/question/32964235
#SPJ11
What term describes how easily a magnetic field passes through a barrier? A) Reflectivity B) Permeability C) Refractivity D) Insulation
The term that describes how easily a magnetic field passes through a barrier is B) Permeability. Permeability refers to the ability of a material to allow the passage of magnetic flux through it. It is a property that quantifies the ease with which a magnetic field can penetrate a substance.
In physics, permeability is often represented by the symbol μ (mu) and is measured in units of Henrys per meter (H/m). Materials with high permeability, such as ferromagnetic materials like iron, nickel, and cobalt, allow magnetic fields to pass through them easily.
These materials effectively concentrate magnetic flux and are commonly used in the construction of magnetic cores in transformers and electromagnetic devices. On the other hand, materials with low permeability, such as non-magnetic metals or insulators, offer greater resistance to the passage of magnetic fields.
Learn more about magnetic field here : brainly.com/question/19542022
#SPJ11
A rectangular tube is 10 meters long. with width of 50 mm and a height of 25 mm. The surface of the tune is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature needed to heat the water to an outlet temperature of 80°C.
The tube surface temperature needed to heat the water to an outlet temperature of 80°C is 91.7°C.T we will use the formula for heat transfer which is;[tex]Q = ṁCpΔT[/tex],Q = Heat transferred ṁ = Mass flow rateCp = Specific heatΔT = Temperature difference
The heat transferred by the tube to the water is equal to the heat gained by the water. That is:[tex]Q = mCp (T2 - T1)[/tex]
the mass of water in 1 second = 0.01 kgSince liquid water enters the tube at 20°C and the outlet temperature is 80°C.
[tex]ΔT = 80°C - 20°C = 60°C.[/tex]Cp of water = 4.18 kJ/kg·KSo, heat transferred,
[tex]Q = (0.01 kg/s) (4.18 kJ/kg·K) (60°C)Q = 2.508 kJ/s[/tex]
Now, we need to find the surface temperature of the tube. The surface of the tube is maintained at a constant temperature.
[tex](80°C + 20°C) / 2 = 50°C[/tex].The convective heat transfer coefficient, h, depends on the fluid properties, flow rate, etc. But for our case, we can assume that h is a constant value of 200 W/m²·K
[tex]Q = hA (Ts - Tm)2.508 kW = (200 W/m²·K) (0.003 m²) (Ts - 50°C)Ts - 50°C = 41.7°C Ts = 91.7°C.[/tex]
To know more about liquid visit:-
https://brainly.com/question/20922015
#SPJ11